EisSound KBSOUND PLUS, KBSOUND PLUS 42695, KBSOUND PLUS 42695U User Manual

28XW

E254006

USER’S MANUAL MANUAL DE USUARIO MANUEL DE L’USUAIRE

1 11 21

ENG

FOR KITCHENS & BATHROOMS

CC-1088-05.1

Before installingthe unit, pleaseread and followthe instructions providedin the InstallationManual included in this kit.

WARNING - Toreduce therisk of fire orelectric shock:

install in accordancewith themanufacturer’s instructions

do not exposethis apparatusto rainor moisture

do not usethis productnear water

do not attemptto dissamblethis unit

do not blockany ventilationopenings

do not install near any heat sources such as radiators, stoves or other equipment that produce heat.

Youare cautioned thatany changes ormodifications notexpressly mentioned inthis manual couldvoid your authority to operatethis equipment.

When used as a mechanism to disconnect from the current network, a socket plug, or a device connector; the disconnecting mechanism must be easily accessible at all times. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessoriesspecified bythe manufacturer.

as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Before operating the unit, please read thoroughly and follow the instructions provided in the User's Manual and save itfor futureuse.

This producthas been designed and tested to provide reasonable protection against harmful interference in residential installation. However there is no guarantee that interference will not have an affect it in a particular installation. In these cases, reorient the receiving antenna, try toincrease the separation between the equipment and the source of interference and/or connect the equipment into an outlet on a circuit different from thatto which the sourceof interference is connected.

The entire riskof theinstallation, use,results andperformance are the user'sresponsability.

Use a certified technician for installation, repair and/or maintenance of this equipment and comply with all the regulationsin force ineach country. Servicing is required whenthe apparatushas been damagedin any way, such

To change the batteries remove the cover pressing on the tab while lifting the cover. Use batteries type AAA 1,5V. Do not discard used batteries with household waste

1. Introduction

2. General Operating Notes

3. Operating Audio Functions

5. Selecting Turn-On Mode

4. Operating the FM Tuner

6. “Ideal” mode

4.1 Station Search

4.2 Directly Keying Station Frequency

4.3 Tuning to FM Memory Pre-Sets

4.4 Storing and Clearing Station Frequencies Manually

4.5 Storing and Clearing Station Frequencies Automatically

4.6 Adjusting StationSearch Sensitivity

CAUTION

DO NOT OPEN

RISK OF ELECTRIC SHOCK

Technical Specifications

42695 , 42695U MIN NORMAL MAX COMMENTS

Measurements 181x50x52 mm Voltage 120 Vac 60Hz Consumption demand 10 W terminals L,N Output signal (16 ohms) 1,5 W terminals D,I Passband 20 15.000 Hz Distortion 0,1 0,4 % Frequency range 87,5 108 MHz Antenna impedance 75 ohms terminals A,M Antenna sensitivity 3,5 5 uV Tuner distortion 2 % Number of station pre-sets 20

7. Play your iPod through KBSOUND® ®PLUS

Quick Reference Guide

ENG

Important Safety Instructions

ENG

CC-1088-05.1

Delete FM tuning pre-set

Delete all FM tuning pre-sets

Store all FM stations detected

Store FM station pre-set

DEL all

PRG all

5”

Automatic FM station search sensitivity

5”

321

Store “IDEAL” setting

PRG

2”

Store turn-on mode (on/off)

5”

DEL mem

PRG mem

2”

5”

Quick Reference Guide

SCAN

VOL VOL

TREBLE

BASS

MEM

LOUD

M/ST

DEL mem

DEL all

PRG mem

PRG all

PRG

2 3

SCAN

VOL VOL

Mute

Numeric Keypad

FM memory pre-sets

“IDEAL” mode

Bass Control

Treble Control

Clear

Directly keying FM station fre

Loudness

Volume Control

Automatic FM station search

Forced mono

(95.8MHz)

On/Off

CC-1088-05.1



Ergonomic remote control unit Loudspeakers the size of a halogen light (2”) 1,5W+1,5W power Does not require external power supply Ability to directly key in desired station frequency Ability to automatically store into memory stations

received with the best quality 20 memory pre-sets ”Intelligent” loudness: automatic adjustment to the

signal volume

Introducing , a sound device especially designed for easy and quick installation, without building work, cabling or pre-installations involved. Simple and easy to use, all system functions can be operated remotely by using a fully equipped remote control, eliminating the need to physically approach the control unit.

