Eizo EV2450, EV2455 User Guide

User’s Manual

Color LCD Monitor

Important

Please read PRECAUTIONS, this User’s Manual, and the Setup Guide (separate volume) carefully to familiarize yourself with safe and effective usage.

• Please refer to the Setup Guide for basic information ranging from connection of the monitor to a PC to using the monitor.

• The latest User’s Manual is available for download from our web site:

www.eizoglobal.com

Location of Caution Statement

This product has been adjusted specically for use in the region to which it was originally shipped. If operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation. EIZO Corporation is under no obligation to hold any submitted material or information condential unless prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO monitor specications are subject to change without notice.

- 2 -

Notice for this monitor

This product is suited to general purposes like creating documents, viewing multimedia content.

This product has been adjusted specically for use in the region to which it was originally shipped. If the product is used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

· Power cords provided with the product

· Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and maintain a stable display.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for extended periods of time.

If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To maximize the life of the monitor, we recommend the monitor be turned off periodically.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer to “Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994% or higher.

The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker, please contact your local EIZO representative.

- 3 -

Notice for this monitor

Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The symptom may disappear.)

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do not attempt to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the monitor.

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

Note

• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.

The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

- 4 -

CONTENTS

Notice for this monitor ................................................................................3

Cleaning ................................................................................................................4

To use the monitor comfortably .........................................................................4

CONTENTS ....................................................................................................5

Chapter 1 Introduction ..............................................................................7

1-1. Features .....................................................................................................7

1-2. Controls and Functions ...........................................................................9

Front ............................................................................................................9

●

Rear ...........................................................................................................10

●

1-3. Supported Resolutions ..........................................................................11

EV2450......................................................................................................11

●

EV2455......................................................................................................12

●

1-4. Setting the Resolution ...........................................................................13

Windows 8.1 / Windows 8 / Windows 7.....................................................13

●

Windows Vista ...........................................................................................13

●

Mac OS X ..................................................................................................13

●

Chapter 2 Basic Adjustment/Setting ..................................................... 14

2-1. Switch Operation Method ......................................................................14

2-2. Switching Input Signals .........................................................................15

2-3. Switching Display Modes (Color Modes) .............................................16

Display Modes ...........................................................................................16

●

2-4. Conserving Energy ................................................................................. 17

2-5. Adjusting Brightness .............................................................................20

2-6. Adjusting Volume....................................................................................21

Chapter 3 Advanced Adjustment/Setting .............................................22

3-1. Basic Operation of the Setting menu ...................................................22

3-2. Setting Menu Functions .........................................................................23

Color Adjustment .......................................................................................23

●

Signal Settings ..........................................................................................26

●

Preference Settings ................................................................................. 30

●

Language ..................................................................................................32

●

Information ................................................................................................32

●

Chapter 4 Administrator Settings ..........................................................33

4-1. Basic Operation of the “Administrator Settings” Menu .....................33

4-2. Functions of the “Administrator Settings” Menu .............................. 34

Chapter 5 Troubleshooting ..................................................................... 36

5-1. No picture ................................................................................................36

5-2. Imaging problems (for both digital and analog)..................................38

5-3. Imaging problems (for analog only) .....................................................39

5-4. Other problems ...................................................................................... 40

Chapter 6 Reference ............................................................................... 41

6-1. Attaching the Optional Arm ................................................................... 41

6-2. Detaching/Attaching Stand Base ..........................................................42

6-3. Attaching/Detaching the Cable Holder ............................................... 46

6-4. Connecting Multiple PCs ...................................................................... 48

6-5. Making Use of USB (Universal Serial Bus) ......................................... 49

Required System Environment .................................................................49

●

Connection Procedure (Setup of USB Function) ......................................49

●

6-6. Specications ........................................................................................ 50

Outside Dimensions ................................................................................. 54

●

Main Default Settings ............................................................................... 56

●

Accessories .............................................................................................. 56

●

6-7. Preset Timings ........................................................................................57

Chapter 7 Glossary .................................................................................59

Appendix ..................................................................................................... 62

Trademark ...........................................................................................................62

License / Copyright ............................................................................................62

- 5 -

ENERGY STAR ....................................................................................................63

TCOCertied ......................................................................................................63

FCC Declaration of Conformity ........................................................................65

LIMITED WARRANTY .........................................................................................67

Recycling Information ...................................................................................... 68

CONTENTS

- 6 -

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

• 23.8″ wide format LCD (EV2450)

• 24.1″ wide format LCD (EV2455)

• Supports a resolution of 1920 × 1080 (EV2450)

• Supports a resolution of 1920 × 1200 (EV2455)

• IPS panel with 89˚ horizontal and vertical viewing angles

• Supports four digital signal input interfaces (DisplayPort (HDCP) × 1, HDMI TypeA (HDCP) × 1, DVI-D (HDCP) × 1, and D-Sub mini 15-pin × 1)

- DisplayPort (8-bit support)

The DisplayPort input receives both image signals and audio signals via a single DisplayPort cable.

*1 When transmitting an audio signal using the DisplayPort cable, the graphics board must support audio output.

See “6-6. Specications” (page 50).

- HDMI

Supports PC signals via HDMI input. The HDMI input receives both image signals and audio signals via a single HDMI cable.

• The Color Mode function allows the user to select the display mode optimum to the displayed image.

The Paper mode reproduces a printed paper effect on the monitor. In Paper mode, the amount of blue light emitted from the screen is reduced by changing the color tone and controlling the brightness.

See “2-3. Switching Display Modes (Color Modes)” (page 16).

• Power saving functions

Suppressing power consumption*2 reduces carbon dioxide emissions. This product is equipped with power saving functions.

- 0 W power consumption when the main power is off

Equipped with a main power switch. When not using the monitor, you can turn off the main power supply so that the power is cut completely.

- Auto EcoView

The ambient light sensor on the front of the monitor detects the ambient brightness to automatically adjust the screen brightness to a comfortable level. Excessively high brightness may increase power consumption and cause unwanted environmental effects. It may also lead to eye fatigue. The range of automatic adjustment can be congured to personal preference.

See “Auto EcoView” (page 18).

- EcoView Optimizer 2

The monitor automatically adjusts the screen brightness according to the white level of the input signal. This function can reduce power consumption while maintaining the brightness specied by the input signal.

See “EcoView Optimizer 2” (page 18).

Chapter 1 Introduction

- 7 -

Chapter 1 Introduction

- EcoView Sense

The sensor on the front of the monitor detects user movement. When the user moves away from the monitor, the monitor shifts to power saving mode automatically and does not display images on the screen in order to reduce power consumption. The sensitivity of the sensor and time until power saving mode is activated can be set according to the monitor usage environment and movement of the user.

See “EcoView Sense” (page 19).

*2 Reference values:

EV2450 Maximum power consumption: 44 W (when a USB device is connected, speaker working), standard power consumption: 11 W (brightness 120 cd/m device is connected, speaker not working, at default settings) EV2455 Maximum power consumption: 49 W (when a USB device is connected, speaker working), standard power consumption: 13 W (brightness 120 cd/m device is connected, speaker not working, at default settings)

, when no USB

• Equipped with a USB Hub function that supports USB 3.0

Achieves high-speed data transfers of up to 5 Gbps, which enables transfers of large amounts of data to and from USB-connected devices in a short amount time.

See “6-5. Making Use of USB (Universal Serial Bus)” (page 49).

• High degree of exibility for installation

- Stand with wide range of movement. The monitor can be adjusted to a position that provides a comfortable and less tiring work environment.

Tilt: 35˚ up/5˚ down, swivel: 344˚, vertical rotation: 90˚ left/90˚ right, adjustable height: 114.7 mm (tilt: 35˚) / 140 mm (EV2450), 131 mm (EV2455) (tilt: 0˚)

- A thin bezel provides a virtually seamless viewing experience in multiple monitor environments. Mounting the monitor on an arm allows the screen to be installed rotated by 180˚ (ipped vertically).

Installation example

• The orientation of the Setting menu can be changed when using the monitor screen in the portrait display position (see “Menu Rotation” (page 30)).

• Displays HDCP (High-bandwidth Digital Protection) *3 protected contents.

*3 Supports HDCP Version 1.x

• Supports the “ScreenManager Pro” software for adjusting the screen using the mouse and keyboard

This software can be downloaded from our web site (www.eizoglobal.com).

• Supports the “EIZO Monitor Congurator” software for creating monitor conguration les

When installing multiple units of this monitor, this software allows users to apply a single conguration le to all monitors at the same time. This increases the efciency of monitor installation work by eliminating the need for conguring each monitor individually. For more information, refer to our web site (www.eizoglobal.com).

- 8 -

1-2. Controls and Functions

Front

●

Chapter 1 Introduction

Setting menu

1. EcoView Sense sensor Detects user movement in front of the monitor (EcoView Sense function (page 19)).

2. Ambient light sensor Detects ambient brightness (Auto EcoView function (page 18)).

3. Operation switches Displays menus. Operate the switches according to the operation guide.

4. Power switch Turns the power on or off.

5. Power indicator Indicates the monitor’s operation status.

White: Screen display Orange: Power saving mode OFF: Main power / power off

*1 For details on usage, see “3-1. Basic Operation of the Setting menu” (page 22).

- 9 -

Rear

●

Chapter 1 Introduction

11 12 13

6 7 8

6. Main power switch Turns the main power on or off.

7. Power connector Connects the power cord.

8. Input signal connectors The following connectors are available on the monitor rear in order of left to right.

D-Sub mini 15-pin connector DisplayPort connector HDMI connector DVI connector

9. Handle This handle is used for transportation

10. USB downstream port Connects to a peripheral USB device.

11. USB upstream port Connects to the USB cable when using software that needs a USB connection, or when using the USB Hub function.

