How it Works
Elan
Loading...
EL-4KM-V44-KIT
User Manual
20 pgs1.46 Mb0

Elan EL-4KM-V44-KIT User Manual

Download
Page 1
EL-4KM-V44-KIT
User Manual
VideoMatrix
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
EL-4KM-V44
EDID
RS-232
1 2 3 4 1 2 3 4
IR Output
Input
HDMI 1
HDMI 2
HDMI 3 HDMI 4
321 0 0 1
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 1
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 2
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 3
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
RS-232
TCP/IP
24V
IR Ext.
3.5A
VideoMatrix
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
Page 2
EL-4KM-V44-KIT USER MANUAL
02
www.elanhomesystems.com
Introduction 03
Features 03
Panel Descriptions 04
Control Ports 05
HDBaseT Receiver Options 06
Matrix Front Panel Controls 07
Audio Breakout 08
Terminating HDBaseT CAT Cables 09
Understanding Matrix/Receiver Status Lights 09
Infrared Distribution 10
Infrared Remote Control 11
EDID Control 12
Application Diagram 13
Specifications 14
Package Contents 14
Maintenance 14
RS-232 and Telnet Commands 15-16
Infrared Commands 17-18
Web Browser Interface 19
Certifications 19
Contents
Surge protection device recommended
This product contains sensitive electrical components that may be damaged by elec­trical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.
Safety And Performance Notice
The transmission distances of HDMI over UTP cables are measured using TE CONNECTIVITY 1427071-6
EIA/TIA-568-B termination (T568B) of cables is recommended for optimal perfor­mance.
To minimize interference of the unshielded twisted pairs in the CAT5e/6 cable do not run the HDBaseT / Cat5e/6/6a cabling with or in close parallel proximity to mains power cables.
Do not substitute or use any other power supply other than the enclosed unit, or a ELAN approved replacement.
Do not disassemble either the Transmitter or Receiver units for any reason. Doing so will void the manufacturer’s warranty.
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully before con­necting, operating or adjusting this product. Please keep this manual for future reference.
Page 3
03
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
The ELAN 4x4 HDBaseT™ matrix offers unprecedented performance and value for the custom installation market. The EL-4KM-V44 is a 4K 4x4 HDCP 2.2 matrix package, delivering HDMI, bi-directional IR, RS-232, and PoH (PoE) up to lenghts of 40m at 4K (70m @1080p) over a single CAT cable. The matrix also provides advanced features including audio breakout with pre-amp variable line-level control, simultaneous HDBaseT™/HDMI outputs, RS-232 pass through to enable 3rd party control of displays and a web browser interface module for control and configuration of the matrix. The EL-4KM-V44 is supplied with 4 x EL-4KHDBT-RX-40-IRS Receivers.
Introduction
• Features 4x HDMI inputs which can be independently routed to 4x HDBaseT™/HDMI outputs
• Simultaneous HDBaseT™ and HDMI outputs to allow connection to dual displays per zone
• HDMI audio breakout to associated analog L/R audio outputs with pre-amp line level control
• Extends up to distance of 70m 1080P over single CAT cable
• Supports 4K UHD video up to 40m (3840 x 2160 @30Hz 4:4:4, 4096 x 2160 @24Hz 4:4:4, and 4K @60Hz 4:2:0)
• Web browser interface for control and configuration of Matrix
• Supports 3D signal display
• Supports all industry standard video resolutions including VGA-WUXGA and 480i-4K
• Supports all known HDMI audio formats including Dolby TrueHD, Dolby Atmos, Dolby Digital Plus and DTS-HD
Master Audio transmission
• Supports bi-directional IR and RS-232 from all input and HDBaseT output locations
• Supplied with 4x 5v-to-12v IR converter cables (EL-4KACC-IR-CAB)
• Control via front panel, IR, RS-232 and TCP/IP
• HDCP 2.2 compliant
• Supports PoH (Power over HDBaseT™) to power compatible HDBaseT™ receivers
• Advanced EDID management
• Matrix kit is supplied with 4 x EL-4KHDBT-RX-40-IRS HDBaseT™ receivers
• 1U Design for 19” rack mount integration - mounting kit included
• Matrix can be configured using front panel, supplied IR remote, or Web GUI.
