Elan MC Installation Manual

Download

Page 1

SPEAKER I

NSTALLATION

MANUAL

MC Models ONLY

Page 2

ELAN HOME SYSTEMS

INSTALLATION MANUAL

Introduction

M Series by ELAN: An In-Wall Speaker Line of Distinction . . . . . . . . . . . . . . . . .2

Installation Overview

About the M Series "Mounting Clamp" Design . . . . . . . . . . . . . . . . . . . . . . . . . .3

Damping the Wall Cavity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Painting the Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation Procedures

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cutting Speaker Openings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

In-Ceiling Speaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

In-Wall Speaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4, 5

Installing the IR Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

M Series Specifications

M Series Cutout Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

M Series Specifications and Driver Components . . . . . . . . . . . . . . . . . . . . . . . . .8

Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

TABLE OF

CONTENTS

Page 3

ELAN HOME SYSTEMS

INSTALLATION MANUAL

The ELAN M Series is a multi-tiered speaker offering that achieves a new level of design flexibility and acoustical performance.

True quality begins with a discriminating eye toward the goal. The goal? To deliver a line of in-wall and in-ceiling speakers with superior performance at all price levels.

The process began by assessing every major name brand in-wall speaker for performance, price, aesthetics and attention to detail. From there it went to the lab–– listening, evaluating, analyzing, comparing, debating, formulating, reformulating and defining.

We hired world-class acoustical engineers to refine our conclusions. We summoned expert dealers to test the design decisions, assortment and product attributes. We then selected the finest materials at each cost level to create a consistent offering. The materials were carefully tested and voiced against the nearest competitive speaker to arrive at the best performance against every model offered in each class.

The result: speakers second to none in every class from basic to premium grade. In fact, the M Series are the top performers in each cost class. Better sound, better looks, and better quality at a given price.

DISCERNING FEATURES

Styling Perfection––Narrower flat-profiles, sharp-radius frames and tall aspect ratios make for a sleek, slim appearance on the wall. A fine-mesh grille finish adds to the elegant look of the M Series products.

Acoustical Mastering––Balance across the full range of the musical spectrum requires a sophisticated selection of the right woofer cones, surrounds, tweeters, crossover components and baffle construction for each system. Most importantly, each crossover has been "voiced" to provide the best performance for the materials deployed.

Installation Provisions––Getting the speaker in the wall solidly and efficiently is beneficial to its end use. The multi-legged clamp system provides the best means for eliminating undesirable vibration common with other speaker alternatives.

A Family of Performers––When multiple speakers from other manufacturers were tested, the range of performance fell off considerably between models. No one company exceeded average performance with all models in the given class. M Series provides above average performance with all models - with no under performers in the entire lineup.

Listen with Confidence––All M Series speakers come with a Limited Lifetime Warranty.

Enjoy Your Choice––You are about to experience music reproduction few expect from an in-wall speaker. Sit back and listen, and savor the resounding quality that your new ELAN speakers deliver. We are pleased to be able to provide you with many pleasurable moments for years to come. Thank you for your selection of M Series––and enjoy the music.

M SERIES BY

ELAN:

AN I

N-WALL SPEAKER

LINE OF DISTINCTION

Page 4

ABOUT THE M SERIES MOUNTING CLAMP DESIGN

All models in the ELAN M Series speaker line feature rigid, heavy-duty mounting clamps that ensure a quick, secure, vibration-free installation in walls from 1/2" to 1-1/2" in thickness.

The ceiling models and 5.25" In-Walls have four mounting clamps each. The 6.5" and 8" In-Wall models have six mounting clamps.

DAMPING THE WALL CAVITY

Damping the wall/ceiling cavity behind the speakers by loosely filling it with fire-rated fiberglass insulation can enhance the performance of your M Series speakers and reduce unwanted transmission of sound into adjacent rooms.

PAINTING THE SPEAKERS

All ELAN M SERIES speakers can be finished to match any room décor. Their white, textured frames and no-rust aluminum grilles readily accept most water-based interior latex and spray enamels.

We recommend the grille and frame be painted separately. To aid in frame painting, we’ve included a plastic paint shield that will protect the speaker baffle.

Painting Tips:

1. If not using spray paint, we recommend that the paint be thinned to prevent clogging the speaker grille perforations.

2. When painting, several light coats will yield the best results.

As the installation of flush-mount speakers requires cutting into walls where highvoltage wiring, pipes and duct work may be present, installation should be performed by experienced and trained professionals only.

NOTES:

• Check for Obstructions––Before cutting

holes in any existing wall or ceiling surface, the cavity behind each speaker’s installation location MUST be probed for obstructions. Make sure to probe both speaker locations in the room to ensure that symmetrical placement is feasible.

•Always maintain proper polarity when wiring speakers. Failure to do so will result in poor stereo imaging and a decrease in base response.

CUTTING SPEAKER OPENINGS IN FINISHED WALLS

1. Use a stud finder to locate the studs around the intended speaker placement. NOTE: A stud-finding device MAY NOT detect pipes, wiring, or other obstructions located behind the drywall.

