EisSound 42691/A1 User And Installation Manual

USER’S AND INSTALLATION MANUAL

42691/A1 CONTROL UNIT

CC-1035ENG-09

1

1. Introduction

2. Getting started

3. Installation

5. User Programming

8. Technical Specifications

4. Settings

7. Quick Reference Guide

6. Operation

9. Accesories

Wiring Diagram

3

4

7

9

24

11

25

15

26

2

Important Safety Instructions

Before installing the unit, please read and follow the instructions provided in the
Installation Manual included .

Before operating the unit, please read and follow the instuctions provided in the User´s
Manual thoroughly and save it for future experience.

WARNING -To reduce the risk offireorelectricshock:

install in accordance with the manufacturer’s instructions

do not expose this apparatus to rain or moisture

do not use this product near water

do not attempt to dissamble this unit

do not block any ventilation openings

do not install near any heat sources such as radiators, stoves or other
equipments that produce heat.

You are cautioned that any changes or modifications not expressly mentioned in this
manual could void your authority to operate this equipment.

This product has been designed and tested to provide reasonable protection against
harmful interference in residential installation. However there is no guarantee that
interference willnot affect ina particular installation. Inthese cases, reorient the receiving
antenna, try to increase the separation between the equipment and the source of
interference and/or connect the equipment into an outlet on a circuit different from that to
which the source of interference is connected.

The entire risk of the installation, use, results and performance are borne by you.

When used as a mechanism to disconnect from the current network, a socket plug, or a
device connector; the disconnecting mechanism must be easily accessible at all times.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

as power-supplycord or plugis damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,or has been dropped.

Attention should be drawn to the environmental aspects of battery disposal.

Use a certifiedtechnician for installation, repair and/or maintenance of this equipment and
comply with all the regulations in force in each country. Servicing is required when the
apparatus hasbeen damaged inany way,such

CAUTION

DO NOT OPEN

RISK OF ELECTRIC SHOCK

!

CC-1035ENG-09

2

Wiring diagram

CONNECTING TERMINALS

15Vdc Sound regulator power supply

Mass

2

4

05

06
04

N

L

Left loudspeaker output (red terminal/+)
Right loudspeaker output (red terminal/+)

Common loudspeaker ouput (black terminals/-)

230V Power supply

FM tuner antenna signal
FM tuner antenna mass

A
M

+

-

0506 4M 04 2

+

-

A

CONTROL UNIT

CH FM

PRG

3

6

9

def

mno

wxyz

1

4

7

ghi

pqrs

2

5

8

0

C

abc

jkl

tuv

76 cm

16 W

+

-

16 W

+

-

Rojo Negro

4 2

N L

LN

NegroRojo

426 91
426 A1

112 98

230V

It isadvisable that the directcurrent that provides powerto the power supply(ref.11298) beconnected to a specificAutomatic Switch in order to isolateand
allow youto disconnect theAudio System independently from therest of theelectrical appliances in thehome. Other devices such as smokeextractors, air
conditioning units, fridges and ventilators can negatively affect the reception of the FM signal and produce noises on the audio lines.

CC-1035ENG-09

3

1. Introduction

The new is here. It provides the finest features offered by the

400 Series, available in the convenient form of a kit.

Like the 400 Series, the is user-friendly in design. Its clear and
easily accessible menus allow the user to failor the settings according to the needs of each
client. The direct FM tuning, the adjustable lighting, the screen with bigger letters and
numbers, the choice of language, etc. are just some of the functions available in this
customer-centered design.

42691/426A1 control unit

EISSOUND

42691/426A1 control unit

What else does the offer? It was designed for people who want to enjoy sound in radio or music in
areas of the home with no television or stereo system, no sound pre-installation and who have no desire to undergo major improvements.

The is the ideal accessory to enjoy the best possible sound in the kitchen and bathroom by means of a control unit
that blends right into the decor.

As always and with the

42691/426A1 control unit QUALITY

42691/426A1 control unit

42691/426A1 control unit THE CUSTOMER ONLY HAS TO LISTEN.

The symbol over a key
means the key should be pressed
for the time specified

Some keys serve the function of a cursor to scroll through
the menus. When the key in question is used as a cursor,
it will be illustrated with the cursor symbols that appear
on the face of the control unit.

2

54

8

6

abc

jkl

ghi

tuv

mno

In some cases it will be necessary
to press two keys simultaneously
to execute a
particular
command.

2’’

PRG

KEYS TO UNDERSTANDING THE SYMBOLS

USED IN THIS MANUAL

5’’

CC-1035ENG-09

To turn on, press the on/off key. The display will light up and

the icon enabled.

To select discman/MP3/iPod input for the control unit, press

4

9

wxyz4ghi7pqrs

FM

94.70

Users

Once the control unit has been installed it is ready for normal
operation.
Once the control unit is connected to the mains, it will remain
powered even it is in OFF state. That means that the OFF state
(as indicated in this manual) really means a “standby” state

2.1 The first time...

Installers

The control unit must be installed once power is fed for the first
time. By default, the control unit is set to stereo for 16
loudspeakers. To configure other settings use the installation
menu option 3.2.1. - Mono/Stereo and 3.2.2. - Audio Output.

