EINHELL 1500 SA Operating Instructions Manual

Page 1
BT-VC 1500 SA; EX; UK
Wet/Dry Vacuum Cleaner (elect)
Artikel-Nr.: 2342157
Ident-Nr.: 11010
Page 2
Komponenten / Ersatzteile
Position Artikel-Nr. Beschreibung 1 234215701001 Handle
2 234215701002 Switch
3 234215701003 Socket (UK)
4 234215701004 Switch
12 234215701012 Castor foot (4 pcs.)
13 234215701013 Metal wands (pair)
16 234215701016 Power tool adaptor
Page 3
Art.-Nr.: 23.421.57 I.-Nr.: 11010
Original operating instructions
Wet and Dry Vacuum Cleaner
BT-VC 1500 SA
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 1
Page 4
2
1
2 3
14
9
5
17
17
6
8
13
21
20
7
10
18
1
17
25
22
9
11
12
19
16
4
15
23
24
14
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 2
Page 5
3
4
6
5
12
12
10
18
5
8
7
1.
2.
24
19
2
25
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 3
Page 6
4
GB
Important!
When using equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, give them these operating instructions as well. We accept no liability for damage or accidents which arise due to non-observance of these instructions and the safety information.
1. Safety information
Important: Read the operating instructions before
assembling and using the appliance for the first time.
Check that the mains voltage is the same as the
mains voltage specified on the rating plate.
Pull out the power plug in the following
circumstances: Whenever the appliance is not in use, before opening the appliance and before all cleaning and maintenance work.
Never clean the appliance with solvents.Never pull the plug out of the socket by pulling the
cable.
Never leave the appliance unattended when
operational.
Keep away from children.Take care to ensure that the power cable does
not get damaged by being run over, crushed, pulled or suchlike.
Do not use the machine if the power cable is in a
less than perfect condition.
If the power cable has to be replaced, the
replacement must comply with the design specifications of the manufacturer. Power cable:
H 05 VV - F 3 x 1.5 mm
2
Never vacuum the following: Burning matches,
smoldering ash and cigarette butts, combustible, caustic, inflammable or explosive substances, vapor or liquids.
This appliance is not suitable for vacuuming dust
which can be harmful to health.
Store the appliance in a dry indoor location.Never use the appliance if it is damaged.Only allow the appliance to be serviced by an
authorized after sales service outlet.
Only use the appliance to carry out work for which
has been designed.
Take extra care when cleaning steps.Use only genuine accessories and spare parts.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. Layout and items supplied (Fig. 1-4)
1. Handle
2. Hook for cable store
3. Power cable
4. Automatic socket-outlet for electric tools
5. Head
6. Handle
7. Accessory holder
8. Suction hose connection
9. Flexible suction hose
10. Tank
11. Water drain screw
12. Castors
13. Air regulator
14. Dual purpose nozzle
15. ON/OFF switch
16. Automatic switch
17. 2-piece suction tube
18. Locking hook
19. Blow connector
20. Filter cage
21. Safety float valve
22. Electric tool adapter
23. Crevice nozzle
24. Pleated filter with cover
25. Foam filter
3. Intended use
The wet and dry vacuum cleaner is designed for wet and dry vacuuming using the appropriate filter. The appliance is not suitable for the vacuuming of combustible, explosive or harmful substances.
The machine is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 4
Page 7
5
GB
4. Technical data
Mains voltage: 230 V ~ 50 Hz
Power input: 1500 watts
Max. power consumption of the automatic socket-
outlet: 1400 watts
Max. total power consumption: 2900 watts
Container volume: 30 l
Weight: 10 kg
5. Before starting
Important!
Before you connect the appliance to the mains
supply make sure that the data on the rating plate are identical to the mains data.
The appliance may only be connected to a shock-
proof socket.
5.1 Assembling the appliance
5.1 Appliance assembly Fitting the castors (Fig. 6/12)
Fit the castors (12) into the appropriate mountings on the underside of the tank (10). Push the castors (12) firmly into the mounting until they engage with a clicking noise (Fig. 6).
Fitting the appliance head (Fig. 5)
The appliance head (5) is fastened to the container (10) by the locking hook (18). To remove the appliance head (5), open the locking hook (18) and remove the appliance head (5). When fitting the appliance head (5), make sure that the locking hook (18) locks into place correctly.
5.2 Fitting the filter
Important!
Never use the wet and dry vacuum cleaner without a filter. Check that the filter is securely fitted at all times.
Fitting the foam filter (Fig. 7/25)
For wet vacuuming, slip the supplied foam filter (25) over the filter basket (Fig. 2/20). The pleated filter (24) already fitted upon delivery is not suitable for wet vacuuming.
