User’s Manual
â
FlexScan
F35/FX·B5
Color Display Monitor
English
CONTENTS
PRECAUTIONS i
INTRODUCTION 5
About This Manual ............................................... 5
Package Contents ............................................... 5
1 FEATURES 6
Features .............................................................. 6
Functions............................................................. 7
2 IMAGING ADJUSTMENT 8
- Screen menu -
Brightness, Contrast, Size, Position.................... 8
Geometry, Tilt ...................................................... 8
Moiré Reduction .................................................. 9
2
3 COLOR ADJUSTMENT 10
- Color menu -
Outline ............................................................... 10
Adjusting the Standard mode ............................ 11
Adjusting the Custom mode .............................. 12
4 POWER-SAVE SETUP 15
- PowerManager menu -
Set-up Procedure .............................................. 16
AutoPower Function .......................................... 19
For installation, see the ‘Quick Setup Guide’.
CONTENTS
5 OTHER SETTINGS 20
- Others, Information and Language menus -
Degaussing ....................................................... 20
Beep .................................................................. 21
Menu Position, Menu Contrast .......................... 21
Reset................................................................. 21
Information status report ................................... 22
Language menu ................................................. 22
6 GETTING THE MOST FROM YOUR MONITOR
23
Adjustment Lock ............................................... 23
Optional i·Sound™ speaker system ................... 23
7 TROUBLESHOOTING 24
Troubleshooting ................................................. 24
8 CLEANING 29
E
9 SPECIFICATIONS 30
APPENDIX 99
CONTENTS
3
Copyright© 2000 by EIZO NANAO CORPORATION. All rights reserved. No part of
this manual may be reproduced, stored in a retrieval system, or transmitted, in any form
or by any means, electronic, mechanical, or otherwise, without the prior written
permission of Eizo Nanao Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to Eizo Nanao
Corporation's receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date
information, please note that EIZO monitor specifications are subject to change without
notice.
Apple and Macintosh are trademarks of Apple Computer Inc.,registered in the U.S. and other countries.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards Association.
VGA is a registered trademark of International Business Machines Corporation.
ENERGY STAR is a U.S. registered mark.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager, PowerManager, QuickSet, i·Sound and i·Station are trademarks of Eizo Nanao Corporation.
FlexScan, SuperErgoCoat and EIZO are registered trademarks of Eizo Nanao Corporation.
CONTENTS
4
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
PRECAUTIONS
SICHERHEITSHINWEISE
PRÉCAUTIONS
PRECAUTIONS
i
PRECAUTIONS
E
Location of the caution statements
Jordet stikkontakt skal benyttes når apparatet tilkobles datanett.
Apparaten skall anslutas till jordat nätuttag.
The equipment must be connected to a grounded main outlet.
IMPORTANT!
To ensure personal safety and proper
maintenance. Please read this section
and the caution statements on the
monitor (refer to the figure above).
This manual uses the safety symbols below.
They denote critical information.
Please read them carefully.
ii
Indicates a prohibited action.
Indicates to ground for safety.
WARNING
Failure to abide by the information in a
WARNING may result in serious injury
and can be life threatening.
CAUTION
Failure to abide by the information in a
CAUTION may result in moderate injury
and/or property or product damage.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
Position des WarnhinweisAufklebers
WICHTIG!
Zu Ihrer eigenen Sicherheit und um
ordnungsmäße Handhabung Ihres
Systems zu gewährleisten, sollten Sie
unbedingt diesen Abschnitt und die
Warnhinweise auf Ihrem Monitor lesen
(siehe obige Abbildung).
In diesem Handbuch werden die
nachfolgend aufgeführten
Sicherheitssymbole verwendet. Diese
Symbole verweisen auf wichtige
Informationen. Lesen Sie die markierten
Abschnitte daher sorgfältig durch.
Signalisiert eine verbotene Aktion:
Emplacement de l’étiquette de
sécurité
IMPORTANT!
Pour votre sécurité et pour assurer un
entretien correct, veuillez lire cette
section ainsi que les avertissements
sur votre moniteur.
Ce manuel utilise les symboles de sécurité
présentés ci-dessous, qui mettent en
évidence des informations essentielles.
Veuillez les lire attentivement.
Indique une action interdite.
Signalisiert, daß aus Sicherheitsgründen
eine Erdung vorzunehmen ist.
WARNUNG
Die Nichtbeachtung der mit WARNUNG
gekennzeichneten Textstellen kann zu
schweren Verletzungen (evtl. mit
Todesfolge) führen.
ACHTUNG
Die Nichtbeachtung der mit ACHTUNG
überschriebenen Textstellen kann leichtere
Verletzungen und/oder eine Beschädigung
des Produkts sowie sonstiger
Ausrüstungseinheiten nach sich ziehen.
Indique que la mise à la terre est
obligatoire pour la sécurité.
AVERTISSEMENT
Le non respect des consignes données dans
un AVERTISSEMENT peut entraîner des
blessures sérieuses ou même la mort.
ATTENTION
Le non respect des consignes données dans
un ATTENTION peut entraîner des
blessures et/ou des dommages au matériel
ou au produit.
PRECAUTIONS
iii
PRECAUTIONS
E
WARNING
• If the monitor begins to emit smoke,
smells like something is burning, or
makes strange noises, disconnect all
power connections immediately and
contact your dealer for advice.
Attempting to use a malfunctioning
monitor can be dangerous.
• Do not dismantle the cabinet or modify
the monitor.
Dismantling the cabinet or modifying the
monitor may result in electric shock or
burn.
• Keep small objects away from the
monitor.
Small objects may accidentally fall through
the ventilation slots into the cabinet,
leading to fire, shock, or equipment
damage.
iv
• Keep liquids away from the monitor.
Spillage into the cabinet may result in fire,
electric shock, or equipment damage.
If an object or liquid falls/spills into the
cabinet, unplug the monitor immediately.
Have the unit checked by a qualified
service engineer before using it again.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
WARNUNG
• Tritt Rauch aus dem Monitor aus oder
werden ungewöhnliche Geräusche
oder Gerüche wahrgenommen, sind
umgehend sämtliche
Netzverbindungen zu lösen.
Wenden Sie sich in diesem Fall an Ihren
Händler. Der Einsatz eines defekten
Monitors kann gefährlich sein.
• Gehäuse keinesfalls öffnen und keine
Änderungen am Monitor vornehmen.
Beim Öffnen oder Zerlegen des Gehäuses
sowie der Durchführung etwaiger
Änderungen am Monitor besteht
Stromschlag- und Verbrennungsgefahr.
• Bringen Sie keine kleinen Gegenstände
in die Nähe des Monitors.
Kleinere Gegenstände könnten
versehentlich durch die Lüftungsschlitze in
das Gehäuseinnere gelangen, was mit
Brand- oder Stromschlaggefahr verbunden
ist oder zu einer Beschädigung des Geräts
führen könnte.
• Bringen Sie keine Flüssigkeiten in die
Nähe des Monitors.
Wenn Flüssigkeit in das Geräteinnere
gelangt, besteht Brand- oder
Stromschlaggefahr, und der Monitor
könnte beschädigt werden.
Sollte dennoch Flüssigkeit oder ein
Gegenständ in das Gehäuseinnere
eindringen, ist umgehend der Netzstecker
des Monitors zu ziehen. Lassen Sie das
Gerät in diesem Fall vor dem nächsten
Einsatz von einem Fachmann überprüfen.
AVERTISSEMENT
• Si le moniteur commence à fumer ou
produit un bruit ou une odeur
anormale, débranchez immédiatement
tous les câbles secteur et prenez
contact avec votre revendeur.
Il est dangereux de tenter d’utiliser un
moniteur au fonctionnement défectueux.
• Ne tentez jamais de démonter la
carrosserie ni de modifier le moniteur.
Le démontage de la carrosserie ou la
modification du moniteur vous exposent à
un choc électrique ou à une brûlure.
• Eloignez les petits objets du moniteur.
Des petits objets tombés par accident dans
les fentes de ventilation de la carrosserie
peuvent entraîner un incendie, un courtcircuit ou endommager l’appareil.
• Eloignez les liquides du moniteur.
Le renversement de liquide à l’intérieur de
la carrosserie peut entraîner un incendie,
un court-circuit ou endommager le
matériel.
Au cas où un objet ou un liquide
pénétrerait dans la carrosserie, débranchez
immédiatement le moniteur. Faites-le
vérifier par un technicien qualifié avant de
l’utiliser à nouveau.
PRECAUTIONS
v
OK
PRECAUTIONS
E
• Place the monitor on a strong, stable
surface.