Features:
Page 4
EL-4KM-V44-KIT USER MANUAL
04
www.elanhomesystems.com
EL-4KM-V44
EDID
RS-232
1 2 3 4 1 2 3 4
IR Input
IR Output
Input
HDMI 1
HDMI 2
HDMI 3 HDMI 4
321 0 0 1
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 1
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 2
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 3
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
RS-232
TCP/IP
24V
IR Ext.
3.5A
VideoMatrix
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
VideoMatrix
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
Rear Panel
1 2
3 4 5
141210 13119876
1 IR inputs – 3.5mm stereo jack.
Transmits IR to the zone HDBaseT receiver (displays). When using the IRCAB cable (supplied) ensure cable direction is correct.
2 IR outputs – 3.5mm mono jack –
Routed IR from HDBaseT extender (zone output).
3 Zone outputs 1-4 (please see
descriptions 8-12 for further details).
4 TCP/IP ( RJ45) – Connect to LAN for
TCP/IP & web browser interface control of EL-4KM-V44 Matrix.
5 RS-232 port – For control of the Matrix
switcher from PC or ELAN control processer.
6 EDID DIP switch – Used for global EDID
settings.
7 HDMI inputs – Connect to HDMI
sources.
8 HDBT output – Connect to HDBaseT
receivers.
9 HDMI output – Connect to HDMI display.
Works simultaneously with HDBaseT
output.
q Zone specific bi-directional RS-232
ports – Connect to third party control
device to extend RS-232 commands to
HDBaseT receivers RS-232 port.
w Coaxial digital audio output – Extracted
audio will be concurrent with the corresponding HDMI video output.
e L/R pre-amp variable line level analog
audio output – 3.5mm stereo jack. Extracted audio will be concurrent with the corresponding HDMI video output. Please note: input must be PCM 2ch audio as Matrix does not down-mix
5.1ch audio signals.
r IR input for matrix control – For hard
wired IR connection. Connect to EL AN control processor.
t Power port – Use supplied 24V 3.5A DC
adaptor to power Matrix.
Front Panel
1
2 3 4 5 6 7 8 9
16151413121110
1 LCD display – Shows the status of input/
output selection, EDID etc.
2 IR receiver window.
3 Power LED indicator.
4 Power button – Press to power on/off
the Matrix.
5 HDMI output selection button 1 to 4 –
To select the output from 1 to 4.
6 All button for HDMI outputs – All outputs
will work as one (Selects all outputs).
7 Menu button – Press to enter EDID set
mode (see page 5).
8 Up selection button - Press to change
segment’s value.
9 ESC – Press to quit EDID set mode.
q Lock indicator.
w Lock button – Press to lock the buttons
of the front panel.
e HDMI input selection button 1 to 4 –
Press to select the input from 1 to 4.
r PTP button – Press to mirror all inputs
and outputs (e.g. output 1 to input 1, output 2 to input 2).
t Selection button – Press to select
current setting.
y Down selection button – Press to
change segment’s value.
u Enter button – Press to set EDID to
specified INPUT or copy EDID from specified OUTPUT to specified INPUT.
Panel Descriptions
Page 5
05
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
EL-4KM-V44
RS-232
1 2 3 4 1 2 3 4
IR Input
IR Output
Input
HDMI 1
HDMI 2
HDMI 3 HDMI 4
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 1
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 2
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 3
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
RS-232
TCP/IP
24V
IR Ext.
3.5A
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
EL-4KM-V44
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
RS-232
TCP/IP
24V
IR Ext.
3.5A
3
4
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
The EL-4KM-V44 main communication ports are located on the rear panel and includes the following connections:-
Connections:
A. Global IR Input 3.5mm stereo jack - For control of the Matrix
B. TCP/IP – For control of the Matrix (RJ45 Connector)
C. RS-232 – For control of the Matrix (9 pin serial connection)
D. IR Input (3.5mm stereo jack) for IR pass-through to the associated output
HDBaseT Receiver
E. IR Output (3.5mm mono jack) for routed IR control of source equipment
F. RS-232 (3-pin Phoenix connector) for 2-way RS-232 pass-through to the
associated output HDBaseT Receiver
TCP/IP
The ELAN EL-4KM-V44 Matrix can be controlled via TCP/IP.
