Page 1
Instruction Manual
PIPE - SNIPER
®
PIPE BELT GRINDER
Page 2
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
PIPE - SNIPER
®
PIPE BELT GRINDER
You have made a good decision to buy our Pipe Sniper ® Pipe Belt Grinder/Polisher. Thanks to the genuine 2/3
enclosure, it is possible to machine pipes completely (360 degrees) from one working position. The new 1,750
Watt motor allows you to tackle any professional application. The balanced handle allows the user to work in
every imaginable working position.
The Pipe Sniper ® pipe belt grinder guarantees, thanks to its sophisticated enclosure technology and
innovative gas-pressure damping system, reduced strain on the user.
Speed Settings
Easy, speed adjustment by simply using the knurled knob on the handle: 1,000-3,800 rpm. Level B, C
& D is the ideal speed setting for most belts and creates an especially clean and chatter mark free
finish.
When removing dirt and scratches the speed can be increased.
Levels D & E is suitable for polishing belts.
Levels B & C is suitable for grinding belts.
Speed Settings (approx. Speed):
E = 2,400 rpm
F = 2,900 rpm
G = 3,800 rpm
A = 1,000 rpm
B = 1,300 rpm
C = 1,900 rpm
D = 2,100 rpm
Application:
Foreword:
■ PIPE-SNIPER
®
for pipe diameter
¡ from 25 to 42 mm
with 2/3 enclosure
¡ up to 70 mm
with 1/2 enclosure
Page 3
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
PIPE - SNIPER
®
PIPE BELT GRINDER
Maintenance:
Changing the carbon brushes:
Unplug the machine from the power point, take out the screws and open the service hatch. Disconnect
the attached wires, remove the carbon brushes and clean the housing using an air
compressor. Put in new carbon brushes (This must not jam in the maintenance hatch) and put in
the spring back in. Lastly place the service hatch and the fasten screws back into place.
Through the air inlet slots it is possible to see if the brushes are on fire. If there is a strong fire the machine switches
off. To avoid causing more damage to the machine, we advise you to send it to us.
Only original replacement carbon brushes must be used. Our warranty is void if the incorrect carbon brushes are
used.
Cleaning:
Prevent the build-up of metal dust inside the machine by regularly blowing it out with an air compressor.
Gearbox:
The screws on the gearbox must not be loosened during the warranty period or this will void the warranty.
The grease in the gearbox needs to be renewed approximately after 1,500 hours. This is done by firstly, loosening
the screws then replacing the old grease with approximately 16g of gear grease.
Warranty:
We have a 12 month guarantee (from receipt date) from all technical and mechanical parts, as long as there was
no third party interference.
Technical Data
Mains Connection
220 V ~ 50 – 60 Hz
(alternative 110 V ~ 50 – 60 Hz)
Power Input 1,750 Watt (1,600 Watt)
Speed
Infinetely adjustable from 1,000 rpm up to
3,800 rpm , with tacho-generator for
constant speed under load.
Belt Dimensions
40 mm x 780 mm
Weight
5.3 kg
It is easy to change the carbon
brushes: Open the service hatch by
removing the screws, replace the old
carbon brushes, close the hatch and
fasten the screws.
Changing the carbon brushes easier and faster
1 2 3
TIP
Page 4
6
8
7
5
4
2
3
1
PIPE - SNIPER
®
Setting the required pipe diameter
Choose the correct position from 10 to 30mm for the pipe to
be processed.
Tip: To change the setting quickly remove the belt from the
mechanism beforehand.
1 2 3
Top quality synchronous
mechanism consisting of gear
wheels for wear-free pipe
enclosure.
New aluminum lever makes
enclosing the pipe extremely easy
with minimum force.
By simply adjusting the clamping
lever, the enclosure angle of the
return rollers can be adjusted to
any pipe diameter
4
Very compact, balanced design with
a handle bar to reduce strain on the
user and to allow grinding in any
position.
