Elabs HM1CK-3 Instruction Manual
HDMI UTP
Extender Series
H M1CK-3
CE labs can support many areas of your audio and video distribution needs.
Warning : Using a mono connector will damage the UNIT.
We manufacture:
• Digital Signage software and Media Players
• HD Matrix Switchers
• RF amplifiers
• HDMI and Component HD distribution amplifiers
• CAT 5 Signal Extenders
• VGA Extenders and Splitters
• and cables of all types.
See our full product line at
www.celabs.net
WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in material
and workmanship, under normal use and service, for a period of one year from
the purchase by the original purchaser. If this product is defective or
malfunctions, Cable Electronics Inc. will replace or repair this unit (at their
option) within a reasonable time. No expressed or implied warranty is made
for any defects caused by immersion or exposure to liquids, abuse, neglect,
improper operation of unit, excess wear and tear, act of nature, including, but
not limted to, fire, flood or lightning, and defects resulting from unauthorized
disassembly and or modification.
Document: HM1CK-3_manual.pdf
930-5065-01_ Rev.B00
3209 Wood Drive
Garland, TX 75041
Phone: (469) 429-9200
Toll free: (800) 767-6189
Fax: (469) 429-9205
www.celabs.net
Key Features:
• Uses only one CAT5e/6/6a/7 cable
Pin Out for the IR:
• HDMI™ 1.3 and HDCP compliant
• 3D ready
• Extend signal up to 328ft(CAT5e and CAT6a/7) at
1080p/60Hz/48 bit
• Bi-Directional control signal RS-232 allowing status request and
control of the destination unit
•
Bi-Directional IR control signal (30 - 60 KHz maximum)
• Uncompressed high definition video up to 1080p/60Hz/48bits
• Maximum data rate 3.4 Gbps
• Audio transmission supports Dolby TrueHD, DTS-HD MA
•
No adjustment required
™
LAUNAM NOITCURTSNI
EMITTER(Blaster)
1. Signal Output
2. + 5.6V
3. GND
RECEIVER
1. Signal Input
2. + 5.6V
3. GND
•
4K x 2K Supported
A
PANEL VIEW
Transmitter
Receiver
CABLE
CE labs recommendation: TIA/EIA-568-B. High quality CAT 5e, CAT6, CAT6a, and
CAT7 UTP (Unshielded Twisted Pair )/STP (Shielded Twisted Pair ) or FTP (Foiled
Twisted Pair) cables.
RJ45 Define: Video Link (TIA/EIA-568-B)
1. Orange/White Data0 +
2. Orange Data0 -
3. Green/White Data1 +
4. Blue Data2 +
5. Blue/White Data2 -
6. Green Data1 -
7. Brown/White Data3 +
8. Brown Data3 -
TRANSMISSION DISTANCE
The maximum tarnsmission distance is up to 328 ft, lower resolutions will not
allow longer distances.
Cable length should be less than 5 meters (15 ft) between the HM1CK and
wall jack.
Max 328 ft
Max 5M Max 5M
Transmitter
Power Power
Wall Jack Wall Jack Receiver
INSTALLATION VIEW
LED INDICATION
Green Power
Blue IR Reveive
Red IR Transmit
RJ-45 Green Link
CAUTION
• Cable length must be less that 15 ft between HDMI extender and wall
• DO NOT connect the transmitter or receiver to an AC source shared with a
motor device
• There must be a power supply to both the transmitter and receiver
connectors (RJ45 jacks).
• CAT5e/6/6a/7 cable must be away from any device, wire, cable, etc. that
generate EMI (electromagnetic interference).
Examples: Microwave, cellular phones, radio equipment, fluorescent lamps,
high-voltage power lines.
• DO NOT USE regular CAT5 cable. It does not have enough bandwidth.
• DO NOT connect to any network.
• DO NOT USE stranded cable.
• DO NOT place the IR emitter and IR pickup facing each other. This could
cause interference.
Transmitter
Receiver
Resolution
4K x 2K/1080P/60Hz/48 bit
Distance 328 ft/100M (max)
HDMI Connector Type A
RS-232 Baud Rate Up to 115200 bps/Full Duplex
RS-232 Connector DB9 Female DB9 Male
IR Carrier
30 - 60Khz/±10°/30 ft max
Power Supply Regulated 5V/2Amp
Power Consumption 600mA (Max) 1200mA (Max)
Temperature Operation: 0 to 55°C, Storage: -20 to 85°C
Humidity Up to 95%
Dimensions 5 1/8” x 3 1/2” x 1 1/8”
Weight 10 oz. 10 oz.
HDMI output
HDMI source
transmitter
receiver
328 ft
CAT5e/6/6a/7
Cable
HDMI display
HDMI input
SPECIFICATIONS
Loading...