Ekofires eko 1010 Installation And User Instructions Manual

installation and user instructions

All instructions must be handed to user for safekeeping

Revision A - 06/09

Country(s) of destination - GB/IE

eko 1010

electric wall heater

Please note : Except where otherwise stated, all rights, including copyright in the text, images and layout of this book­let is owned by Focal Point Fires plc. You are not permitted to copy or adapt any of the content without the prior writ­ten permission of Focal Point Fires plc.

Manufactured by : Focal Point Fires plc.

Christchurch, Dorset BH23 2BT
Tel: [phone] Fax: [phone]
www.ekofires.co.uk
e-mail: [e-mail]

© 2009 Focal Point Fires plc.

CONTENTS

PRELIMINARY NOTES

The eko 1010 electric wall heater provides convected heating in conjunction with a visual fuel
effect display.

The appliance is designed for indoor use, and can be simply wall mounted in the majority of wall posi­tions anticipated. It can can be located in any household room, with the exception of bathrooms.
Read all of the instructions before commencing installation. Retain for future reference and pass on
as necessary to subsequent owners of the appliance.

DO NOT use this appliance immediately below a fixed socket outlet.
DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area

where water/moisture could present a hazard.

• CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal
control, or any other device that will switch on the appliance automatically, as a fire risk may occur

if the heater is accidentally covered or displaced.

• Do not allow the heater to be covered as this may cause overheating. The appliance must not be

placed near curtains or similar material. A clearance space of at least one metre should be allowed
in front of the appliance.

• The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply

cord directly in front of the heater unit.

• If the cord is damaged, it must be replaced by a service agent or competent person.

• This appliance is not intended for use by persons (including children) with reduced physical, sen-

sory or mental capabilities, or lack of experience and knowledge, unless they have been given super

vision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

APPLIANCE DATA

ELECTRICAL INSTALLATION REQUIREMENTS

The appliance is designed to be wall mounted using the brackets and fixings provided.

DO NOT RECESS ANY PART OF THE APPLIANCE.

The appliance is supplied with a pre-wired three pin BS1363 plug (13 Amp fuse rated), and 2 metre
cable. A standard switched outlet/wall socket, (including earth provision), must therefore be located
within this distance, and be easily accessible in order to isolate the supply for maintenance and clean­ing. This socket must not be mounted behind or above the appliance.

IMPORTANT: THIS APPLIANCE MUST BE EARTHED.

1

Section Contents Page No.

1.0 Preliminary Notes 1

2.0 Appliance Data/Specifications 1

3.0 Electrical Installation Requirements 1

4.0 Site Requirements 2

5.0 Clearances to Combustible Materials 2

6.0 Unpacking the Appliance 3

7.0 Component Checklist 3

1.0

Section Contents Page No.

8.0 Preparing the Appliance 3

9.0 Fixing the Appliance 4

10.0 Operating the Appliance 5

11.0 Safety Cut-Out System 5

12.0 Maintenance - Lamp Replacement 6

13.0 Cleaning 6

14.0 Servicing 6

Weight (kg): 10.0KG
Dimensions (mm): H 585 x W 500 x D 133
Voltage (Volts): 230-240V a.c. 50Hz
Heating Elements: 2 x 900/1000 Watts
Supply Cord: 2 metres
Supply Plug: BS 1363, 13A Fused
Location: Indoor Use
Lighting: 1 x 60W Amber B.C. Bulb

2.0

3.0

© 2009 Focal Point Fires plc.