Elan EL-4KPM-V66-A1812 User Manual

Page 1
E L- 4 K P M - V 6 6 - A1 8 12
Video/Audio Premium Matrix
User Manual
Lock PTP
1Power
IR
2 3 4 5 6 7 8 All Menu Up Esc
Select
EL-4KPM-V66-A1812 PlatinumMatrix
Down Enter
EDID
In
Out
1 2 3 4 5 6 7 8
HDBT In
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
IR In
L/R Out
Coax. Out
1
2 3
4
5
6
IN
OUT
1 2 3 4 5 6
IR In
L/R Out
Coax. Out
IR In
L/R Out
Coax. Out
IR In
L/R Out
Coax. Out
IR In
L/R Out
Coax. Out
IR In
L/R Out
Coax. Out
IR In
IR Out
Global
TCP/IP
Ethernet
Tx
Rx
On/Off
In
Lock PTP
1Power
IR
2 3 4 5 6 7 8 All Menu Up Esc
Select
EL-4KPM-V66-A1812 PlatinumMatrix
Down Enter
EDID
In
Out
1 2 3 4 5 6 7 8
Page 2
PREMIUM SERIES USER MANUAL
02
www.elanhomesystems.com
Introduction 03
Features 03
Panel Descriptions 04
Matrix Main Com Board 05
Matrix HDBaseT Receiver Options 06
EDID Control 07
Terminating HDBaseT Cat Cable 08
Understanding the Matrix/Receiver Status Lights 08
Infrared Distribution 09
Infrared Remote Control 10
Application Diagram 11
Specifications 12
Package Contents 12
Maintenance 12
Infrared Commands 13-14
RS-232 and Telnet Commands 15-16
Certifications 17
Contents
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.
Safety And Performance Notice
The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY 1427071-6
EIA/TIA-568-B termination (T568B) of cables is recommended for optimal performance.
To minimize interference of the unshielded twisted pairs in the CAT5e/6 cable do not run the HDBaseT / Cat5e/6/6a cabling with or in close parallel proximity to mains power cables.
Do not substitute or use any other power supply other than the enclosed unit, or a ELAN approved replacement.
Do not disassemble either the Transmitter or Receiver units for any reason. Doing so will void the manufacturer’s warranty.
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
Page 3
03
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
Our Premium Series of HDBaseT matrix products offer the very best performance and flexibility for the custom installer. Built with the custom installer in mind, any combination of inputs and outputs can be specified to suit the exact AV distribution needs of the project. The ELAN EL-4KPM-V66-A1812 include both HDBaseT/HDMI inputs and outputs allowing extension of HDMI signal of up to 100m*. The built-in audio matrix with HDMI/analog/digital embedding and de-embedding further adds audio distribution capabilities enabling you to provide your clients with a feature rich solution.
Introduction
• 6x HDMI inputs which can be independently routed to 6x HDBaseT/HDMI video outputs
• 4K video support
• Supports distances of up to 100m @1080p & 70m @4K on a single CAT cable
• 1x HDBaseT input allowing sources to be located remotely using ELAN HDBaseT transmitters
• Supports POH (Power Over HDBaseT) to power ELAN transmitters and receivers - no local power supplies required
• LAN serving (Ethernet Switch) with compatible ELAN receivers
• Integrated 18 Input x 12 Output Audio Matrix
• Audio Return Channel (ARC) with compatible ELAN HDBaseT receivers
• Analog audio L/R embedding onto HDMI outputs
• HDMI Audio de-embedding to analog audio L/R + digital coaxial outputs
• Bi-directional RS-232 and IR from all input and output locations (with compatible ELAN transmitters and receivers)
• Web interface module for control & configuration of the matrix
• Control of Matrix via front panel, IR, RS-232 & TCP/IP
• Advanced EDID management
• HDCP 2.2 compliant
EL-4KPM-V66-A1812 Features:
Page 4
PREMIUM SERIES USER MANUAL
04
www.elanhomesystems.com
Rear Panel
1 HDMI inputs 1 to 6 – Connect HDMI
sources
2 HDBT input – Connect remote HDBT
transmitter
3 HDMI outputs 1 to 6 – Output for
displays.
