Page 1
1
PSD-63-IP
PAR LED PROJECTOR RGBWA-UV FULL COLOUR 6-IN-1
Thank you for purchasing our PSD-63-IP. Please read
these instructions carefully before you begin and operate
the fixtures according to these instructions to avoid any
possible damages and accidents causes by mis-use.
USER’S MANUAL
Page 2
2
1. Summary ....................................................................... 3
2. Safety Instruction .......................................................... 3
3. Outside Size Picture ..................................................... 4
4. Main Function ............................................................... 5
5. DMX Control Function ................................................... 5
6. Display Operation instructions ...................................... 8
7. Menu Tree .................................................................... 8
8. XLR cable connecting ................................................... 12
9. Connecting picture ........................................................ 13
10. Trouble Shooting ......................................................... 14
Index
PLEASE READ OVER THIS MANUAL
BEFORE OPERATING THE LIGHT
Page 3
3
1. Summary
2. Safety Instructions
Product introduction
The LED PSD-63-IP light uses casting aluminum housing, designed in a fashion of hydrodynamic
form. Appearance shows. It adopts high power 6-in-1 LED, which refers to single LED is made of
R,G,B,A,W,UV 6-IN-1 LED, And long life span, low consumption, good color mixing effect and high
brightness are the most prominent features. Each kind of LED can be independently dimmed. The
built-in program includes dimming, strobe, eotic, gradual change, fading and so on. It uses power
switch, performs low weight and consumption, stable capability and long life. International standard
DMX 512 signal is requested.
Packing List
• PSD-63-IP ................................................................................ 1 PC
• DMX Signal Cable .................................................................... 1 Set
• Waterproof input power cable .................................................. 1 PC
• User Manual
• Warranty Card
Safety Notes
• Ask a skilled technician before any repair.
• Always make sure the power is disconnected from the source before setting up, serving and
moving.
• Avoid direct eye exposure to the fixture when it is on.
Safety instructions
• Make sure the power supply voltage are consistent with this lights
• Ensure the use of voltage is in the range of the request technical parameter.
• Before the installation, please check the light’s fasteners and mechanical structure have been
received in good condition and appear no damage.
• This light is designed for indoor use; working temperature is lower than 40 degree.
• The fixtures maybe mounted in any position provided there is adequate room for ventilation.
Make sure there are no inflammable and explosive items (ornaments) in 0.5 meters away.
• Yellow / green cabling earthling safety; no flicker when the fixture is working on.
Page 4
4
3. Outside Size Picture
Page 5
5
4. Main Functions
• Input voltage: AC 100V-264V/47-63HZ
• Consume: 40W
• Lamp Type: 12W LED 6-in-1 RGBAWUV
(3PCS)
• Life span: 50000~100000hours
• PWM Dimmer: 1500HZ(16666 grades)
• Control Signal: DMX512
• Control mode: stand alone/ sound activated
• Channel: 12CH*, 12CH, 9CH, 7CH 6CH 5CH
4CH
• Function Effect: dimmer, strobe, gradual
change
• Cooling mode: Natural Convection
• Anti-electricity intension: 1.5KV
• Insulation Resistance:>2MΩ
• Size: 181*129.4*200.5mm
• Net Weight: 1.8 Kg
• Beam Angle: 15°,25°,45° Optional
5. DMX Control Functions
Additional:
Touch buttons, automatic lock key.
Built-in temperature control measurement function, when LED work overheated, intelligent reduce LED output power, current power output can be viewed.