For the full list of protocols please see ‘RS-232 and Telenet commands’ located at the rear of this manual.
The EL-4KM-V44 Matrix features a built-in web browser user interface allowing control and configuration of the matrix. For further details please see page 19 ‘Web Browser Interface’.
A ‘Straight-through’ RJ45 patch lead should be used
RS-232 2-Way
The ELAN 4KM-V44 can be controlled via a 9-pin serial cable.
For the full list of protocols please see ‘RS-232 and Telenet commands’ located at the rear of this manual.
Details of RS-232 pin assignment and communication are adjacent. Please note that depending on your control device serial port pin configuration you may require either a ‘Straight’ RS-232 cable or ‘Null-modem’ type.
Control Ports
ELAN RS-232 REMOTE CONTROL
CONSOLE
PIN Assignment PIN Assignment
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 57600 bps
Data Bit: 8-bit
Parity: None
Stop Bit: 1-bit
Flow Control: None
A B
FD E
C
Page 6
EL-4KM-V44-KIT USER MANUAL
06
www.elanhomesystems.com
1 HDBaseT input
2 12V DC power (not required)
3 2-way RS232 (9-pin serial)
4 HDMI output
5 IR Input 3.5mm stereo jack
6 IR Output 3.5mm mono jack
The EL-4KM-V44 Matrix is supplied with 4x EL-4KHDBT-RX-40-IRS HDBaseT receivers
The EL-4KHDBT-RX-40-IRS Receiver is a Class B HDBaseT Receiver with 2-way IR and bi-directional RS-232 pass-through. The Receiver supports display distances up to 70m @ 1080P and 40m 4K (30Hz 4:4:4 & 60Hz 4:2:0).
HDBaseT Receiver Options
The EL-4KM-V44 is also compatible with the EL-4KHDBT-RX-40-IR HDBaseT Receiver. Note: The EL-4KHDBT-RX-40-IR does not support the RS-232 feature on the EL-4KM-V44.
EL-4KHDBT-RX-40-IRS
HDBT In
Standard
Upgrade
LINK POWER
12V 2A
HDMI Out
HDMI LINK
RS-232
IR RX IR TX
EL-4KHDBT-RX-40-IRS
HDBT In
Standard
Upgrade
LINK POWER
12V
2A
1 2
4 5 63
EL-4KHDBT-RX-40-IR
Basic HDBaset Receiver with 2-way IR pass-through. Supports display distances up to 70m @ 1080P and 40m 4K (30Hz 4:4:4 & 60Hz 4:2:0).
Compatible with all ELAN Matrix products.
HDMI Out
LINK
POWER
IR RX IR TX
12V
2A
EL-4KHDBT-RX-40-IR
HDBT In
LINK
HDMI Out
LINK
POWER
IR RX IR TX
12V
2A
HDBaseT input
HDMI Output
IR Output 3.5mm Mono jack
IR Input 3.5mm Stereo jack
12V DC power (not required)
1
2
3
4
5
4 532
1
Page 7
07
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
Matrix Front Panel Controls
Front Panel Display - Input/Output selection
The following display shows current source input selection per zone output.
1. To change input selection first press ‘OUTPUT’ button (1-4)
2. Press desired ‘INPUT’ button (1-4)
3. An ‘X’ indicates that the zone output has been turned off.
Zones can be turned on/off using RS-232/TCP/IP commands.
Zone outputs can be forced back on by powering OFF/ON the matrix. All outputs will be turned on when powered up.
Zone outputs can be forced back on by pressing and holding ‘OUTPUT 1’ button on the front panel for 10 seconds.
The matrix will reset and all outputs will be turned back on.
EDID: IN ALL HDMI: 1080P 2CH
EDID Management - Global or individual input settings
The following characters show adjusting the EDID for ‘All’ inputs (Global). Current EDID value is set to 1080P & 2ch audio.