12. Headphone jack Connects to headphones.

13. Stereo mini jack Connects to a stereo mini jack cable.

14. Security lock slot Complies with Kensington’s MicroSaver security system.

15. Speakers Outputs audio.

16. Stand

17. Cable holder

*2 An optional arm (or optional stand) can be attached by removing the stand section (see “6-1. Attaching the Optional Arm” (page 41)). *3 For the cable holder attachment procedure, see “6-3. Attaching/Detaching the Cable Holder” (page 46).

Adjusts the height and angle (tilt, swivel, and rotation) of the monitor. Holds the monitor cables.

- 10 -

1-3. Supported Resolutions

The monitor supports the following resolutions.

EV2450

●

Chapter 1 Introduction

Resolution

640 × 480 VGA/CEA-861 59.94 Hz Progressive √ √ √ √ 640 × 480 CEA-861 60 Hz Progressive √ √ - √ 640 × 480 VESA 72.81 Hz / 75 Hz Progressive - - - √ 720 × 400 VGA TEXT 70.09 Hz Progressive √ √ √ √

720 × 480 (4:3) CEA-861 59.94 Hz / 60 Hz Progressive √ √ - -

720 × 480 (16:9) CEA-861 59.94 Hz / 60 Hz Progressive √ √ - -

720 (1440) × 480 (4:3) CEA-861 59.94 Hz / 60 Hz Interlaced - √ - -

720 (1440) × 480 (16:9) CEA-861 59.94 Hz / 60 Hz Interlaced - √ - -

720 × 576 (4:3) CEA-861 50 Hz Progressive - √ - -

720 × 576 (16:9) CEA-861 50 Hz Progressive - √ - -

720 (1440) × 576 (4:3) CEA-861 50 Hz Interlaced - √ - -

720 (1440) × 576 (16:9) CEA-861 50 Hz Interlaced - √ - -

800 × 600 VESA 56.25 Hz / 72.19 Hz / 75 Hz Progressive - - - √

800 × 600 VESA 60.32 Hz Progressive √ √ √ √ 1024 × 768 VESA 60 Hz Progressive √ √ √ √ 1024 × 768 VESA 70.07 Hz / 75.03 Hz Progressive - - - √ 1280 × 720 CEA-861 50 Hz Progressive - √ - 1280 × 720 CEA-861 59.94 Hz Progressive √ √ - 1280 × 720 CEA-861 60 Hz Progressive √ √ √ √ 1280 × 800 VESA CVT 59.81 Hz Progressive √ √ √ √

1280 × 1024 VESA 60.02 Hz Progressive √ √ √ √ 1280 × 1024 VESA 75.03 Hz Progressive - - - √

1600 × 900 VESA RB 60 Hz Progressive √ √ √ √ 1680 × 1050 VESA CVT 59.95 Hz Progressive √ √ √ √ 1680 × 1050 VESA CVT RB 59.88 Hz Progressive √ √ √ √

1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080

*1 Recommended resolution

Applicable

Signals

CEA-861 50 Hz / 59.94 Hz / 60 Hz Interlaced - √ - CEA-861 50 Hz Progressive - √ - CEA-861 59.94 Hz Progressive √ √ - CEA-861 60 Hz Progressive √ √ √ √

Vertical Scan

Frequency

Scan Typ e DisplayPort HDMI DVI D-Sub

- 11 -

EV2455

●

Chapter 1 Introduction

Resolution

720 × 480 (4:3) CEA-861 59.94 Hz / 60 Hz Progressive √ √ - -

720 × 480 (16:9) CEA-861 59.94 Hz / 60 Hz Progressive √ √ - -

720 (1440) × 480 (4:3) CEA-861 59.94 Hz / 60 Hz Interlaced - √ - -

720 (1440) × 480 (16:9) CEA-861 59.94 Hz / 60 Hz Interlaced - √ - -

720 × 576 (4:3) CEA-861 50 Hz Progressive - √ - -

720 × 576 (16:9) CEA-861 50 Hz Progressive - √ - -

720 (1440) × 576 (4:3) CEA-861 50 Hz Interlaced - √ - -

720 (1440) × 576 (16:9) CEA-861 50 Hz Interlaced - √ - -

800 × 600 VESA 56.25 Hz / 72.19 Hz / 75 Hz Progressive - - - √

1280 × 1024 VESA 60.02 Hz Progressive √ √ √ √ 1280 × 1024 VESA 75.03 Hz Progressive - - - √

1600 × 900 VESA RB 60 Hz Progressive √ √ √ √

1600 × 1200 VESA 60 Hz Progressive √ √ √ √ 1680 × 1050 VESA CVT 59.95 Hz Progressive √ √ √ √ 1680 × 1050 VESA CVT RB 59.88 Hz Progressive √ √ √ √ 1920 × 1080 CEA-861 50 Hz / 59.94 Hz / 60 Hz Interlaced - √ - 1920 × 1080 CEA-861 50 Hz Progressive - √ - 1920 × 1080 CEA-861 59.94 Hz Progressive √ √ - -

1920 × 1080 CEA-861 60 Hz Progressive √ √ √ √ 1920 × 1200 1920 × 1200

*1 Recommended resolution

Applicable

Signals

VESA CVT 59.89 Hz Progressive - - - √

VESA CVT RB 59.95 Hz Progressive √ √ √ √

Vertical Scan

Frequency

Scan Typ e DisplayPort HDMI DVI D-Sub

- 12 -

1-4. Setting the Resolution

If the resolution is incorrect after connecting the monitor to a PC or if you want to change the resolution, follow the procedure below.

Windows 8.1 / Windows 8 / Windows 7

●

1. For Windows 8.1 / Windows 8, click the “Desktop” tile on the Start Screen to display the desktop.

2. Right-click the mouse anywhere on the desktop except for icons.

3. From the displayed menu, click “Screen resolution”.

4. On the “Screen Resolution” dialog box, select the monitor.

5. Click “Resolution” to select the desired resolution.

6. Click the “OK” button.

7. When a conrmation dialog box is displayed, click “Keep changes”.

Windows Vista

●

1. Right-click the mouse anywhere on the desktop except for icons.

2. From the displayed menu, click “Personalize”.

3. On the “Personalization” window, click “Display Settings”.

4. On the “Display Settings” dialog box, select the “Monitor” tab and select the desired resolution in the “Resolution” eld.

5. Click the “OK” button.

6. When a conrmation dialog box is displayed, click “Yes”.

Chapter 1 Introduction

Mac OS X

●

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select the desired resolution in the “Resolutions” eld.

4. Your selection will be reected immediately. If you are satised with the selected resolution, close the window.

- 13 -

Chapter 2 Basic Adjustment/Setting

This monitor enables users to change the brightness according to personal preference or to suit the usage environment and reduce power consumption to conserve energy.

This chapter describes the basic functions that can be adjusted and set using the switches on the front of the monitor. For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced Adjustment/Setting” (page 22).

2-1. Switch Operation Method

Displaying the operation guide

1. Touch any switch (except ).

The operation guide appears on the screen.

Adjusting/setting

1. Touch a switch for adjustment/setting.

The Adjustment/Setting menu appears. (A submenu may also be displayed. In this case, select the item for adjustment/setting using

2. Perform adjustment/setting with the switches and select to accept the changes.

Exiting

1. Select or to exit the menu.

2. When no menu is displayed, the operation guide will automatically disappear after a few seconds if no switches are operated.

and select .)

- 14 -

2-2. Switching Input Signals

When a monitor has multiple signal inputs, the signal to display on-screen can be changed.

Chapter 2 Basic Adjustment/Setting

- 15 -

Chapter 2 Basic Adjustment/Setting

2-3. Switching Display Modes (Color Modes)

This product is preinstalled with color modes for various display purposes. Switch the mode according to the purpose and content for display. This allows the monitor to display images in a manner appropriate to the display content.

Display Modes

●

Color Mode Purpose

User1 User2

sRGB

Paper

Movie DICOM

Select either of these modes to set a user-dened display mode.

This mode is suitable for matching color reproduction with peripheral devices that support sRGB, such as when printing photos taken using a digital camera.

This mode uses color tones and contrast similar to that of paper to produce a printed paper effect. It is suitable for displaying images from media such as books and documents.

This mode displays moving images brightly and with a clear-cut three-dimensional appearance. It is suitable for playing back video content. Selected for the display in the DICOM mode.

Note

• “ScreenManager Pro” allows you to select the color mode automatically according to the application in use. (“ScreenManager Pro” is software for adjusting the screen using the mouse and keyboard. This software can be downloaded from our web site (www.eizoglobal.com).)

- 16 -

Chapter 2 Basic Adjustment/Setting

2-4. Conserving Energy

This monitor is equipped with EcoView functions to enable users to conserve energy. Use this function to curtail unnecessary power consumption and save on electricity expenses. Saving power also reduces carbon dioxide emissions.

Level of power saving

Note

• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the “EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher the power saving level attained.

- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness value.

- CO

Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2 emissions reduced when using the monitor for 1 hour.

* The numeric value is a result of calculation based on a default setting (0.000555 t -CO2/kWh) determined by a Japanese ministerial ordinance (2006, Ministry of Economy,

Trade and Industry, Ministry of Environment, civil code article 3) and may differ depending on country and year.

- 17 -

Function Setting Range Description Note

Auto EcoView On

Off

Advanced Settings

EcoView Optimizer 2 On

Maximum Minimum

Reset - Return the advanced settings to their default values. -

Brightness 0 to 100 Set the range for automatic brightness adjustment.