4 HDBT outputs 1 to 6 – Output for
displays.
5 Ethernet-embedded for LAN serving to
all connected HDBT transmitters and receivers
6 RJ45 - TCP/IP control 7 Power switch 8 GND – Ground connection 9 RS232 port – Connect to this port
for the control of the matrix from a computer or control processor.
q L/R stereo inputs 1 to 6 – 3.5mm stereo
jack
w IR outputs 1 to 6 – 3.5mm mono jack
for routed IR emitter outputs for discrete source control.
e Coaxial Digital outputs 1 to 6 – RCA
connector.
r L/R stereo outputs 1 to 6 – 3.5mm
stereo jack.
t IR Inputs 1 to 6 – 3.5mm stereo jack for
integration with a control processor.
y RS232 Port – 1x 3-pin phoenix terminal
u Global IR Output – 3.5mm mono jack.
i Global IR Input – 3.5mm stereo jack.
o AC power input – 100V-240V input.
Front Panel
1 LCD display – Show the status of input
& output selection and EDID info.
2 IR receiver window – Receives IR from a
hand held remote control or processor.
3 Power LED indicator - Indicates the
power status of the matrix.
4 Power button – Press to toggle power of
the matrix on/off
5 HDMI output selection button 1 to 6 –
Press to select the output from 1 to 6.
6 All button for HDMI outputs – Press to
select all of the outputs from 1 to 6.
7 Menu button – Press to enter EDID
setup
8 Up – Press to change up through the
adjustable values.
9 ESC - Press to quit EDID set up menu. q Lock LED indicator - Indicate the status
of the key lock
w Lock button – Press to lock the buttons
on the front panel (Press and hold for 2 seconds)
e HDMI input selection button 1 to 6 –
Press to select the input from 1 to 6.
r PTP button-Press to mirror all inputs
and outputs (e.g. output 1 to input1, output 2 to input2 and so on).
t Select – Press to select an EDID
parameter to change. Selected segment will blink.
y Down – Press to change down through
the adjustable values
u Enter – Press to set EDID to specified
INPUT or copy EDID from specified OUTPUT to specified INPUT.
HDBT In
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDMI In
IR Out L/R In
Tx
Rx
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
1
2 3
4
5
6
IN
OUT
1 2 3 4 5 6
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
HDBT Out
HDMI Out
IR In
L/R Out
Coax. Out
IR In
IR Out
Global
TCP/IP
Ethernet
Tx
Rx
On/Off
In
Lock PTP
1Power
IR
2 3 4 5 6 7 8 All Menu Up Esc
Select
EL-4KPM-V66-A1812 PlatinumMatrix
Down Enter
EDID
In
Out
1 2 3 4 5 6 7 8
1
8 9 12 1510 13
11 14
16
17 18
2 3 5 6 74
Lock PTP
1Power
IR
2 3 4 5 6 7 8 All Menu Up Esc
Select
EL-4KPM-V66-A1812 PlatinumMatrix
Down Enter
EDID
In
Out
1 2 3 4 5 6 7 8
1 2
10 11 12 13 14 15 16
3 4 5 6 7 8 9
Panel Descriptions
Page 5
05
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
Matrix Main Com Board
The Matrix main communication board is located on the rear panel and has the following connections:-
Connections:
A. TCP/IP – For control of Matrix (RJ45 Connector)
B. Ethernet – Matrix includes 1x16 10/100 Ethernet switch (RJ45 Connector)
C. Global IR Input 3.5mm stereo jack
D. Global IR Output 3.5mm mono jack
E. RS-232 2-way (Phoenix Connector)
TCP/IP
The ELAN Matrix can be controlled via TCP/IP.
For full list of protocols please see ‘RS-232 & Telenet Commands’ located at the rear of this manual.
A ‘Straight-through’ RJ45 patch lead should be used
RS-232 2-Way
The ELAN matrix can be controlled via supplied 3-pin Phoenix to 9-pin serial cable
For full list of protocols please see ‘RS-232 & Telenet Commands’ located at the rear of this manual.