To change the input signal type using the Matrix front panel buttons press the following:-
Using Matrix Front Panel Buttons
A. Press MENU button
B. Panel will display ‘EDID settings’. Press SELECT button
C. Select the input you wish to fix the EDID on (1-8) or select ‘All’. Use UP/ DOWN buttons to toggle selection and SE LECT button to confirm
D. Select video resolution required (4K, 1080p, 3D etc). Use U P /DOWN buttons to toggle selection and SELE CT button to confirm
E. Select audio resolution required (2CH, 5.1 or 7.1). Use UP/ DOWN buttons to toggle selection and SE LECT button to confirm
F. Press the ESC button to exit
OUT 1 2 x 4 IN 1 2 3 4
2
1
3
4
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
B
A E
C/D
C/D
Page 8
EL-4KM-V44-KIT USER MANUAL
08
www.elanhomesystems.com
Audio Breakout
The EL-4KM-V44 Matrix includes audio breakout from the selected HDMI input to associated analog L/R audio and coaxial digital outputs. Extracted audio will be concurrent with the corresponding HDMI video output.
The EL-4KM-V44 analog outputs include pre-amp line level control allowing you to connect the ELAN matrix directly into a power amplifier for all your multi-room audio needs.
Control of the pre-amp line level outputs is via RS-232, TCP/IP or using the in-built web browser interface. Please see ‘RS-232 & Telnet Commands’ on page 15 for further details.
Note: Volume control is only available on the analog audio outputs. Source input must be PCM 2ch audio for analog audio outputs to work. The EL-4KM-V44 Matrix does not down-mix 5.1ch audio signals.
Volume control of audio outputs is not possible via Infrared control.
1. Coaxial digital output - Output 1
2. Analog pre-amp line level output 3.5mm stereo jack - Output 2
EL-4KM-V44
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 1
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 2
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 3
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
RS-232
TCP/IP
24V
IR Ext.
3.5A
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
PTP
Menu Up
Esc
Select Down Enter
EDID
1
2
Page 9
09
EL-4KM-V44-KIT USER MANUAL
contact techsupport@elanhomesystems.com
Terminating HDBaseT CAT cable
It is important that the interconnecting CAT cable between the ELAN HDBaseT products is terminated using the correct RJ45 pin configuration. The link CAT cable MUST be a ‘straight’ (pin-to-pin) CAT cable and it is advised that this is wired to the T568B wiring standard as this format is less prone to EMI (Electro-Magnetic Interference).
When installing CAT cables it is advised that you use the best possible CAT cable quality possible. HDMI disitrbution products will only work if used with CAT5e standard cable or above. ELAN recommends using a CAT6 cable for your installations, especially when running over longer distances, in areas of high EMI, or with 4K signal distribution.
RJ45 Pin-Out T568B
Understanding the Matrix / Receiver status lights
The ELAN Matrix and HDBaseT extender solutions include status LED indicators on both the Matrix and Receiver products to show all connections are active and to help diagnose possible problems.
Understanding the status lights:-
ELAN Matrix:
• The Yellow HDBaseT status link light will be off when the zone output has been turned off or there is a problem with the specific Matrix output.
• The Yellow HDBaseT status link light will blink when the zone output is on and working
• The Green HDBaseT link light will blink if there is an unstable connection between the ELAN Matrix and HDBaseT Receiver
• The Green HDBaseT link light will be lit when a there is an active HDBaseT Receiver connected to the Matrix
• The Green HDBaseT link light will be off when a there is no connection with a HDBaseT receiver
ELAN HDBaseT Receiver:
• The HDMI link light will be off when there is no connection with a display
• The HDMI link light will be on when there is an active connection with a display (NOTE - Not all HDBaseT RX feature a HDMI status LED)
• The HDBaseT link light will be off when there is no CAT cable/active HDBaseT connection on the RJ45 HDBaseT input
• The HDBaseT link light will blink if there is an unstable connection between the ELAN Matrx and HDBaseT receiver
• The HDBaseT link light will be lit when a CAT cable is connected to the HDBaseT RJ45 output on the Matrix and an active connection is
achieved with the ELAN HDBaseT Receiver.
