EKWB EK-FB ASUS ROG ZE Monoblock Service Manual
All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017
REMOVING STOCK COOLER. Remove all encircled screws. There are 4 (four) screws
on the back of the motherboard that need to be removed in order to remove the
factory installed MOSFET heat pipe cooling solution. And 3 (three) screws for the
plastic factory I/O cover. Please store away the factory backplate and I/O cover as
it will be reused.
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual thoroughly before beginning with the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of ASUS ZENITH EXTREME motherboard
BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.
STEP 2: PREPARING YOUR MOTHERBOARD
STEP 3: PREPARING YOUR MOTHERBOARD
APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader
(IHS) - see sample photo below with enclosed thermal grease.
The quantity of about two stripes is just about right. There is no need to cover the
whole IHS. Applying too much thermal grease will have negative impact on the cooling
performance!
STEP 4: CUTTING THERMAL PADS
Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:
DIMENSIONS ON PICTURES BELOW ARE SCALED.
Replacement thermal pads @ EKWB web shop:
Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]
Installation manual for EK-FB ASUS ROG ZE Monoblock water block
Mosfets
CPU socket
AMD X399
Chipset
1. Thermal pad G– 1.0mm
(for mosfets and inductor coils):
All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.0. Published on October 10th 2017
Place thermal pads on PCB as shown on the picture below.
PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL
PADS PRIOR TO INSTALLATION!
STEP 5: PLACING THERMAL PADS
STEP 6: PLACING A BLOCK ON TO THE MOTHERBOARD
Place the EK-FB ASUS ROG ZE Monoblock series water block gently to the motherboard
or vice versa (as shown on photo below). Make sure that mounting holes are aligned.
Place it on factory installed washers on the motherboard (MOSFET area).
STEP 7.1: ATTACHING A BLOCK ON TO THE MOTHERBOARD
STEP 7.2: ATTACHING A BLOCK ON TO THE MOTHERBOARD
Prior to fastening the screws please make sure the mounting holes on the
motherboard’s circuit board are aligned with the water block. Secure top 4 (four)
nickel screws with enclosed 2,5mm Allen key. Tighten screws diagonally and evenly
till the end of the thread. Do not use excessive force when tightening the screws!
Prior to fastening the screws please make sure the mounting holes on the
motherboard’s circuit board are aligned with the water block. Use 2 (two) M2,5x7 AX1
screws with original backplate. Tighten the screws evenly. Do not use excessive force
when tightening the screws! Now you can reinstall factory plastic I/O cover.
STEP 8: CONNECTING THE D-RGB LED STRIP (optional)
Plug the 4-pin connector from Monoblock D-RGB LED strip to the ADD HEADER on
the motherboard. Please ensure that the arrow indicated on the connector is plugged
into the +5V line as indicated on your motherboard. Failure to do so will damage
your motherboard or LED strip.
For the EK-FB ASUS ROG ZE Monoblock series water block to operate properly the
G1/4 port nearest to the right edge of the water block MUST BE USED AS THE INLET
PORT. EK recommends the use of EK-ACF fittings. When using fittings other than EKACF series please use hose clamps or appropriate substitute to secure the tubing to
the barb. The use of biocide containing and corrosion inhibiting coolant is always
recommended for any liquid cooling system.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver Allen key
M2.5x7 screws
Tubing
IMPORTANT: USE
THIS OPENING AS
AN INLET PORT!
Place 1mm thermal pads in
large strip over marked area
and make sure all mosfet chips
and inductor coils are covered.
Loading...