A unit placed on an inadequate surface
may fall, resulting in injury or equipment
damage.
If the monitor falls, disconnect the power
immediately and have the unit checked by
a qualified service engineer before using it
again. Using a monitor after it has been
dropped may result in fire or electric shock.
• Keep the plastic packing bags away
from children and infants.
Plastic bags can be dangerous. To avoid
danger of suffocation, keep the bag away
from babies and children.
vi
PRECAUTIONS
• Keep power terminal covers for the
optional i·Sound
children and infants.
Children and infants may accidentally
swallow the covers and choke. If
swallowed, consult a doctor immediately.
• The equipment must be connected to a
grounded main outlet.
ää
ä
ää
sound unit away from
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
• Stellen Sie den Monitor auf eine stabile
ebene Fläche.
Wird das Gerät nicht ordnungsgemäß
aufgestellt, kann es herunterfallen und
jemanden verletzen bzw. selbst beschädigt
werden.
Nach einem Sturz muß der Monitor
umgehend vom Netz getrennt und vor dem
nächsten Einsatz durch einen Fachmann
überprüft werden. Bei Einsatz eines
defekten Geräts besteht Brand- und
Stromschlaggefahr.
• Kunststoffverpackungen gehören nicht
in Kinderhände!
Kunststoffverpackungen (insbesondere
Tüten) sind gefährlich. Um
Erstickungsgefahr auszuschließen, sollten
Sie daher dafür sorgen, daß die Verpackung
nicht in Kinderhände gelangt.
• Schützen Sie die Abdeckung des
Spannungsversorgungsanschlusses
für das optionale i·Sound
ÔÔ
Ô
ÔÔ
Lautsprechersystem vor dem Zugriff
durch Kinder oder Kleinkinder.
Kinder bzw. Kleinkinder könnten die
Abdeckung versehentlich
herunterschlucken. Hierbei besteht
Erstickungsgefahr. Sollte dies dennoch
geschehen, sollten Sie umgehend einen Arzt
aufsuchen.
• Placez le moniteur sur une surface
stable et solide.
Un appareil placé sur une surface inadaptée
risque de tomber, ce qui peut
l’endommager et entraîner des blessures.
En cas de chute du moniteur, débranchez-le
immédiatement du secteur et faites-le
vérifier par un technicien qualifié avant de
l’utiliser à nouveau. L’utilisation du
moniteur après une chute peut entraîner un
incendie ou un choc électrique.
• Conservez les sacs plastiques hors de
portée des enfants.
Les sacs plastiques peuvent être dangereux.
Pour éviter tout danger d’étouffement,
conservez ces sacs hors de portée des
enfants de tous âges.
• Conservez les capots des bornes du
système de haut-parleurs i·Sound
ÔÔ
Ô
ÔÔ
hors de portée des enfants et des
nourrissons.
Les enfants et les nourrissons pourraient
avaler ces capots et risquer un étouffement.
Dans ce cas, prévenez immédiatement un
médecin.
• Schließen Sie das System an eine
ordnungsgemäß geerdete Steckdose
an.
• Cet appareil doit être branché sur une
prise secteur avec terre.
PRECAUTIONS
vii
PRECAUTIONS
E
• Use the enclosed power cord. If using
the power cord other than the enclosed
one, use the following cord.
In USA and Canada:
* Rating: min. 125 V, 10 A
* Length: max. 2.1 m
*Type: SVT
* Plug type: NEMA 5-15P, Parallel blade,
In Europe:
* Rating: min. 250 V, 10 A
* Length: max. 2.1 m
*Type: H05VV-F 3G 1 mm
Use a plug type approved by the country
where you use.
Failure to do so may cause fire or electric
shock.
• Do not overload your power circuit, as
this may result in fire or electric shock.
• For proper connections of the power
cord, be certain to plug the power cord
to the provided monitor connector and
directly to a wall outlet.
By not doing so may result in fire or
electric shock.
Grounding type, 125 V, 10 A
2
viii
• Handle the power cord with care.
* Do not place the cord underneath the
monitor or other heavy
objects.
* Do not pull on the cord.
* Do not attempt to repair a damaged cord.
If the power cord becomes damaged, stop
using it. Use of a damaged cord may result
in fire or electric shock.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
• Verwenden Sie das mitgelieferte
Netzkabel. Bei Einsatz anderer
Netzkabel sind folgende
Spezifikationen einzuhalten.
In den Vereinigten Staaten und Kanada:
* Leistung: min. 125 V, 10 A
* Länge: max. 2,1 m
* Typ: SVT
* Steckertyp: NEMA 5-15P, Parallel-
Flachstift, Erdungstyp, 125 V, 10 A
In Europa:
* Leistung: min. 250 V, 10 A
* Länge: max. 2,1 m
* Typ: H05VV-F 3G 1 mm
Verwenden Sie unbedingt einen Steckertyp,
der für das jeweilige
Einsatzland zugelassen ist.
Anderenfalls besteht Brand- oder
Stromschlaggefahr.
• Vermeiden Sie Netzüberlastungen.
Bei Netzüberlastung besteht besteht Brandund Stromschlaggefahr.
• Beim Anschluß des Netzkabels ist
darauf zu achten, daß das Kabel mit
dem hierfür vorgesehenen
Monitoranschluß und einer
ordnungsgemäß geerdeten
Wandsteckdose verbunden wird.
Anderenfalls besteht Brand- oder
Stromschlaggefahr.
• N’utilisez que le cordon secteur fourni.
Si vous devez utiliser un autre cordon
secteur, vérifiez qu’il est conforme aux
caractéristiques ci-dessous.
Aux États-Unis et au Canada :
* Calibre : mini. 125 V, 10 A
* Longueur : max. 2.1 m
* Type: SVT
* Type de prise : NEMA 5-15P, lames
parallèles, Avec terre, 125 V, 10 A
En Europe :
* Calibre : mini. 250 V, 10 A
* Longueur : max. 2.1 m
*Type: H05VV-F 3G 1 mm
Utilisez le type de prise adapté au pays
d’utilisation.
Une utilisation incorrecte peut causer un
incendie ou un choc électrique.
• Ne surchargez pas les prises ou les
circuits électriques ; ceci pourrait créer
un incendie ou un choc électrique.
• Pour un branchement correct du câble
secteur, vérifiez que le câble fourni est
bien branché sur le connecteur du
moniteur et directement sur une prise
murale.
Tout autre branchement peut présenter des
risques d’incendie ou de choc électrique.
• Behandeln Sie das Netzkabel
schonend.
* Klemmen Sie das Netzkabel keinesfalls
unter den Monitor, und stellen Sie keine
schweren Gegenstände auf das Kabel.
* Ziehen Sie grundsätzlich nicht am Kabel,
sondern am Netzstecker.
* Versuchen Sie keinesfalls, ein defektes
Netzkabel selbst zu reparieren.
Ein defektes Netzkabel darf nicht länger
verwendet werden. Bei Einsatz eines
defekten Netzkabels besteht Brand- und
Stromschlaggefahr.
• Manipulez le câble secteur avec
précaution.
* Ne faites pas passer le câble sous le
moniteur ou un autre objet
lourd.
* Ne tirez jamais sur le câble.
* Ne tentez jamais de réparer un câble
endommagé.
Si le câble secteur est endommagé, ne
l’utilisez plus. L’utilisation d’un câble
défectueux peut entraîner un incendie ou
un choc électrique.
PRECAUTIONS
ix
OK
PRECAUTIONS
E
• To disconnect the power cord, grasp
the plug firmly and pull.
Never tug on the cord, doing so may cause
damage and could result in fire or electric
shock.
x
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
• Zum Lösen der Netzverbindung
Netzstecker fest greifen und aus der
Wandsteckdose ziehen.
Niemals ruckartig am Netzkabel ziehen, da
das Kabel hierdurch beschädigt werden
könnte, was wiederum mit Brand- oder
Stromschlaggefahr verbunden ist.
• Pour débrancher le câble secteur, tirez
seulement sur le connecteur ou la
fiche.
Ne tirez jamais sur le câble, ceci pourrait
l’endommager ou entraîner un incendie ou
un choc électrique.
PRECAUTIONS
xi
PRECAUTIONS
E
CAUTION
Be careful when taking the monitor out
of the carton:
• Disconnect the power cord, signal
cables and remove the optional
ää
ä
ää
i·Sound
sound unit and i·Station
hub (if applicable) when moving the
monitor.
Moving the monitor with the cord attached
or lifting it by the i·Sound sound unit or
i·Station USB hub is dangerous. It may
result in injury or equipment damage.