2. Use the inside portion of the speaker cutout template to confirm the speaker placements.

3. Remove templates and drill or carefully poke a pilot hole in both locations. A bent piece of wire or a coat hanger may be use to probe the stud bay for obstructions. If you experience resistance of any kind––STOP! If any

ELAN HOME SYSTEMS

INSTALLATION MANUAL

INSTALLATION PROCEDURES

NSTALLATION

OVERVIEW

Page 5

ELAN HOME SYSTEMS

INSTALLATION MANUAL

obstructions are detected, patch the pilot holes and try again in another location.

4. Once you have determined the cavity is free from obstructions, re-position the cutout template and use a pencil to lightly trace the perimeter of the template. If installing an In-Wall speaker, use a level to accurately position the cutout before you trace its outline.

5. Use a keyhole saw, drywall router, or razor knife to cut the openings.

IMPORTANT NOTE: The slim design of M SERIES speaker frame flanges require that careful attention be paid to not oversize the cut-out hole.

IN-CEILING SPEAKER INSTALLATION:

Complete Assemblies

(with or without New Construction Brackets)

1. Remove speaker grille

2. Locate the speaker wire and pull through the wall opening.

3. Connect the speaker wire. BE SURE TO OBSERVE CORRECT POLARITY!

4. Insert the speaker into the opening In the ceiling and CAREFULLY tighten each of the four clamping screws, alternating

diagonally between each screw position to ensure proper fit and finish.

FIGURE 1

5. Replace the speaker grille.

IN-WALL SPEAKER INSTALLATION:

Complete Assemblies (with or

without New Construction Brackets)

1. Remove speaker grille.

2. Locate the speaker wire (and IR wire, if applicable) and pull through the wall opening.

FIGURE 1

CAUTION: DO NOT OVER-TIGHTEN THE SCREWS!

If using a drill to tighten the clamping screws, be sure to set the torque setting very low. Setting the drill’s torque too high may break the mounting clamps, the wall surface, and/or the speaker frame assembly.

Page 6

ELAN HOME SYSTEMS

INSTALLATION MANUAL

3. Install ELAN IR Tube if applicable (see

Installing the ELAN IR Tube, Page 6)

4. Connect the speaker wire. BE SURE TO OBSERVE CORRECT POLARITY!

5. Insert the speaker into the opening In the wall and CAREFULLY tighten each of the clamping screws (four on all 5 1/4" models, six on all 6 1/2" and 8" models), alternating diagonally between each screw position to ensure proper fit and finish. FIGURE 2

6. Replace the speaker grille.

INSTALLING THE ELAN IR TUBE IN M SERIES IN-WALL SPEAKERS

1. Locate IR knockout on face of speaker baffle.

2. Place the speaker FACE-DOWN on its carton

3. Using a 7/16” bit, drill the knockout free. FIGURE 3, Page 6

4. Trim away flash and rough edges.

5. Connect 12V, GND, and SIGNAL as per IR Tube instructions.

6. Press the tube firmly in place, and screw down until nearly flush with front of baffle. FIGURE 4, Page 6

FIGURE 2

CAUTION: DO NOT OVER-TIGHTEN THE SCREWS!

Page 7

ELAN HOME SYSTEMS

INSTALLATION MANUAL

FIGURE 3

FIGURE 4

NOTE: Due to the grill, IR receiving range will be reduced from 27 feet to approximately 15 feet.

Page 8

ELAN HOME SYSTEMS

INSTALLATION MANUAL

M SERIES SPECIFICATIONS AND DRIVER COMPONENTS

The ELAN M Series In-Wall/In-Ceiling Loudspeaker line is constructed using the finest materials available to provide a lifetime of listening enjoyment.

Specs MC (Level 1) ME (Level 2) MM (Level 3) MP (Level 4)

Tweeter PEI Silk Silk Aluminum and Material Magnesium

Composite

Woofer Cone Polypropylene Mineral Filled Injection Molded Woven Glass

Polypropylene Mica Fiber

Woofer Inverted Butyl Inverted Butyl Inverted Butyl Inverted Butyl Surround

Woofer Stamped Stamped Stamped Glass Fiber Basket Composite

Crossover 6dB/octave 6dB/octave 12dB/octave Linkwitz/Riley Response

Crossover None None Treble Treble/Bass Switches

Interconnect 20AWG 20AWG 18AWG 16AWG Wire

Input Spring Spring Gold-Plated Gold-Plated Connectors Terminals Terminals Push Terminals Push Terminals

Hardware Stainless Steel Stainless Steel Stainless Steel Stainless Steel

Nominal 8 Ohms 8 Ohms 8 Ohms 8 Ohms Impedance

Sensitivity 87dB 87-90dB 88-91dB 89-93dB Range (1W/1Meter) (1W/1Meter) (1W/1Meter) (1W/1Meter)

Power 5.25"= 5 - 40W 5.25"= 5 - 50W 5.25"= 5 - 60W Handling 6.50"= 5-50W 6.50"= 5 - 65W 6.50"= 5 - 75W 6.50"= 5 - 85W