12345678
Page 10
EL-4KM-V44-KIT USER MANUAL
10
www.elanhomesystems.com
The ELAN range of HDMI matrix products include multiple options for control and routing of IR.
IMPORTANT: The ELAN HDMI Platinum, Matrix, & HDBaseT product lines utilize 5 volts to power an IR Receiver on the IR Input and include an EL-4KACC-IR-CAB, 3.5mm Mono to 3.5mm Stereo 5v to 12v IR converter cable. This cable is required when using 12v IR products from Xantech, Niles, and SpeakerCraft.
Each ELAN Matrix and HDBaseT receiver is supplied with all necessary IR hardware required and includes:
Infrared Distribution
IR Control Cable - EL-4KACC-IR-CAB
ELAN IR Control cable 3.5mm Mono to 3.5mm Stereo for linking third party IR Receivers to ELAN Platinum, Matrix, and HDBaseT HDMI Series products.
Compatible with 12v IR third party products.
Note: Cable is directional as indicated
IR Receiver - Stereo 3.5mm
Signal
Power
Ground
Infrared 3.5mm Pin-Out
IR Emitter - Mono 3.5mm
Signal
Ground
Page 11
11
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
Infrared Remote Control
OUTPUT AND INPUT SELECTION
A. Selects the zone OUTPUT you wish to
change the source on (Numbers 1 - 4 correspond to the zone outputs 1 - 4)
B. Selects the source INPUT you wish to
change on the selected zone (Numbers 1
- 4 correspond to the source inputs 1 - 4)
EXAMPLE
To switch source 2 to zone 4 you would press 4 in the output section (A) followed by press­ing 2 in the Input section (B).
ALL button: The all button selects all the
inputs or outputs in its corresponding box. Example: (The “All” button in the Output box selects all the zones so all zones will change to what source input is selected next)
PTP: This button will align all the zone
outputs with the like numbered source inputs. Example: Input 1 to output 1, input 2 to output 2, etc
EDID SET UP
The EL-4KM-V44 provides a comprehensive range of EDID settings. Below are three examples of how to deploy the desired EDID setting when using the supplied remote.
A. Fix EDID to an Input or ALL inputs:
Press the desired video resolution button (1080I / 1080P / 3D / 4K), then select the desired audio format (2.0CH / 5.1CH / 7.1CH), then select the source input you want this EDID information allocated to by pressing the INPUT 1 – 4 or the ALL button
B. Copy EDID of Output-X to an Input or
ALL: Press the COPY but-ton then select
the OUTPUT you wish to copy the EDID information from, then select the source input you want to copy this EDID to by se­lecting the INPUT 1-4 or the ALL button.
C. User defined EDID to an Input or ALL
inputs: Press USER1 / USER2 button
then select the source you wish to assign this EDID to by select-ing INPUT 1-4 or the ALL button
POWER
1
ALL PTP
OUTPUT
2 3 4
1
ALL
INPUT
2 3 4
POWER
1
ALL PTP
OUTPUT
2 3 4
5 6 7 8
1
ALL
INPUT
2 3 4
5 6 7 8
1080i 1080p 3D 4K
USER1 USER2 FN1
EDID
FN2
2.0CH 5.1CH 7.1CH COPY
1080i 1080p 3D 4K
USER1 USER2 FN1
EDID
FN2
2.0CH 5.1CH 7.1CH COPY
EDID
B
A
NOTE: THE BUTTON PRESS SEQUENCE SHOULD BE FINISHED IN 5 SECONDS,
OTHERWISE THE OPERATION IS DISCARDED
Page 12
EL-4KM-V44-KIT USER MANUAL
12
www.elanhomesystems.com
EDID
RS-232
1
2 3 4 1 2 3 4
IR Input
IR Output
Input
HDMI 1
HDMI 2
HDMI 3 HDMI 4
32 1 0 0 1
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 1
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 2
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 3
RS-232
TxRx
POH
Coaxial
L/R
HDBT
HDMI
Output 4
VideoMatrix
IR Power
Lock
In
Out
1 2
3
4
1 2
3
4 All
EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by the source to find out what audio and video resolutions are supported by the display then from this information the source will discover what the best audio and video resolutions need to be outputted.
