EisSound KBSOUND, KBSOUND 42697, KBSOUND 42697U User Manual
USER’S MANUAL
MANUAL DE USUARIO
MANUEL DE L’USUAIRE
1
11
21
ENG
E
F
CC-1146-01.1
1
Important Safety Instructions
Before installingthe unit, pleaseread and followthe instructions providedin the InstallationManual included
in this kit.
Before operating the unit, please read and follow the instuctions provided in this User´s Manual thoroughly
and save itfor futureuse
WARNING - Toreduce therisk of fire orelectric shock:
install in accordancewith themanufacturer’s instructions
do not exposethis apparatusto dripping and splashing
do not usethis productnear water
do not attemptto dissamblethis unit
do not blockany ventilationopenings
do not install near any heat sources such as radiators, stoves or other equipments that produce
heat.
Youare cautioned thatany changes ormodifications notexpressly mentioned inthis manual couldvoid your
authority to operatethis equipment.
This producthas been designed and tested to provide reasonable protection against harmful interference in
residential installation. However there is no guarantee that interference will not havean affectin a particular
installation. In these cases, reorient the receiving antenna, try to increase the separation between the
equipment and the source of interference and/or connect the equipment into an outlet on a circuit different
from that towhich thesource ofinterference isconnected.
The entire riskof theinstallation, use,results andperformance are borne byyou.
When used as a mechanism to disconnect from the current network, a socket plug, or a device connector;
the disconnecting mechanism must be easily accessible at all times. Protect the power cord from being
walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessoriesspecified bythe manufacturer.
as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to dripping and splashing, does not operate normally, or has
been dropped.
Use a certified technician for installation, repair and/or maintenance of this equipment and comply with all
the regulationsin force ineach country. Servicing is required when the apparatus has been damagedin any
way, such
To change the batteries remove the cover pressing on the tab while lifting the cover. Use
batteries type AAA 1,5V. Do not discard used batteries with household waste
2
10
3
4
5
6
9
10
1. Introduction
2. General Operating Notes
3. Operating Audio Functions
5. Selecting Turn-On Mode
4. Operating the FM Tuner
6. “Ideal” mode
Quick Reference Guide
4.1 Station Search
4.2 Directly Keying Station Frequency
4.3 Tuning to FM Memory Pre-Sets
4.4 Storing and Clearing Station Frequencies Manually
4.5 Storing and Clearing Station Frequencies Automatically
4.6 Adjusting StationSearch Sensitivity
Table of Contents
CAUTION
DO NOT OPEN
RISK OF ELECTRIC SHOCK
!
ENG
7. Play your iPod through® ®KBSOUND
Technical Specifications
42697,42697U MIN NORMAL MAX COMMENTS
Measurements 181x50x52 mm
Voltage 120 Vac 60Hz
Consumption demand 10 W terminals L,N
Output signal (16 ohms) 1,5 W terminals D,I
Passband 20 15.000 Hz
Distortion 0,1 0,4 %
Frequency range 87,5 108 MHz
Antenna impedance 75 ohms terminals A,M
Antenna sensitivity 3,5 5 uV
Tuner distortion 2 %
Number of station pre-sets 30
CC-1146-01.1
PGR ON/OFFPRG ON/OFF
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
DEL MEM
C
DEL MEM
C
DEL MEM
C
DEL MEM
C
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
1
3
1
2
3
1
3
1 2 3
2
Quick Reference Guide
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
PGR ON/OFF
1
2
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
SCAN
SCAN
PRG ON/OFF
1 2 3
4
5
6
7 8
9
DEL ALL
PRG ALL
DEL MEM
PRG MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
Numeric Keypad
FM memory pre-sets
Automatic FM station search
Delete FM tuning pre-set
Delete all FM tuning pre-sets
Store all FM stations detected
Store FM station pre-set
Automatic FM station
search sensitivity
Store “IDEAL” setting
Store turn-on mode (on/off)
Mute
”IDEAL” mode
Clear
Loudness
Audio level control
volume/bass/treble/balance
Select +/- keys function
volume/bass/treble/balance
Forced mono
On/Off
Directly keying
FM station frequency (i.e. 95.8 MHz)
1”
5555
888
8
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
5”
5”
2”
5”
2”
5”
5”
1”
CC-1146-01.1
IR receiver/transmitter
Loudspeakers
1.5W+1.5W power
Sound device with built-in FM tuner (does not
require an external power supply)
Remote control:
Display screen that visualizes the functions
Volume, bass, treble and balance control
'Forced Mono' function
Ability to directly key in desired station
frequency
Ability to automatically store into memory
stations received with the best quality
30 memory pre-sets
“Intelligent” loudness: automatic adjustment
to the signal volume
4
4
4
4
4
4
4
Introducing , a sound device especially designed for easy and quick installation, without
building work, cabling or pre-installations involved. Its three components (remote control, loudspeakers,
and electronic device) provide an FM tuner that perfectly blends into the kitchen or bathroom décor
installed in the furnishings.