8
Exclusive from Eisenblätter:
Rubberised handle for optimal and
safe handling
TIP
75
Easy to operate speed control;
tacho-generator for constant
speed even under load.
QUICK-LOCK cable release for a
quick and easy change and for
storage.
6
PIPE BELT GRINDER
Details / Features:
Application / Handling:
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
º
º
Maintenance cover allows carbon
brushes to be easily accessed.
Page 5
PIPE - SNIPER
®
PIPE BELT GRINDER
Changing Belts
• Important: Only change belts with the motor turned off.
•
Tighten the T-Handle
•Put the belt onto the machine over the roller guides
•Release the T-Handle to fasten the belt
Tip: New grinding belts should be run without
pipe contact , then switch to the required
enclosure size!
Checking the Belt
• Turn on the machine and check whether the belt runs
perfectly.
Tip: Put speed level on 'A'!
• Turn the machine off
Your PIPE-SNIPER® is now ready.
Before grinding
Put the belt on the pipe
Use the T-Handle to enclose the pipe the desired
amount.
• Important: For safety guide the machine using both handles.
After grinding
Important: T-Handle must be released before
removing the machine!Remove PIPE-SNIPER®
from pipe
TIP
TIP
1
2
2
2
2
1
1
1
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
Grinding Belt Adjustment
• Roller shaft with spanner (SW 16)
hold it in place and then loosen the lever.
• Align the lever parallel to the arm
• Correct adjustment: The belt must fit exactly onto the roller,
readjust until ready.
• Important: The angle the machine must make to the workpiece is 90°degrees, so that
the belt remains optimally adjusted. Run the belt first to see if there is some deviation
from the default load.
Page 6
PIPE - SNIPER
®
PIPE BELT GRINDER
Total Price
Price per Piece
GritSizeProduct
Purchase order
Number
Amount
Delivery Address
Customer
Company:
Contact Person:
Street No.:
Post Code:
Telephone:
Fax:
Bestellung
Fax 08171 / 93 84-55
Page No.Delivery MethodDelivery TimeOrder DateCustomer No.
A.S.A.P.
2 = Pick Up
1 = DPD
3 = Forwarding
Not
Urgent
Total Price
Signiture
Subject to our delivery terms and conditions. as of 11/08.
Gerd Eisenblätter GmbH
Patented grinding and polishing technology · Jeschkenstraße 10 ·
D-82538 Geretsried Tel. +49 (81 71) 93 84 - 0 · Fax +49 (81 71) 93 84 - 55
www.eisenblaetter.de · e-mail: info@eisenblaetter.de
EIS EN BLATT E R
H i g h T e c h S c h l e i f - u n d P o l i e r t e c h n i k
Order by FAX: 08171 - 93 84 - 55
Page 7
PIPE - SNIPER
®
PIPE BELT GRINDER
CE 94 Declaration of conformity for PIPE-SNIPER
®
Gerd Eisenblätter GmbH Jeschkenstr. 10 DE-82538 Geretsried
CE 94 Anlage zur POLY-PTX®500
+
- Bedienu
ngsanleitung
ENGLISH NEDERLANDS
EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in conformity
with the following standards or standardization documents: EN 60745, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3 according to the provisions of the regulations 2006/42/EG, 2004/108/EG.
EC-KONFORMITEITSVERKLARING
Wij verklaren op eigen verantwoording, dat dit produkt voldoet aan de
volgende normen of normatieve dokumenten: EN 60745, EN 55014-1,
EN 55014-2, EN 61000-3-2, EN 61000-3-3 volgens de bepalingen van
de richtlijnen 2006/42/EG, 2004/108/EG.
DEUTSCH DANSK
CE-KONFORMITÄTSERKLÄRUNG
Wir erklären in alleiniger Verantwortung, dass dieses Produkt mit den
folgenden Normen oder normativen Dokumenten übereinstimmt: EN
60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 gemäß
den Bestimmungen der Richtlinien 2006/42/EG, 2004/108/EG.