Fitting the pleated filter (Fig. 8/24)
For dry-vacuuming, slip the pleated filter (Fig. 3/24) over the filter basket (Fig. 2/20). The pleated filter (24) is suitable for dry-vacuuming only.
5.3 Fitting the suction hose (Fig. 1/9)
Connect the suction hose (9) to the corresponding connector on the wet and dry vacuum cleaner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose connector (8).
Blowing
Connect the suction hose (9) to the blow connector (19).
To extend the suction hose (9) you can attach one or more of the elements which make up the 2-part suction tube (17) to the suction hose (9).
Air regulator (Fig. 1/13)
The air regulator (13) can be fitted between the suction hose (9) and the suction tube (17). The suction power of the nozzle can be infinitely adjusted using the air regulator (13).
5.4 Suction nozzles
Combination nozzle (Fig. 1/14)
For dry vacuuming surfaces use the dual-purpose nozzle (14).
Crevice nozzle (Fig. 1/23)
The crevice nozzle (23) is designed for vacuuming solids and liquids in corners, edges and other areas that are difficult to access.
6. Operation
6.1.1 ON/OFF switch (Fig. 2/15)
Switch position 0: Off Switch position I: On
6.1.2 Automatic switch (Fig. 2/16)
Switch position _ : Normal mode Switch position = : Automatic mode
6.2. Dry vacuuming
Use the pleated filter (24) for dry vacuuming (see point 5.2). Always ensure that the filters are perfectly secure.
6.3 Wet vacuuming
For wet-vacuuming, use the foam filter (25) (see point
5.2). Check that the filter is securely fitted at all times.
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 5
Page 8
6
GB
Water drain screw (Fig. 1/11)
To make the tank (10) easier to empty after wet vacuuming, it is fitted with a water drain screw (11). Open the water drain screw (11) by turning it anti­clockwise and drain the liquid.
Important.
When wet vacuuming, the floating safety switch (21) closes when the maximum tank level is reached. In doing so, the suction noise of the equipment will change and become louder. Then switch off the equipment and empty the tank.
Important!
The wet and dry vacuum cleaner is not suitable for the vacuuming of combustible liquids. For wet vacuuming, use only the supplied foam filter.
6.4 Automatic mode
Connect the power cable on your electric tool to the automatic socket-outlet (4) and connect the suction hose (9) to the extractor connector on your electric tool. Check that the connections are secure and air­tight.
You can use the supplied electric tool adaptor (22) to connect the suction hose (9) to the electric tool. To do so, fit it between the suction hose and the extractor port on the electric tool.
Set the switch (16) on the wet and dry vacuum cleaner to position =, automatic mode. The moment you switch on the electric tool, the wet and dry vacuum cleaner switches on as well. When you switch off the electric tool, the wet and dry vacuum cleaner switches off as well after a pre-set delay.
6.5 Blowing
Connect the suction hose (9) to the blow connector (19) on the wet and dry vacuum cleaner.
7. Cleaning, maintenance and ordering of spare parts
Important!
Always pull out the mains power plug before starting any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
We recommend that you clean the appliance
immediately after you use it.
7.2 Cleaning the appliance head (5)
Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the appliance.
7.3 Cleaning the container (10)
The container can be cleaned with a damp cloth and some soft soap or under running water, depending on the amount of dirt.
7.4 Cleaning the filters Cleaning the pleated filter (24)
Clean the pleated filter (24) regularly by carefully patting it and cleaning it with a fine brush or hand brush.
Cleaning the foam filter (25)
Clean the foam filter (25) with a little soft soap under running water and allow it to air-dry.
7.5 Maintenance
At regular intervals and before each use, check that the filters in the wet and dry vacuum cleaner are securely fitted.
7.6 Ordering replacement parts
Please quote the following data when ordering replacement parts:
Type of machine: BT-VC 1500 SAArticle number of the machine: 23.421.57Identification number of the machine: 11010Replacement part number of the part required
For our latest prices and information please go to www.einhell-uk.co.uk
8. Disposal and recycling
The unit is supplied in packaging to prevent its being damaged in transit. This packaging is raw material and can therefore be reused or can be returned to the raw material system. The unit and its accessories are made of various types of material, such as metal and plastic. Defective components must be disposed of as special waste. Ask your dealer or your local council.