While the objective of EDID is to make connecting a digital display to a source a simple plug and play procedure issues do arise when multiple displays or video matrix switching is introduced because of the increased number of variables.
By pre-determining the video resolution and audio format of the source and display device you can reduce the time need for EDID hand shaking thus making switching quicker and more reliable.
Configuration of the EDID settings can be achieved in one of four ways:
1 Via the Web GUI
2 Using Matrix Front Panel Buttons ( For further details see page 7)
3 Using Supplied ELAN Matrix IR Remote Control (For further details see page 10)
4 Using dip-switches on the rear panel of the EL-4KM-V44 Matrix. Please see below table for global EDID settings.
*Note - Once dip-switch settings have been made the EL-4KM-V44 must be power cycled
for settings to be applied.
EDID Control
Global EDID settings
DIP ON ▼/OFF▼ SWITCHING POSITIONS
EDID TYPE3 2 1 0
OFF OFF OFF OFF 1080p/2.0CH
OFF OFF OFF ON 1080p/5.1CH
OFF OFF ON OFF 1080p/7.1CH
OFF OFF ON ON 1080i/2.0CH
OFF ON OFF OFF 1080i/5.1CH
OFF ON OFF ON 1080i/7.1CH
OFF ON ON OFF 4K60Hz 4:2:0/2.0CH
OFF ON ON ON 4K60Hz 4:2:0/5.1CH
ON OFF OFF OFF 4K60Hz 4:2:0/7.1CH
ON OFF OFF ON 4K30Hz 4:4:4/2.0CH
ON OFF ON OFF 4K30Hz 4:4:4/5.1CH
ON OFF ON ON 4K30Hz 4:4:4/7.1CH
ON ON OFF OFF DVI 1280x1024
ON ON OFF ON DVI 1920x1080
ON ON ON OFF DVI 1920x1200
ON ON ON ON Copy Display EDID
Dip-switch position ‘0’ = Off
Dip-switch position ‘1’ = On
Page 13
13
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
Application Diagram
EL-4KM-V44
ZONE
01
ZONE 01
SOURCE 01
SOURCE 02
SOURCE 03
SOURCE 04
ZONE
02
ZONE
03
ZONE
04
ZONE
01
ZONE
02
ZONE
03
ZONE
04
Audio Output Link to HDMI Zone Outputs
IR Receiver
Link to control device
Cat 5/5e/6
Network Connection
RS232
HDMI
Stereo Audio
IR Cable
Control Processor
ZONE 02
ZONE 03
ZONE 04
IR Emitter
Link to source
1 2 3 4
EL-4KHDBT-RX-40-IR
DISPLAY 2
HDBT RECEIVER
in
out
70m max
12V POH
HDMI
RS232
IR
A B
C
D
A
B
C
D
Receiver
MAXIMUM OF 4 SOURCES
DISPLAY 1
EL-4KM-V44
Cat Cable
Page 14
EL-4KM-V44-KIT USER MANUAL
14
www.elanhomesystems.com
Specifications
Video Input Connections: 4x HDMI Type A, 19-pin, female
Video Output Connections: 4x HDMI Type A, 19-pin, female, 4x HDBaseT RJ45 connector
Audio Output Connections: 4x 3.5mm stereo jack
RS-232 serial port: 1x DB-9, female, 4x 3 pin Phoenix
TCP/IP Control: 1x RJ45, female
IR Input ports: 5x5v 3.5mm stereo jack
IR Output ports: 4x5v 3.5mm mono jack
Rack-Mountable: 1U rack height, rack ears included
Casing Dimensions (W x H x D): 440mm x 235mm x 43mm, without feet
Dimensions (W x D x H): 440mm x 241mm x 43mm, with feet
Shipping Weight: 2.7kg
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Storage Temperature: -4°F to 140°F (-20°C to 60°C)
Power Supply: 1x 24V/3.5A DC (POH)
Package Contents:
• 1 x EL-4KM-V44
• 4 x EL-4KHDBT-RX-40-IRS
• 1 x Rack mounting kit
• 4 x Mounting kits
• 1 x 24V/3.5A power supply
• 1 x Remote control
Remote Includes CR2025 battery
• 4 x 5v-to-12v IR converter cables
• 1 x User manual
• 4 x Power cables (Type A, C, G & I)
Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
Page 15
15
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
RS232 and Telnet Commands
The ELAN EL-4KM-V44 can be controlled via serial and TCP/IP. The following pages list all available serial commands for the EL-4KM-V44 Matrix. Details of RS232 pin assignment can be found on page 05.