CE-KONFORMITETSERKLÆRING
Vi erklæerer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende normer eller normative dokumenter: EN
60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 i henhold til bestemmelserne i direktiverne 2006/42/EG, 2004/108/EG.
FRANÇAIS NORGE
DÈCLARATION "CE" DE CONFORMITÉ
Nous déclarons sous notre propre responsabilité que ce produit est en
conformité avec les normes ou documents normalisés: EN 60745, EN
55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 conformément aux
termes des réglementations
2006/42/EG, 2004/108/EG.
CE-ERKLÆRING AV KONFORMITET
Vi overtar ansvaret for at dette produktet er i overenstemmelse med følgende standarder eller standard-dokumenter: EN 60745,
EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 i samsvar med
bestemmelsene i direktivene 2006/42/EG, 2004/108/EG.
ITALIANO SVENSKA
DICHIARAZIONE DI CONFORMITÀ CE
Assumendone la piena responsabilità, dichiariamo che il prodotto è conforme alle seguenti normative ed ai relativi documenti: EN 60745, EN
55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 in base alle prescrizioni delle direttive 2006/42/EG, 2004/108/EG.
CE-KONFORMITETSFÖRKLARINGEN
Vi intygar och ansvarar för att denna produkt överensstämmer med
följande norm och dokument: EN 60745, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3 enligt bestämmelserna i riktlinjerna 2006/42/
EG, 2004/108/EG.
ESPAÑOL SUOMI
DECLARACION DE CONFORMIDAD CE
Declaramos bajo neustra sola responsabilidad que este producto está en
conformidad con las normas o docu-mentos normalizados siguientes : EN
60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 de acuerdo con las regulaciones
2006/42/EG, 2004/108/EG.
TODISTUS CE-STANDARDINMUKAISUUDESTA
Todistamme täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen standardien ja standardoimisasiakirjojen vaatimusten mukainen: EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3
seuraavien ohjeiden määräysten mukaisesti: 2006/42/EG,
2004/108/EG.
PORTUGUES GREEK
DECLARAÇÃ0 DE CONFORMIDADE CE
Declaramos sob nossa exclusiva responsabilidade que este producto
cumpre as seguintes normas ou documentos normativos : EN 60745, EN
55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 de acordo com as
disposições das directivas 2006/42/EG, 2004/108/EG.
∆΄HΛΩ∑Н ∑ΥМΒΑΤΙΚ΄ОΤΗΤОΣ
∆ηλώvoυμε υттεuθύvως óт тo проїóv αuтó εіvα καтασκεuασμέvo
ơúμφωvα µε тоuς εξής καvovισµοúς ή καтαơкεuασтκές σuσтάσες: EN
60745, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3
σúμφωνα με тς
δαтάξες тων Οδηуών: 2006/42/EG, 2004/108/EG.
Gerd Eisenblätter GmbH
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
Page 8
PIPE - SNIPER
®
PIPE BELT GRINDER
We reserve the right to make technical changes in the interests of progress and subject to changes in form and colour.
www.eisenblaetter.de
Tel.: +49 - 8171 - 93 84 - 0 Fax: +49 - 8171 - 93 84 - 55
§ 1 Sco pe, defence clause
(1) Our terms of sales shall be exclusively applicable; we do not
accept any contrary terms or terms from resellers, purchasers and other
buyers (“customers”) which differ from our terms of sale unless we have
expressly agreed to their validity in writing. Our terms of sale shall apply even
if we deliver goods to the customers without reservation despite being aware
of the fact that the customer has contrary terms or terms which are different
from our terms of sale.
(2) All agreements which are made between us, in other words
between Gerd Eisenblätter GmbH (hereinafter known as EISENBLÄTTER),
and the customer relating to the fulfilment of this contract shall be set out in
writing in this contract. In addition the statutory regulations shall apply unless
a legal agreement has been made by mutual consent to deviate from them.