• Handle with care when carrying the
monitor
Note that the monitor is heavier at the
front than at the rear.
The screen is optically coated to reduce
glare. Keep hard objects (such as buttons,
tie pins, and other clothing accessories)
away from the screen surface to prevent
scratches.
ää
ä
ää
USB
xii
• Set the monitor in an appropriate
location.
* Do not install in a dusty or humid
environment.
* Do not place in a location where light
shines directly on the
screen.
* Do not place near heat generating devices
or a humidifier.
• Use an easily accessible power outlet.
This will ensure that you can disconnect
the power quickly in case of a problem.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
ACHTUNG
Beim Herausheben des Monitors aus
dem Verpackungskarton ist folgendes
zu beachten:
• Lösen Sie vor dem Transport des
Monitors das Netzkabel und die
Signalkabel, und entfernen Sie das
optionale i·Sound
Lautsprechersystem sowie den
i·Station
ÔÔ
Ô
ÔÔ
-USB-Hub (sofern verfügbar).
Erfolgt der Transport, ohne zuvor die
Kabelverbindungen zu lösen, oder wird der
Monitor am i-Sound-Lautsprechersystem
oder dem i-Station-USB-Hub angehoben,
besteht Verletzungsgefahr sowie die Gefahr
einer Beschädigung des Systems.
• Vorsicht beim Transport des Monitors.
Beachten Sie, daß der Monitor an der
Vorderseite schwerer ist als an der
Rückseite.
Der Bildschirm ist mit einer optischen
Beschichtung zur Vermeidung von
Blendeffekten versehen. Bringen Sie
keinesfalls harte Gegenstände (wie Knöpfe,
Krawattennadeln oder sonstiges
Kleidungszubehör) in die Nähe des
Bildschirms, um Kratzer zu vermeiden.
ÔÔ
Ô
ÔÔ
-
ATTENTION
Pour sortir le moniteur du carton:
• Débranchez le câble secteur et les
câbles de signal, déposez le système
de haut-parleurs i·Sound
ainsi que le concentrateur USB
i·Station
ÔÔ
Ô
ÔÔ
(le cas échéant) avant de
déplacer le moniteur.
Il est dangereux de déplacer le moniteur
quand les câbles sont branchés, comme de
le soulever par le système de haut-parleurs
i·Sound ou le concentrateur USB i·Station.
• Opérez avec précaution pour déplacer
ou transporter le moniteur.
Notez que le moniteur est plus lourd à
l'avant qu'à l'arrière.
L’écran a reçu un traitement de surface
spécial pour réduire les reflets. Empêchez
tout contact entre la surface de l’écran et
des objets durs (bouton, épingle de cravate
ou autres accessoires vestimentaires) pour
éviter les rayures.
ÔÔ
Ô
ÔÔ
en option
• Wählen Sie einen geeigneten Standort
für Ihren Monitor.
* Meiden Sie Standorte mit hoher
Staubeinwirkung oder Luftfeuchte.
* Meiden Sie Standorte, an denen der
Bildschirm direkter Lichteinwirkung
ausgesetzt ist.
* Meiden Sie die Nähe von Geräten mit
starker Hitzeabstrahlung sowie
Luftbefeuchter.
• Benutzen Sie eine leicht zugängliche
Wandsteckdose.
Auf diese Weise ist sichergestellt, daß Sie
den Monitor bei Auftreten eines Problems
schnell vom Netz trennen können.
• Installez le moniteur dans un emplacement approprié.
* Ne l’installez jamais dans un
environnement humide ou
poussiéreux.
* Evitez les sources de lumière directe sur
l’écran.
* Evitez la proximité de sources de chaleur
ou d’humidificateurs.
• Utilisez une prise murale facilement
accessible.
Ceci permettra de débrancher rapidement
l’appareil en cas de problème.
PRECAUTIONS
xiii
PRECAUTIONS
E
• Do not sit on the cabinet or place any
heavy objects on the cabinet.
A unit with heavy objects on it may fall or
be damaged and result in injury.
• Do not block the ventilation slots on the
cabinet.
* Do not place books or any other papers
on the ventilation slots.
* Do not install the monitor in a closed
space.
* Do not use the monitor laying down or
upside down.
* Do not remove the tilt-swivel stand.
Using the monitor in this way blocks the
ventilation slots and prevents proper
airflow, leading to fire or other damage.
xiv
• Do not remove the tilt-swivel stand.
The stand is required to maintain clearance
for the ventilation slots on the bottom of
the cabinet. Removing the stand will block
these slots and may result in fire or electric
shock.
• Do not touch the plug with wet hands.
Touching the plug with wet hands is
dangerous and can cause electrical shock.
• At the end of the day or if you plan to
leave the monitor unused for an
extended period, after turning off the
power switch disconnect the power
cord from the wall socket so that no
power connections are made.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
• Nicht auf das Gehäuse setzen und
keine schweren Gegenstände
darauflegen.
Ein Monitor, auf dem schwere Gegenstände
abgelegt werden, kann herunterfallen oder
beschädigt werden.
Hierbei besteht Verletzungsgefahr.
• Verdecken Sie keinesfalls die
Lüftungsschlitze des Gehäuses.
* Legen Sie keine Bücher oder sonstige
Gegenstände auf die Belüftungsschlitze.
* Installieren Sie den Monitor nicht in einem
geschlossenen Raum (Schrank etc.).
* Benutzen Sie den Monitor nicht in
liegender oder umgekehrter Position.
* Entfernen Sie keinesfalls den Dreh-/
Neigfuß.
In den oben beschriebenen Fällen werden
die Belüftungsschlitze verdeckt, wodurch
eine ordnungsgemäße Belüftung des
Monitors verhindert wird. Hierbei besteht
Brandgefahr, und der Monitor könnte
beschädigt werden.
• Entfernen Sie keinesfalls den DrehNeigfuß.
Der Dreh-/Neigfuß sorgt für einen
ausreichenden Abstand zwischen den
Belüftungsschlitzen am Gehäuseboden und
der Stellfläche. Bei Blockierung dieser
Schlitze besteht Brand- und
Stromschlaggefahr.
• Ne vous asseyez pas sur le moniteur et
n’y posez jamais d’objets lourds.
Une surcharge pourrait déséquilibre le
moniteur et vous exposer à des blessures.
• N’obstruez pas les fentes de ventilation
de la carrosserie.
* Ne placez pas de livres ou autres papiers
sur les fentes de
ventilation.
* N’installez pas le moniteur dans un
espace clos.
* N’utilisez pas le moniteur couché sur le
côté ni à l’envers.
* Ne démontez pas le socle orientable.
Ces utilisations du moniteur obstruent les
fentes de ventilation et empêchent une
circulation normale de l’air, ce qui peut
causer un incendie ou d’autres dégâts.
• Ne démontez pas le socle orientable.
Le socle est indispensable pour assurer la
ventilation par les fentes du bas de la
carrosserie.
Ces fentes de ventilation sont obstruées
quand le socle est démonté, cela peut
entraîner un incendie ou un choc
électrique.
• Das Netzkabel keinesfalls mit nassen
Händen anfassen.
Die Berührung des Netzkabels mit nassen
Händen ist gefährlich, es besteht
Stromschlaggefahr.
• Bei Tagesende bzw. wenn Sie Ihren
Monitor für einen längeren Zeitraum
nicht benötigen, sollten Sie nach dem
Ausschalten des Monitors zusätzlich
den Netzstecker ziehen, um die
Spannungsversorgung vollständig zu
unterbrechen.
• Ne touchez jamais les prises avec les
mains mouillées.
Le contact entre une prise et des mains
mouillées est dangereux, il peut causer un
choc électrique.
• Am la fin de la journée ou si vous
prévoyez de ne pas utiliser le moniteur
pendant un temps assez long,
débranchez le câble secteur de la prise
murale.pour isoler complètement le
moniteur du secteur.
PRECAUTIONS
xv
PRECAUTIONS
E
• Unplug the monitor before cleaning it.
Cleaning the monitor while it is plugged
into a power outlet may result in electric
shock.
For users of the EIZO optional i·Sound
sound unit and i·Station
ää
ä
ää
USB hub
• When adjusting the viewing angle of
the monitor, do not do so by handling
the sound unit or USB hub.
Adjusting the monitor in this way may
break the unit or cause bodily injury.
Others
• Do not install the monitor within an area
subject to strong magnetic fields (for
example, in the vicinity of a speaker, except
the optional i·Sound unit, or a highvoltage transformer). Magnetic fields can
cause noise, image shaking, and other
distortions.