Blending perfectly into the décor of the kitchen or bathroom, the device has the following basic characteristics:

KBSOUND®PLUS

The components supplied in this kit are for installation and use in the manner and for the purpose described in the installation manual and the user manual. The installation must also comply with each country's current regulations. This manual assumes that the unit has been correctly installed and is fully operational.

If the device has not been installed yet, follow the instructions provided in the Installation Sheet included in this kit.

KBSOUND®PLUS

1. Introduction

ENG

CC-1088-05.1

1.- None of the functions (except ON/OFF) work unless the remote control is in “on” mode.

2.- Functions pertaining to operating the audio signal only work when “mute” is cancelled.

3.- The LED on the data receiver can change color depending on the control unit's mode:

OFF the control unit is off GREEN the unit is on RED the unit is receiving data from the remote control

4.- When activating or canceling a function (loudness, stereo/mono or mute):

4 RED flashes: function is cancelled

£ £ £

11RED flashing: function is activated

5.- The mains plug is used as the disconnect device so, once the is connected to the mains, it will remain powered

even if it is in the OFF state. That means that the OFF state (as indicated in this manual) really means a “standby” state

KBSOUND®PLUS

2. General Operating Notes

The control unit generates sound signals to communicate the status of operations carried out. These signals are reflected in this manual as follows:

A short BEEP sound signal indicates that the data was received.

A long BEEP sound signal indicates that an operation was correctly completed.

A series of BEEP sound signals indicates that a clearing operation was executed or that there is an error.

A BO BEEP sound signal indicates that the memory pre-set station tuned at the moment is station number one, or that the tuner's frequency is set at

87.5 MHz (the lowest on the dial).

Certain operations require a remote control key to be held down for a certain amount of time. This is indicated in the manual by a hand symbol next to the key.

BEEP

BEEP BEEP BEEP

Symbols Used in this Manual

CC-1088-05.1

3. Operating Audio Functions

Increase/decrease in the signal volume: The LED will flash

between RED and GREEN to indicate the desired change in volume.

When the maximum/minimum level is reached, the LED will stay lit

and be GREEN.

Increase/decrease in bass/treble levels: The LED will flash between

RED and GREEN to indicate the desired change in the bass/treble

levels. When the maximum/minimum level is reached, the LED will

stay lit and be GREEN.

Mute: If the unit becomes silent (mute activated), the LED will flash

once in RED. If the mute function is cancelled, the LED will flash four

times.

Loudness: It reinforces the bass level in terms of the signal volume, assuming a greater

backing at a lower volume and a lesser backing at a higher volume. The LED will flash once in

RED if the loudness has been activated (backing) or four times if it is cancelled.

Mono/stereo reception: When activated, this feature allows the FM stations to be received in stereo (the LED will flash

once in RED). When cleared, this feature only allows for mono reception (the LED will flash four times in RED).

Note: If the control unit's configuration is mono (see Installation Sheet supplied with this kit), the signal will always be

received in mono even if the signal received by the antenna is in stereo.

If the control unit is off, a brief press on the will

gradually turn on the unit (between 1 and 2 seconds).

While the unit is gradually turning on/off, the LED will be RED.

Once the control unit is ready to receive additional commands from

the remote control, the LED will be GREEN.

When the control unit is off, the LED will be OFF.

ON/OFF key

Key Sequence

VOL VOL

TREBLE

BASS

LOUD

M/ST

The will turn on

with the audio and station

frequency settings saved as “ideal”

mode settings (see chapters 5 and

6) when the unit is connected to the mains.

When switched off and on while connected to the mains, the audio and station frequency settings will

be as when the unit was switched

off with the remote control

ON/OFF key

KBSOUND®PLUS

ENG

CC-1088-05.1

Key Sequence Sound Signal

To directly key in an FM station frequency, sequentially press the numeric keys of the

station frequency then press the FM key. For example, to select 94.7, press 9 4 7 FM.

Each correctly entered digit will be followed by a BEEP sound signal and a RED LED flash.

Note: A station frequency can be keyed in as either 94.7 (9 4 7 FM) or as 94.70 (9 4

7 0 FM).

If the frequency keyed in is not correct or if more digits than necessary are keyed in, the

error will be noted with a BEEP-BEEP-BEEP-BEEP type signal.