(3
) Our terms of sale shall only apply to non-consumers in the sense
of § 310 Paragraph 1 of the Civil Code.
(4) These terms of sale shall also apply to all future transactions with the
customer if these tractions are related in type.
§ 2 Order acceptance, written form
(1) Orders must be issued to Eisenblätter in writing and shall not give
rise to a contract until they have been confirmed in writing by
EISENBLÄTTER.
(2) EISENBLÄTTER shall be entitled to continue to develop its
products. It reserves the right to make minor technical or other changes as
long as they are within a reasonable framework for the customer.
(3) The information supplied for the various products shall be for the
purpose of product description only. It shall not be possible to derive a
specific property or the suitability for the products for a specific purpose from
such information.
§ 3 Delivery
(1) Lead times shall only be binding if they have been agreed as such
in the order confirmation.
(2) If the delivery of the goods is delayed for reasons which are
beyond the control of EISENBLÄTTER, in particular as a result of forces
majeures, operational problems or labour disputes, the agreed lead time shall
be extended tacitly by the reasonable period required to rectify this cause.
(3) The ordered products shall be delivered by EISENBLÄTTER at a
charge using the means of transport selected by EISENBLÄTTER, for
example by parcel service, or on the basis of a special agreement.
(4) If the EISENBLÄTTER products are shipped to the customer, the
risk of accidental loss or random deterioration of the products shall be
transferred to the customer at the latest when the products leave
EISENBLÄTTER’s warehouse/plant. This shall apply regardless of whether
the products are shipped from the place of fulfilment or who is responsible for
the shipment costs.
§ 4 Terms of payment
(1) The quoted purchase price shall be binding for a period of 30
days from the date on which the quotation is submitted. Statutory valueadded tax is not included in our prices; this shall be charged at the statutory
rate on the date of the invoice and shown separately on the invoice.
(2) Setting off or retention against claims of all types shall not be
permitted unless these claims have been finalised by a court of law, are
undisputed or a decision is pending on them.
§ 5 Warranty
(1) Warranty rights assume that the customer has correctly fulfilled its
duties to inspect the goods and complain about them if they are defective
under § 377 of the Commercial Code.
(2) If the goods are defective at the time when the risk is transferred,
the customer shall be entitled to repeat fulfilment in the form of defect
rectification or the delivery of new, perfect goods at the discretion of
EISENBLÄTTER.
(3) If the attempt at repeat fulfilment fails, the customer shall be
entitled to demand cancellation or a reduction of the purchase price at its own
discretion.
(4) Recourse claims under §§ 478 and 479 of the Civil Code shall
only apply if the claim was justified by the consumer and shall only apply
within the statutory framework, but shall not apply to goodwill agreements
agreed with the seller. The customer must notify the seller as soon as
possible of any warranty claim made by a consumer.
(5) The statute of limitations for warranty claims for defects against
EISENBLÄTTER shall be 12 months starting from the date of delivery of the
goods. This shall not apply if the law set out in § 438 Paragraph 1 No. 2
(structures and goods for structures), § 479 Paragraph 1 (recourse claims)
and § 634 a Paragraph 1 No. 2 of the Civil Code (design defects) specifies
longer statute of limitations and in cases of death, physical injury or health
impairment in the event of a malicious or grossly negligent breach of duty on
the part of EISENBLÄTTER or its legal representative or agents and in the
event of maliciously neglecting to disclose a defect or if a guarantee is
accepted for a specific property of the product.
6) § 6 shall apply for compensation claims.
§ 6 Liability
(1) Claims for compensation and for the reimbursement of expenses
on the part of the customer (hereinafter known as compensation claims),
regardless of their legal basis, in particularly as a result of a breach of duties
from an obligation based on an illegal act, shall be excluded. This shall not
apply in the event that a guarantee has been given or a purchase risk exists.