KBSOUND®
Its operation is simple and easy by using a remote control unit with a display screen. The screen displays
constant information about the state of the sound device installed in the ceiling, such as station frequency
tuned, volume, bass, treble, etc.
3
1. Introduction
Blending perfectly into the décor of the kitchen or bathroom, the kit provides the following
features:
KBSOUND®
ENG
The components supplied in this kit are for installation and use in the manner and for the purpose described in the
installation manual and the user manual. The installation must alsocomply with each country's current regulations.
This manual assumes that the unit has been correctly installed and is fully operational. If the device has not been installed yet,
follow the instructions provided in the Installation Sheet included in this kit.
KBSOUND®
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
PGR ON/OFF
1
2
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
SCAN
SCAN
PRG ON/OFF
1 2
3
4
5
6
7 8
9
DEL ALL
PRG ALL
DEL MEM
PRG MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
CC-1146-01.1
1.- None of the functions (except ON/OFF) work unless the remote control is in “on” mode.
2.- Functions pertaining to operating the audio signal only work when “mute” is cancelled.
Once the is connected to the mains, it will remain powered even it is in OFF state. That
means that the OFF state (as indicated in this manual) really means a “standby” state
®3.-
KBSOUND
4.-
5.- The remote control unit exchanges information (transmits and
receives data) by means of the transmission-reception capsule. If
at any time there is a failure in the synchronicity of communication,
the screen will display the symbol. In the event of this
occurring, point the remote control to the transmission-reception
capsule at a straight-line distance of no greater than 5 meters.
6.- The remote control display will
automatically turn off when there has been
no keying activity for more than a few
seconds, ensuring more efficient battery
usage. To view the display information at
any time, point the remote control to the
transmission-reception capsule and press
the key.
A short BEEP sound signal indicates that the data was received
7.- To illustrate that an
operation requires holding
down a key on the remote
control for a specific amount of
time, the symbol will
appear in the manual next to
the key.
BIP
4
The will turn on
with the audio and station
frequency settings saved as
“ideal” mode settings (see
chapters 5 and 6) when the
unit is connected to a power
supply.
When switched off and on
while connected to the
power supply, the audio and
station frequency settings
will be as when the unit was
switched off with the remote
control ON/OFF key
®
KBSOUND
2. General Operating Notes
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
PGR ON/OFFPRG ON/OFF
5m
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
PGR ON/OFF
1
2
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
B
AL
LOUD
MUTE
M/ST
102.50
SCAN
SCAN
1
3
4
5
6
7
8
9
DEL ALL
PGR ALL
DEL MEM
PGR MEM
0
C
FM
VOL
BASS/
TREBLE
BAL
LOUD
MUTE
M/ST
SCAN
SCAN
PRG ON/OFF
1 2
3
4
5
6
7 8
9
DEL ALL
PRG ALL
DEL MEM
PRG MEM
0
C
FM
VOL
BASS/
TREBLE
B
AL
LOUD
MUTE
M/ST
CC-1146-01.1
Key Sequence Display
Increase/decrease in the signal volume: The LED will
flash to indicate the desired change in volume.
Increase/decrease in bass/treble levels: The
LED will flash to indicate the desired change in the
bass/treble levels.
Mute: the unit becomes silent (mute activated)
Loudness: It reinforces the bass level in terms of the signal volume, assuming a
greater backing at a lower volume and a lesser backing at a higher volume.
Mono/stereo reception: When activated, this feature allows the FM stations to be received in
stereo. When cleared, this feature only allows for mono reception.
Note: If the control unit's configuration is mono (see Installation Sheet supplied with this kit), the
signal will always be received in mono even if the signal received by the antenna is in stereo.
If the control unit is off, a brief press on the will gradually turn on the unit
(between 1 and 2 seconds).
When the control unit is off, the LED will be OFF.
ON/OFF key
The LED will display the word “ON”
5
ENG
3. Operating Audio Functions
on
vol 58
BAS+06
MUTE
LD on
STEREO
PGR ON/OFFPRG ON/OFF
BASS/
TREBLE
BASS/
TREBLE
BASS/
TREBLE
BASS/
TREBLE
LOUD
LOUD
LOUD
LOUD
MUTEMUTEMUTEMUTE
M/ST
M/ST
M/ST
M/ST
CC-1146-01.1
6
4. Operating the FM Tuner
Key Sequence Display
To directly key in an FM station frequency, sequentially press the numeric keys of the
station frequency then press the FM key. For example, to select 94.7, press 9 4 7 FM.