Ambient Light Bright

Standard

Dark

Off

The ambient light sensor on the front of the monitor detects the ambient brightness to automatically adjust the screen brightness to a comfortable level using the Auto EcoView function. The power consumption of the backlight can be curtailed by adjusting the brightness to an appropriate level. This function can also mitigate eye strain and tiredness caused by a screen that is too bright or too dark.

Use the “Advanced Settings” to set the automatic adjustment range to suit the monitor’s usage environment or personal preference.

By setting the maximum value and minimum value of the adjustment range in advance, the brightness will be adjusted automatically within the set range.

Using the default setting is recommended. (Default setting: “Bright” for maximum value, “Dark” for minimum value)

Chapter 2 Basic Adjustment/Setting

• Be careful not to block the ambient light sensor on the lower side of the monitor when using the Auto EcoView function.

• Even when the Auto EcoView setting is “On”,

the

the monitor or color adjustment can be used to change the “Brightness” to suit your personal preference. Moreover, the manner in which the Auto EcoView function changes brightness also differs according to the changed value.

• When “DICOM” is selected for the color mode, the Auto EcoView setting is turned “Off”.

• The maximum and minimum brightness values cannot be set to the same value.

• For details on the “Ambient Light” setting, refer to our web site (www.eizoglobal.com).

• The setting is turned “Off” in the following cases:

- When “Movie” or “DICOM” is selected for the color mode

• When set to “On”, the appearance of pale colors may change. If this bothers you, set this function to “Off”.

operation switch on the front of

- 18 -

Function Setting Range Description Note

EcoView Sense On

Off

Advanced Settings

Time 5, 30 sec

1, 3, 5, 10, 15, 30, 45, 60 min

Sensitivity Level 5

Level 4 Level 3 Level 2 Level 1

Reset - Return the advanced settings to their default values. -

When set to “On”, the sensor on the front of the monitor detects user movement. When the user moves away from the monitor, it automatically shifts to power saving mode and does not display images on the screen in order to reduce power consumption. When the user comes near the monitor again, it recovers from power saving mode and displays images.

The sensitivity of the sensor and time until power saving mode is activated can be set in the “Advanced Settings” according to the monitor usage environment and movement of the user.

Species the time from when the user leaves the monitor until the “No Presence detected” message appears. The monitor shifts to power saving mode about 20 seconds after the message is displayed.

When the setting level is high (“Level 5” at maximum), even minor movements of the user are detected, which prevents the monitor from readily shifting to power saving mode. On the other hand, when the setting level is low (“Level 1” at minimum), only major movements of the user are detected, which allows the monitor to readily shift to power saving mode.

Chapter 2 Basic Adjustment/Setting

• At the time of shifting to power saving mode, a message that indicates the transition is displayed.

• When “Power Save” on the Preferences menu is set to “Off”, the EcoView Sense setting is disabled.

• The EcoView Sense function is activated when the sensor on the front of the monitor detects the movement of heat. Therefore, the sensitivity should be changed depending on the typical user’s clothes or typical room temperature. If the monitor shifts to or recovers from power saving mode contrary to your expectations, try changing the setting level.

• To use the monitor comfortably, increase the sensitivity for high temperatures, because the detection sensitivity decreases. Reduce the sensitivity for low temperatures because the detection sensitivity increases.

- 19 -

Chapter 2 Basic Adjustment/Setting

2-5. Adjusting Brightness

The brightness of the screen can be adjusted to suit the installation environment or personal preference. The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD back panel).

Setting Range

0 to 100

Note

• When Auto EcoView is set to “On”, the adjustment range is restricted as follows. (For details on Auto EcoView, see “Auto EcoView” (page 18).)

- The brightness setting cannot be increased or decreased past the maximum and minimum brightness values specied in the advanced settings of Auto EcoView.

- Brightness may not be adjusted when the installation environment of the monitor is excessively bright or dark.

- 20 -

2-6. Adjusting Volume

The volume of the speakers and headphones can be set individually.

Setting Range

0 to 30

Chapter 2 Basic Adjustment/Setting

- 21 -

Chapter 3 Advanced Adjustment/Setting

This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu. For basic functions, see “Chapter 2 Basic Adjustment/Setting” (page 14).

3-1. Basic Operation of the Setting menu

Chapter 3 Advanced Adjustment/Setting

Menu display

1. Touch any switch (except ).

The operation guide appears.

2. Select .

The Setting menu appears.

Adjusting/setting

1. Select a menu to adjust/set with and select .

The Sub menu appears.

2. Select an item to adjust/set with and select .

The Adjustment/Setting menu appears.

3. Perform adjustment/setting with or and select to accept the changes.

The Sub menu appears. Selecting

setting and restore the state prior to making changes.

Exiting

1. Select .

The Setting menu appears.

2. Select .

The Setting menu quits.

during adjustment/setting will cancel the adjustment/

- 22 -

3-2. Setting Menu Functions

Color Adjustment

●

The color mode setting status can be adjusted according to personal preference.

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more after power to the monitor has been turned on before adjusting the monitor.

• The same image may be observed in different colors on multiple monitors due to monitor-specic characteristics. Make ne color adjustments visually when matching colors across multiple monitors.

Note

• Using “ScreenManager Pro” allows you to perform color adjustment with the mouse and keyboard on your PC. The adjusted state can also be saved and loaded as color data. “ScreenManager Pro” can be downloaded from our web site (www.eizoglobal.com).

Chapter 3 Advanced Adjustment/Setting

Color Mode

(Functions that can be adjusted differ

Function

Color Mode √ √ √ √ √ User1

Brightness √ √ √ √ - 0 to 100 The screen brightness is adjusted by changing

depending on the color mode.)

√: Adjustable -: Not adjustable

User1 User2

sRGB Paper Movie DICOM

Setting

Range

User2 sRGB

Paper

Movie DICOM

Description Note

Select the desired mode according to the monitor application.

The color setting status can also be adjusted according to personal preference. Select the mode for adjustment and perform adjustment using the relevant functions.

the brightness of the backlight (light source from the LCD back panel).

- 23 -

• For details on the adjustment status of each mode, see “2-

3. Switching Display Modes (Color Modes)” (page 16).

• If the image is too dark even when the brightness is set to 100, adjust the contrast.

Color Mode

(Functions that can be adjusted differ

Function

Contrast √ - - √ - 0 to 100 The brightness of the screen is adjusted by

Temperature √ - √ √ - Off

Gamma √ - - - - 1.8

depending on the color mode.)

√: Adjustable -: Not adjustable

User1 User2

sRGB Paper Movie DICOM

Setting

Range

4000 K to 10000 K (specied in 500 K units, includes 9300 K)

2.0

2.2

2.4

Description Note

varying the video signal level.

Adjust the color temperature. The color temperature is normally used to express the hue of “White” and/or “Black” with a numerical value. The value is expressed in degrees “K” (Kelvin). The screen becomes reddish at low color temperatures and bluish at high color temperatures, similar to the temperatures of a ame. A gain preset value is set for each color temperature setting value.

Adjust the gamma. While the brightness of the monitor varies depending on the input signal, the variation rate is not proportional to the input signal. Maintaining the balance between the input signal and brightness of the monitor is referred to as “Gamma correction”.

Chapter 3 Advanced Adjustment/Setting

• A contrast of 50 displays every color gradation.

• When adjusting the monitor, it is recommended to perform brightness adjustment, which does not lose gradation characteristics, prior to contrast adjustment.

• Perform contrast adjustment in the following cases.

- If the image is too dark even when the brightness is set to 100 (Set the contrast to higher than 50.)

• The value shown in “K” is available only as a reference.

• “Gain” allows you to perform more advanced adjustment.

• If set to “Off”, the image is displayed in the preset color of the monitor (Gain: 100 for each RGB channel).

• When the gain is changed, the color temperature setting changes to “Off”.

• If “Paper” is selected for the color mode, “Paper” is displayed for the gamma value.

• If “DICOM” is selected for the color mode, “DICOM” is displayed for the gamma value.

- 24 -

Color Mode

(Functions that can be adjusted differ

Function

Advanced Settings

Reset √ √ √ √ - - Reset any color adjustments for the currently

Overdrive √ - - - - Enhanced

Hue √ - - √ - -50 to 50 Adjust the hue. • Using this function may

Saturation √ - - √ - -50 to 50 Adjust the color saturation. • Using this function may

Gain √ - - - - 0 to 100 The brightness of each red, green, and blue

depending on the color mode.)

√: Adjustable -: Not adjustable

User1 User2

sRGB Paper Movie DICOM

Setting

Range

Standard

Off

Description Note

This function allows you to set the overdrive intensity based on the use of the monitor. Image lag can be reduced by using the “Enhanced” setting when displaying moving images.

color component is referred to as “Gain”. The hue of “white” can be changed by adjusting the gain.

selected color mode back to the default settings.

Chapter 3 Advanced Adjustment/Setting

make some color gradations unavailable for display.

• The minimum value (-50) changes the screen to monochrome.

• Using this function may make some color gradations unavailable for display.

• The gain value changes according to the color temperature.

• When the gain is changed, the color temperature setting changes to “Off”.

- 25 -

Signal Settings

●

Set the method for outputting the signal input from the PC to the monitor.

Input Signal

(The setting range of each function differs depending on the input signal.)

Function

Picture Expansion √ √ - √ √ Full Screen

√: Settable -: Not settable

HDMI

DisplayPort

- - √ - - Auto

signal

Video signal

DVI

D-Sub

Setting Range Description Note

Aspect Ratio Dot by Dot

Full Screen Aspect Ratio Dot by Dot

The screen size of the monitor display can be changed.

• “Auto” The monitor automatically changes the screen size according to the aspect ratio and resolution information from the PC.

• “Full Screen” Images are stretched to full screen. Since aspect ratios are not maintained, images may be distorted in some cases.