8"= 5 - 80W 8"= 5 - 90W 8"= 5 - 100W

Page 9

ELAN HOME SYSTEMS

INSTALLATION MANUAL

M SERIES INSTALLATION GUIDELINES

5.25" Model Cutout Dimensions Dimensions w/ Frame Total Depth

Depth

ME525D 6-13/16" (173mm) diameter 8" (203mm) diameter 4-1/8" (104mm)

ME525C 6-13/16" (173mm) diameter 8" (203mm) diameter 4-1/8" (104mm)

ME525W 6-1/8" x 10-1/4" (156x260mm) 7-3/8" x 11-9/16" (187x294mm) 3-3/4" (94mm)

MM525C 6-13/15" (173mm) diameter 8" (203mm) diameter 4-1/4" (107mm)

MM525W 6-1/8" x 10-1/4" (156x260mm) 7-3/8" x 11-9/16" (187x294mm) 3-3/4" (94mm)

MP525W 6-1/8" x 10-1/4" (156x260mm) 7-3/8" x 11-9/16" (187x294mm) 3-3/4" (94mm)

6.50" Model Cutout Dimensions Dimensions w/ Frame Total Depth

MC650C 8-1/16" (205mm) diameter 9-1/4" (235mm) diameter 3-5/8" (92mm)

MC650W 7-1/8" x 12-1/4" (181 x 311mm) 8-1/4" x 13-1/2" (210 x 343mm) 3-5/16" (83mm)

ME650C 8-1/16" (205mm) diameter 9-1/4" (235mm) diameter 4-1/4" (107mm)

ME650W 7-1/8" x 12-1/4" (181 x 311mm) 8-1/4" x 13-1/2" (210 x 343mm) 3-3/4" (94mm)

MM650C 8-1/16" (205mm) diameter 9-1/4" (235mm) diameter 4-1/2 (111.5mm)

MM650W 7-1/8" x 12-1/4" (181 x 311mm) 8-1/4" x 13-1/2" (210 x 343mm) 3-3/4" (94mm)

MM650D 8-1/16" (205mm) diameter 9-1/4" (235mm) diameter 4-1/2" (111.5mm)

MP650 C 8-1/16" (205mm) diameter 9-1/4" (235mm) diameter 4-13/16" (122mm)

MP650 W 7-1/8" x 12-1/4" (181 x 311mm) 8-1/4" x 13-1/2" (210 x 343mm) 3-13/16" (96mm)

8" Model Cutout Dimensions Dimensions w/ Frame Total Depth

ME800C 9-3/4" (248mm) diameter 11" (278mm) diameter 4-13/16" (122mm)

MM800C 9-3/4" (248mm) diameter 11" (278mm) diameter 4-13/16" (122mm)

MM800W 8-5/8" x 15-3/16" (219 x 386mm) 9-7/8" x 16-1/2" (251 x 419mm) 4" (102mm)

MP800C 9-3/4" (248mm) diameter 11" (278mm) diameter 5" (127mm)

MP800W 8-5/8" x 15-3/16" (219 x 386mm) 9-7/8" x 16-1/2" (251 x 419mm) 4" (101mm)

MP800S 8-5/8" x 15-3/16" (219 x 386mm) 9-7/8" x 16-1/2" (251 x 419mm) 4" (101mm)

MP800D 9-3/4" (248mm) diameter 11" (278mm) diameter 5-1/12" (139mm)

Page 10

www.elanhomesystems.com

2428 Palumbo Drive • Lexington, KY 40509

1.877.289.3526

Limited Lifetime Warranty

ELAN HOME SYSTEMS, L.L.C. ("ELAN") warrants to the original retail purchaser only that

all M Series speakers and speaker brackets will be free from defects in materials and

workmanship, provided that the product was purchased from an authorized ELAN Home

Systems Dealer.

If the above purchaser discovers such item was not as warranted above and promptly

notifies ELAN writing, ELAN shall repair or replace the items at the company’s option.

This warranty shall not apply (a) to equipment not manufactured by ELAN, (b) to equipment

which shall have been installed by other than an authorized ELAN installer, (c) to installed

equipment which is not installed to ELAN’s specifications, (d) to equipment which shall

have been repaired or altered by others than ELAN, (e) to equipment which shall have

been subjected to negligence, accident, or damage by circumstances beyond ELAN’s

control, including, but not limited to, lightning, flood, electrical surge, tornado, earthquake,

or any other catastrophic events beyond ELAN’s control, or to improper operation,

maintenance or storage, or to other than normal use of service. With respect to equipment

sold by, but not manufactured by ELAN, the warranty obligations of ELAN shall in all

respects conform and be limited to the warranty actually extended to ELAN by its supplier.

The foregoing warranties do not cover reimbursement for labor, transportation, removal,

installation, or other expenses which may be incurred in connection with repair or

replacement.

Except as may be expressly provided and authorized in writing by ELAN, ELAN shall not

be subject to any other obligations or liabilities whatsoever with respect to equipment

manufactured by ELAN or services rendered by ELAN.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE,

INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.