Commonly used Serial commands:
There are several commands that are commonly used for control and testing:-
STATUS Status will give feedback on Matrix such as zones on, type of connection etc
PON Power on
POFF Power off
OUTxxON (xx is the zone number you wish to turn on)
Example:- OUT01ON (This would turn output one back on)
OU Tx xFRyy (xx is the zone out, yy is the input)
Example:- OUT01FR04 ( This would switch output 1 to source input 4)
Common Mistakes
• Carriage return – Some programs do not require the carriage return where as other will not work unless sent directly after the string. In the case of some Terminal software the token <CR> is used to execute a carriage return. Depending on the program you are using this token maybe different. Some other examples that other control systems deploy include \r or 0D (in hex)
• Spaces – ELAN commands do not require space between commands unless specified. There may be some programs that require spacing in order to work.
- How the string should look is as follows OUT01ON
- How the string may look if spaces are required: OUT{ Space}01{Space}ON
• Baud rate or other serial protocol settings not correct - please see Page 5 for Matrix settings
RS232 Command Description
? Print Help Information
HELP Print Help Information
STATUS Print System Status And Port Status
PON Power On, System Run On Normal State
POFF Power Off, System Run On Power Save State
IR ON/OFF Set System IR Control On Or Off
KEYON/OFF Set System KEY Control On Or Off
DBG ON/OFF Set Debug Mode On Or Off
BEEPON/OFF Set Onboard Beep On Or Off
RESET RESET ALL
Reset System To Default Setting (Should Type “Yes” To Confirm, “No” To Discard) Reset System And Network To Default Setting
OUT xxON/OFF Set OUTPUT:xx On Or Off
POH xxON/OFF Set POH OUTPUT:xx On Or Off (xx = 01 to 04 or 'ALL' for all outputs)
Page 16
EL-4KM-V44-KIT USER MANUAL
16
www.elanhomesystems.com
RS232 and Telnet Commands (Continued)
RS232 Command Description
OUT xx FR yy Set OUTPUT:xx From INPUT:yy
EDID xx CPyy
Copy EDID from output (yy) to input (xx)
Both yy & xx can be set individually (01-08) or as ALL (00)
Set Input:xx EDID To Default EDID:zz xx=00: Select All INPUT Port xx=[01...04]: Select One INPUT Port yy=[01...04]: Select One OUTPUT Port zz=00: HDMI 1080p@60Hz, Audio 2CH PCM zz=01: HDMI 1080p@60Hz, Audio 5.1CH DTS/DOLBY zz=02: HDMI 1080p@60Hz, Audio 7.1CH DTS/DOLBY/HD zz=03: HDMI 1080i@60Hz, Audio 2CH PCM zz=04: HDMI 1080i@60Hz, Audio 5.1CH DTS/DOLBY zz=05: HDMI 1080i@60Hz, Audio 7.1CH DTS/DOLBY/HD zz=06: HDMI 1080p@60Hz/3D, Audio 2CH PCM zz=07: HDMI 1080p@60Hz/3D, Audio 5.1CH DTS/DOLBY zz=08: HDMI 1080p@60Hz/3D, Audio 7.1CH DTS/DOLBY/HD zz=09: HDMI 4K@30Hz 4:4:4, Audio 2CH PCM zz=10: HDMI 4K@30Hz 4:4:4, Audio 5.1CH DTS/DOLBY zz=11: HDMI 4K@30Hz 4:4:4, Audio 7.1CH DTS/DOLBY/HD zz=12: DVI 1280x1024@60Hz, Audio None zz=13: DVI 1920x1080@60Hz, Audio None zz=14: DVI 1920x1200@60Hz, Audio None zz=15: User EDID 1 zz=16: User EDID 2 zz=17: GUI Download EDID zz=18: HDMI 4K@60Hz 4:2:0, Audio 2CH PCM zz=19: HDMI 4K@60Hz 4:2:0, Audio 5.1CH DTS/DOLBY zz=20: HDMI 4K@60Hz 4:2:0, Audio 7.1CH DTS/DOLBY/HD
EDIDxx DF zz
MUTE mm OUT yy Turn MUTE (mm = ON or OFF) on OUTPUT (yy = 01 to 04 or 00 for all outputs)
Set VOLUME level:xx on OUTPUT:yy
xx = 00…30: Set volume levels
VOLxx OUT yy xx = +: Volume level increases
xx = -: Volume level decreases
yy = 00: Select ALL output ports
xx = 01 to 04: Select single output port
NET DHCP ON/OFF : Set Auto IP(DHCP) ON Or OFF NET IP xxx.xxx.xxx.xxx : Set IP Address NET GW xxx.xxx.xxx.xxx : Set Gateway Address NET SM xxx.xxx.xxx.xxx : Set Subnet Mask Address NET RB : Set Network Reboot and Apply New Config!!! NET TN xxxx : Set Telnet Port