ää
ä
ää
xvi
• Generally, for maximum viewing comfort
position the monitor slightly below eye
level. Staring at the monitor for prolonged
periods can cause eye strain. Be sure to
take adequate rests. (A 10-minute rest
period each hour is suggested.)
• Do not remove the covers to the power
terminal for the optional i·Sound speaker
unit for any reason except to attach the
unit.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
• Ziehen Sie vor dem Reinigen des
Monitors den Netzstecker.
Ist der Monitor während der Reinigung
mit der Wandsteckdose verbunden, besteht
Stromschlaggefahr.
Für Benutzer des optionalen i·SoundÔLautsprechersystems und des
i·StationÔ-USB-Hubs:
• Fassen Sie den Monitor bei Justage
des Sichtwinkels keinesfalls am
Lautsprechersystem oder dem USBHub.
Erfolgt die Sichtwinkelanpassung auf diese
Weise, können diese Einheiten abbrechen,
und es besteht Verletzungsgefahr.
Sonstiges
• Installieren Sie den Monitor nicht im
Bereich starker Magnetfelder,
beispielsweise in der Nähe von
Lautsprechern (außer der optionalen
i·Sound-Lautsprechereinheit) oder
Hochspannungstransformatoren.
Magnetfelder können Störsignale,
Bildwackeln sowie sonstige Störungen
verursachen.
• Débranchez le moniteur avant de le
nettoyer.
Le nettoyage d’un moniteur branché sur le
secteur vous expose à un choc électrique.
Pour les utilisateurs du système de
haut-parleurs i·Sound
concentrateur USB i·Station
option)
• Pour régler l’orientation du moniteur, ne
le tenez pas par les haut-parleurs ni par
le concentrateur USB.
Le système de haut-parleurs n’est pas conçu
pour supporter ces efforts qui pourraient le
casser ou causer des blessures.
Ô Ô
Ô
Ô Ô
ou du
ÔÔ
Ô
ÔÔ
(en
Autres
• N’installez pas le moniteur dans une zone
exposée à des champs magnétiques
puissants (par exemple près d’un hautparleur, à l’exception du système de hautparleurs i·Sound, ou d’un transformateur à
haute tension). Les champs magnétiques
peuvent entraîner des bruits, des distorsions
ou des tremblements de l’image.
• Sie erhalten normalerweise den besten
Sichtkomfort, wenn Sie den Monitor leicht
unterhalb der Augenhöhe positionieren.
Längere Bildschirmarbeit kann die Augen
belasten. Halten Sie daher ausreichende
Pausenzeiten ein. (Empfehlenswert ist eine
10minütige Pause pro Stunde.)
• Entfernen Sie die Abdeckung des
Netzanschlusses für die optionale i·Sound-
Lautsprechereinheit ausschließlich, um die
Lautsprechereinheit anzuschließen.
• Le meilleur confort visuel s’obtient souvent
en plaçant l’écran légèrement en dessous du
niveau des yeux. Un travail prolongé sur
écran peut entraîner une fatigue visuelle.
Veillez à prendre des pauses appropriées
(nous suggérons 10 minutes de pause par
heure).
• N’enlevez pas les protections des bornes
d’alimentation du système de haut-parleurs
i·Sound, sauf pour y brancher ce dernier.
PRECAUTIONS
xvii
PRECAUTIONS
E
IMPORTANT!
* This product has been
adjusted specifically for use in
the region to which it was
originally shipped. The
performance of the product,
(i.e. picture geometry, picture
positioning and color
convergence and purity in the
case of color monitors) is
optimally adjusted to the
earth's magnetic field of the
specific destination. If
operated outside the region to
which it was originally
shipped, the product may not
perform as stated in the
specifications.
xviii
* The manufacturer is not
responsible for damage or
malfunction caused by
improper connection. The
power cord should be
connected directly to a
standard wall power outlet.
PRECAUTIONS
SICHERHEITSHINWEISE
D
F
PRECAUTIONS
WICHTIG!
* Dieses Produkt wurde
werkseitig speziell für den
Einsatz am vorgesehenen
Bestimmungsort konfiguriert.
Die Monitorleistung (d. h.
Bildgeometrie, Bildposition
sowie Farbkonvergenz und
Farbreinheit bei
Farbmonitoren) ist optimal
auf das Magnetfeld der Erde
am Einsatzort abgestimmt.
Wird das Gerät nicht am
vorgesehenen
Bestimmungsort betrieben,
sind Abweichungen von den
spezifizierten Gerätedaten
möglich.
* Der Hersteller übernimmt
keine Verantwortung für
Schäden oder
Funktionsstörungen, die auf
nicht ordnungsgemäß
durchgeführte
Anschlußarbeiten
zurückzuführen sind. Das
Netzkabel sollte direkt an
eine Standard-Wandsteckdose
angeschlossen werden.
IMPORTANT!
* Cet appareil a été réglé en
fonction du pays où il était
destiné à être livré. Les performances du moniteur (par
exemple géométrie et position
de l’image, convergence et
pureté des couleurs dans le cas
des moniteurs couleur)
dépendent de l’adaptation au
champ magnétique terrestre
du pays de destination. En cas
d’utilisation en dehors de ce
dernier, il est possible que les
spécifications techniques
annoncées ne soient pas
respectées.
* Le fabricant ne peut être tenu
responsable des dégâts ou du
mauvais fonctionnement dus à
un branchement incorrect. Le
câble secteur doit être branché
directement à une prise
secteur murale standard.
PRECAUTIONS
xix
PRECAUTIONS
E
xx
PRECAUTIONS
INTRODUCTION
About This Manual
This manual explains the precautions, features, specifications, and
operation of your EIZO monitor. The separately bound 'Quick Setup
Guide' explains how to install your monitor, and how to implement basic
adjustments with the ScreenManager utility.
Package Contents:
• Monitor .................................................................. 1
• Power Cord ............................................................. 1
• User’s Manual ......................................................... 1
• Quick Setup Guide .................................................. 1
• Warranty Registration Card .................................... 1
• EIZO FlexScan CRT Utility Disk ............................ 1
• Sheet for the EIZO monitor information disk .......... 1
• If any of the above-listed items are missing or damaged, please contact
your local dealer for assistance.
• We recommend that you retain the original packing materials in case of
future need.
E
INTRODUCTION
5
1 FEATURES
Features
FlexScan® for wide compatibility
• 27 to 70 kHz horizontal scanning, 50 to 120 Hz vertical scanning
with automatic adjustment.
• The built-in microprocessor allows user-adjustable color control
adjustments to control screen distortion, and memorization of useradjusted settings.
• High resolution 1024 dots ´ 768 lines with flicker free 86 Hz (Max)
refresh rate.
High Resolution Color CRT
• 39 cm (15 inch) class, Actual Viewing Diagonal 35.0 cm (13.7 inches),
90° deflection, 0.28 mm screen pitch, high contrast, Flat Screen Type
CRT.
• Dynamic Beam Spot Control (D.B.S.C.) systems achieve both
brightness and sharp focus over the entire screen.
• S/S DY (saddle/saddle deflection yoke) prevents interference between
two or more monitors that are close together (allow approximately
15 cm distance between the monitors to avoid interference).
Ecological & Ergonomic Design
• Anti-Reflective SuperErgoCoat® not only eliminates reflection of
ambient light, but also improves the focus level over the entire display
area, and reduces static electricity accumulation on the CRT surface.
6
• This model complies with TCO 95 (The Swedish Confederation of
Professional Employees) guidelines for low frequency electric fields,
magnetic fields, static electricity and visual ergonomic requirements.
Furthermore, this model is produced with concern for the
environment and contains no harmful substances in any of its
components.
• EIZO products conforms to the CE European directive which limits
EMI (Electromagnetic Interference) and EMS (Electromagnetic
Susceptibility/Immunity) and is unaffected by such fields created by
general office electrical equipment.
A declaration of conformity statement is printed on the inside of the
back cover of this manual.
1 FEATURES
Functions
Windows 95/98 Plug & Play .... Readme.txt in the EIZO Utility Disk
• This model complies with VESA DDC1/DDC2B standards and
supports the Plug & Play function proposed in Windows 95/98.
ScreenManager™......................... Quick Setup Guide & Pages 8-22
• ScreenManager allows the setting and adjustment of the displayed
image using the QuickSet™ Control Pad and intuitive graphic icons for
easy identification of each function.
Auto-Sizing Function ......................................... Quick Setup Guide
• The auto-sizing function lets the microprocessor calculate and
automatically adjust the screen size and position for the selected
display mode.
Customized Color Controls ................................................. Page 10
• Dynamic color control provides WYSIWYG (What You See Is What
You Get) color matching.