W

Key Sequence Display Visual

07:18

CH

vol 55

96.70

To adjust the volume

To select the tuner, press FM

To tune to a station, key in the station frequency followed by

the FM key. For example, to tune to the station at 94.7 MHz.

To automatically seek stations

The + - keys have multiple functions. The default function is to adjust the
volume. If no key is pressed on the keypad a few seconds after an
operation, the default function resumes.

FM

95.50

FM

2. Getting Started

CC-1035ENG-09

5

Key Sequence Display Visual

instal

Installation Menu

This menu stores information regarding the parameters that affect the installation's proper
operation. This programming should be done by a specialized technician.

There are three menus to program different access levels.

2.2 Programming Menus

2.2.1 Three Access Levels

2’’

PRG

PRG

2’’

PRG

Configuration Menu

This menu stores information regarding the personalized operating mode for each user.
Modifying this menu does not vitally affect the installation's operation and once the settings
are defined there will be no need to change them.

Programming Menu

This menu stores information regarding the features that can be programmed by the user
and which can be easily modified.

config

progr

The programming menus are structured as levels of menus and submenus.

Once in a menu, the following keys can be used to scroll
through the list of options.

2.2.2 Scrolling Through the Menus

Goes back to the previous option on the same level

Goes into the level

Exits the level

Goes forward to the next option on the same level

21

54

8

7

0

C

3

6

9

abc

jkl

ghi

pqrs

tuv

def

mno

wxyz

CC-1035ENG-09

6

When the item to be programmed appears on the display it will be

flashing, thus indicating it is ready to be modified. If there are several

choices possible (for example, the days of the week, the digits of a date),

the + and - keys can be used to scroll back and forth between the items.

Key Sequence Display Visual

PRG

0

C

1’’

The numeric keys can also be used to modify the item. In addition to using

the numeric keys, in some cases the + and - keys themselves can be used

to modify an item to be programmed.

To store the new setting, press PRG. The item will flash quickly, indicating

that the new setting has been stored.

To delete a setting that has been entered, press the ZERO key for 1”.

To exit a programming option without saving a setting, press ON/OFF.

PRG

2

abc

1

2

abc

PRG

2’’

To access programming menu option “adjust the tuner seek sensitivity”

To access the configuration menu option “personalize your greeting”

To access the installation menu option “select loudspeaker output

impedance”

2.2.3 Immediate Access to a Menu Option

As an alternative to scrolling through the menus to reach an option, you can directly key in
the option code followed by the menu access key (see the list of codes in 7. CODES AND
TABLES).

2

abc

PRG

2’’

CC-1035ENG-09

7

3.1 Wiring Diagram

·

·

·

·

·

If the room is monophonic, connect any of the speakers and set the control unit to MONO. (See 3.2.1. Mono/Stereo Installation)
8 speakers can be connected to the control unit outputs. In this case, the control unit must be set to 8 . (See 3.2.2. Audio Output
Installation).
To connect the FM antenna, connect a 76 cm wire to terminal A or connect a 75 antenna input to terminals A (signal) and M (mass).
If it is necessary to connect an amplifier or power stage to a control unit's output, the control unit must be set to AMPLIFIER. (See 3.2.2.
Audio Output Installation). Connect the amplifier to terminals 2, 4, 05 and 06 on the control unit.
All wire sections are 0.25 mm except supply wires (terminals 2 and 4), which are 1 mm. The network tapping wires are standard.

W W

W

Installation involves three elements: a power supply, a control unit and loudspeakers. See on page 3.

3.2.1 Mono/Stereo

Defines whether the control unit's audio output (terminals 04, 05, 06) is connected in
mono or stereo mode. In a control unit in stereo, outputs 05 and 06 respond to the left
and right channels. In a control unit in mono, both outputs are identical and can
therefore be used interchangeably.

To change the output setting to mono

Store

Key Sequence Display Visual

stereo/mono

stereo

mono

2

abc

PRG

2’’

PRG

3.2 Installation Menu

The following information is, in its totality, the installation data for the control unit. To
modify the data, access the installation menu of the control unit itself.
See 7. CODES AND TABLES.

1

3. Installation

CC-1035ENG-09

8

Key Sequence Display Visual

on

loading data

2

abc

PRG

delete installation

off

version soft

software, 112702, 141211

Shows control unit’s software version.

3.2.3 Deleting Control Unit Installation. Manufacturer Reset.

3.2.4 Knowing the Software Version

Deletes all settings and programming data from the control unit, restoring manufacturer
default settings.

Once the control unit starts up, the manufacturer default settings are enabled.

To activate delete process

To initiate the process

2’’

PRG

2’’

PRG

3

def

4

ghi

16

8

3.2.2 Audio Output

Defines the impedance connected to the control unit's audio output (terminals 04, 05, 06)
between the following options:

16 ohm passive loudspeaker
8 ohm passive loudspeaker
amplifier
line

To change the setting to 8 ohm

Store

audio output

2

abc

PRG

PRG

2’’

2

abc

CC-1035ENG-09