Details of RS-232 pin assignment and communication are below:
MT0808FAV REMOTE CONTROL
CONSOLE
PIN Assignment PIN Assignment
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
TCP/IP
A
B
C
D
E
Page 6
PREMIUM SERIES USER MANUAL
06
www.elanhomesystems.com
There are three HDBaseT receiver options that are compatible with the outputs on the ELAN Premium Series products.
Matrix HDBaseT Receiver Options
EL-4KHDBT-RX-40-IR
Basic HDBaset Receiver with 2-way IR pass-through. Supports distances up to 70m*.
• HDBaseT input/HDMI output
• IR Output 3.5mm mono jack
• IR Input 3.5mm stereo jack
HDMI Out
LINK
POWER
IR RX IR TX
12V
2A
EL-4KHDBT-RX-40-IR
HDBT In
LINK
HDMI Out
LINK
POWER
IR RX IR TX
12V
2A
EL-4KHDBT-R X-70-E-A RC-IR S
Premium HDBaseT receiver which features 2-way IR & RS232, HDMI ARC display distances up to 100m*. Only compatible with EL-4KPM-V88-A2416 and EL-4KPM-V66-A1812 ELAN Premium Matrix products.
• HDBaseT input/HDMI Output
• Optical Audio input (Toslink)
• 2-way RS232 (9-pin serial)
• IR Output 3.5mm Mono Jack
• IR Input 3.5mm Mono Jack
• 3x 10/100 Ethernet connections (RJ45)
HDBT In
IR TX IR RX
ARC
Optical
RS-232
15V
Power
2A
EL-4KHDBT-RX-70-E-ARC-IRS
HDBT In
IR TX IR RX
ARC
Optical
RS-232
15V
Power
2A
EL-4KHDBT-RX-70-E-ARC-IRS
Ethernet 1HDMI OutOptical In Ethernet 2 Ethernet 3
EL-4KHDBT-RX-40-IRS
Mid-Level HDBaseT receiver which has the same features as the EL-4KHDBT-RX-70-ARC receiver but with added 2-way RS-232 control.
• HDBaseT input/HDMI output
• 2-way RS232 (9-pin serial)
• IR Output 3.5mm mono jack
• IR Input 3.5mm stereo jack
EL-4KHDBT-RX-40-IRS
HDBT In
Standard
Upgrade
LINK POWER
12V 2A
EL-4KHDBT-RX-40-IRS
HDBT In
Standard
Upgrade
LINK POWER
12V 2A
HDMI Out
HDMI LINK
RS-232
IR RX IR TX
Page 7
07
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
EDID Control
EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by the source to find out what audio and video resolutions are supported by the display then from th is information the source will discover what the best audio and video resolutions need to be outputted.
While the objective of EDID is to make connecting a digital display to a source a simple plug and play procedure issues do arise when multiple displays or video matrix switching is introduced because of the increased number of variables.
By pre-determining the video resolution and audio format of the source and display device you can reduce the time need for EDID hand shaking thus making switching quicker and more reliable.
Configuration of the EDID settings can be achieved in one of three ways:
1 Via the Web GUI
2 Via Front Panel Buttons
a. Press MENU button
b. Panel will display ‘EDID settings. Press S ELECT button
c. Select the input you wish to fix the EDID on or select ‘All’. Use UP/DOWN
buttons to toggle selection and SELE CT button to confirm
d. Select video resolution required (4K, 1080p, 3D etc). Use UP/ DOWN
buttons to toggle selection and SELE CT button to confirm
e. Select audio format required (2.0, 5.1, 7.1). Use UP/DOWN buttons to
toggle selection and SE LECT button to confirm
3 Via Supplied IR Remote Control
a. Fixed EDID to INPUT / ALL INPUTS:
To select video resolution - Press 1080I /108 0 P/3D / 4K
To select Audio resolution - Press 2.0CH/5.1CH/7.1CH
To assign settings to individual input/all inputs – Press INPUT /
ALL button in ‘ZONE INPUT’ area of remote control
b. Copy EDID of any specific OUTPUT to any assigned INPUT or ALL INPUTS:
Press COPY button
Press OUTPUT zone button you wish to copy EDID from
Press INPUT zone button /ALL button to copy EDID to
c. User defined EDID to any INPUT or ALL INPUTS:
Press USER1/USER2 button
Press selected INPUT or ALL button to assign EDID
32 10
EDID T YPE
Combination of DIP positions
Copy EDID from output1
1080P 2.0CH
1080P 5.1CH
1080P 7.1CH
1080i 2.0CH
1080i 5.1CH
1080i 7.1CH
DVI 1280x1024
DVI 1920x1080
DVI 1920x1200
POWER
1
ALL PTP
OUTPUT
2 3 4
5 6 7 8
1
ALL
INPUT
2 3 4
5 6 7 8
1080i 1080p 3D 4K
USER1 USER2 FN1
EDID
FN2
2.0CH 5.1CH 7.1CH COPY
B
C
A
0
1
0 0 0
0 0 0
1
0 0 0
11
0 0
0 0 01
10 01
10 01
110 1
0 0 01
10 01
10 01
1101
0 01 1
101 1
1 01 1
111 1
4K60 Hz 4: 2:0 2.0CH
4K60 Hz 4: 2:0 5.1CH
4K60 Hz 4: 2:0 7.1CH
4K30Hz 4:4:4 2.0CH
4K30 Hz 4:4:4 5.1CH
4K30 Hz 4:4:4 7.1CH
Page 8
PREMIUM SERIES USER MANUAL
08
www.elanhomesystems.com
Terminating HDBaseT CAT cable
It is important that the interconnecting CAT cable between the ELAN HDBaseT products is terminated using the correct RJ45 pin configuration. The link CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable and it is advised that this is wired to the T568B wiring standard as this format is less prone to EMI (Electro-Magnetic Interference).
When installing CAT cables it is advised that you use the best possible CAT cable quality possible. HDMI distribution products will only work if used with CAT5e standard cable or above. ELAN recommends using a CAT6 cable for your installations, especially when running over longer distances, in areas of high EMI, or for 4K signal distribution.
RJ45 Wiring ­T568B
Understanding the Matrix / Receiver HDBaseT status lights
The ELAN Matrix and HDBaseT extender solutions include status LED indicators on both the Matrix and Receiver products to show all connections are active and to help diagnose possible problems.
Understanding the status lights:-
ELAN Matrix:
• The Yellow HDBaseT status link light will be off when the zone output has been turned off or there is a problem with the specific Matrix output.
• The Yellow HDBaseT status link light will blink when the zone output is on and working
• The Green HDBaseT link light will blink if there is an unstable connection between the ELAN Matrix and HDBaseT Receiver
• The Green HDBaseT link light will be lit when a there is an active HDBaseT Receiver connected to the Matrix
• The Green HDBaseT link light will be off when a there is no connection with a HDBaseT receiver
ELAN HDBaseT Receiver:
• The HDMI link light will be off when there is no connection with a display
• The HDMI link light will be on when there is an active connection with a display (NOTE - Not all HDBaseT RX feature a HDMI status LED)
• The HDBaseT link light will be off when there is no CAT cable/active HDBaseT connection on the RJ45 HDBaseT input
• The HDBaseT link light will blink if there is an unstable connection between the ELAN Matrx and HDBaseT receiver
• The HDBaseT link light will be lit when a CAT cable is connected to the HDBaseT RJ45 output on the Matrix and an active connection is
achieved with the ELAN HDBaseT Receiver.
Page 9
09
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
The ELAN Premium Series of matrix products include multiple options for control and routing of IR. As default setting IR is globally routed meaning that ALL IR inputs are routed to ALL IR outputs on both Matrix and HDBaseT Receivers and Transmitters.
IMPORTANT: The ELAN HDMI Premium, Matrix, & HDBaseT product lines utilize 5 volts to power an IR Receiver on the IR Input and include an EL-4KACC-IR-CAB, 3.5mm Mono to 3.5mm Stereo 5v to 12v IR converter cable. This cable is required when using 12v IR products from Xantech, Niles, and SpeakerCraft.
Each ELAN Matrix and HDBaseT receiver is supplied with all necessary IR hardware required and includes:
Infrared (IR) Distribution
IR Control Cable - EL-4KACC-IR-CAB
ELAN IR Control cable 3.5mm Mono to 3.5mm Stereo for linking third party IR Receivers to ELAN Premium, Matrix, and HDBaseT HDMI Series products.
Compatible with 12v IR third party products.
Note: Cable is directional as indicated
IR Receiver - Stereo 3.5mm
Signal
Power
Ground
Infrared 3.5mm Pin-Out
IR Emitter - Mono 3.5mm
Signal
Ground
Page 10
PREMIUM SERIES USER MANUAL
10
www.elanhomesystems.com
Infrared (IR) Control
Remote Control Description
The ELAN Premium Series matrix units are supplied with IR Remote Control for source selection and general setup.
As well as controlling matrix solutions using the original ELAN remote the ELAN products can be controlled using the original Infrared NEC codes shown at the rear of this manual.
OUTPUT AND INPUT SELECTION
A Select the zone OUTPUT you wish to change the source on
(Numbers 1-8 correspond to the zone outputs 1-8).
B Select the source INPUT you wish to change on the selected zone to
(Numbers 1-8 corresponds to the source inputs 1-8)
C Press PTP button If you wish to instantly mirror all inputs and outputs
(Example - Input 1 to output 1, input 2 to output 2 etc).
POWER
1
ALL PTP
OUTPUT
2 3 4
5 6 7 8
1
ALL
INPUT
2 3 4
5 6 7 8
1080i 1080p 3D 4K
USER1 USER2 FN1
EDID
FN2
2.0CH 5.1CH 7.1CH COPY
B
C
A
Page 11
11
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
Example Schematic
EL-4KPM-V66
Cat 5/5e/6
Network Connection
RS232
HDMI
Stereo Audio
IR Cable
EL-4KHDBT-RX-40-IRS
Application Diagram
8X8 MATRIX SHOWN FOR
REFERENCE PURPOSES ONLY
Cat Cable
Page 12
PREMIUM SERIES USER MANUAL
12
www.elanhomesystems.com
Video Input Connections: 6x HDMI Type A, 19-pin, female, 1x HDBaseT RJ45 connector
Video Output Connections: 6x HDMI Type A, 19-pin, female, 6x HDBaseT RJ45 connector
Audio Input Connections: 6x 3.5mm stereo jack (L/R)
Audio Output Connections: 6x RCA (SPDIF), 6x 3.5mm stereo jack (L/ R)
RS-232 serial ports: 7x 3-Pin Phoenix connector
TCP/IP Control: RJ45, female
Ethernet/Network: RJ45, female
IR Input ports: 7x 5v 3.5mm stereo jack
IR Output ports: 7x 5v 3.5mm mono jack
Rack-Mountable: 2U rack height, rack ears included
Casing Dimensions (W x H x D): 440mm x 87mm x 361m, without feet
Dimensions Including Connections (W x H x D): 440mm x 87mm x 369mm, with feet
Shipping Weight: 8.8kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature: -4°F to 140°F (-20°C to 60°C)
Input: 100V-250V, 50Hz-60HZ, 13A
NOTE : Specifications are subject to change without notice. Weight details are approximate and will alter per model.
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
Specifications
Package Contents:
• 1 x EL-4KPM-V66-A1812
• 1 x Remote control
Remote Includes CR2025 battery
• 1 x Rack mounting kit
• 6 x 5v-to-12v IR converter cables
• 2 x Serial cable - 9-pin RS-232 to 3-pin phoenix connector
• 1 x User manual
• 4 x Power cables (Type A, C, G & I)
Page 13
13
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
IR commands
COMMAND NEC HEX
POWER 0X14
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 003f 0015
0015 0015 00 3f 0015 003f 0015 0 03f 0015 05d3
OUTPUT 1 0X09
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015
003f 0 015 003f 0015 003 f 0015 003f 0015 05d 3
OUTPUT 2 0X1d
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015
0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015
0015 0015 00 3f 0015 003f 0015 0 03f 0015 05d3
OUTPUT 3 0X1f
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015
0015 0015 00 15 0015 0 015 0015 0 015 0015 0 015 0015 0015 00 15
0015 0015 0015 0 03f 0015 003f 0 015 003f 0015 05d3
OUTPUT 4 0X0d
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015
003f 0 015 003f 0015 003 f 0015 003f 0015 05d 3
NEC Customer Code = 1898
OUTPUT 5 0X19
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 0015 0015 0015 0015 003f 0015 003f 0015 0015
0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015
0015 0015 00 3f 0015 003f 0015 0 03f 0015 05d3
OUTPUT 6 0X1b
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015
0015 003 f 0015 003f 0015 00 3f 0015 05d3
OUTPUT 7 0X11
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015
0015 003 f 0015 003f 0015 00 3f 0015 05d3
OUTPUT 8 0X15
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 003f 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015
0015 003 f 0015 003f 0015 00 3f 0015 05d3
OUTPUT ALL 0X 17
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016
0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016
0016 003 F 0016 003F 0016 0 03F 0016 0689
OUTPUT PTP 0X12
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016
0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016
0016 003 F 0016 003F 0016 0 03F 0016 0689
Advanced Matrix features are not available via IR commands
COMMAND NEC HEX
INPU T 1 0X50
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015
0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015
0015 0015 00 3f 0015 0015 0015 003f 0 015 05d3
INPU T 2 0X55
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 003f 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015
0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015
0015 0015 00 3f 0015 0015 0015 003f 0 015 05d3
INPU T 3 0X48
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015
0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015 0015
003f 0 015 003f 0015 0015 0015 0 03f 0015 05d3
INPU T 4 0X4a
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015 0015 0015
0015 003f 0015 0015 0015 003f 0015 0015 0015 003f 0015 0015 0015
003f 0 015 003f 0015 0015 0015 0 03f 0015 05d3
INPU T 5 0X5e
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015
0015 003f 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015
0015 0015 00 3f 0015 0015 0015 003f 0 015 05d3
INPU T 6 0X06
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015
0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015
0015 0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 003f 0015
003f 0 015 003f 0015 003 f 0015 003f 0015 05d 3
INPU T 7 0X05
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 003f 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 003f
0015 003 f 0015 003f 0015 00 3f 0015 05d3
INPU T 8 0X03
0000 0069 0000 002a 0150 00a8 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015
0015 0015 0015 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015
0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015
0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f
0015 003 f 0015 003f 0015 00 3f 0015 05d3
INPU T ALL 0X47
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F
0016 003 F 0016 0016 0016 003 F 0016 0689
INPU T DOWN 0X07
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F
0016 003 F 0016 003F 0016 0 03F 0016 0689
INPU T UP 0X40
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 0 016 0016 0 016 0016 0 016 0016 0 016 0016 0 016 0016 0 016 0016
003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F
0016 003 F 0016 0016 0016 003 F 0016 0689
Page 14
PREMIUM SERIES USER MANUAL
14
www.elanhomesystems.com
COMMAND NEC HEX
1080i 0X18
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016
003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016
003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016
0689
1080p 0X44
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016
0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016
0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016
0689
3D 0X0F
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016
0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016
0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016
0689
4K 0X51
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016
003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016
0689
2.0ch Audio 0X0A
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016
0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016
003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016
0689
5.1ch Audio 0X1E
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016
0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016
003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016
0689
7.1ch Audio 0X0E
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F
0016 003 F 0016 003F 0016 0 03F 0016 0689
Copy EDID 0X1A
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016
0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016
0016 003 F 0016 003F 0016 0 03F 0016 0689
User 1 0X53
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016
003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016
0016 003 F 0016 0016 0016 003 F 0016 0689
COMMAND NEC HEX
User 2 0X52
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016
003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016
0016 003 F 0016 0016 0016 003 F 0016 0689
User 3 0X01
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F
0016 003 F 0016 003F 0016 0 03F 0016 0689
User 4 0X45
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016
0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016
0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F
0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016
003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F
0016 003 F 0016 0016 0016 003 F 0016 0689
Page 15
15
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
RS-232 and Telnet Commands
NO. COMAND ACTION
1 ? Print Help Information
2 HELP Print Help Information
3 STATUS Print System Status And Port Status
4 PON Power On, System Run On Normal State
5 POFF Power Off, System Run On Power Save State
6 IR ON/OFF Set System IR Control On Or Off
7 KEY ON/OFF Set System KEY Control On Or Off
8 APM ON/OFF Set Advanced Process Mode On Or Off
9 BEEP ON/OFF Set Onboard Beep On Or Off
10
RESET RESET ALL
Reset System To Default Setting
(Should Type “Yes” To Confirm, “No” To Discard)
Reset System And Network To Default Setting
11
MXIR xx FR yy Output Port IR:xx From Local IR:yy
xx= [00]: All Output IR, [ 01...08]: Output IR yy=[01...08] Local IR
12
MXIR GI (+-) xx Global IR_IN Signal To Input/ Output IR:xx
xx= [01...08]: Input IR, [09...16]: Local IR xx=[17...24]: Output IR +: Add xx To Current Setting
-: Remove xx From Current Setting
13
MXIR GO (+-)xx Global IR_OUT Signal From Input/Output IR:xx
xx= [01...08]: Input IR, [09...16]: Local IR xx= [17...24]: Output IR, [25]: Global IR In +: Add xx To Current Setting
-: Remove xx From Current Setting
14
MXRS-232 xx TO yy Local RS­232:xx Connect To Input/Output RS-232:yy
xx= [01...08]: Local RS-232, [09]: Global RS-232 yy=[00]: Disconnect With Any RS-232 yy=[01...08]: Input RS-232, [09...16 ]: Output RS-232
15 MXSTA Print Matrix IR And RS-232 Connect State
16
