Ekofires 1060 LED INSET ELECTRIC FIRE, 1070 LED REFLECTIONS INSET ELECTRIC FIRE, FRET AND FRAME OPTIONS AVAILABLE, 1060, 1070 Installation & User's Instructions

INSTALLATION & USER INSTRUCTIONS

LED ELECTRIC FIRE

1

Revision B - 01/14

' 2014 Focal Point Fires plc.

GB IE

All instructions must be handed to the user

for safekeeping.

Please note : Except where otherwise stated, all rights,
including copyright in the text, images and layout of this
booklet is owned by Focal Point Fires plc. You are not per­mitted to copy or adapt any of the content without the
prior written permission of Focal Point Fires plc.

MODELS COVERED BY THESE INSTRUCTIONS

1060 LED INSET ELECTRIC FIRE

1070 LED REFLECTIONS INSET ELECTRIC FIRE

FRET AND FRAME OPTIONS AVAILABLE

Christchurch, Dorset BH23 2BT

Tel: [phone]
Fax: [phone]
www.ekofires.co.uk

e-mail: [e-mail]

PL EASE NOTE: EKO 1060/ 1070 ELECTRIC FIR ES M AY BE SUPPLI ED WIT H DI FFERENT FRET & FRAME

TH AN S HOWN

MODEL SHOWN: EKO 1060 LED INSET ELECTRIC FIRE

The appliance is designed for indoor use, and can be simply floor mounted in the majority of floor positions anticipated. It can be located in any
household room, with the exception of bathrooms. Read all of the instructions before commencing installation. Retain for future reference and
pass on as necessary to subsequent owners of the appliance.

•

DO NOT use this appliance immediately below a fixed socket outlet.

•

DO NOT use this appliance in an open flue.

•

DO NOT use this appliance in the immediate vicinity of a bath, shower, swimming pool or other area where water/moisture could pres-

ent a hazard.

•

CAUTION: This appliance must not be used in conjunction with any timer, programmer or thermal control, or any other device that

will switch on the appliance automatically, as a fire risk may occur if the heaters are accidentally covered or displaced.

•

CAUTION: Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and

vunerable people are present.

•

WARNING: Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less

than 8 years shall only switch on/off the applaince provided that it has been placed or installed in its intended normal operating position and
they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged
from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

•

WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when

they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
Do not allow the heater to be covered as this may cause overheating. The appliance must not be placed near curtains or similar material. A
clearance space of at least one metre should be allowed in front of the appliance.
The electrical socket that the appliance uses MUST be easily accessible. Do not route the supply cord directly over or above the heater unit. If
the cord is damaged, it must be replaced by a service agent or competent person.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

The appliance is suitable for installation into all proprietary surrounds with an opening of 406mm by 559mm (16” by 22”). The appliance is sup­plied fitted with 2 spacer frames enabling it to be fitted with no need for a recess into a wall or surround back panel. Both spacer frames have
a depth of 57mm. The appliance can be fully recessed if the opening depth is 113mm or greater and neither spacer is used. It may be installed
directly into any proprietary surround which can house this size of rebate, without the need to recess the appliance into a wall opening or fab­ricate a false chimney breast.

This appliance should be positioned on a firm level surface and in a clean ‘dust free’ environment. If the fire is to be sited in a fire surround then
the suitability of the surround for use with electrical heaters should be established with the fire surround manufacturer.
If fitted into an open draught fireplace, it is recommended to blank off the chimney to reduce the risk of draught through the fire, which may
cause the safety cut out system in the fan heater to operate.

1.0 PRELIMINARY NOTES

I N S TA L L AT I O N & U S E R I N S T R U C T I O N S

' 2014 Focal Point Fires plc.

2

GB IE

2.0 APPLIANCE DATA

Weight (kg): 14 kg
Voltage (Volts): 220-240V a.c. 50Hz
Rated Power 2 x 900W/ 2 x 1000W
Supply Plug: BS 1363, 13A Fused
Supply Cord: 1.7 Metres
Location: Indoor Use
LED Display: 25 Watts

Section Contents Page No.

1.0 Preliminary Notes 2

2.0 Appliance Data 2

3.0 Installation Requirements 2

4.0 Unpacking The Appliance 3

5.0 Component Checklist 3

6.0 Installing The Appliance 3

Section Contents Page No.

7.0 Removing the appliance spacer frames 4

8.0 Fitting The Decorative Frame And Front 5

8.1 Fitting The Loose Fuel Bed Options 5

9.0 Operating the Appliance 6

10.0 Safety Cut-Out System 6

11.0 Cleaning And Maintenance 6

12.0 Guarantee - Terms And Conditions 7

3.0 INSTALLATION REQUIREMENTS

DO NOT

- site in a position where curtains or drapes could cover the appliance.

- site in a position where other soft materials could cover e.g. below a coat rack.

- site behind an opening door where mechanical impact/damage could occur.

- site where the supply cable would become a trip hazard.

- sit, stand or forcefully pull on the appliance.

- obstruct, cover or force items into the openings.

- use the heater to dry clothes.

- site/use in an outdoor location(s).

- run the supply cable under carpets.

- Mount on a wall.

Read all the instructions before continuing to unpack or install this appliance. Carefully remove the appliance from its packaging and lay on the
floor with it’s back surface downward. Note: DO NOT stand the appliance on its frame as this may cause distortion. Check that the remaining
packaging contents correlate with the component checklist below. Please dispose of all packaging with care at your local recycling centre.

QUANTITY DESCRIPTION

1 Heater main body
1 Decorative Frame
1 Decorative Fret with aspan door
1 Neoprene securing strip
1 Loose coal set (only available with Lulworth model)
1 Loose pebble set (only available with Lulworth model)
1 Instruction Booklet

3.0 INSTALLATION REQUIREMENTS - CONTINUED

GB IE

4.0 UNPACKING THE APPLIANCE

' 2014 Focal Point Fires plc.

3

5.0 COMPONENT CHECKLIST

6.0 INSTALLING THE APPLIANCE

Dependent on your installation requirements, you may wish to install the appliance in three different ways.

1: Flat wall – If you are putting the fire against a wall with no recess, you will use both of the

spacers that are fitted to the fire. You will be able to use either the sticky double sided neoprene
strips, or, secure the fire to the wall using the key hole slots on the rear of the spacer frame with
screws.

2: Semi recessed - If you are putting the fire against a wall with a recess of 60mm or more, you
will be able to remove one of the spacers that are fitted to the fire, so that your fire can sit fur­ther back on the hearth. You will be able to use either the sticky double sided neoprene strips, or,
secure the fire to the wall using the key hole slots on the rear of the spacer frame with screws.

See section 7.0 Removing the appliance spacer frame.

Method 1 - Installation with spacer/s

Neoprene – To use the Double sided Neoprene strip, you will need to cut the length into three equal pieces. Install one either side of the bot-

tom rear of the spacer and one on the top center of the spacer.

Flat wall installation

Semi recessed installation

Fully recessed installation