4CH 5CH 6CH 7CH 9CH 12CH
12CH*
Recommended
VALUE FUNCTION
- CH1 - CH1 CH1 CH1 CH1 0-255
Dimming all
- - - - CH2 CH2 CH2
0-5
No strobe
6-20
Random burst strobe(s-
low to fast)
21-60
Normal strobe(slow to
fast)
61-100
Electronic Sine wave(s-
low to fast)
101-140
Random Strobe(slow to
fast)
141-180
Opening pulse(slow to
fast)
181-220
Closing pulse(slow to
fast)
221-255
Electronic Square wa-
ve(slow to fast)
CH1 - CH1 CH2 CH3 CH3 CH3 0-255
Red
CH2 - CH2 CH3 CH4 CH4 CH4 0-255
Green
CH3 - CH3 CH4 CH5 CH5 CH5 0-255
Blue
Page 6
6
- CH2 CH4 CH5 CH6 CH6 CH7 0-255
Amber
CH4 CH3 CH5 CH6 CH7 CH7 CH6 0-255
White
- CH4 CH6 CH7 CH8 CH8 CH8 0-255
UV
- - - - -
CH9(CH9
prior to CH11)
CH9(CH9
prior to
CH11)
0-10
No effect
11-15
CT01
16-20
CT02
21-25
CT03
26-30
CT04
31-35
CT05
36-40
CT06
41-45
CT07
46-50
CT08
51-55
CT09
56-60
CT10
61-65
AUTO 1 (R,G,B,A,W,U-
V,RG,RB,GB,AW,WU-
V,AUV)
66-70
AUTO 2 (R ,R ,G ,G
,B ,B ,A ,A ,W ,W
,UV ,UV )
71-75
AUTO 3 (R G ,R G
,R B ,R B ,B G ,B
G )
76-80
AUTO 4 (R ,G ,B W
,R G B W )
81-85
AUTO 5 (Rainbow effect:
B,BG ,BG,B G,G
,GR,GR,G R,R,RB
,RB,RB)
86-90
CHASE 1
91-95
CHASE 2
96-100
CHASE 3
111-2 00
R:111-115,G:116-
120,B:121-125,A:126-
130,W:131-135,UV:136-
140,YELLOW:141-
145,PINK:146-150,C-
YAN:151-155,ORAN-
GE:156-160,VIOLET:161-165,GOLDEN:166-170,270-
0K:171-175,3200K:176-
180,4000K:181185,5500K:186-
190,6500K:191-195,RG-
BW:196-200
201-255
Reserved
Page 7
7
- - - - - CH10 CH10 0-255
0-255(S),(speed of
AUTO,fast to slow when
AUTO1-AUTO5 effective
- CH5 - - -
CH11 (RGB
color mixing
instead of
RGB chan-
nels)
CH11
(RGB co-
lor mixing
instead
of RGB
channels)
0-10
No effect
11
Blue (Blue=full, Red+-
Green=0)(step)
12-50
Red=0, Green->up,Blue
=full(proportional)
51
Light Blue (Red=0,
Green=full, Blue =full)
(step)
52-90
Red=0, Green=full,
Blue->down(proportio-
nal)
91
Green (Red=0, Green=-
full, Blue =0)(step)
92-130
Red->up, Green=full,
Blue=0(proportional)
131
Yellow (Red=full,
Green=full, Blue=0)
(step)
132-170
Red=full, Green->down,
Blue=0(proportional)
171
Red(Red=full, Green=0,
Blue=0(step)
172-210
Red=full, Green=0,
Blue->up(proportional)
211
Magenta (Red=full,
Green=0, Blue=full)
(step)
212-250
Red -> down, Green=0,
Blue=full(proportional)
251-255
Blue (Red=0, Green=0,
Blue=full)(step)
- - - - CH9 CH12 CH12
0-10
Use the dimmer mode
which menu had set up
11-2 0
Linear curve
21-30
Square law curve
31-40
Inverse square law
curve
41-50
S-curve
51-60
Linear curve and smoo-
th
61-70
Square law curve and
smooth
71-80
Inverse square law cur-
ve and smooth
81-90
S-curve and smooth
91-255
Use the dimmer mode
which menu had set up
Page 8
8
6. Display Operation
• MENU : access the menu or return to a previous
menu option
• ENTER: select the current menu option
• UP: menu selection or parameter increments
• DOWN: menu selection or parameters decrease
7. Menu Tree
Tab Level 1 Level 2 Level 3 Level 4
ADDR(Address) 001-512
STAT(Static control) R 0-255*
G 0-255*
B 0-255*
A 0-255*
W 0-255*
UV 0-255*
SHUT 0-255*
PRSC(Preset
color)
NONE,R,G,B,A,W,UV,YELLOW,PINK,CYAN,ORANGE,VIOLET,GOLDE
N,2700K,3200K,4
000K,5500K,650
0K,RGBW*
SET(Set) CAL(Calibra-
tion)
R(Red) 0-255
G(Green) 0-255
B(Blue) 0-255
A 0-255
W 0-255
UV 0-255
Page 9
9
USE YES/NO
CHMD(Channel mode)
12CH *
12CH
9CH
7CH
6CH
5CH
4CH
DIM(Dimming
mode)
LIN/SQR/ISQR/
SCUR/LIN. /SQR./
ISQR/SCUR.