AUD OUT xx ANA yy
Output Port:xx Audio From Input Port:yy Stereo
NO. COMAND ACTION
17
AUD OUT xx EXT yy
Output Por t:xx Audio From Input Port:yy Ex tract xx= [00]: All Output Audio, [01...08] : Output Audio yy= [ 01...08]: Input Port Audio
18
AUD OUT xx ARC tt
Output Por t:xx Audio From Output Port:tt ARC xx= [00]: All Output Audio, [01...08] : Output Audio yy= [ 01...08]: Input Port Audio
19
AUD OUT xx FOANA
Output Por t:xx Audio From Select Video Input Stereo xx= [00]: All Output Audio, [01...08] : Output Audio
20
AUD OUT xx FOEXT
Output Por t:xx Audio From Select Video Extract xx= [00]: All Output Audio, [01...08] : Output Audio
21
AUD OUT xx DL zz
Set AUDIO:xx Delay zz ms zz= 00 ~ 500ms Delay, 50ms per Step
22 AUD STA Print Input/Output Port Audio Setting State
23 AUD IN xx ORG
Input Port:x x Use Original Receive HDMI /DVI Signal
23 AUD IN xx BPS Input Port:xx Bypass Receive HDMI/ DVI Signal
24 AUD IN xx ANA Input Port:xx Insert Stereo To HDMI/DVI Signal
25 AUD IN xx AUTO
Input Port:xx Insert Stereo To DVI Signal Only xx= = [00]: All Input Port, [ 01...08]: Input Port
26 IN xx FO yy INPUT:xx Force Select Source:yy, Stop Auto
27 IN xx AU yy
INPUT:xx Auto Detect Source, Source:yy High Priority xx= [00]: All INPUT Port, [ 01...08]: INPUT Port yy=[01]: HDMI, [ 02]: HDBT
28 OUT xx ON/OFF Set OUTPUT:xx On Or Off
29 OUT xx FR yy Set OUTPUT:xx From INPUT:yy
30 OUT xx EH/ET
Set OUTPUT:xx Use HDMI /HDBT EDID xx= [00]: All OUTPUT Port, [01...08]: OUTPUT Port yy=[01...08]: INPUT Port
Page 16
PREMIUM SERIES USER MANUAL
16
www.elanhomesystems.com
COMMAND ACTION
EDID xx CP yy
Set Input:x x EDID Copy From Output :yy
EDID xx DF zz
Set Input:x x EDID To Default ED ID: zz
xx= [00] : All IN PUT Port, [ 01...06]: IN PUT Port
yy= [01...06] : OUTPU T Port
zz= 00: HDMI 108 0p@6 0Hz, Audio 2CH P CM
zz= 01: HDMI 1080p @60Hz, Audio 5.1CH DTS/ DOLBY
zz= 02: HDMI 1080 p@ 60Hz, Audio 7.1CH DTS/DOLB Y/HD
zz= 03: HDMI 1080i@ 60Hz, Audio 2CH PCM
zz= 04: HDMI 1080i@ 60Hz, Audio 5.1CH DTS /DOLBY
zz= 05: HDMI 1080i@ 60Hz, Audio 7.1CH DTS/ DOLBY/HD
zz= 06: HDMI 108 0p@60Hz /3D, A udio 2CH P CM
zz= 07: HDMI 108 0p@6 0Hz /3D, Audio 5.1CH DTS /DO LBY
zz= 08: HDMI 1080p@ 60Hz/ 3D, Audio 7.1CH DTS/ DOLBY/ HD
zz= 09: HDMI 4 K@30Hz 4 :4: 4, Audio 2CH PCM
zz=10: H DMI 4K@3 0Hz 4 :4: 4, Audio 5.1CH DTS /DOLBY
zz=11: HDMI 4 K@ 30Hz 4:4 :4, Audio 7.1CH DTS/ DOLBY/ HD
zz=12: DVI 1280x1024@60Hz, Audio None
zz=13: DV I 1920x108 0@ 60Hz, Audio N one
zz=14: DV I 1920x1200@ 60Hz, Audio None
zz=15: User EDID 1
zz=16: User EDI D 2
zz=17: GUI Download ED ID
zz=18: HDMI 4K @60Hz 4 :2:0, Audio 2CH PC M
zz=19: H DMI 4K@60Hz 4:2:0, Audio 5.1CH DTS/ DOLBY
zz=2 0: HDMI 4K @60Hz 4 :2:0, Audio 7.1CH DTS/ DOLBY/ HD
NET D HCP ON/ OFF : S et Auto I P( DHCP) ON Or O FF
NET IP xxx.xxx.xxx.xxx : Set I P Address
NET GW xxx.xxx.xxx.xxx : Set Gateway Address
NET SM xxx.xxx.xxx.xxx : Set Subnet Mask Address
NET R B : Set Net work Reb oot and Apply New C onfig !! !
NET T N xxxx : Set Telnet Por t
MUT E ON /OF F OUT yy Set Output Audio: yy M ute On or Off
VOL xx O UT yy
Set Output Audio :yy Volume to xx
yy= [00 ]: All Output Audio, [01...06]: Output Audio
xx= [00...30 ]: Volume Value
xx=+: Volume Increase
xx= -: Volume Decrease
Page 17
17
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION - changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
CANADA, INDUSTRY CANADA (IC) NOTICES
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
CANADA, AVIS D’INDUSTRY CANADA (IC)
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Certifications
Page 18
PREMIUM SERIES USER MANUAL
18
www.elanhomesystems.com
Notes
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Page 19
19
contact techsupport@ elanhomesystems.com
PREMIUM SERIES USER MANUAL
Notes
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Page 20
10014818 Rev-C0, 04/2017
main:
1 (800) 472-5555 - US 1 (707) 283-5900 - International 1 (707) 283-5901 - Fax
tech support:
techsupport@elanhomesystems.com
web:
elanhomesystems.com
© 2017 ELAN® is a registered trademark of Core Brands, LLC.
Loading...