• “Aspect Ratio” Images are enlarged to full screen without changing the aspect ratio. Since aspect ratios are maintained, blank horizontal or vertical borders may appear.

• “Dot by Dot” Displays the image at the set resolution or size specied by the input signal.

Chapter 3 Advanced Adjustment/Setting

• Example settings

- Full Screen

- Aspect Ratio

- Dot by Dot (input signal)

• If the monitor is EV2455 and the

resolution is set to 1920 × 1080, only “Full Screen” is available.

- 26 -

Input Signal

(The setting range of each function differs depending on the input signal.)

Function

Sharpness √ √ √ √ √ 1 to 5 When a low-resolution image is displayed in “Full

Input Color Format √ - - - - Auto

Range Extension √ - √ - - Auto

√: Settable -: Not settable

HDMI

DisplayPort

- √ - - - YUV 4:2:2

- - √ - - Auto

- √ - - - On

signal

Video signal

DVI

D-Sub

Setting Range Description Note

Screen” or “Aspect Ratio” mode, text or lines in the displayed image may be blurred. This function reduces this blurring effect.

The color format of the input signal can be specied. YUV RGB

YUV 4:4:4 RGB

YUV 4:2:2 YUV 4:4:4 RGB

On Off

Off

Try changing this setting if colors are not displayed

correctly.

Depending on the PC, black and white of the video

level of the signal output to the monitor may be limited.

If a limited signal is displayed on the monitor, black

will appear faint and white will appear dull, leading to a

reduction in contrast. The output range of such signals

can be extended to match the actual contrast ratio of

the monitor.

• “Auto” Automatically identies the brightness range of the input signal and displays the image accordingly.

• “On” Extends the signal output range through 0 to 255 and displays the image.

• “Off” Extension of the signal output range is not performed.

Chapter 3 Advanced Adjustment/Setting

• The sharpening setting may not be required depending on the display resolution. (“Sharpness” cannot be selected in such cases.)

• This setting is required when a DVI device is connected to the monitor via the HDMI connector port using a DVIHDMI conversion connector.

• This setting is xed to “RGB” when receiving a DVI signal from the DVI connector.

• Example settings

- Off

- On

• This setting is xed to “Off” for

DVI signal input.

- 27 -

Function

Analog Adjustment

Auto

Screen

Adjust

Auto Range Adjust

Input Signal

(The setting range of each function differs depending on the input signal.)

√: Settable -: Not settable

HDMI

DisplayPort

- - - - √ - Screen ickering, display position, and size can be

- - - - √ - Every color gradation (0 to 255) can be displayed

signal

Video signal

DVI

Setting Range Description Note

D-Sub

adjusted automatically. Selecting “Auto Screen Adjust” displays a message. Select “Yes” to enable this function.

by automatically adjusting the signal output level. Selecting “Auto Range Adjust” displays a message. Select “Yes” to enable this function.

Chapter 3 Advanced Adjustment/Setting

• The automatic screen adjustment function works correctly when an image is fully displayed over the entire displayable area of the screen. It does not work properly in the following cases:

- When an image is only displayed on part of the screen (command prompt window, for example)

- When a black background (wallpaper, etc.) is used

Also, this function may not work properly with some graphic boards.

• When a signal is input into the monitor for the rst time or when a resolution or vertical/ horizontal scan frequency not used before is set, the self adjustment function will activate automatically (only for signals with a resolution of 800×600 (SVGA) or higher).

- 28 -

Input Signal

(The setting range of each function differs depending on the input signal.)

Function

Clock - - - - √ - Flickering of vertical lines on the screen or part of the

√: Settable -: Not settable

HDMI

DisplayPort

signal

Video signal

DVI

Setting Range Description Note

D-Sub

screen can be reduced.

Chapter 3 Advanced Adjustment/Setting

• Use the operation switches ( ) to make ne

adjustments so as not to miss any adjustment points.

Phase - - - - √ - Flickering and blurring over the entire screen can be

Hor.

Position

Ver.

Position

Sound Source √ - - - - Stereo Mini Jack

- - - - √ - The display position (horizontal and vertical) of the

DisplayPort

- - √ - - Stereo Mini Jack HDMI

reduced.

screen can be adjusted.

The audio source can be changed when receiving DisplayPort signal input or HDMI signal input.

• Flickering and blurring may not be completely eliminated depending on your PC or graphics board.

• After setting, adjust the “Clock” again if vertical bars appear.

• Since the number of pixels and pixel positions are xed on the LCD monitor, only one position is provided to display images correctly. Position adjustment is made to shift an image to the correct position.

• This setting is xed to “Stereo Mini Jack” when receiving DVI signal input, HDMI (PC signal) input, or D-Sub signal input.

- 29 -

Preference Settings

●

The monitor’s settings can be congured to suit the usage environment or personal preference.

Function Setting Range Description Note

Menu Rotation 0˚

90˚ 270˚

Menu Position Center

Upper Right Lower Right Lower Left Upper Left

Change the orientation of the Setting menu when using the monitor screen in the portrait display position.

The display position of the Setting menu can be changed. -

Chapter 3 Advanced Adjustment/Setting

• Make sure that the cables are correctly connected.

• Make sure to turn the monitor screen after pulling

the screen up to the uppermost position of the stand and tilting the screen upward.

• When using the monitor screen in a portrait position, a graphics board that supports portrait display is required. When placing the monitor in a portrait position, the settings of your graphics board need to be changed. Refer to the User’s Manual of the graphics board for details.

• The menu cannot be rotated by 180˚. To install the monitor rotated by 180˚, perform monitor adjustment/ settings before rotating the monitor.

- 30 -

Function Setting Range Description Note

Power Save On

Off

Eco Timer Off

0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min, 1, 2, 3, 4, 5 h

Power Indicator On

Off

Border Intensity - When images are displayed at low resolution with “Dot by Dot” or

The monitor can be set to enter power saving mode according to the state of the PC. The monitor changes to power saving mode about 15 seconds after signal input ceases to be detected. When the monitor has shifted to power saving mode, images are not displayed on the screen.

• Exiting power saving mode

- If the monitor receives input, it automatically exits power

saving mode and returns to the normal display mode.

The monitor can be turned off automatically after a specied amount of time has passed in power saving mode. Select the time to wait before turning off power to the monitor.

The power indicator (white) can be turned off during screen display.

“Aspect Ratio” (see “Picture Expansion” (page 26)), a border (black section where the image is not displayed) is displayed around the image. The brightness of this border section can be adjusted.

• At the time of shifting to power saving mode, a message that indicates the transition is displayed 5 seconds in advance.

• When not using the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut completely.

• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore, power consumption of the monitor varies with connected devices even in power saving mode.

• Power consumption varies even when the stereo mini jack cable is connected.

Chapter 3 Advanced Adjustment/Setting

Border

Monitor Reset - Restore all settings to their default values except for the following

settings.

• Settings on the “Administrator Settings” menu

- 31 -

• For details on default settings, see “Main Default

Settings” (page 56).

Language

●

The display language for menus and messages can be selected.

Setting Range

English, Deutsch, Français, Español, Italiano, Svenska, Japanese, Simplied Chinese, Traditional Chinese

Attention

• The display language of the “Administrator Settings” menu cannot be changed.

Information

●

Monitor information (product name, serial number, usage time, resolution, and input signal) can be checked.

Example:

Chapter 3 Advanced Adjustment/Setting

- 32 -

Chapter 4 Administrator Settings

This chapter describes how to congure monitor operation using the “Administrator Settings” menu. This menu is for administrators. Conguration on this menu is not required for normal monitor use.

4-1. Basic Operation of the “Administrator Settings” Menu

Chapter 4 Administrator Settings

Menu display

1. To u c h to turn off the monitor.

2. While touching the leftmost switch, touch to turn on the monitor.

The “Administrator Settings” menu appears.

for more than 2 seconds

Setting

1. Select an item to set with and select .

The Adjustment/Setting menu appears.

2. Set with and select .

The “Administrator Settings” menu appears.

Applying and exiting

1. Select “Apply” and then .

The settings are applied and the “Administrator Settings” menu exits.

Attention

• The language (English) of the “Administrator Settings” menu cannot be changed.

- 33 -

4-2. Functions of the “Administrator Settings” Menu

Function Setting Range Description Note

Auto Input Detection On

Off

DP HPD Control On

Off

HDMI HPD Control On

Off

This monitor recognizes the connector through which PC signals are input and displays images on the screen accordingly. When a PC is turned off or enters power saving mode, any other available signal is displayed automatically.

When this function is set to “Off”, the monitor displays the signal from the selected connector regardless of whether a signal is input or not. In this case, select the input signal to display using

the

When a PC is connected via the DisplayPort connector, window and icon positions may shift when power is turned off/on. If this happens, set this function to “On”.

When a PC is connected via the HDMI connector, the screen may not be displayed depending on the device. If this happens, set this function to “On”.

operation switch on the front of the monitor.

Chapter 4 Administrator Settings

• When this function is set to “On”, the monitor only enters power saving mode after all connected PCs have entered power saving mode or have been switched off.

- 34 -

Function Setting Range Description Note

USB Power Save On

Off

On-Screen Logo On

Off

Key Lock On

Off

Compatibility Mode On

Off

This product can disable USB communication with a PC when the monitor enters power saving mode or when the monitor is turned off. Disabling USB communication can reduce power consumption in power saving mode and when the monitor is turned off.

When this function is set to “Off”, USB connections can be left enabled even when the monitor enters power saving mode or when the monitor is turned off.

When the monitor is turned on, the EIZO logo appears on the screen.

When this function is set to “Off”, the EIZO logo does not appear. In order to prevent changes to settings, the operation switches on

the front of the monitor can be locked.

Depending on the PC and graphics board, the input signal may not be detected and the monitor may not recover from power saving mode. If this happens, set this function to “On”.

Chapter 4 Administrator Settings

• When this function is set to “On”, make sure to complete any communication between connected USB devices and the PC before turning off the monitor. If storage devices, such as a USB ash drive, are connected, turning off the monitor before completing communication may result in data loss or damage to storage devices.

• When this function is set to “On”, the monitor cannot be controlled using software, such as “ScreenManager Pro”, when the monitor is in power saving mode or when the monitor is turned off.

• When this function is set to “Off”, power consumption is higher in power saving mode and when the monitor is turned off.

• The following operation is available even if the switches are locked:

- Turning the monitor on or off with the Power switch

- 35 -

Chapter 5 Troubleshooting

If a problem still remains after applying the suggested remedies, contact your local EIZO representative.

5-1. No picture

Problem Possible cause and remedy

1. No picture

• Power indicator does not light up.

• Power indicator is lighting white. • Increase “Brightness”, “Contrast”, or “Gain” in the Setting menu (see “Color Adjustment” (page 23)).

• Power indicator is lighting orange. • Switch the input signal.

• Power indicator is ashing orange. • This symptom may occur when the PC is connected to the DisplayPort connector. Use a signal cable recommended by

• Check whether the power cord is connected properly.

• Turn the main power switch on.

• To uch

• Turn off the main power, and then turn it on again a few minutes later.

• Move the mouse or press any key on the keyboard.

• Check whether the PC is turned on.

• Depending on the PC and graphics board, the input signal may not be detected and the monitor may not recover from

power saving mode. If the screen is not displayed by moving the mouse or pressing keys on the keyboard, perform the following procedure. This may resolve the problem.

1. Touch

2. While touching the leftmost switch, touch

3. Select “Compatibility Mode”.

4. Select “On”.

5. Select “Apply” and then

6. Reboot the PC.

• When the PC is connected via HDMI, try changing the “HDMI HPD Control” setting on the “Administrator Settings” menu to “On” (see “HDMI HPD Control” (page 34)).

• When the EcoView Sense function is “On”, the monitor may have shifted to power saving mode. Come near to the monitor. If the screen is not displayed, move the mouse or press any key on the keyboard.

us for the connection. Turn the monitor off and on.

to turn off the monitor.

for more than 2 seconds.

The “Administrator Settings” menu appears.

- 36 -

Chapter 5 Troubleshooting

Problem Possible cause and remedy

2. The message below appears. This message appears when the signal is not input correctly even though the monitor is functioning properly.

• The message shows that the input signal is out of the specied frequency range.

Example:

• Check whether the PC is congured to meet the resolution and vertical scan frequency requirements of the monitor (see

“1-3. Supported Resolutions” (page 11)).

• Reboot the PC.

• Select an appropriate setting using the graphics board’s utility. Refer to the User’s Manual of the graphics board for

details.

- 37 -

Chapter 5 Troubleshooting

5-2. Imaging problems (for both digital and analog)

Problem Possible cause and remedy

1. The screen is too bright or too dark. • Use “Brightness” or “Contrast” in the Setting menu to adjust it (see “Color Adjustment” (page 23)). (The LCD

monitor backlight has a limited life span. When the screen becomes dark or begins to icker, contact your local EIZO representative.)

• If the screen is too bright, try changing the Auto EcoView setting to “On”. The monitor detects the ambient brightness to adjust the screen brightness automatically (see “Auto EcoView” (page 18)).

2. “Brightness” cannot be adjusted When Auto EcoView is set to “On”, “Brightness” may not be adjustable due to the advanced settings of Auto EcoView.

• Cannot increase/decrease setting value (“

or “

” is displayed in gray)

- “Brightness” adjustment menu via operation switch

- “Brightness” adjustment menu in color adjustment

• Cannot increase/decrease setting value (“

and “

3. Text is blurred • Check whether the PC is congured to meet the resolution and vertical scan frequency requirements of the monitor (see

4. Afterimages appear • Afterimages are particular to LCD monitors. Avoid displaying the same image for a long time.

” are displayed in gray)

- “Brightness” adjustment menu via operation switch

- “Brightness” adjustment menu in color adjustment

”

• The bright adjustment range of the Auto EcoView function can be limited to ensure that the screen is neither too bright nor too dark. When the adjustment range is limited, values outside the range cannot be set. If you want to set a value outside the range, try changing the following settings.

- Change the maximum and minimum values for “Brightness” in the Auto EcoView advanced settings.

- Set Auto EcoView to “Off”.

For details on Auto EcoView settings, see “Auto EcoView” (page 18).

”

• Brightness adjustment may not be possible when the installation environment of the monitor is excessively bright or dark. In this case, try changing the following settings.

- Change the maximum and minimum values for “Ambient Light” in the Auto EcoView advanced settings.

- Set Auto EcoView to “Off”.

For details on Auto EcoView settings, see “Auto EcoView” (page 18).

“1-3. Supported Resolutions” (page 11)).

• When an image is displayed with a resolution other than recommended, text or lines in the displayed image may blur. In this case, try adjusting “Sharpness” in the Setting menu (see “Sharpness” (page 27)).

• Use the screen saver or power saving function to avoid displaying the same image for extended periods of time.

- 38 -

Problem Possible cause and remedy

5. Green / red / blue / white dots or dark dots remain on the screen.

6. Interference patterns or pressure marks remain on the screen.

7. Noise appears on the screen. • In the Setting menu, set “Overdrive” to “Off” (see “Overdrive” (page 25)).

• This is due to LCD panel characteristics and not a malfunction.

• Leave the monitor with a white or black screen. The symptom may disappear.

• When inputting HDCP system signals, normal images may not be displayed immediately.

Chapter 5 Troubleshooting

8. (When using DisplayPort signal input) Position of windows and icons is shifted when turning power off/on.

• Turn the setting “On” for “DP HPD Control” on the “Administrator Settings” menu (see “DP HPD Control” (page 34)).

5-3. Imaging problems (for analog only)

Problem Possible cause and remedy

1. Display position is incorrect.

2. Vertical bars appear on the screen or a part

oftheimageisickering.

3. Wholescreenisickeringorblurring.

• Use “Position” in the Setting menu to correct the image position (see “Hor. Position” (page 29), “Ver. Position” (page

29)).

• If the problem persists, use the graphics board’s utility if available to change the display position.

• Use “Clock” in the Setting menu to adjust it (see “Clock” (page 29)).

• Use “Phase” in the Setting menu to adjust it (see “Phase” (page 29)).

- 39 -

5-4. Other problems

Problem Possible cause and remedy

1. The Setting menu does not appear. • Check whether the switch operation lock function is active (see “Key Lock” (page 35)).

2. No audio output. • Check whether the stereo mini jack cable is connected properly.

• Check whether volume is set to 0.

• Check the PC and audio playback software to see whether they are congured correctly.

• Check the “Source” setting when using DisplayPort input or HDMI input (see “Sound Source” (page 29)).

3. (When using EcoView Sense) The screen does not turn off after moving away from the monitor or the screen does not turn on when approaching the monitor.

4. USB devices connected to the monitor do not work.

• Check the installation environment of the monitor. The presence sensor may not work correctly in the following environments.

- The monitor is located in a place affected by wind.

- There is a heat emitting device near the monitor.

- There is an obstacle in front of the sensor.

• Check whether there sensor is dirty. Clean the sensor with a soft cloth.

• Check whether you are straight in front of the monitor. The EcoView Sense function is activated when the sensor on

the front of the monitor detects the movement of heat.

• In high temperature conditions, the monitor may not recover from power saving mode. If the screen is not displayed even after moving the mouse or pressing any key on the keyboard, turn the monitor off and on using its power switch. When the screen is displayed, increase the detection sensitivity value (see “EcoView Sense” (page 19)).

• Check whether the USB cable is connected correctly (see “6-5. Making Use of USB (Universal Serial Bus)” (page 49)).

• Try changing to a different USB port. If the PC or peripheral devices work correctly by changing the USB port, contact

your local EIZO representative. (Refer to the manual of the PC for details.)

• Reboot the PC.

• If the peripheral devices work correctly when the PC and peripheral devices are connected directly, contact your local

EIZO representative.

• Check whether the PC and OS are USB compliant. (For USB compliance of the respective devices, consult their manufacturers.)

• Check the PC’s BIOS setting for USB when using Windows. (Refer to the manual of the PC for details.)

Chapter 5 Troubleshooting

- 40 -

Chapter 6 Reference

6-1. Attaching the Optional Arm

An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our web site for the corresponding optional arm (or optional stand). www.eizoglobal.com

Attention

• When attaching an arm or stand, follow the instructions of the respective User’s Manual.

• When using another manufacturer’s arm or stand, conrm the following in advance and select one conforming to the VESA standard. Use the screws securing the unit and the

stand.

- Clearance between screw holes: 100 mm × 100 mm

- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less

- Plate thickness: 2.6 mm

- Strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.

• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:

Orientation

Movement range (tilt angle)

Up: 45˚ Down: 45˚

*1 When installed in this orientation, periodically clean the area around the power connector. Dust, water, or oil adhered to this area may result in re.

• Connect the cables after attaching an arm or stand.

• Do not move the removed stand up and down. Doing so may result in injury or device damage.

• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.

- 41 -

Attachment procedure

LaytheLCDmonitoronasoftclothspreadoverastableandatsurface

with the panel surface facing down.

Remove the stand.

Prepare a screwdriver. Use the screwdriver to loosen the screws (four) that secure the unit to the stand.

Attach the arm or stand to the monitor.

Secure the monitor to the arm or stand using the screws specied in the User’s Manual of the arm or stand.

6-2. Detaching/Attaching Stand Base

Detachment procedure

The stand base that was attached during setup can be detached using the following procedures.

Chapter 6 Reference

Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing down.

Turnthexingscrewonthestandbasetodetachit.

Note

• The xing screw can be removed by hand. If the xing screw is too tight, use a coin or athead screwdriver.

- 42 -

Turn the stand base in the counterclockwise direction to detach it.

Note

• Reattach the xing screw onto the stand base for when the stand base is used again.

Attachment procedure

The once removed the stand base can be attached to the monitor again with the following procedures.

Chapter 6 Reference

Checkthatthexingscrewisrmlyattachedtothebottomofthestandbase.

Place the stand base on a stable surface.

- 43 -

Insert the stand brace into the stand base.

Chapter 6 Reference

Stand brace

Stand base

- 44 -

Turn the stand brace in the clockwise direction until it clicks.

Chapter 6 Reference

Click!

- 45 -

6-3. Attaching/Detaching the Cable Holder

A cable holder is supplied with this product. Use the cable holder to organize the cables connected to the monitor.

Attachment procedure

Pass the cables through the cable holder.

Close the opening in the cable holder.

Chapter 6 Reference

While holding the cable holder closed, attach it onto the stand.

- 46 -

Chapter 6 Reference

Note

• The cable holder can be inserted either perpendicular or parallel to the stand. Change the direction of the cable holder according to the condition of the cables.

Detachment procedure

Close the opening in the cable holder.

While holding the cable holder closed, remove it from the stand.

- 47 -

6-4. Connecting Multiple PCs

This product can be connected to multiple PCs and allows you to switch between the connections for display.

Chapter 6 Reference

Connection

examples

connector

Analog Input (D -Sub)

Signal cable MD-C87 (option)

D-Sub

DisplayPort

connector

Digital (DisplayPort)

Signal cable PP200 (supplied)

Digital (HDMI)

HDMI cable (commercially available product)

HDMI

connector

Digital (DVI)

Signal cable FD-C39 (option)

DVI-D

Note

• The input signal changes each time the operation switch on the front

of the monitor is touched. When the signal is switched, the active input port name appears at the top right corner of the screen.

• This product automatically recognizes

the connector through which PC signals are input and displays images on the screen accordingly. For details, see

“Auto Input Detection” (page 34).

D-Sub mini

15-pin connector

To PC 1 To PC 2 To PC 3 To PC 4

DisplayPort

connector

- 48 -

DVI connectorHDMI connector

Chapter 6 Reference

6-5. Making Use of USB (Universal Serial Bus)

This monitor is equipped with a USB hub. It functions as a USB hub when connected to a USB-compatible PC, allowing the connection of peripheral USB devices.

Note

• This product supports USB 3.0. When connecting to peripheral devices that support USB 3.0, high-speed data communication is possible (however, only when the USB cable used to connect the PC and peripheral device is USB 3.0 compliant).

Required System Environment

●

• A PC equipped with a USB port

• Windows 8.1 / Windows 8 / Windows 7 / Windows Vista, Mac OS X 10.2 or later, Mac OS 9.2.2

• EIZO USB cable (UU200SS (USB 3.0))

Attention

• This monitor may not work depending on the PC, OS, or peripheral devices to be used. For USB compatibility of peripheral devices, contact their manufacturers.

• When the monitor is in power saving mode, devices connected to the USB downstream port will still work. Therefore, power consumption of the monitor varies with

connected devices even in power saving mode.

• When the main power of the monitor is off, a device connected to the USB downstream port will not operate.

Connection Procedure (Setup of USB Function)

●

1. Connect the monitor rst to a PC using the signal cable, and start the PC.

2. Connect the USB cable between the USB downstream port of the PC and the USB upstream port of the monitor.

The USB hub function is set up automatically upon connection of the USB cable.

3. Connect a peripheral USB device to the USB downstream port of the monitor.

- 49 -

USB

downstream

port

USB

upstream port

6-6. Specications

EV2450

LCD Panel Typ e IPS (Anti-Glare)

Backlight LED Size 60 cm (23.8 inch) (60.4 cm diagonal) Native Resolution 1920 dots × 1080 lines Display Size (H × V) 527.04 mm × 296.46 mm Pixel Pitch 0.2745 mm Display Colors 8-bit colors: 16.77 million colors Viewing Angle (H / V, typical) 178˚ / 178˚ Response Time (typical) Gray-to-gray: 14 ms (overdrive setting: Off)

5 ms (overdrive setting: Enhanced)

Video Signals Input Terminals DisplayPort (HDCP) × 1, HDMI TypeA (HDCP)

Digital Scanning Frequency (H / V) 31 kHz to 68 kHz (DisplayPort, DVI), 15 kHz to 68 kHz (HDMI) / 59 Hz to 61 Hz (DisplayPort, DVI), 49 Hz to 61 Hz (HDMI)

(VGA TEXT: 69 Hz to 71 Hz) Analog Scanning Frequency (H / V) 31 kHz to 81 kHz / 55 Hz to 76 Hz Synchronization Signal Separate Max. Dot Clock 148.5 MHz

USB Port Upstream port × 1, downstream port × 2

Standard USB Specication Revision 3.0 Communication Speed 5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low) Supply Current Downstream: Max. 900 mA per port

Audio Audio Input Format DisplayPort: 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)

HDMI: 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz) Speakers 1 W + 1 W Headphones 2 mW + 2 mW (32 Ω) Input Terminals Line: Stereo mini jack × 1

DisplayPort × 1, HDMI TypeA × 1 (shared with video signal) Output Terminals Headphones: Stereo mini jack × 1

*1 HDMI CEC (or mutual control) is not supported.

× 1, DVI-D (HDCP) × 1, and D-Sub mini 15-pin × 1

Chapter 6 Reference

- 50 -

Power Input 100 - 120 VAC ±10 %, 50 / 60 Hz 0.80 A

200 - 240 VAC ±10 %, 50 / 60 Hz 0.50 A Maximum Power Consumption 44 W or less Power Save Mode 0.3 W or less (no USB device connected, default settings) Standby Mode 0.3 W or less (no USB device connected, default settings)

Physical Specications

Operating Environmental Requirements

Transportation/ Storage Environmental Requirements

Dimensions Min. height:

Max. height: Dimensions (Without Stand) 537.6 mm × 317.6 mm × 47.9 mm (W × H × D) Net Weight Approx. 5.8 kg Net Weight (Without Stand) Approx. 3.4 kg Height Adjustment Range 114.7 mm (Tilt: 35˚) / 140 mm (Tilt: 0˚) Tilt Up 35˚, down 5˚ Swivel 344˚ Vertical Rotation Left 90˚, right 90˚ Temperature 5˚C to 35˚C (41˚F to 95˚F) Humidity 20% to 80% R.H. (no condensation) Air Pressure 540 hPa to 1060 hPa Temperature -20˚C to 60˚C (-4˚F to 140˚F) Humidity 10% to 90% R.H. (no condensation) Air Pressure 200 hPa to 1060 hPa

537.6 mm × 335.1 mm × 278.3 mm (W × H × D) (Tilt: 35˚)

537.6 mm × 473.5 mm × 233 mm (W × H × D) (Tilt: 0˚)

Chapter 6 Reference

- 51 -

EV2455

LCD Panel Ty p e IPS (Anti-Glare)

Backlight LED Size 61 cm (24.1 inch) (61.1 cm diagonal) Native Resolution 1920 dots × 1200 lines Display Size (H × V) 518.4 mm × 324.0 mm Pixel Pitch 0.27 mm Display Colors 8-bit colors: 16.77 million colors Viewing Angle (H / V, typical) 178˚ / 178˚ Response Time (typical) Gray-to-gray: 14 ms (overdrive setting: Off)

5 ms (overdrive setting: Enhanced)

Video Signals Input Terminals DisplayPort (HDCP) × 1, HDMI TypeA (HDCP)

Digital Scanning Frequency (H / V) 31 kHz to 76kHz (DisplayPort, DVI), 15 kHz to 76kHz (HDMI) / 59 Hz to 61 Hz (DisplayPort, DVI), 49 Hz to 61 Hz

(HDMI) (VGA TEXT: 69 Hz to 71 Hz) Analog Scanning Frequency (H / V) 31 kHz to 81 kHz / 55 Hz to 76 Hz Synchronization Signal Separate Max. Dot Clock 162 MHz

USB Port Upstream port × 1, downstream port × 2

Standard USB Specication Revision 3.0 Communication Speed 5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low) Supply Current Downstream: Max. 900 mA per port

Audio Audio Input Format DisplayPort: 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)

HDMI: 2ch linear PCM (32 kHz / 44.1 kHz / 48 kHz) Speakers 1 W + 1 W Headphones 2 mW + 2 mW (32 Ω) Input Terminals Line: Stereo mini jack × 1

DisplayPort × 1, HDMI TypeA × 1 (shared with video signal) Output Terminals Headphones: Stereo mini jack × 1

*1 HDMI CEC (or mutual control) is not supported.

× 1, DVI-D (HDCP) × 1, and D-Sub mini 15-pin × 1

Chapter 6 Reference

- 52 -

Power Input 100 - 120 VAC ±10 %, 50 / 60 Hz 0.85 A

200 - 240 VAC ±10 %, 50 / 60 Hz 0.55 A Maximum Power Consumption 49 W or less Power Save Mode 0.3 W or less (no USB device connected, default settings) Standby Mode 0.3 W or less (no USB device connected, default settings)

Physical Specications

Operating Environmental Requirements

Transportation/ Storage Environmental Requirements

Dimensions Min. height:

Max. height: Dimensions (Without Stand) 530.8 mm × 347.2 mm × 47.9 mm (W × H × D) Net Weight Approx. 6.5 kg Net Weight (Without Stand) Approx. 4.1 kg Height Adjustment Range 114.7 mm (Tilt: 35˚) / 131 mm (Tilt: 0˚) Tilt Up 35˚, down 5˚ Swivel 344˚ Vertical Rotation Left 90˚, right 90˚ Temperature 5˚C to 35˚C (41˚F to 95˚F) Humidity 20% to 80% R.H. (no condensation) Air Pressure 540 hPa to 1060 hPa Temperature -20˚C to 60˚C (-4˚F to 140˚F) Humidity 10% to 90% R.H. (no condensation) Air Pressure 200 hPa to 1060 hPa

530.8 mm × 347.0 mm × 286.4 mm (W × H × D) (Tilt: 35˚)

530.8 mm × 488.2 mm × 233.0 mm (W × H × D) (Tilt: 0˚)

Chapter 6 Reference

- 53 -

Outside Dimensions

●

EV2450

Chapter 6 Reference

Unit: mm

35°

TILT

5°

5.3

SWIVEL 344°

537.6

527(ACTIVE AREA)

90°

PIVOT

5.3

15.9

47.9

317.6

588.8

473.5

179.4

155.9

64.7

140

45.3

278.3

233

335.1

17.2

368

100

(VESA)

114.1 103.5

218.8 218.8

100

(VESA)

- 54 -

EV2455

Chapter 6 Reference

35°

TILT

SWIVEL 344°

530.8

518.4(ACTIVE AREA)

90°

PIVOT

47.9

1.31.3

1.3

332.4

573.4

488.2

2.2

14.8

5°

169.1

54.4

131

141

45.3

286.4

17.2

368

347

100 118.2129

(VESA)

215.4 215.4

100

(VESA)

- 55 -

233

Main Default Settings

●

Auto EcoView On EcoView Optimizer 2 On EcoView Sense Off Color Mode User1 Picture Expansion DisplayPort input Aspect Ratio

HDMI (PC signal) input Aspect Ratio HDMI (video signal) input Auto DVI-D input Aspect Ratio D-Sub input Aspect Ratio

Input Color Format DisplayPort input Auto

HDMI (PC signal) input RGB

HDMI (video signal) input Auto Menu Position Center Power Save On Eco Timer Off Language English Power Indicator On Auto Input Detection On DP HPD Control Off HDMI HPD Control Off USB Power Save On On-Screen Logo On Key Lock Off Compatibility Mode Off

Chapter 6 Reference

Accessories

●

Signal cable • MD-C87 (D-Sub-D-Sub)

• FD-C39 (DVI-DVI)

Cleaning Kit EIZO “ScreenCleaner” For the latest information about accessories, refer to our web site. www.eizoglobal.com

- 56 -

6-7. Preset Timings

The following table lists the factory preset analog signal timings:

Attention

• The display position may deviate depending on the connected PC, and may require screen adjustment using the Setting menu.

• If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen display may still be incorrect even after adjustment.

• When interlaced signals are used, the screen cannot be displayed correctly even after screen adjustment using the Setting menu.

EV2450

Chapter 6 Reference

Resolution Applicable Signals

640 × 480 VGA /CEA-861 25.18 31.47 59.94 640 × 480 CEA-861 25.20 31.50 60.00 640 × 480 VESA 31.50 37. 8 6 72.81 640 × 480 VESA 31.50 37. 5 0 75.00 720 × 400 VGA TEXT 28.32 31.47 70.09 800 × 600 VESA 36.00 35 .16 56.25 800 × 600 VESA 40.00 37.88 60.32 800 × 600 VESA 50.00 48.08 72.19

800 × 600 VESA 49.50 46.88 75.00 1024 × 768 VESA 65.00 48.36 60.00 1024 × 768 VESA 75.00 56.48 70.07 1024 × 768 VESA 78.75 60.02 75.03 1280 × 720 CEA-861 74.25 45.00 60.00 1280 × 800 VESA CVT 83.50 49.70 59.81

1280 × 1024 VESA 108.00 63.98 60.02 1280 × 1024 VESA 135.00 79.98 75.03

1600 × 900 VESA RB 108.00 60.00 60.00

1680 × 1050 VESA CVT 146.25 65.29 59.95 1680 × 1050 VESA CVT RB 119.0 0 64.67 59.88 1920 × 1080 CEA-861 148.50 6 7. 50 60.00

Dot Clock: MHz Horizontal: kHz Vertical: Hz

Frequency

- 57 -

EV2455

Chapter 6 Reference

Resolution Applicable Signals

640 × 480 VGA /CEA-861 25.18 31.47 59.94

640 × 480 CEA-861 25.20 31.50 60.00

640 × 480 VESA 31.50 37. 8 6 72.81

640 × 480 VESA 31.50 37. 5 0 75.00

720 × 400 VGA TEXT 28.32 31.47 70.09

800 × 600 VESA 36.00 35 .16 56.25

800 × 600 VESA 40.00 37.88 60.32

800 × 600 VESA 50.00 48.08 72 .19

1280 × 1024 VESA 108.00 63.98 60.02 1280 × 1024 VESA 135.00 79.98 75.03

1600 × 900 VESA RB 108.00 60.00 60.00

1600 × 1200 VESA 162.00 75.00 60.00 1680 × 1050 VESA CVT 146.25 65.29 59.95 1680 × 1050 VESA CVT RB 119.0 0 64.67 59.88 1920 × 1080 CEA-861 148.50 6 7. 50 60.00 1920 × 1200 VESA CVT 193.25 74.56 59.89 1920 × 1200 VESA CVT RB 154.00 74.04 59.95

Dot Clock: MHz Horizontal: kHz Vertical: Hz

Frequency

- 58 -

Chapter 7 Glossary

Clock

The analog signal input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in use, when the analog signal is converted to a digital signal for image display. This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.

DICOM (Digital Imaging and Communication in Medicine)

The DICOM standard was developed by the American College of Radiology and the National Electrical Manufacturer’s Association of the USA. The DICOM compatible device connection enables to transfer the medical image and information. The DICOM, Part 14 document denes the digital, grayscale medical image display.

DisplayPort

This is the interface standard for image signals standardized in accordance with VESA. It was developed with the aim of replacing the conventional DVI and analog interfaces, and it can transmit high resolution signals and sound signals, which DVI does not support. The standard size and mini size connectors have been standardized.

Chapter 7 Glossary

DVI (Digital Visual Interface)

DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss. This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal inputs.

Gain

This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light passing through the panel color lter. Red, green and blue are the three primary colors. All the colors on the screen are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume) passing through each color’s lter.

- 59 -

Chapter 7 Glossary

Gamma

Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a highcontrast image.

HDCP (High-bandwidth Digital Content Protection)

Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or HDMI connector on the output side and decoding them on the input side. Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable to HDCP system.

HDMI(High-DenitionMultimediaInterface)

HDMI is a digital interface standard, developed for consumer electrical appliance or AV device. This standard is issued on the basis of the DVI standard which is one of an interface specication for the connection between a PC and a monitor. The projected image, sound and control signal without compressed enable to be transmitted with one cable.

Overdrive

This technology enhances response speed by increasing the potential difference at the time of motion of liquid-crystal pixels, and it is used for liquidcrystal TV sets and others in general. It provides clear-cut three-dimensional display with little afterimage, by improving response speed of the intermediate graduation range that frequently appears in moving images.

Phase

Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly.

Range Adjustment

Range adjustment controls the signal output levels to display every color gradation. It is recommended that range adjustment be made before color adjustment.

- 60 -

Chapter 7 Glossary

Resolution

The LCD panel consists of numerous pixels of specied size, which are illuminated to form images. This monitor consists of horizontal 1920 pixels and 1080 vertical pixels (EV2450), or horizontal 1920 pixels and 1200 vertical pixels (EV2455). At a resolution of 1920 × 1080 (EV2450) or 1920 × 1200 (EV2455), all pixels are illuminated as a full screen (1:1).

sRGB (Standard RGB)

International standard for color reproduction and color space among peripheral devices (such as monitors, printers, digital cameras, scanners). As a form of simple color matching for the Internet, colors can be displayed using tones close to those of the transmission and reception devices.

Temperature

Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen becomes reddish at a low temperature, and bluish at a high temperature, like the ame temperature. 5000 K: Slightly reddish white 6500 K: White referred to as daylight-balanced color 9300 K: Slightly bluish white

TMDS (Transition Minimized Differential Signaling)

A signal transmission system for digital interface.

- 61 -

Appendix

Trademark

The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.

The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics Standards Association. The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers

Forum, Inc. The USB Power Delivery Trident Logos are trademarks of USB Implementers Forum,

Inc. DICOM is the registered trademark of the National Electrical Manufacturers Association for its standards publications relating to digital communications of

medical information. Kensington and Microsaver are registered trademarks of ACCO Brands Corporation. Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other countries. Apple, macOS, Mac OS, OS X, Macintosh and ColorSync are registered trademarks of Apple Inc. EIZO, the EIZO Logo, ColorEdge, CuratOR, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor and ScreenManager are registered

trademarks of EIZO Corporation in Japan and other countries. ColorEdge Tablet Controller, ColorNavigator, EcoView NET, EIZO EasyPIX, EIZO Monitor Congurator, EIZO ScreenSlicer, G-Ignition, i•Sound, Quick Color

Match, RadiLight, Re/Vue, SafeGuard, Screen Administrator, Screen InStyle, ScreenCleaner and UniColor Pro are trademarks of EIZO Corporation. All other company names, product names, and logos are trademarks or registered trademarks of their respective companies.

Appendix

License / Copyright

A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.

- 62 -

ENERGY STAR

As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets the ENERGY STAR guidelines for energy efciency.

TCOCertied

This product carries the TCO Certied designation (EcoView Optimizer 2: Off, Temperature: Off). TCO Certied is the leading independent sustainability certication for IT products. For details, see the following pages.

Appendix

- 63 -

Appendix

A third-party cercaon according to ISO 14024

Toward sust ainable IT pro ducts

Say hello to a more sustainable product

IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violaons are common in the factories. Harmful substances are used both in products and their manufacture. Products can oen have a short lifespan because of poor ergonomics, low quality and when they are not able to be repaired or upgraded.

This product is a beer choice.

Thank you for making a responsible product choice, that help drive progress towards a more sustainable future!

Criteria in TCO Certified have a life-cycle perspective and balance environmental and social responsibility. Conformity is verified by independent and approved veriers that specialize in IT products, social responsibility or other sustainability issues. Vericaon is done both before and aer the cercate is issued, covering the entire validity period. The process also includes ensuring that corrective actions are implemented in all cases of factory nonconformies. And last but not least, to make sure that the cercaon and independent vericaon is accurate, both TCO Cered and the veriers are reviewed regularly.

It meets all the criteria in TCO Cered, the world’s most comprehensive sustainability cercaon for IT products.

Want to know more?

Read informaon about TCO Cered, full criteria documents, news and updates at tcocered.com. On the website you’ll also nd our Product Finder, which presents a complete, searchable lisng of cered products.

- 64 -

Appendix

FCC Declaration of Conformity

For U.S.A. , Canada, etc. (rated 100-120 Vac) Only

FCC Declaration of Conformity

We, the Responsible Party EIZO Inc.

5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011

declare that the product Trade name: EIZO

Model: FlexScan EV2450 / EV2455

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

* Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help.

Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser’sauthoritytooperatethe

equipment.

- 65 -

Appendix

Note

UsetheattachedspeciedcablebeloworEIZOsignalcablewiththismonitorsoastokeepinterferencewithinthelimitsofaClassBdigitaldevice.

- AC Cord

- Shielded Signal Cable (enclosed)

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

- 66 -

LIMITED WARRANTY

EIZO Corporation (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the “Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the “ speci ed in this document (hereinafter referred to as the “

”) from EIZO or Distributors, that EIZO and Distributors shall, at their sole discretion, either repair or replace the Product at no charge if the Original Purchaser becomes aware within the Warranty Period (de ned below) that the Product malfunctions or is damaged in the course of normal use of the Product in accordance with the description in the instruction manual attached to the Product (hereinafter referred to as the “

The period of this Warranty is limited to (i)  ve (5) years from the date of purchase of the Product; or, limited to the expiration of (ii) 30,000 hours of its use of the Product (hereinafter referred to as the “ than as provided under this Warranty.

EIZO and Distributors will cease to hold or store any parts of the Product upon expiration of seven (7) years after the production of such parts is discontinued. In repairing the monitor, EIZO and Distributors will use renewal parts which comply with our QC standards.

The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict any legal rights of the Original Purchaser. Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty whatsoever in any of the cases as set forth below:

To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of such purchase when requesting services under the Warranty.

The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original Warranty Period. EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER INFORMATION STORED IN ANY MEDIA OR ANY PART OF ANY

PRODUCT RETURNED TO EIZO OR DISTRIBUTORS FOR REPAIR. EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCT AND ITS QUALITY, PERFORMANCE,

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/ OR SALES.

Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who purchased the product

Product

User’s Manual”).

(a) Any defect of the Product caused by freight damage, modi cation, alteration, abuse, misuse, accident, incorrect installation, disaster, faulty maintenance and/or improper repair

by third party other than EIZO and Distributors; (b) Any incompatibility of the Product due to possible technical innovations and/or regulations; (c) Any deterioration of the sensor; (d) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel and/or backlight, etc. (e.g. changes in brightness, changes in

brightness uniformity, changes in color, changes in color uniformity, defects in pixels including burnt pixels, etc.); (e) Any defect of the Product caused by external equipment; (f) Any defect of the Product on which the original serial number has been altered or removed; (g) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g. buttons, rotating parts, cables, User’s Manual, etc.); and (h) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD panel.

Warranty Period”). EIZO and Distributors shall bear no liability or obligation with regard to the Product in relation to the Original Purchaser or any third parties other

Appendix

- 67 -

Appendix

Recycling Information

This product, when disposed of, is supposed to be collected and recycled according to your country’s legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or an afliate in your country. The contact addressees are listed on the EIZO website below.

www.eizoglobal.com

For recycling information for customers in Switzerland, please refer to the following website.

www.swico.ch

Informationen zum Thema Recycling

Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden. Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in Ihrem Land. Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.

www.eizoglobal.com

Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:

www.swico.ch

Informations sur le recyclage

Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de votre pays, an de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un distributeur ou une société afliée de votre pays. Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.

www.eizoglobal.com

Pour les clients en Suisse, veuillez consulter le site Web suivant an d’obtenir des informations sur le recyclage.

www.swico.ch

Información sobre reciclaje

Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o una lial de su país. Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.

www.eizoglobal.com

- 68 -

Appendix

Informazioni sul riciclaggio

Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un afliato presenti nel proprio paese. Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.

www.eizoglobal.com

Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.

www.swico.ch

Återvinningsinformation

När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land. Kontaktadresserna listas på EIZO-webbplatsen nedan.

www.eizoglobal.com

Πληροφορίεςανακύκλωσης

Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας. Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.

www.eizoglobal.com

Сведенияпоутилизации

По истечении срока службы данного продукта его следует принести на сборный пункт и утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к дистрибьютору или в местное представительство компании в вашей стране. Контактные адреса можно найти на веб-узле EIZO.

www.eizoglobal.com

Informatie over recycling

Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact opnemen met een distributeur of een partner in uw land. De contactadressen worden vermeld op de volgende EIZO-website.

www.eizoglobal.com

- 69 -

Appendix

Informação sobre reciclagem

Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma lial no seu país. Os endereços de contacto estão listados no website do EIZO, abaixo.

www.eizoglobal.com

Oplysninger om genbrug

Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du kontakte en distributør eller et tilknyttet selskab i dit land. Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.

www.eizoglobal.com

Kierrätystä koskevia tietoja

Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi. Yhteystiedot löytyvät EIZOn Internet-sivustolta.

www.eizoglobal.com

Wykorzystanie surowców wtórnych

Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej rmy EIZO.

www.eizoglobal.com

Informace o recyklaci

Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo pobočku ve své zemi. Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.

www.eizoglobal.com

Ringlussevõtu alane teave

Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või liaaliga oma riigis. Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:

www.eizoglobal.com

- 70 -

Appendix

Újrahasznosítási információ

Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani, hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy országon belüli forgalmazóval vagy társvállalkozással. A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:

www.eizoglobal.com

Podatki o recikliranju

Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali podružnico. Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:

www.eizoglobal.com

Informácie o recyklácii

Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo vašej krajine. Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke rmy EIZO:

www.eizoglobal.com

Pārstrādesinformācija

Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai pārstāvniecību jūsu valstī. Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.

www.eizoglobal.com

Informacijaapiegrąžinamąjįperdirbimą

Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią gaminių pardavimo atstovybę arba jos lialą. Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.

www.eizoglobal.com

Информацияотноснорециклиране

При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи за това във вашата страна. Данните за връзка с нас са описани на следния Интернет сайт на EIZO:

www.eizoglobal.com

- 71 -

Appendix

Informaţiereferitoarelareciclare

Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un aliat al ţării respective. Adresele de contact le găsiţi pe pagina de web al EIZO:

www.eizoglobal.com

GeriDönüşümBilgisi

Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya ilgili kuruluşla temasa geçiniz. İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.

www.eizoglobal.com

- 72 -

03V2512 9 H1

UM-EV2450

8th Edition-September, 2019

Eizo EV2450, EV2455 User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

User’s Manual

Notice for this monitor

Cleaning

To use the monitor comfortably

CONTENTS

1-1. Features

Chapter 1 Introduction

1-2. Controls and Functions

Front

Rear

1-3. Supported Resolutions

EV2450

EV2455

1-4. Setting the Resolution

Windows 8.1 / Windows 8 / Windows 7

Windows Vista

Mac OS X

Chapter 2 Basic Adjustment/Setting

2-1. Switch Operation Method

2-2. Switching Input Signals

2-3. Switching Display Modes (Color Modes)

Display Modes

2-4. Conserving Energy

2-5. Adjusting Brightness

2-6. Adjusting Volume

3-1. Basic Operation of the Setting menu

Chapter 3 Advanced Adjustment/Setting

3-2. Setting Menu Functions

Color Adjustment

Signal Settings

Preference Settings

Language

Information

4-1. Basic Operation of the “Administrator Settings” Menu

Chapter 4 Administrator Settings

4-2. Functions of the “Administrator Settings” Menu

Chapter 5 Troubleshooting

5-1. No picture

5-2. Imaging problems (for both digital and analog)

5-3. Imaging problems (for analog only)

5-4. Other problems

Chapter 6 Reference

6-1. Attaching the Optional Arm

6-2. Detaching/Attaching Stand Base

6-3. Attaching/Detaching the Cable Holder

6-4. Connecting Multiple PCs

6-5. Making Use of USB (Universal Serial Bus)

Required System Environment

Connection Procedure (Setup of USB Function)

Outside Dimensions

Main Default Settings

Accessories

6-7. Preset Timings

Chapter 7 Glossary

Appendix

Trademark

License / Copyright

ENERGY STAR

FCC Declaration of Conformity

LIMITED WARRANTY

Recycling Information