To clear a digit keyed in and start keying in a different frequency, press the C key and

then begin keying in the desired frequency.

BEEP

BEEP BEEP BEEP BEEP

4.2 Directly Keying Station Frequency

While the search is taking place, the LED will be RED.

Once the station has been found, the LED turns GREEN.

When the search is going “up” the tuner, a BO BEEP signal sounds when the end of the

frequency range is reached. The next press of the key will start the search from the

beginning of the frequency range (87.5 MHz).

4.1 Station Search

BEEP

When the search is going “down” the tuner, a BO BEEP signal sounds when the beginning

of the frequency range is reached. The next press of the key will start the search from the

end of the frequency range (108.0 MHz).

BEEP

4. Operating the FM Tuner

BIP

BIP BIP BIPBIP

SCAN

CC-1088-05.1

4.4 Storing and Clearing Station Frequencies Manually

Key Sequence Sound Signal

To , tune to the station (see Chapters 4.1. Station Search and

4.2. Directly Keying Station Frequency). Hold down the FM key for 2”. The station tuned at that time will be stored in the memory.

store a station in memory

If all the memory slots have been assigned, the current station will not be able to be

stored and the sound signal and LED will be the same as when there is an error.

To , select the station and hold down the C key for 2”. The

station tuned at that time will be cleared from memory if it was previously stored.

delete a station from memory

If the station you wish to clear from memory was not previously stored in the memory, the

sound signal and LED will be the same as when there is an error.

BEEP

BIP

The MEM+/MEM- keys allow you to scroll through the stations stored in memory (see

Chapters 2.6 and 2.7, Storing and Clearing Stations in Memory).

When stations are stored in memory they are sorted in ascending order; that is, beginning

with 87.5 and ending with 108.0.

When memory n# 1 is called up, the typical BO-BEEP audio signal sounds.

BEEP

4.3 Tuning to FM Memory Pre-Sets

If there are no stations stored in memory, the sound signal and LED will be the same as

when there is an error.

BEEP BEEP BEEP BEEP

MEM

PRG mem

2’’

PRG mem

2’’

DEL mem

2’’

DEL mem

2’’

ENG

CC-1088-05.1

Key Sequence Sound Signal

To activate the process for all the memory slots,

hold down 6 key for 5”.

clearing station frequencies automatically

To activate the process, hold down key 9 for 5”.

While the key is held down, the LED will be RED. Once the operation to scan stations has

begun, the LED will alternately flash between GREEN and RED.

The control unit will store into memory the stations that are received with the highest

quality, ordered from lowest frequency (87.5 MHz) to highest frequency (108.0 MHz).

The system will use all the memory slots available, reaching the maximum of 20.

The process can take a few moments. Once the scan has been completed or once the

maximum number of memory slots has been used, the process ends and a long BEEP

signal sounds.

storing station frequencies automatically

BEEP

5’’

PRG all

5’’

DEL all

4.5 Storing and Clearing Station Frequencies Automatically

To adjust the automatic station search sensitivity (see 4.1. Station Search), hold down the

1 and 3 keys (1=minimum, 3= maximum) for 5”. While the key is held down, the LED

will be RED. A BEEP sound signal will indicate that the new level of sensitivity has been

correctly stored.

4.6 Adjusting Station Search Sensitivity

BEEP

5’’

CC-1088-05.1

5. Selecting Turn-On Mode

ENG

This function is designed for use in the event that the power supply is fed by a specifically designated switch. In this case, the automatic activation mode must be programmed in order to automatically turn on the unit when the switch is activated. These steps must be followed:

KBSOUND®PLUS

1. Supply power to the unit byflicking the switch.

2. The unit willflicker acouple of times and turn off.

3. Turn on the unit using the remote control (ON/OFF key).

4. With the unit turned on, keep the ON/OFF key pressed down for 5”.

KBSOUND®PLUS

If the Turn-On mode is set to “on”, the RED light will flash once. In this state, when power is fed to the unit, it will turn on in “ideal” mode (see Chapter

6. “Ideal Mode”).

If the Turn-On mode is set to “off”, the RED light will flash four times. In this state, when power is fed to the unit, it will turn on in “off” mode.

BIP

5’’

Key Sequence

Sound Signal

CC-1088-05.1

+ 22 hidden pages

EisSound KBSOUND PLUS, KBSOUND PLUS 42695, KBSOUND PLUS 42695U User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual