Ekofires SE2015 Installation & User's Instructions

INSTALLATION & USER INSTRUCTIONS

All instructions must be handed to the user for

safekeeping.

Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not per­mitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.

1

Revision F - 02/16

© 2016 Focal Point Fires plc.

GB IE

WALL MOUNTED LCD ELECTRIC FIRE

MODELS COVERED BY THESE INSTRUCTIONS

1040 LCD ELECTRIC
SE2015

Figure 1 : eko 1 040

Christchurch, Dorset BH23 2BT

Tel: [phone]
Fax: [phone]
www.ekofires.co.uk

e-mail: [e-mail]

The Evoke Electric Wall Heater provides convected heating in conjunction with an LCD screen which can display a number of different fuel
effects and scenes. The appliance is designed for indoor use, and can be simply wall mounted in the majority of wall positions anticipated. It can
be located in any household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future
reference and pass on as necessary to subsequent owners of the appliance.

1.0 PRELIMINARY NOTES

I N S TA L L AT I O N & U S E R I N S T RU C T I O N S

2

GB IE

© 2016 Focal Point Fires plc.

Section Contents Page No.

1.0 Preliminary Notes 2

2.0 Appliance Data 3

3.0 Electrical Installation Requirements 3

4.0 Site Requirements 3

5.0 Clearances to Combustible Materials 3

6.0 Unpacking the Appliance 4

7.0 Component Checklist 4

Section Contents Page No.

8.0 Fixing the Appliance 4

9.0 Operating the Appliance 5

10.0 Safety Cut-Out System 6

11.0 Cleaning and Maintenance 6

12.0 Servicing 6

13.0 Appliance Dimensions 7

14.0 Guarantee - Terms and Conditions 7

IMPORTANT - THESE INSTRUCTIONS SHOULD BE READ CAREFULLY

AND RETAINED FOR FUTURE REFERENCE.

When using this electrical appliance, basic precautions should be followed to reduce the risk
of fire, electric shock and injury to person, including the following:

• This heater must be used on an AC supply only and the voltage marked on the heater’s
rating label must correspond to the supply voltage.

• DO NOT switch the appliance on until it is properly installed as described in this
manual.

• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance pro­vided that it has been placed or installed in its intended normal operating position and they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children aged from 3 years and less than 8 years shall not
plug in, regulate and clean the appliance or perform user maintenance.

• CAUTION: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are present.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.

• The heater must not be located immediately below a socket-outlet.

• DO NOT use this heater in the immediate surroundings of a bath, a shower or a swim-
ming pool.

• WARNING: In order to avoid overheating, do not cover the heater.

• DO NOT use this heater with a programmer, timer, separate remote-control system or
any other device that switches the heater on automatically, since a fire risk exists if the
heater is covered or positioned incorrectly.

• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal
cutout, this appliance must not be supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on and off by the utility.

• Keep furniture, curtains and other fabric material away from the appliance.

• DO NOT leave the appliance unattended during use.

• From time to time, check the cord for damage. Never use the appliance if the cord or any
part of the appliance shows signs of damage.

It is important that the following clearances are maintained from the appliance to combustible materials and are dependant on the desired
mounting location as defined below.

This appliance is designed to be wall mounted only. Do not stand it on the floor.

The minimum distance from the top of the appliance to a ceiling is 500mm.
The minimum distance from the bottom of the appliance to the floor is 100mm.
The minimum distance to the sides of the appliance is 100mm.
The minimum distance to the front of the appliance is 500mm.

4.0 SITE REQUIREMENTS

5.0 CLEARANCES TO COMBUSTIBLE MATERIALS

© 2016 Focal Point Fires plc.

3

3.0 ELECTRICAL INSTALLATION REQUIREMENTS

• DO NOT run the mains cable under carpets, rugs etc.

• DO NOT cover or obstruct the heater in any way. Overheating will result if it is acci-
dentally covered.

• Never immerse the product in water or any other liquids.

• DO NOT use the appliance outdoors.

• Before cleaning the appliance, ensure it is unplugged from the power and that it is com­pletely cool.

• DO NOT clean the appliance with abrasive chemicals.

• Never use accessories that are not recommended or supplied by the manufacturer. It
could cause danger to the user or damage to the appliance.

• DO NOT insert or allow foreign objects to enter the inlet or outlet vents as this may
result in electric shock, fire or damage to the appliance.

• DO NOT install the fire using an extension cord.

• Unplug from the mains supply if the appliance is not to be used for long periods.

The appliance is designed to be wall mounted via the wall mounting plate and fixings provided. The wall should be relatively flat and not inter­fere with any of the ventilation slots in the appliance casing.
The wall must be structurally sound and of a material capable of withstanding moderate heat. Finished plaster, conventional wallpaper, dry-lined
plaster board are examples of suitable materials. Materials such as “flock” blown vinyl”, embossed paper and cloth wall coverings which are sen­sitive to even small amounts of heat should be avoided, as some discolouration may occur. It should be noted that the appliance creates warm
convected air currents. These currents move heat from the room surroundings to, and up the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air, (such as tobacco smoke) exist,
may slightly discolour wall finishing.
If the appliance is to be mounted on a dry lined or timber framed construction then the integrity and ability of the wall to carry the weight of
the appliance must be confirmed. It is important in these circumstances that any vapour barrier and/or structural members of the house frame
are not damaged. If you are unsure of the ability of the wall to carry the weight and/or which type of wall fixing to use, you should take pro­fessional advice and obtain the correct fixings. Alternatively, find a more suitable wall location.

DO NOT - mount on a ceiling or floor.

- recess any part of the appliance into the wall.

- site any electrical equipment e.g. plasma screen TV sets etc,

on the wall above the appliance.

- site in a position where curtains or drapes could cover the appliance.

- site in a position where other soft materials could cover e.g. below a coat rack.

- site behind an opening door where mechanical impact/damage could occur.

- site where the supply cable would become a trip hazard.

- sit, stand or forcefully pull on the appliance.

- obstruct, cover or force items into the openings.

- use the heater to dry clothes.

- site/use in an outdoor location(s).

- run the supply cable under carpets.

2.0 APPLIANCE DATA

Weight (kg): 17.0 kg Supply Cord: 2 metres
Dimensions (mm): H 466 x W 757 x D 100 Fuse: 13Amp

Supply Voltage and rating power: 220-240V a.c. 50/60Hz, 1716 - 2016 Location: Indoor Use

Heating Elements: 2 x 900/1000Watts (1.8 - 2.0kW) LCD Display: 16 Watts

DO NOT RECESS ANY PART OF THE APPLIANCE.

The appliance is supplied with a pre-wired three pin plug (13 Amp fuse rated), and 2 metre cable. A standard switched outlet/wall socket, (includ­ing earth provision), must therefore be located within this distance, and be easily accessible in order to isolate the supply for maintenance and
cleaning. This socket must not be mounted behind or above the appliance.

IMPORTANT: THIS APPLIANCE MUST BE EARTHED.

1.0 PRELIMINARY NOTES - CONTINUED

GB IE