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 6
Page 9
7
k erklärt folgende Konformität gemäß EU-Richtlinie und
Normen für Artikel
t explains the following conformity according to EU
directives and norms for the following product
p déclare la conformité suivante selon la directive CE et les
normes concernant l’article
C dichiara la seguente conformità secondo la direttiva UE e
le norme per l’articolo
N verklaart de volgende overeenstemming conform EU
richtlijn en normen voor het product
m declara la siguiente conformidad a tenor de la directiva y
normas de la UE para el artículo
O declara a seguinte conformidade, de acordo com a
directiva CE e normas para o artigo
l attesterer følgende overensstemmelse i medfør af
EU-direktiv samt standarder for artikel
U förklarar följande överensstämmelse enl. EU-direktiv och
standarder för artikeln
q vakuuttaa, että tuote täyttää EU-direktiivin ja standardien
vaatimukset
. tõendab toote vastavust EL direktiivile ja standarditele j vydává následující prohlášení o shodě podle směrnice
EU a norem pro výrobek
X potrjuje sledečo skladnost s smernico EU in standardi za
izdelek
W vydáva nasledujúce prehlásenie o zhode podľa smernice
EÚ a noriem pre výrobok
A a cikkekhez az EU-irányvonal és Normák szerint a
következő konformitást jelenti ki
P deklaruje zgodność wymienionego poniżej artykułu z
następującymi normami na podstawie dyrektywy WE.
e декларира съответното съответствие съгласно
Директива на ЕС и норми за артикул
H paskaidro šādu atbilstību ES direktīvai un standartiem G apibūdina šį atitikimą EU reikalavimams ir prekės
normoms
Q declară următoarea conformitate conform directivei UE
şi normelor pentru articolul
z δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την
Οδηγία ΕΚ και τα πρότυπα για το προϊόν
B potvrđuje sljedeću usklađenost prema smjernicama EU
i normama za artikl
f potvrđuje sljedeću usklađenost prema smjernicama EU
i normama za artikl
4 potvrđuje sledeću usklađenost prema smernicama EZ i
normama za artikal
T следующим удостоверяется, что следующие
продукты соответствуют директивам и нормам ЕС
1 проголошує про зазначену нижче відповідність
виробу директивам та стандартам ЄС на виріб
5 ја изјавува следната сообрзност согласно
ЕУ-директивата и нормите за артикли
Z Ürünü ile ilgili AB direktifleri ve normları gereğince
aşağıda açıklanan uygunluğu belirtir
L erklærer følgende samsvar i henhold til EU-direktivet
og standarder for artikkel
E Lýsir uppfyllingu EU-reglna og annarra staðla vöru
Konformitätserklärung / Declaration of Conformity
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Wet and Dry Vacuum Cleaner BT-VC 1500 SA (Einhell)
Standard references: EN 60335-1; EN 60335-2-2; EN 62233; EN 55014-1;
EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 10.09.2010
First CE: 10 Archive-File/Record: 2342150-28-4141750-07 Art.-No.: 23.421.57 I.-No.: 11010 Documents registrar: Roider Siegfried Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
Weichselgartner/General-Manager Wang/Product-Management
x
x
87/404/EC_2009/105/EC 2005/32/EC_2009/125/EC 2006/95/EC 2006/28/EC 2004/108/EC 2004/22/EC 1999/5/EC 97/23/EC 90/396/EC_2009/142/EC 89/686/EC_96/58/EC
2006/42/EC
2004/26/EC
Emission No.:
2000/14/EC_2005/88/EC
Annex IV
Notified Body: Notified Body No.: Reg. No.:
Annex V Annex VI
Noise: measured LWA= dB (A); guaranteed LWA= dB (A) P = KW; L/Ø = cm Notified Body:
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 7
Page 10
8
t For EU countries only
Never place any electric tools in your household refuse.
To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the demand to return electrical devices: As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the device is properly recycled if ownership is relinquished. This can also be done by handing over the used device to a returns center, which will dispose of it in accordance with national commercial and industrial waste management legislation. This does not apply to the accessories and auxiliary equipment without any electrical components which are included with the used device.
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 8
Page 11
9
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH.
Technical changes subject to change
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 9
Page 12
10
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 10
Page 13
11
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 11
Page 14
t
GUARANTEE CERTIFICATE
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which guarantee claims can be made:
1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.
We do not charge you for this guarantee.
2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the
rectification of these defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by the device being dropped) and normal wear resulting from proper operation of the device. This applies in particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
3. The guarantee is valid for a period of 2 years starting from the purchase date of the device. Guarantee
claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies when an on-site service is used.
4. In order to assert your guarantee claim, please send your defective device postage-free to the address
shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.
Einhell UK Ltd
Morpeth Wharf
Twelve Quays
Birkenhead, Wirral
CH41 1LF
Tel. 0151 6491500, Fax 0151 6491501
EH 09/2010 (01)
Anleitung_BT_VC_1500_SA_SPK7:_ 05.10.2010 7:14 Uhr Seite 12
Loading...