eKey home CP WM 1, ekey home CP WM 2, ekey home CP WM 3, ekey home CP IN 1, ekey home CP IN 2 Quick Start Manual

3. Programming the system with the ekey home CP WM 1(3) and with the ekey home CP IN 1(2)

The fu nction of the ekey home CP WM (IN)1(2,3) in the ekey
home system is to program and parametrize the system. Using

the

7-segment display and the
4 buttons,

you can

Register users and enroll their fingers
Delete users
Enter the security code
Change the security code
Change the relay switching times
Reset to factory settings

The menu navigation is intuitive and very easy. You will find
step-by-step detailed explanations of each specific menu
function on page 2.

3.1.Function of the control panel

3.2.Controls and their symbols

3.3.

Programming the system

Now start programming the system. The menu
sequences for each single function are
explained below of this document. Let us not

forget to mention the security code. You need it in
order to be able to make changes in the system.

The factory default setting for this code is

99. Change this code to another one of your
choice as soon as you have started up the
system.

The OK button allows you to register
values and move to the next menu level.

The Right arrow button allows you
set values and navigate in the menu.

The Left arrow button allows you to
set values and navigate in the menu.

The ESC butto n allows you to exit a
menu level or to cancel entries.

Symbol for the 7

-

segment display

on the

ekey home

CP

Represents that which is displayed o n the control panel during
the programming procedure and when it is operational.

QUICK START GUIDE

Before you start p rogramming the system with the help of this
quick-start guide, the system must be mounted and wired
according to the m ounting instructions and wiring plan supplied
with the device. Please follow the steps below:

1.) Make everything you need ready to mount the devices as
described in the mounting instructions supplied with the devices.

2.) Wiring

Do not connect the system to the mains yet! The electrical
connection of the system can only be carried out by a
specialist!

Connect the wires as described in the ekey home wiring plan supplied
with the devices.

3.) Check the wiring.

4.) Conclude mounting the devices. Close all the device housings

which you had to open in order to be able to proceed with the wiring.

5.) Read carefully the following chapter

„ 2 Operating the finger scanner“. The correct
operation (i.e. swiping the finger over the sensor) of
the fingerprint scanner is decisive for the proper
functioning of the whole system.

6.) Connect the power adaptor to the mains.

The electrical connection of the system can only be carried out
by a specialist!

A couple of seconds later, 2 red dots show up on the display of the
ekey home CP WM (IN)1(2,3).

The ekey home finger scanner indicators are as follows:

7.)

Now st art at point A: INITIALIZE DEVICES of „Programming

the system“.

2 Operating the finger scanner

The function of the finger scanner is to capture and analyze the image of your finger, and then

compare it with a reference template. Which part of your finger should be captured?

A finger scanner works like a camera. It makes a picture of the bottom sid

e, the papillary lines, of

your finger´s third phalanx. However, this picture must be of good quality, so that physical access
can be granted whenever necessary.

Imagine you wish to make a picture of someone, and this person

keeps fidgetting
runs by and you try to make a picture of him at that exact moment
hides half of his face behind a tree

etc.
What do you think these pictures will look like? On some of the pictures you will not even be able
to recognize the person.

The finger scanner works in the same way. The finger scanner can only read all the information
contained in your finger, and consequently open your doors securely and reliably, if yo u move
your finger down across the sensor evenly and in the right position.
Let us now look at where you should place your fingers and at which speed you should move them
across the sensor, so that the „pictures“ of your fingers are perfect.

It is necessary to capture an image of the
3rd phalanx. On the contrary, your finger
scanner will not function properly.
In order t o ensure this, take care to
operate the finger scanner correctly. It is
fundamental to place your finger correctly
in the finger recess and move it down
across the sensor at the right speed.

2.1.Function of the finger scanner

2.3. Operating correctly the finger scanner

Place the middle of

your third phalanx

directly on the

finger recess pin

point

.

BE SURE to place

your finger exactly

in the middle of

the area between

both finger recess

edges.

Lay your finger straight and flat

on the finger recess.

Ideally, when positioning your

finger on the finger recess, stretch

the remaining fingers, holding them

close to the „swiping“ finger. This

helps keep the „swiping“ finger

even.

Now without changing the inclination of your finger, move it down

across the sensor (the entire hand). Take care to swipe your finger
at the right speed. BEWARE: The entire movement (swipe) should
take about

1-1,5sec

.
Use this as a benchmark. You should not need much more or much
less than that.
Do not modifiy the position of the finger phalanges during the
swipe (e.g. by bending the third phalanx).
There is no need to exert any stronger pressure. Move your
finger across the sensor as if you would w ipe bread crumbs off a
table.

2.4. What you should not do

2.2 The finger recess

– the control element

Place your third phalanx

higher than the pin point

Not place your finger in the middle

of the finger recess, or not place it
parallel to the finger recess edges.

Rotate your finger in the

finger recess.

Place your finger at a too

steep angle with the

finger recess.

Move your

finger too fast
or too slowly
across the
sensor.

The finger recess allows to place the finger correctly so that a finger picture of good quality

can be captured. It actually is the control element and consists of

pin point - sensor –

right and left recess edges.

Take care to position

your finger as flat as

possible over the

finger recess.

If you move your finger across the finger scanner in one of the

ways mentioned here, then the scanner will not be able to
extract the information it needs about your finger image. It
will therefore not function properly:

Poor recognition performance: Yo u will have to swipe your

finger several times across the sensor before being able to
induce the door to open.
Reference templates cannot be saved: You are not abel to
save a finger in the system, because the fingerscanner gets less
information.

Finger nail

3rd phalanx

(phalanx distalis)

2nd phalanx

(phalanx media)

Finger image

(papillary
lines) of t he

3rd phalanx

V >>

ekey home

CP WM

(IN) 1(2,3)

Access system with fingerprint

This quick-start guide as well as the additional information and instructions on the

supplied DVD are not subject to updating. You can find the most up-to-date version of
these documents on www.ekey.net. Subject to optical and technical modifications,
any liability for misprints excluded.

ID4/

129/0/53:

Version 2

dated 22.6.2012

ekey home FS

WM

ekey home FS IN

ekey home FS OM

flashing orange

Note on the document

1 Start-up

PIN POINT

SENSOR

L

eft and

right recess edge

C: RECORD

ING FINGERPRINTS (Eu)

With Enroll User the following occurs:

Allocation of a user to a memory space: 0 - 99
Selection of the fingerprint number: F1 – F10 (F0)

Allocation of the fingerprint to a switching relay (with ekey home 2, 3 and PC): o1 – o3; od (Relays 1 and 2 switch together with one finger)

Finger enrollment: a finger must have been captured at least 3 times, before it can be saved as a template. Depending on the quality assessment this may have to be done regularly!

CODE

DISPLAY KEY

STROKE

DISPLAY +

SETTING

KEY

STROKE

DISPLAY +

SETTING

KEY

STROKE

DISPLAY +

SETTING

KEY

STROKE

DISPLAY Swipe USER

FINGER

DISPLAY

DISPLAY DISPLAY

SEE

B:

Select 0-99 for
USER NUMBER

Select F1-F10 for

FINGER NUMBER

Select RELAY o1-o3

or od

ZIEHEN

START

The red dot only lights up if the

memory is already occupied (a

USER or fingerprint had already

been saved to this position)!

It is

not possible to choose

the relay o n control panels
featuring only one relay:

ekey home CP WM1
ekey home CP IN1

It has not yet been possible to capture 3 fingers, or the
captured finger is of poor quality.

The finger image is of very poor quality. Try it once again,
read Chapter 2 of the Operating Instructions.

The quality of the finger image is good, but not excellent.
You may either exit enrollment by pressing the OK button
or try to achieve an excellent quality!

Although a finger has been swiped over the finger

scanner, the device has not discerned any finger swipe.
Read chapter 2 of the Operating Instructions and then

D
O
N
E

3 finger

templates

have been

captured

successfully!

Your user

finger has

now been

enrolled!

Recommended f

inger

numbering F1-F0

A: INITIALI

ZING THE DEVICES

The devices have to be initialized. Only after this can fingerprints be saved. Proceed as follows:

DISPLAY KEY

STROKE

DISPLAY KEY

STROKE

DISPLAY KEY

STROKE

DISPLAY DISPLAY

The devices have now been

initialized. You may start

enrolling users->

See C:

DONE

START

Security code

Factory setting

99

B: ENTERING THE SECURITY CODE

The security code is used to prevent unauthorized people having access to your system and thereby changing data. The factory default setting for this code is “99”: change this code straight after
having started up the system in order to ensure protection from manipulation. The necessary entries to change the code can be found in section F:.

DISPLAY KEY

STROKE

DISPLAY +

SETTING

KEY

STROKE

DISPLAY +

SETTING

KEY

STROKE

DISPLAY

Security code

DIGIT 1

Security code

DIGIT 2

START

DONE

Now you can make the

entries and data changes

in your system.

Der NEUE

Sicherheits code ist

damit ak tiv!

F: CHANGING THE SECURITY CODE (Sc)

ENTER SECURI TY

CODE

DISPLAY +

SETTING

KEY STROKE DISPLAY +

SETTING

KEY STROKE DISPLAY +

SETTING

KEY STROKE DISPLAY DISPLAY

SEE B:

Select

MEN

U

ITEM Sc

NEW

CODE

DIGIT 1

NEW

CODE

DIGIT 2

DONE

START

G: RESETTING TO FACTORY SETTINGS (rr)

Warning! All stored fingers will be deleted! The system has to be re-initialized (see A:)

ENTER SECURI TY

CODE

DISPLAY +

SETTING

KEY STROKE DISP LAY +

SETTING

KEY STROKE DISP LAY +

SETTING

KEY STROKE DI SPLAY DISPLAY

SEE B:

Select

MEN

U

ITEM rr

Security code

DIGIT 1

Security code

DIGIT 2

Your device is now

back in its delive red

condition!

STAR

T

The NEW security code is

now active !

D: DELETING USERS (du)

ENTER SECURI TY

CODE

DISPLAY +

SETTING

KEY STROKE DISPLAY +

SETTING

KEY STROKE D ISPLAY DISPLAY

SEE

B:

Select

MEN

U

ITEM du

Select

USER

NUMBER

STAR

T

The selected USER

has been deleted!

Relaisschal tzeit für das

gewählte Re lais ist

eingestel lt!

E: RELAY SWITCHING TIME (rt)

–

The switching ti me of each re lay can be set from 1 sec to 99 se c..If 0 is set then the relay works as a toggle relay.

ENTER SECURI TY

CODE

DISPLAY +

SETTING

KEY STROKE DISPLAY +

SETTING

KEY STROKE DISPLAY +

SETTING

KEY STROKE DISP LAY DISPLAY

SEE B:

Select

MEN

U

ITEM rt

Select RELAY

Switching time in

seconds (1-99)

STAR

T

The rela y switching time for
the selecte d relay has been

set!

Errors codes on the display:

Error code „E2“: You have entered the

wrong code three times in a row. The s ystem
will be completely locked for 30 mn.

Error code „E0“: There is no data connection
to the finger scanner. Check the wiring and
make sure that all the devices ares connected
correctly to the mains!

At least

3

times