This shall also not apply if binding liability applies, for example under the
Product Liability Law, in cases of malice or gross negligence, in cases of
death, physical injury or health impairment and in cases of breaches of major
contract duties. This shall not involve any change in the burden of proof to the
disadvantage of the customer.
(2) The compensation claim for the breach of major contract duties
shall be limited, however, to the foreseeable damage typical for this type of
contract unless gross culpability applies or in the event of liability for death,
physical injury or health impairment. This shall not involve any change in the
burden of proof to the disadvantage of the customer.
(3) If liability for compensation on our part is excluded or limited, this
shall also apply to the personal liability for compensation of our staff,
employees, colleagues, representatives and agents.
§ 7 Reservation of title, copyright
(1) For contracts with business people, EISENBLÄTTER shall
reserve title to all the supplied EISENBLÄTTER products until all claims
relating to the business relationship have been settled in full. In the case of
customers who are not business people, EISENBLÄTTER shall reserve title
to supplied EISENBLÄTTER products until the purchase price has been paid
in full.
(2) Resellers shall only be entitled to resell the products which are
subject to reservation of title under § 7 No. 1 within the framework of their
normal business activities. They shall not be entitled to dispose of these
products by any other method or by pledging them. The reseller hereby
assigns its claims accrued from the resale of the products together with
additional rights to EISENBLÄTTER in order to secure all the claims accrued
by EISENBLÄTTER under § 7 Paragraph 1. The reseller shall be entitled to
collect the assigned claims. If seizures are made against the products subject
to the reservation of title described in § 7 Paragraph 1 or if they are exposed
to other action by third parties, the customer must notify EISENBLÄTTER
without delay. If the value of the securities held by EISENBLÄTTER exceeds
the value of its total claims by more than 15%, EISENBLÄTTER shall release
the securities of its choice at the request of the customer. If insolvency
proceedings are opened against the assets of the reseller or if the reseller is
insolvent or indebted, its entitlement described in § 7 Paragraph 2 shall
automatically be voided.
(3) In the event of the customer acting against this contract, in
particular in the event of the customer being in default or a breach of a duty
set out in § 7 Paragraph 2, EISENBLÄTTER shall be entitled to withdraw
from the contract and demand the return of the goods.
(4) EISENBLÄTTER shall reserve the title and any copyright to
photographs, drawings, catalogues and other documents which are supplied
to the customer, including quotations and documents relating to price
calculations, etc. If these documents do not belong to documentation,
descriptions and instructions for data processing programs for which separate
contractual provisions apply, they must not be copied or disclosed to third
parties without the written consent of EISENBLÄTTER.
(5) In addition the documents supplied by EISENBLÄTTER are
protected by copyright. The grant of any utility rights shall require a special
agreement. Under no circumstances shall it be permitted to make copies or to
permit a third party to do so. This shall not include end customers who have
been expressly permitted to do this by EISENBLÄTTER.
§ 8 Concluding provisions
(1) Any assignment of the rights or transfer of the duties set out in
this contract shall require the prior written consent of EISENBLÄTTER.
(2) If a provision in these terms of sale and delivery should be or
become invalid, the other provisions shall not be affected.
§ 9 Place of jurisdiction and applicable law
(1) If the customer is a businessman, legal entity under public law or
a special fund under public law, our registered business address shall be the
place of jurisdiction. However, we shall also be entitled to sue the customer at
his home address. The same shall apply if the customer does not have a
general place of jurisdiction in the Federal Republic of Germany or his place
of abode or normal place of residence are not known at the time when the
lawsuit is lodged.
(2) The law of the Federal Republic of Germany shall apply. The
validity of the UN Convention on Contracts for the International Sale of Goods
shall be excluded.
(3) Unless specified to the contrary in the order confirmation, our
registered business address shall be the place of fulfilment and payment.
Date of issue: November 2008
Loading...