Note: A station frequency can be keyed in as either 94.7 (9 4 7 FM)
or as 94.70 (9 4 7 0 FM)
If the frequency keyed in is not correct or if more digits than necessary are keyed in, the
screen will display the word “ERROR”
To clear a digit keyed in and start keying in
a different frequency, press the C key
and then begin keying in the desired
frequency
4.2 Directly Keying Station Frequency
While the search is taking place, the word “SCAN” will appear on the display screen.
The screen will duly display the station frequency of the next station located.
4.1 Station Search
1”
94.70
94.70
ERROR
FM
FM
SCAN
102.50
FM
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
4444
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
4444
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
4444
5555
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
111
1
4444
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
DEL MEM
C
DEL MEM
C
DEL MEM
C
DEL MEM
C
CC-1146-01.1
Key Sequence Display
4.4 Storing and Clearing Station Frequencies Manually
To , tune to the station (see Chapters 4.1. Station Search and 4.2.
Directly Keying Station Frequency).
Hold down the FM key for 2”.
The station tuned at that time will be stored in the memory.
If all the memory slots have been assigned, the current station will not be able to be stored and
the screen will display the word "NO MEM"
store a station in memory
To , select the station and hold down the C key for 2”. The station
tuned at that time will be cleared from memory if it was previously stored.
If the station is not stored in memory, the screen will display the word "NO MEM"
delete a station from memory
The SCAN keys allow you to scroll through the stations stored in memory (see Chapters 2.6 and
2.7, Storing and Clearing Stations in Memory).
When stations are stored in memory they are sorted in ascending order; that is, beginning with
87.5 and ending with 108.0.
The screen will display the frequency of the station saved to that memory pre-set.
If there are no stations stored in memory, the screen will display the word "NO MEM"
4.3 Tuning to FM Memory Pre-Sets
7
ENG
MEM 07
DEL OK
MEM 19
102.50
FM
2’’
2’’
94.70
FM
94.70
FM
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
SCAN
4444
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
PGR MEM
FM
PGR MEM
FM
PGR MEM
FM
PRG MEM
FM
DEL MEM
C
DEL MEM
C
DEL MEM
C
DEL MEM
C
CC-1146-01.1
8
Key Sequence Display
To activate the process for all the
memory slots, hold down 7 key for 5”.
clearing station frequencies automatically
To activate the process, hold down key 9 for 5”.
When the automatic programming begins the screen will display the word “AUTO” .
The control unit will store into memory the stations that are received with the highest quality,
ordered from lowest frequency (87.5 MHz) to highest frequency (108.0 MHz).
The system will use all the memory slots available, reaching the maximum of 30.
The process can take a few moments. Once the scan has been completed or once the
maximum number of memory slots has been used, the process ends and a BEEP signal
sounds.
storing station frequencies automatically
4.5 Storing and Clearing Station Frequencies Automatically
To adjust the automatic station search sensitivity (see 4.1. Station Search),
hold down the 1 and 3 keys (1=minimum, 3= maximum) for 5”
4.6 Adjusting Station Search Sensitivity
AUTO
SENS 2
BIP
5’’
5’’
5’’
5’’
AUTO
9
PGR ALL
9
PGR ALL
9
PGR ALL
9
PRG ALL
333
3
2
2
111
1
7
DEL ALL
7
DEL ALL
7
DEL ALL
7
DEL ALL
DEL MEM
5’’
CC-1146-01.1
9
ENG
5. Selecting Turn-On Mode
If the Turn-On mode is set to
“on” in this state, when
power is fed to the unit, it will
turn on in “ideal” mode (see
Chapter 6. “Ideal Mode”).
If the Turn-On mode is set to “off”,
when power is fed to the unit, it will
turn on in “off” mode.
This function is designed for use in the event that the power
supply is fed by a specifically designated switch. In this case, the automatic
activation modemust be programmed inorder to automatically turn on the
unit when the switch isactivated.
These steps must be followed:
®
®
KBSOUND
KBSOUND
1. Supply power to the unit by flicking the switch.
The unit will flicker a coupleof timesand turn off.
2. Turn on the unit using the remote control (ON/OFF
key).
3. With the unit turned on, keep the ON/OFF key
pressed down for 5”.
®
®
®
®
KBSOUND
KBSOUND
KBSOUND
KBSOUND
Key Sequence Display
AUTO x
5’’
5’’
PGR ON/OFFPRG ON/OFF
PGR ON/OFFPRG ON/OFF
CC-1146-01.1
Loading...