To meet individual preferences, two color modes are provided:
a Standard mode with selection of color temperature and a Custom
mode for adjustment of color tone.
PowerManager™.................................................................... Page 15
• The PowerManager function automatically reduces unnecessary
power consumption when the monitor is not in active use. This
function complies with the NUTEK specification, the VESA DPMS
system and the EPA ENERGY STAR Program1).
E
Maintenance Port
• The monitor is equipped with a maintenance port on the rear panel.
This is provided so that complementary products can be utilized.
ScreenManager Pro, a utility software kit (supplied as optional), is
available which allows screen color, convergence and various
geometric compensation adjustments to be made via a mouse through
a serial cable connected to the port and the PC.
Optional i·Sound™ speaker system ..................................... Page 23
• The EIZO i·Sound speaker system is available as an option for
multimedia applications.
Please contact EIZO dealers for more information.
1) As an ENERGY STAR Partner, EIZO NANAO CORPORATION has determined that this product
meets the ENERGY STAR guidelines for energy efficiency.
1 FEATURES
7
2 IMAGING ADJUSTMENT
- Screen menu -
All of the icons shown in the ScreenManager 'Screen' menu are described
below.
• Allow the monitor to stabilize for at least 30 minutes before making
image adjustments.
Brightness, Contrast, Size, Position
These functions are used to adjust the brightness, contrast, size and
position of the screen. For more information about how to adjust each
of them, please refer to the 'Quick Setup Guide', page 8.
Geometry, Tilt
Image distortion and/or tilting may be caused by the earth's magnetic
field. Use the 'Screen' menu’s geometry (Side-Pincushion, Side-Pin
Balance, Trapezoidal, Parallelogram) and/or tilt adjustment functions to
correct any distortion.
Image distortion and tilting may also be caused by a device that is
generating a magnetic field. If the above adjustments are not effective,
try the following approaches.
• Check to see if there are any nearby interfering electronic devices such
• It is sometimes possible to correct distortion or tilting by reorienting
2 IMAGING ADJUSTMENT
8
as another monitor, an electric motor, or a speaker (other than an
optional EIZO i·Sound speaker unit). If so, move the device or move
the monitor.
the monitor.
Moiré Reduction
What is moiré?
Moiré refers to an interference pattern of dark wavy lines on the
screen. It is not a defect, but rather an interference phenomenon
caused by the relationship between the phosphor layout and the
imaging signal. Moiré is often an indication of a good focus level.
Moiré is particularly noticeable when using a light-gray or everyother-dot pattern background. Although moiré can not be eliminated,
it can be reduced with the moiré reduction feature.
Moiré can be reduced in a variety of ways.
1) Adjust with the ScreenManager’s moiré reduction function.
Adjust so that moiré becomes almost unnoticeable. Before adjusting,
set the desktop to an every-other-dot pattern (see picture) so that
moiré will be visible. Following the adjustment, change to a different
desktop background to reduce moiré even further.
2) Change the horizontal and vertical dimensions.
Adjust the horizontal and vertical dimensions of the display area as
necessary to reduce moiré.
E
(Every-other-dot pattern)(Moiré)
3) Change the selected desktop or wallpaper pattern.
Use the PC software to change the desktop or wallpaper pattern. Any
solid color pattern is recommended. For detailed information on how
to change these patterns, refer to the documentation for the PC and
operating system.
• The screen image may shake slightly while the ScreenManager
moiré reduction function is ON. Switching the function OFF will
improve image stability and clarity at the expense of slightly greater
moiré.
2 IMAGING ADJUSTMENT
9
3 COLOR ADJUSTMENT
- Color menu -
Outline
EIZO monitors have incorporated two color adjustment mode, standard
and custom. The “Standard” mode allows the adjustment of the color
spectrum. The “Custom” mode allows extensive controls over the colors
of the displayed image on the screen.
All adjustments for either mode can be made quickly and easily through
the ScreenManager 'Color' Menu - offering a tool to create customized
color environment.
Please find the details of the color mode adjustment capabilities below:
Contents Application
Standard mode
Sets color temperature.
Temperature can be set from 4000K to
10000K, in 500K increments. (Additionally,
industry standard of 9300K is set as default.)
For routine work and
printing.
3 COLOR ADJUSTMENT
10
Custom mode
Sets color temperature.
Allows for specific adjustments to Red,
Green and Blue (R/G/B). This consists of
the Cutoff and Gain functions.
* The color adjustment spectrum may vary between monitors.
** A color calibrator can be used for even higher-precision color
adjustment.
• Each monitor is slightly different, if two monitors are set to the same
color temperature value (i.e. 6500K), they may not necessarily look
the same.
For use when high
precision color
adjustment is necessary
(i.e. when there is a need
to obtain identical colors
on multiple monitors* or
match the display color
with printout color**.)
Adjusting the Standard mode
• Users should allow at least 30 minutes for the monitor to stabilize
before setting the color adjustments or color matching.
Procedure
1) Go to the 'Color' menu.
2) Select the “Standard mode” setting from the 'Color mode' menu.
3) Select the 'Temperature' icon. A color temperature bar will appear.
4) Adjust the temperature by using the right or left Arrow keys.
5) Press the ENTER key to save the data.
E
C o l o r
T e m p r a t u r e
What is color temperature?
Color temperature is a method to measure the white color tone,
generally indicated in degrees Kelvin. At high temperatures the white
tone appears somewhat blue, while at lower temperatures it appears
somewhat red. Computer monitors generally give best performance
at high temperature settings.
5000K: Slightly reddish white. Often used in printing industry.
6500K: Warm-white tone, similar to white paper or daylight. This
temperature is good for video-image display.
9300K: Slightly bluish white. This is the default setting for your
EIZO monitor.
3 COLOR ADJUSTMENT
11
Adjusting the Custom mode
Cutoff and Gain adjustments
Monitors use red, green and blue (R, G, and B) to convey color
information. They use an additive method to combine different
amounts of the primary colors to produce a desired color. In other
words, monitors start with no light (black) and add percentages of
red, green and blue to make colors. White is usually produced by
adding the same amount of all three colors, where black is usually
produced by adding no color.
However, colors are not only determined by the balance but also the
intensities of R, G, and B (how bright they are) which we call Gain,
and the saturation of R, G and B (how vivid or dull they are) which
we call Cutoff.
• Users should allow at least 30 minutes for the monitor to stabilize
before setting the color adjustments or color matching.
• Before you attempt to change the colors, always start with the color
settings set to the "default settings" by using the 'Reset' function in
the ScreenManager 'Others' menu.
• If only a quick setting is required, that is close to the desired color,
but not exact, skip making any changes to the Cutoff adjustment
(step 4). If a precise match is desired, adjustment of the Cutoff
levels must be made. We recommend that for exact matching, use a
color calibrator.
Procedure
3 COLOR ADJUSTMENT
12
1) For optimum results, before beginning the custom color adjustment,
go to the 'Screen' menu and set the display to maximum brightness
and contrast. (Use the 'Screen' menu’s 'Brightness' and 'Contrast'
icons.)
2) Then, return to the 'Color' menu and select the 'Custom mode'
setting.
3) Set the color temperature.
a) Select the 'Temperature' icon from the sub menu.
b) Select the temperature as desired by moving the arrow keys in
any direction.
4) Adjust the Cutoff
Cutoff
The Cutoff adjustment is the most powerful adjustment. It alters
the starting point (the black level) and the ending point (the white
level). If the Cutoff level for color is raised or lowered, black,
white, and all levels between are raised or lowered by the same
degree.
Before adjusting the Cutoff, it is best to display a screen with a black
background (such as the DOS command screen).
a) Select 'Cutoff' icon. The screen shown on the left will appear.
b) Adjust each color until you can create a uniform black screen.
5) Adjust the Gain
Gain
The Gain adjustment has no effect on the starting point (the black
level). It changes only the ending point (the white level). The Gain
adjustment is used to fine tune the whites and light grays to a good
balance.
Before adjusting the Gain, it is best to display a screen image that has
a white or grayscale background, such as the operating window for
Windows.
a) Select 'Gain' icon. The screen shown on the left will appear.
b) Adjust each color until you can create a uniform white screen.
E
6) To register the adjustment, select the 'Save' icon and then press the
ENTER key. If the settings are not saved, all adjustments will be lost.
7) Finally, readjust the contrast in the 'Screen' menu to get the best
image clarity.
• If an inappropriate adjustment is made, corrections can be made by
repeating the above procedure starting from Step 3 (temperature
setting).
• The values shown in percentages (%) for both the Cutoff and Gain
adjustments represent the current level within the specific adjustment
only. They are available only as a reference tool. (To create a
uniform white or black screen, the percentages for each will probably
not be the same.)
3 COLOR ADJUSTMENT
13
• These diagram explains how the color curves were changed for the
best adjustment in steps 4 and 5.
Adjust the black level
so that the low end of
the curve for each
color (R,G,B) is equal
as see picture 2.
Adjust the white level so
that the high end of the
curve for each color
(R,G,B) is equal as see
picture 3.
This setup gives the best
color balance.
What is the relation between the color and the brightness adjustment?
Brightness uniformly adjusts the amount of light output for the entire
screen and its background. If it is increases too high the background
will become white, too low and many dark colors will not be
displayed. It affects all color controls.
Contrast varies the difference in light output from the lowest to the
highest screen intensities. It is the brightness adjustment for the video
signal area.
After making the color settings, readjust the contrast to get the best
definition and intensity of the colors for the displayed image.
3 COLOR ADJUSTMENT
14
4 POWER-SAVE SETUP
- PowerManager menu -
What is PowerManager?
The PowerManager feature automatically reduces the monitor’s
power consumption during idle periods, in accordance with the PCs
ScreenSaver software.
There are two PowerSaving modes in the EIZO PowerManager:
Mode 1 and Mode 2 (maximum reduction). Even if the monitor is in
a power saving mode, it will return to a normal display immediately
when the mouse or keyboard is operated.
The EIZO PowerManager functions comply with NUTEK, the VESA
DPMS standard, and the EPA’s Energy Star guidelines.
Power consumption:
In operation: up to 96 W (Max.)
PowerManager Mode 1: less than 10 W
(Power Indicator flashing green)
PowerManager Mode 2: less than 5 W (Power Indicator solid yellow)
E
• Do your part to conserve energy, turn off the monitor when your
finished using it. Complete energy use can only be stopped by
disconnecting the monitor from the power supply.
• When the monitor is in a power saving mode, the optional EIZO
i·Sound speaker unit will turn off.
4 POWER-SAVE SETUP
15
Set-up Procedure
Set the monitor’s power-save environment to match the PC’s ScreenSaver
software.
• For the PC setup, please refer to the user’s manuals for the PC and
graphics board.
There are two power-save settings for the monitor.
‘VESA DPMS’ system works with the VESA DPMS signal.
‘NUTEK’s system works with a screen saver software and Energy Saver
for Macintosh which blanks the screen (totally black screen).
Set the monitor to match the PC’s power-saving software, as follows.
Monitor setting for matching the PC:
PC PC Power saving Monitor setting
PC/AT and compatibles VESA DPMS (Signal) VESA DPMS
(VESA DPMS activated)
PC/AT and compatibles Windows NUTEK
(VESA DPMS (Control Panel/Desktop/
inactivated) ScreenSaver: “Blank Screen”
Macintosh Energy Saver NUTEK
ScreenSaver software NUTEK
After Dark/“Blank” settings
4 POWER-SAVE SETUP
16
VESA DPMS System
1) First, make the appropriate settings for the PC.
2) Then select ‘VESA DPMS’.
3) Set the delay period, which is the interval that the monitor will wait
after receiving a power-save signal from the PC, before entering into
Mode 1 or Mode 2.
VESA DPMS power-saving method
VESA DPMS utilizes four signals: ON, STANDBY, SUSPEND, and OFF.
The monitor detects these signals from the graphics board and executes
power-saving accordingly, as illustrated below.
E
4 POWER-SAVE SETUP
17
NUTEK System
1) First make the appropriate ScreenSaver settings (Macintosh/Energy
Saver) for the PC.
2) Then select ‘NUTEK’.
3) Set the delay time, which is the interval between the time that the
ScreenSaver (Macintosh/EnergySaver) blanks the screen and the time
that the monitor enters Mode 1.
4) Set the Mode 1 duration time which is the user definable time (0-60
minutes) before the monitor enters Mode 2.
NUTEK power-saving method
Mode 1 operates for a user-definable period in ‘Duration’ (in 0-60
minutes) before the monitor enters Mode 2. If the keyboard or the
mouse are not in use during this period, the monitor will then enter
PowerManager Mode 2.
4 POWER-SAVE SETUP
18
What is VESA DPMS?
The acronym VESA stands for “Video Electronics Standards
Association,” and DPMS stands for “Display Power Management
Signaling.” DPMS is a communication standard that PCs and
graphics boards use to implement power savings at the monitor side.
What is NUTEK?
NUTEK is the acronym for the “Swedish National Board for
Industrial and Technical Development,” an organization that works to
promote power-saving technologies.
What is Energy Star?
“Energy Star” is a set of power-saving guidelines issued by the U.S.
Environmental Protection Agency (EPA). The guidelines apply to PC
systems and peripherals.
E
4 POWER-SAVE SETUP
19
5 OTHER SETTINGS
- Others, Information and Language
menus -
All of the icons shown in the ScreenManager 'Others' menu are described
below.
Degaussing
The monitor automatically degausses every time the power is turned ON
and every time it is reactivated from the PowerManager power-saving
Mode 2. A degaussing function is provided in the ScreenManager for use
at other times. Note that the image vibrates slightly while degaussing is
in progress, but will return to normal when degaussing is completed.
• The degauss circuitry takes about 30 minutes to regain maximum
power following degaussing before it can work again.
5 OTHER SETTINGS
20
What is degaussing?
“Degaussing” refers to the process of removing magnetic-field effects
from the monitor. Operation of the monitor within a magnetic field
may adversely effect color purity. Degaussing can be used to correct
the problem.
Beep
Use this feature to set the beeper ON or OFF. If the beeper is ON, the
monitor will generate beep signals as shown below. If the beeper is OFF,
the monitor will not beep.
Short beep • ScreenManager item selected.
• ScreenManager parameter adjusted to minimum
or maximum limit.
Long beep • AUTO-SIZING button pressed.
• ScreenManager data-save executed.
Four short beeps • Monitor not connected correctly.
• PC turned off.
• Monitor received unsupported signal frequency.
Menu Position, Menu Contrast
Use these functions to adjust the position, contrast and brightness of the
ScreenManager menu. When adjusting color, it is useful to adjust the
contrast and brightness of the ScreenManager menu according to the
background.
Reset
Use this function to return all ScreenManager parameters (size, position,
geometry, color, PowerManager etc.) to their factory default settings.
Default settings are as follows.
E
• Screen: Moiré = OFF
• Color: Standard/9300K
• PowerManager: VESA
• Others: Beep = ON
• Language: English
5 OTHER SETTINGS
21
Information status report
Use this feature to review the current ScreenManager settings. The menu
contains four pages. Pressing the ENTER key selects the different pages
in order. The information displayed on each page is as follows.
• Page 1: Input port, horizontal and vertical frequencies, moiré
reduction setting
• Page 2: Color-adjustment settings
• Page 3: PowerManager settings
• Page 4: Beep settings
Language menu
5 OTHER SETTINGS
22
Use this menu to select the ScreenManager language. Six languages are
available to choose from: English, German, French, Spanish, Italian and
Swedish. The menu text will appear in the language that is selected here.
6 GETTING THE MOST FROM
YOUR MONITOR
Adjustment Lock
The ScreenManager operation can be disabled by holding down the
AUTO-SIZING button while switching on the monitor’s power. This will
disable (“lock”) the ScreenManager and AUTO-SIZING button,
protecting from accidental changes. To unlock the buttons: switch the
power off, then hold down AUTO-SIZING button once again and turn
the power back on.
Note that brightness and contrast can be adjusted using the short cut
keys (see Quick Setup Guide page 6) even while the Control pad is
locked. After making such an adjustment, push the ENTER key to clear
the brightness/contrast adjustment menu from the screen.
Optional i·Sound™ speaker system
The optional speaker system i·Sound connects directly to the monitor and
can be used to support multimedia applications. The speaker also has a
microphone function. For details, consult EIZO dealers.
E
6 GETTING TH5 MOST FROM YOUR MONITOR
23
7 TROUBLESHOOTING
Troubleshooting
This page presents problems that can be corrected by the user. If a
problem persists even after applying the suggested remedies, contact an
EIZO dealer.
Problems
No picture
1) Indicator status: OFF
2) Indicator status: GREEN
3) Indicator status: YELLOW
Points to check with possible
solutions
• Check that the power cord is correctly connected.
• Try pressing a key on the keyboard, or clicking the
mouse. (The screen-saver software may be active.)
• Check brightness and contrast settings. Minimum
settings will cause screen to be blank.
• Try pressing a key on the keyboard, or clicking the
mouse. (The screen-saver software may be active.)
If the problem persists, switch off the monitor power
for a few minutes, then switch it back on and try
again.
4) “No signal detected” error
message appears.
7 TROUBLESHOOTING
24
• Check that the PC is switched ON.
• Check that the signal cable is properly connected to
the graphics board or PC.
• Check that the graphics board is correctly inserted
in the PC.
5) “Out of range” error
message appears.
(Example)
• Error messages will remain on the screen for 30 seconds, and then disappear. An
error message may not appear at all if the signal frequency is extremely high or
extremely low.
• Use the graphics board’s utility software to change
the frequency setting. (Refer to the manual of the
graphics board.)
• Whenever an error signal message appears, the
signal frequency will be displayed in red.
Imaging problems
E
1) Display size and/or position
is incorrect.
2) • The image vibrates on the
screen.
• A slight shaking movement
of the screen image or
text.
• Press the AUTO-SIZING button on the front panel.
See Quick Setup Guide, page 8.
• Adjust the image size and/or position using the
icons in the ScreenManager 'Screen' menu. See
page 10.
• Use of the “moiré reduction” feature may cause a
slight vibration. To eliminate the vibration, switch
the feature OFF or reduce the moiré reduction level.
See page 11.
• Check that the signal cable is properly connected to
the graphics board or PC.
• Check that the graphics board is correctly mounted
in the PC.
• The signal cable might be damaged. Please contact
the dealer.
• The monitor may be located close to a device that is
generating a magnetic field. Such devices include
speakers (other than the EIZO optional i·Sound
speaker), electric motors, high-voltage cables, and
other monitors. It may be solved by switching off
or moving the interfering device, or by relocating
the monitor.
7 TROUBLESHOOTING
25
• If the volume level of the EIZO optional i·Sound
speaker is too high, it may, in some cases, cause a
slight vibration. To eliminate, turn down the
volume of the speaker.
• A unstable signal from the graphics board may be the cause of the above problem
when using the monitor with a high resolution or in a high refresh mode. (The video
signal from the graphics board might be made irregular due to the use of a high
speed dot clock.) Change the resolution or the refresh rate to another setting.
3) The image is flickering.
Non-Interlaced / Interlaced
In a “non-interlaced” scan, the electric guns draw the entire image in one vertical
pass, with each pass covering every horizontal line.
In a “interlaced” scan, the guns draw the entire image by scanning vertically twice.
At the first scanning, the guns draw every other horizontal line. At the second, they
draw the other lines. Thus, in a "interlaced scan", the image flickers more visibly
when compared with a "non-interlaced" scan.
Flicker
The term “flicker” refers to noticeable shimmering that occurs when the image on
the screen is redrawn (“refreshed”) too slowly. A refresh rate of 80 Hz means the
image is redrawn 80 times per second. Most people will notice flicker at image
refresh rates as high as 60 or 70 Hz, whereas refresh rates of 72 Hz or above usually
is not noticeable. Flicker is known to be the cause of visual fatigue.
4) The screen is too bright or
too dark.
• Flicker will occur with interlaced scanning, or
non-interlaced scanning with a low refresh rate. All
EIZO monitors are capable of reproducing high
refresh rates for non-interlaced scanning. If a
problem occurs when using a non-interlaced signal,
try adjusting the graphics board to increase the
refresh rate (if possible). Refer to the graphics
board manual for information.
• Adjust the contrast and brightness using the
ScreenManager’s Screen menu.
See page 10.
5) Moiré patterns are
distracting.
7 TROUBLESHOOTING
26
• Go to the ScreenManager’s Screen menu. Switch on
the moiré reduction feature and adjust as necessary.
See page 11.
Color problems
1) The entire screen appears
bluish or reddish.
• The CRT is not warmed up. Allow 30 minutes for
E
the monitor to stabilize.
2) Color purity is not uniform.
Explanation of the Characteristics of CRTs
When the monitor is not fully warmed up, the screen may look slightly colored, e.g.
reddish or bluish. This phenomenon is due to the unstableness of the electron gun
during its warm-up period. Please wait for about 30 minutes until the monitor
stabilizes in order to gain its proper color.
• Allow 30 minutes for the monitor to warm up.
• Degauss the screen. (Use the degaussing feature in
the ScreenManager’s 'Others' menu. See page 22.)
Others
1) The monitor beeps or hums.
2) Control Pad “ENTER key”
does not operate.
• The monitor emits a humming noise when
executing automatic degaussing at power-ON.
This is not a problem.
• The monitor beeps at any time. This is not a
problem. See page 23 for full details.
• The Adjustment Lock is probably on. To unlock:
switch off the monitor power, then hold down the
AUTO-SIZING button and switch the monitor
back on. See page 25.
3) AUTO-SIZING button does
not operate.
• The Adjustment Lock is probably on. To unlock:
switch off the monitor power, then hold down the
AUTO-SIZING button and switch the monitor
back on. See page 25.
7 TROUBLESHOOTING
27
4) AUTO-SIZING button does
not work properly.
• A solid-color screen (i.e. red, green, blue) may appear for an instant while performing
the auto-sizing function, this phenomenon is not a failure.
• The Auto-sizing function is intended for use on the
Macintosh and on IBM compatibles running
Windows. It may not work properly if either of the
following applies.
- You are running an AT-compatible PC on
MS-DOS (not Windows).
- The background color for the “wallpaper” or
“desktop” pattern is set to black.
• Some signals from graphics boards may not
function properly.
5) Characters are too large.
What is Resolution?
Resolution is expressed as the number of dots (pixels) displayed on the screen. A
larger number of dots produces a more sharply defined (a higher-resolution) image.
Note that for a given screen size the dot size decreases as the number of dots
increases: a 640 x 480 (dot x line) resolution uses larger pixels than a 1024 x 768
resolution. The display size of a given font therefore varies according to the
resolution. Higher resolutions allow you to display more information on the screen.
Changing the resolution
If you are using a Macintosh, you can change the resolution from the APPLE menu by
selecting “Option” from “Monitor” or “Sound & Display.” If you are using a PC
other than a Macintosh, refer to the manual for your PC or graphics board for
information. Please refer to both the graphics board and monitor manuals for the
scanning frequency compatibility.
• Change the resolution of the graphics board to a
higher setting. (Refer to the manual for the
graphics board or PC.)
7 TROUBLESHOOTING
28
8 CLEANING
Cabinet
WARNING
• Keep liquids away from the monitor.
Spillage into the cabinet may result in fire, electric shock, or
equipment damage.
If an object or liquid falls/spills into the cabinet, unplug the monitor
immediately. Have the unit checked by a qualified service engineer
before using it again.
Using the monitor in this condition could cause serious injury or
equipment damage.
CAUTION
• To ensure safety, always unplug the monitor before cleaning it.
Failure to do so may result in electric shock.
• Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
• Never use thinner, benzene, alcohol (ethanol, methanol, or
isopropyl alcohol), abrasive cleaners, or other strong solvents,
as these may cause damage to the cabinet or CRT.
Periodic cleaning is recommended to keep the monitor looking new and
to prolong its operational lifetime. Clean the cabinet and CRT areas as
follows.
To remove stains, wipe the cabinet with a soft, lightly moistened cloth
using a mild detergent. Do not spray wax or cleaner directly onto the
cabinet.
E
CRT Surface
The CRT surface can be cleaned with a soft cloth, such as, cotton, or lens
paper.
If necessary, stubborn stains can be removed by moistening part of a
cloth with water to enhance its cleaning power.
8 CLEANING
29
9 SPECIFICATIONS
Electrical Specifications
CRT Dot Pitch 0.28 mm
CRT Size 39 cm (15 inch) class
CRT Surface Anti-Reflective SuperErgoCoat
90° deflection FS type
Scan Frequency
Horizontal: 27 kHz-70 kHz (Automatic)
Vertical: 50 Hz-120 Hz (Automatic)
Max. Active Display Area 280 mm (H) x 210 mm (V) (11.0" (H) x 8.2" (V))
(Viewable image size: 350 mm (13.7"))
* Display size can be set by the user through
microprocessor control panel.
* The actual size displayed can be dependent on the
graphics board or PC utilized.
