EIPL rm85 Owner's Manual
Drawing : - TPC408
Issue : - 3
Date : - 08/08/14
RM85
INDUSTRIAL DEHUMIDIFIER
OWNER’S MANUAL
www.eipl.co.uk
Page 1 of 12
Drawing : - TPC408
Issue : - 3
Date : - 08/08/14
RM85
PACKAGE CONTENTS
Item Description Quantity
10560RG-US Dehumidifier 1
3086144 Quick release hose coupling 1
3944110 PVC Tube – 3/8” I/D 7.8M
TPC408 Manual 1
Page 2 of 12
Drawing : - TPC408
Issue : - 3
Date : - 08/08/14
INTRODUCTION
Designed for a wide range of applications, the RM85 is a rugged, industrial
unit, which utilizes an energy-efficient compressor and a compact portable
design to provide easy efficient drying.
The RM85 has a number of special features:
•
High efficiency rotary compressor
•
EIPL’s “Hot Gas” defrost system
•
Hours run meter
•
Integral pump out system
•
Provision for permanent drainage
•
Extra long power cord
•
Robust rotational moulded polyethylene housing
•
Separate outlets allowing dry air to be ducted
The fan draws the moist air through the cold evaporator coil, which cools the
air below its dew point. Moisture forms on the evaporator coil and is collected
in the condensate tray, which is equipped with a permanent drain. The cooled
air then passes through the hot condenser coil where it is reheated using the
same energy removed during the cooling phase, plus the additional heat
generated by the compressor. The air is, therefore, discharged from the
dehumidifier at a slightly higher temperature with a lower absolute humidity
than that which entered. Continuous circulation of air through the
dehumidifier gradually reduces the relative humidity within the area.
The RM85 dehumidifier is a rugged, reliable drying unit designed to operate
effectively over a broad range of temperature and humidity conditions. An
active hot gas defrost system, controlled by an electronic timer, guarantees
positive de-icing, thereby optimizing operation at low temperatures.
The unit incorporates a rotational moulded polyethylene shell resilient to
damage caused by rough handling.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
If the SUPPLY CORD is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified person in order to avoid hazard.
Page 3 of 12
Drawing : - TPC408
Issue : - 3
Date : - 08/08/14
SPECIFICATIONS
P
OWER SUPPLY
O
PERATING RANGE
R
"This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. The
refrigeration system is hermetically sealed.
The Global Warming Potential (GWP) of refrigerants used in products manufactured by Ebac
For type and weight of refrigerant contained in this unit, please refer to the product data label"
M
ODEL
: 10560rg-us
H
EIGHT
: 37.2” (945mm)
W
IDTH
: 21.5” (545mm)
D
EPTH
: 19.4” (492mm)
W
EIGHT
: 99 lbs (45 Kg)
A
IRFLOW
: 230 CFM (390 M3/hr)
: 110V/ 60Hz/ 1 ph
F
INISH
Rotational Moulded
:
polyethylene
: 33°F – 95°F
EFRIGERANT
: R-407c (17.6 oz)
Industrial Products Ltd is as follows
R134a – 1300
R407c – 1610
Page 4 of 12
Loading...