DISY(Display
set)
ON(Permanent on)
2MIN (2 minutes
off)
CTST(Custom color set) CT01 R(Red) 0-255
. G(Green) 0-255
. B(Blue) 0-255
. A 0-255
. W 0-255
. UV 0-255
CT10
AUTO(Auto) AT01 0-255*
AT02 0-255*
AT03 0-255*
AT04 0-255*
AT05 0-255*
CHS1 RUN..*
CHS2 RUN..*
CHS3 RUN..*
PROG Program CHS1 Chase 1 SC01 Scene 1 R(Red) 0-255
. . G(Green) 0-255
. . B(Blue) 0-255
. . A 0-255
. . W 0-255
. . UV 0-255
. . SHUT 0-255
. . AUTO NONE,
AT01-AT05
. . ATSP 0-255(S)
. . TIME 0-255(S)
. . WAIT 0-25.5(S)
. . USE YES/NO
Page 10
10
Instructions:
When enter to the “*” position displayed on the LED, the light will automatically set as master and
send data to external. Other fixtures can receive this data and will synchronously running without
manually set as slave. When power cycle it will jump to the “*” position and running again. And in
these position it will not return back to the default display after two minutes.
6.1 DMX ADDRESS SETTING
1) Press the ENTER button in ADDR menu, then enter to the DMX address setting.
2) Press theUP/DOWN button to select 1-512 numerical value.
3) Press the ENTER button to escape and save.
6.2 STATIC SETTING
1) Press the ENTER button in STAT menu, then enter to the static setting.
2) Press the UP/DOWN button to select RED GREEN BLUE AMBER,WHITE, UV and SHUT.
3) Press the UP/DOWN button to set up the 0-255 numerical value.
4) Press the ENTER button to escape and save.
6.3 COLOR CAST CALIBRATION SETTING
1) Press the ENTER button in CAL menu, then enter to the color cast calibration setting.
2) Press the UP/DOWN button to select RED GREEN BLUE AMBER, WHITE,UV
3) Press theUP/DOWN button to set up the 0-255 numerical value.
4) On the USE interface, pressing YES button means valid, NO means invalid.
5) Press the ENTER button to escape and save.
Illustrations: When pressing the YES button which means valid on the USE interface, the actual output value of RED GREEN BLUE AMBER,WHITE, UV is output in accordance with the percentage
which the color cast calibration value divides 255.
6.4 CHANNEL MODE SETTING
1) Press the ENTER button in CHMD menu, then enter to the channel mode setting.
2) Press theUP/DOWN button to select 12CH 9CH 7CH 6CH 5CH 4CH
3) Press the ENTER button to escape and save.
6.5 DIMMING MODE SETTING
1) Press the ENTER button in DIM menu, then enter to the dimming mode setting.
2) Press the UP/DOWN button to select LIN SQR ISQR SCUR LIN. SQR. ISQR. and SCUR.
3) Press the ENTER button to escape and save.
Illustrations: When settingLIN SQR. ISQR. and SCUR. in DIM menu, there will be added a little
delay dimming effect for smooth.
Dimming curve:
. SC20 Scene 20
CHS3 Chase 3
INFO Information SOFT(Software
version)
Vx.x
POW(Power
reduction)
100%/80%/50%
LOAD(Load) ST L Setting
load)
YES/NO
PR L Program
load)
YES/NO
SEND(Send) YES/NO
Page 11
11
Linear curve
square law
curve
Inverse
Square law
curve
S-curve
6.6 DISPLAY SETTING
1) Press the ENTER button in DISY menu, then enter to the display setting.
2) Press the UP/DOWN button to select ON 2 MINITES OFF
3) Press the ENTER button to escape and save.