Power Supply 100-120 VAC±10%, 50/60 Hz, 1.2 A
220-240 VAC±10%, 50 Hz, 0.6 A
Power Consumption
Normal: 82 W
Max.: 96 W (EIZO optional speaker attached: 99 W)
PowerManager Mode 1: Less than 10 W
PowerManager Mode 2: Less than 5 W
Input Connector Signal cable with D-Sub mini 15-pin connector
(permanently attached)
Recommended Resolution 1024 dots x 768 lines
Input Signal
Sync: • H/V Separate, TTL, Positive/Negative
• H/V Composite, TTL, Positive/Negative
• H/V Composite, Sync on Green 0.3 Vp-p, Negative
Video: • RGB Separate, Analog 0.7 Vp-p/75 Ohm, Positive
• RGB Separate, Analog plus Composite Sync on
Green
Mechanical Specifications
Dimensions 365 mm (W) x 375 mm (H) x 410 mm (D)
(14.4" (W) x 14.8" (H) x 16.1" (D))
Weight 14.5 kg (32.0 lbs)
®
Environmental Specifications
Temperature operating: 0°C to 40°C (32°F to 104°F )
Humidity 30% to 80% R.H. Non-condensing
storage: -20°C to 60°C (-4°F to 140°F )
Certifications and Standards
100-120 VAC range UL/CSA, FCC-B, DHHS, TÜV Rheinland/
220-240 VAC range CE, CB, TÜV Rheinland/GS,
9 SPECIFICATIONS
30
Ergonomics Approved, TCO’95,
EPA ENERGY STAR
TÜV Rheinland/Ergonomics Approved, TCO’95,
EPA ENERGY STAR
®
Program
®
Program
APPENDIX
Pin Assignment
Pin-Belegung
Affectation des Broches
D-Sub mini 15 pin connector
Pin No. Signal Pin.No. Signal
1 Red video 9 No pin
2 Green video 10 Ground
3 Blue video 11 (shorted)
4 Ground 12 Data
5 No pin 13 H.Sync
6 Red ground 14 V.Sync
7 Green ground 15 Clock
8 Blue ground
100
APPENDIX
Timing Charts
Timing-Übersichten
Synchronisation des Signaux
Based on the signal diagram shown below, 4 factory presets have been
registered in the monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt 4 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
4 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
A Front Porch Vordere Schwarzschulter Front avant
B Sync Period Synchronimpuls Délai de
C Back Porch Hintere Schwarzschulter Front arrière
D Blanking Period Austastzeit Délai de clignotement
E Display period Display-Zeit Délai d'affichage
F Total cycle Kompletter Zyklus Cycle total
S Sync signal level Sync-Signalpegel Niveau du signal de
V Video signal level Video-Signalpegel Niveau du signal vidéo
A
synchronisation
synchronisation
The sync pulse, for both the horizontal and vertical signals, has positive or
negative polarity combination (as shown following) to encode different
modes.
Der Sync-Impuls für Horizontal- und Vertikalsignale weist eine kombinierte
(d. h. eine positive und negative) Polarität auf (siehe unten). Auf diese
Weise ist eine Codierung der verschiedenen Betriebsarten möglich.
L’impulsion de synchronisation, pour les signaux horizontaux et verticaux,
a une combinaison de polarités positives ou négatives (présentée page
suivante) qui permet de coder différents modes.
APPENDIX
101
VGA (text)
T 720 dots x 400 lines mode
Frequencies: fd/28.322MHz, fH/31.468kHz, fV/70.087Hz
Interlace: Non
Sync Polarity: H/Negative, V/Positive
Video Signal Level: 0.7Vp-p/75Ohm
VESA
T 1024 dots x 768 (85Hz) lines mode
Frequencies: fd/94.5MHz, fH/68.68kHz, fV/84.99Hz
Interlace: Non
Sync Polarity: H/Negative, V/Negative
Video Signal Level: 0.7Vp-p/75Ohm
Unit A B C D E F
H
V
H
V
µs 0.636 3.813 1.907 6.356 25.422 31.778
Dot 18 108 54 180 720 900
ms 0.381 0.064 1.111 1.556 12.712 14.268
Line 12 2 35 49 400 449
Unit A B C D E F
µs 0.508 1.016 2.201 3.725 10.836 14.561
Dot 48 96 208 352 1024 1376
ms 0.015 0.044 0.524 0.583 11.183 11.766
Line 1 3 36 40 768 808
Apple Macintosh
APPENDIX
102
T 640 dots x 480 lines mode
Unit A B C D E F
H
V
Frequencies: fd/30.24MHz, fH/35.00kHz, fV/66.67Hz
Interlace: Non
Sync Polarity: Separate sync, TTL, Negative
Video Signal Level: 0.7Vp-p/75Ohm
µs 2.116 2.116 3.175 7.407 21.164 28.571
Dot 64 64 96 224 640 864
ms 0.086 0.086 1.114 1.286 13.714 15.000
Line 3 2 39 45 480 525
T 832 dots x 624 lines mode
H
V
Frequencies: fd/57.28MHz, fH/49.73kHz, fV/74.55Hz
Interlace: Non
Sync Polarity: Separate sync, TTL, Negative
Video Signal Level: 0.7Vp-p/75 Ohm
Dimensions
Abmessungen
Dimensions
Unit A B C D E F
µs 0.559 1.115 3.910 5.586 14.524 20.111
Dot 32 64 224 320 832 1152
ms 0.020 0.060 0.784 0.865 12.549 13.414
Line 1 3 39 43 624 667
A
mm (inches)
APPENDIX
103
Congratulations! You have just purchased a TCO’95 approved and labelled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to
reducing the burden on the environment and also, to the further development of environmentally adapted
electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging the
adaptation of goods and services to the environment. The main problem, as far as computers and
other electronics equipment are concerned, is that environmentally harmful substances are used
both in the products and during the manufacturing. Since it has not been possible for the majority of
electronics equipment to be recycled in a satisfactory way, most of these potentially damaging
substances sooner or later enter Nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Since all methods of conventional electricity generation have a negative effect on the environment
(acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to conserve energy.
Electronics equipment in offices consume an enormous amount of energy since they are often left
running continuously.
What does labelling involve?
This product meets the requirements for the TCO’95 scheme which provides for international and
environmental labelling of personal computers. The labelling scheme was developed as a joint effort
by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsföreningen (The
Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and
Technical Development in Sweden).
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of
electrical and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands concern restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other
things. The product must be prepared for recycling and the manufacturer is obliged to have an
environmental plan which must be adhered to in each country where the company implements its
operational policy.
The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The
length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the reduction
of electric and magnetic fields, physical and visual ergonomics and good usability.
You will find a brief summary of the environmental requirements met by this product on the
next page. The complete environmental criteria document may be ordered from:
TCO Development Unit
S-114 94 Stockholm
Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO’95 approved and labelled products may also be obtained
via the Internet, using the address:
http://www.tco-info.com/
TCO’95 is a co-operative project between
Environmental Requirements
Brominated flame retardants
Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings.
In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist
of flame retardant substances. These are related to another group of environmental toxins, PCBs,
which are suspected to give rise to similar harm, including reproductive damage in fisheating birds and
mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood
and researchers fear that disturbances in foetus development may occur.
TCO’95 demand requires that plastic components weighing more than 25 grams must not contain
organically bound chlorine and bromine.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
TCO’95 requirement permits the inclusion of lead since no replacement has yet been developed.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of cadmium. The colour-generating layers of display screens must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system
and is toxic in high doses.
TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million)
of mercury. It also demands that no mercury is present in any of the electrical or electronics components
concerned with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of
expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased
risks of skin cancer (malignant melanoma).
The relevant TCO’95 requirement: Neither CFCs nor HCFCs may be used during the
manufacturing of the product or its packaging.
*
Bio-accumulative is defined as substances which accumulate within living organisms.
**
Lead, Cadmium and Mercury are haevy metals which are Bio-accumulative.
For U.S.A, Canada, etc. (100-120 Vac) Only
WARNING!
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provided
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
*Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified shielded cable with this monitor below so as to keep interference
within the limits of a Class B digital device.
-AC Cord
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach ZH1/618/10.80 mit dem ideosignal,
1024 Punkte x 768 Zeilen, RGB analog, 0,7Vp-p und mindestens 85,0Hz Bildwiederholfrequenz, non
interlaced.
Die Übereinstimmung mit den Ergonomie-Vorschriften ZH1/618 kann nur dann garantiert werden,
wenn dieser Monitor mit den Werkseinstellungen verwendet wird.
Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Lärmemission kleiner 70dBA laut ISO 7779.
PTB Note
Eigensichere Kathodestranlröhre nach Anlage III Röntgenverordnung. Die in diesem Geraet entstehende
Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend abgeschirmt.
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit
dem Partner von Roll MBB Recycling GmbH.
Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden.
Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende
Rufnummber: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:
www.eizo.de.
Hinweis
Die Bildroehre dieses Monitors is frei von Cadmium.
Loading...