Page 17
17
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
Infrared Commands
4X4 MATRIX PRODUCTS NEC IR: CUSTOMER CODE 1898 HEX IR
POWER 14
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
OUTPUT 1 09
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
OUTPUT 2 1D
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
OUTPUT 3 1F
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003f 0016 003f 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003f 0016 003f 0016 0016 0016 0016 0016 003f 0016 003f 0016 003f 0016 003f 0016 003f 0016 003f 0 016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003f 0016 003f 0016 003f 0 016 0689
OUTPUT 4 0D
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
OUTPUT ALL 19
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
OUTPUT PTP 18
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
INPU T 1 50
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
INPU T 2 55
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
INPU T 3 48
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0689
INPU T 4 4A
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0689
INPU T ALL 5E
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
INPUT BACK 06
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
Page 18
EL-4KM-V44-KIT USER MANUAL
18
www.elanhomesystems.com
Infrared Commands
INPU T UP 05
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
1080i 18
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
1080P 44
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0689
3D 0F
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
4K 51
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
2.0CH 0A
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
5.1CH 1E
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
7.1C H 0E
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
COPY 1A
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0689
USER 1 53
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
USER 2 52
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 003F 0016 0689
USER 3 01
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 003F 0016 0689
USER 4 45
0000 006D 0000 0022 0157 00AC 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 0016 0016 003F 0016 003F 0016 0016 0016 003F 0016 0016 0016 0016 0016 0016 0016 003F 0016 0016 0016 0016 0016 003F 0016 0016 0016 003F 0016 003F 0016 003F 0016 0016 0016 003F 0016 0689
Page 19
19
contact techsupport@ elanhomesystems.com
EL-4KM-V44-KIT USER MANUAL
Web Browser Interface
The ELAN EL-4KM-V44 matrix unit can be both controlled and configured using the in-built web-server.
The EL-4KM-V44 Matrix must be connected to an active network router/switch and it is advised that the Matrix is given a static IP address. You can configure the network settings of the Matrix using the Web Browser Interface ( ELAN Matrix products are shipped with the network set to DHCP)
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi­cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer­ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution - changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Canada, avis d’Industry Canada (IC)
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of mate­rial resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
Certifications
Page 20
10014815 Rev-C0, 04/2017
main:
1 (800) 472-5555 - US 1 (707) 283-5900 - International 1 (707) 283-5901 - Fax
tech support:
techsupport@elanhomesystems.com
web:
elanhomesystems.com
© 2017 ELAN® is a registered trademark of Core Brands, LLC.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use