6.7 CUSTOM COLOR SETTING
1) Press the ENTER button in CTST menu, then enter to the custom color setting.
2) Press the UP/DOWN select CT01…CT10
2) Press the UP/DOWN button to select 1-512 numerical value.
3) Press the ENTER button to escape and save.
6.8 AUTO RUN, SELF-PROGRAM RUN
1)Press the ENTER button in AUTO menu, then enter to the auto run,self-program run.
2)Press the UP/DOWN button to select AT01…AT05 SPEED CHASE01…CHASE03
3)Press the ENTERbutton to start running.
6.9 EDIT SELF-PROGRAM
1) Press the ENTER button in PROG menu, then enter to the edit self-program.
2) Press the UP/DOWN button to select CHASE01…CHASE03
3) Press the ENTER button for confirmation and enter to the next menu.
4) Press the UP/DOWN button to select SCENE01…SCENE20
5) Press the ENTER button for confirmation and enter to the next menu.
6) Then press the UP/DOWN button to selectRED…SHUT TIME WAIT USE
7) Press the UP/DOWN button to set up the parameter which are needed.
8) Press the ENTER button t o escape and save.
Illustrations When USE is set to be NO or the parameter of TIME is 0, it will not run this scene.
When WAIT is set to be FADE time, the running process isas the following chart showing.
6.10 CHECK THE LIGHTING INFORMATION
1) Press the ENTER button in INFO menu, then enter to the checking the lighting information.
2) SOFT button is for software version information.
3) POW button is for the current information of power reduction. It is 100% output in normal conditions, but 80% or 50% output in over temperature protection situation.
Page 12
12
8. XLR Cable Connecting
XLR cable:
The standard connection way of the XLR is: one end connects to the male plug, and the other connects to the female. As below: pin 1: ground, pin 2: negative signal, pin 3: positive signal
Note: In order to avoid failures and interference signal transmission, we connect a
resistance120Ω (1/4W) at the end of the DMX connecting as below:
6.11 LIGHTING SETTING PARAMETER RESET
1) Press the ENTER button in ST L menu, then enter to the lighting setting parameter reset.
2) Press the UP/DOWN button to select YES.
3) Press the ENTER button to escape and save.
Illustrations “ADDR” “CTST” and “PROG” are not reset, the others reset to the underlined value of
the word.
6.12 PROG SELF-PROGRAMMING PARAMETER RESET
1) Press the ENTER button in PR L menu, then enter to the PROG self-programming parameter
reset.
2) Press the UP/DOWN button to select YES.
3) Press the ENTER button to escape and save.
6.13 LIGHTING PARAMETER DOWNLOADING EACH OTHER VIA DMX CABLE
1) Press the ENTER button in SEND menu, then enter to sending parameter to other lightings.
2) Press the UP/DOWN button to select YES.
3) Press the ENTER button to confirm sending.
Illustrations
1)Please disconnect the connection of projector and DMX console before sending the parameter.
2)The information of ADDR CAL can’t be sent, can’t be downloaded each other.
3)There will be an automatic reset of the other projectors after receiving parameter correctly.
Page 13
13
The Conversion between 3 pin and 5 pin XLR:
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to 3PIN cable.
9. Connecting Picture
Light connecting picture
Page 14
10. Trouble Shooting
PROBLEM REASON AND ACTION
The lighting can’t be started normally
Check the power connection is correct or not.
Please detect the voltage.
Power supply is damaged or incorrect
connected. Call a qualified personnel
to fix it.
Connection of control board is not
correct. Call a qualified personnel to
fix it.
Out of console’s control
Please check the DMX connector and
the power connection is connected
correctly or not. It means having signal if it shows twinkling of the decimal
point which in the lower right corner
of the screen when exiting the screen
saver.
Please check the DMX address setting of lighting is correct or not.
Out of console’s control
Check CHMD setting is correct or not.
Please check whether the DMX line
is near to the high voltage wire or not.
In that case, it will damage or interfere
the DMX electric circuit.
The beam appears dim ,the brightness declines obviously
Check whether the CAL is started or
not and the set value is too small.
Check whether the POW is in over
temperature protection situation or
not, if yes, please take measures for
ventilation.
Note: only professionals should manipulate this equipment as above
Loading...