EIPL AM2000 User Manual

UK Head Office

American Sales Office

German Sales Office

Ebac Industrial Products Ltd

Tel: [phone]

Fax: [phone]

AM2000

USER MANUAL

Drawing No.

:- TPC

403

For service questions, contact
Ebac at 1-757-873-6800.
For sales inquiries, contact
Sylvane at 1-800-934-9194.

Ebac Industrial Products Ltd

St Helens Trading Estate

Bishop Auckland

County Durham

DL14 9AD

Tel: [phone]

Fax: [phone]

www.eipl.co.uk

[e-mail]

Ebac Industrial Products Inc

700 Thimble Shoals Blvd.
Suite 109, Newport News

Virginia, 23606-2575

Tel: [phone]

Fax: [phone]

[e-mail]

USA

www.ebacusa.com

Miraustra 64 – 66

13509

Berlin

Germany

www.eip-ltd.de

[e-mail]

AIR

MOVER

Issue :- 1
Date :- 01/10/13

IF YOUR

AIRMOVER

FAILS TO

Check that the plug is fully pushed

Check with some other electrical

device that the wall socket is “live”. If

it is not, contact a qualified

circuit breaker on the

Should none of the above remedies

work, then disconnect from the mains.

. DO NOT attempt

to repair the unit or unscrew the outer

IPL

over from its packing carton,

isually inspect for any signs of transit

damage. If there are any signs of

damage, do not operate your unit. Call

your supplier immediately for advice. Do

not discard the packing for it will be

it in the

A cord wrapping facility has been

moulded into the plastic fan housing.

The power cord should be wrapped

around this facility during transit. Do not

over during

e

ELECTRICAL CONNECTION

If the appliance is fitted with a plug for

which your socket is unsuitable, then it

and an appropriate plug

Air Movers are high performance,

high efficiency fan systems designed to

optimize air movement and minimize

inlet,

centrifugal type fan design to provide the

high static pressure and airflow required

to dry water damaged facilities and

Air Mover series

was designed to provide you the best

•

•

• Aerodynamic, Rotationally Moulded

•

•

• 4 operating Positions (0º, 12º, 45º, &

• Stack ability in the Vertical Plane

•

OPERATING PROCEDURES

grounded

turn the power

If you have no

loud or abnormal

Air Mover is designed to

operate in 4 positions to allow drying of

mes with internal

circuit protection for your safety. When

working around a wet environment, we

also recommend always plugging the

unit into a ground fault interrupter to

For the drying of water damaged

dehumidifier along with your air mover to

provide you with more efficient drying.

Your air mover is designed to induce

evaporation or water contained within

flooded surfaces or materials. Yet,

removing the

om the air, drying will not

occur. It is recommended that the

dehumidifier outlet is close to the air

mover intake. This allows for dry air to

personnel or other persons

having technical competence servicing refrigeration equipment following the

Ebac service manuals and spares lists are available upon request by contacting

• This machine has been manufactured in the United Kingdom.

TECHNICAL SPECIFICATIONS

IMPORTANT

As the colours of the wires in the mains

not correspond

with the coloured markings identifying the

terminals in your own plug, proceed as

The wire which is coloured Green and

Yellow must be connected to the terminal

in the plug which is marked with the letter

coloured

Green and Yellow. The wire which is

coloured Blue must be connected to the

terminal in the plug which is marked with

the letter N or coloured Black. The wire

which is coloured Brown must be

connected to the terminal which is marked

You must dispose of the non rewireable

plug once it has been removed from the

flexible cord. It is dangerous to attempt to

insert the plug into any electrical socket

elsewhere in the house. If the flexible cord

be replaced by

an identical cord.

WARNING

– THIS APPLIANCE MUST BE EARTHED

Connect the power cord into a

UNPACKING

Remove the top insert and your E
Air M
v

useful for transporting your un
future.

TRANSPORTATION

electrical outlet and
switch to the ON position.
power or hear any
noises and consult your supplier.

Your EIPL

floors, walls and ceilings.

Your EIPL Air Mover co

drop or abuse your Air M
transit for risk of damage to both th
motor and housing.

assure the best protection.

facilities, we recommend using an EIPL

INTRODUCTION

EIPL

operating costs for drying applications.

without a mechanism for
moisture fr

Each model incorporates a double

be distributed by the air mover.

equipment. The EIPL

performance and serviceability.

25 ft. Power Cord with cord grip
Internal thermal Circuit Breaker

Polythene Housing.
High Efficient 1/2 HP Motor
Three Speed Fan Design

1.
into the socket and is switched on.

2.

electrician.

3. Check the
control panel and reset as required.

OPERATE

90º)

during both Storage and Operation.

Contact your supplier

Moulded Cord wrap Facility

casing.

lead of this appliance may

should be cut off
fitted.

follows:

This appliance complies with the
suppression requirements of the EEC
direction 82/199/EEC as embodied in

E or by the Earth Symbol or
BS800:1988.
IMPORTANT:- The wires in this mains
lead are coloured in accordance with the
following code:-

Green Earth

with the letter L or coloured Red.

White Neutral
Black Live

becomes damaged it must

AM2000 115V/60Hz/1

Phase

Height 21”

Width 20”

Depth 19”

Weight 34lbs

Horsepower ½

Max running current 5A

Fan Speeds 3

• This machine should be serviced by qualified Ebac

instructions in the Ebac service manual.

•
your local Ebac distributor.

• Never operate the unit in a bathroom or swimming pool area

• Do not use the machine if the power cord or case are damaged.

• Do not poke objects into and of the grilles on the machine.

• Do not cover or obstruct the air inlet or outlet.

• This machine complies with the electromagnetic compatibility 1992 regulations.