EIM HQ-008 to 300 Series Installation and Operation manual Manuals & Guides

HQ Series ¼ Turn Actuator

HQ-015 thru HQ-300

IInnssttaallllaattiioonn && MMaaiinntteennaannccee MMaannuuaall

HQ Series I&M Manual HQ-400-1005 1

Table of Contents:

General 1.0

Actuator Mounting 2.0

External Construction 3.0

Wiring Diagrams 4.0

Power Requirements 5.0

Duty Cycle

Manual Override

6.0

7.0

Mechanical Travel Stops 8.0

Electrical Connection 9.0

Limit Switch Setting Instructions 10.0

Torque Switch Adjustment 11.0

Reverse Acting (Counter Clockwise to close) 12.0

Lubrication 13.0

MDPI (Mechanical Dial Position Indicator) 14.0

Maintenance 15.0

Storage 16.0

Mounting Base Details 18.0

Drive Bushing Details

19.0

Trouble Shooting 20.0

Standard Specifications

EIM Office Locations

HQ Series I&M Manual HQ-400-1005 2

21.0

22.0

1.0 General

HQ series electric actuators are design to provide reliable and efficient operation of 90 degree quarter turn
valves, dampers, etc

Pre-Installation Inspection

.

Warning: Use caution when working in, with, or around valves and
actuators. High pressures, forces, voltages and flammable media can be
present

Warning: Failure to follow instructions for proper electrical wiring, storage,
set-up and maintenance may cause serious injury, damage equipment, or
void warranty.

Verify the actuator nameplate to insure correct model number, torque, operating speed, voltage
and enclosure type before installation or use.

It is important to verify that the output torque of the actuator is appropriate for the torque
requirements of the valve and that the actuator duty cycle is appropriate of the intended application

2.0 Actuator Mounting

Do not lift the actuator by the handwheel

The actuator may be mounted in any position

The HQ- Series actuators are supplied with a female drive output. ISO5211. Bolt patterns are provided for
actuator mounting. The actuator drive bush is removable for ease of machining.

It is mandatory that the actuator be firmly secured to a sturdy mounting bracket or directly mounted to the
valve’s ISO mounting pad. High tensile bolts or studs with spring locking washers must be used.

The valve output shaft must be in line with the actuator output drive to avoid side-loading the shaft.

To prevent backlash, no flexibility in the mounting bracket or mounting should be allowed.

HQ Series I&M Manual HQ-400-1005 3

3.0 External Construction
HQ-008 ~ HQ-120

HQ-200 ~ HQ-300

HQ Series I&M Manual HQ-400-1005 4

4.0 Wiring Diagrams

HQ Series I&M Manual HQ-400-1005 5

5.0 Power Requirements

Consult the nameplate of the actuator for duty cycle and current draw information

6.0 Duty Cycle

Duty cycle rated IEC34 – S2 (30%)
Exceeding the actuator’s rated duty cycle may cause thermal overload.

7.0 Handwheel Declutch

HQ actuators are provided with a declutchable manual override system.
 To manually operate the actuator, pull the manual declutch lever towards the handwheel until it remains in

position.

 Turn the handwheel until the valve reaches the required position
 Turn clockwise to close and counter -clockwise to open

☞The manual declutch lever has motor preference, meaning that when the motor is energized, the lever
will automatically shift to auto position.

7.0 Mechanical Travel Stop Adjustment

Built-in mechanical stops are provided to prevent handwheel operation beyond total valve travel

 Loosen both locknuts and back out the stopbolts
 Run actuator electrically to fully closed position
 Screw close stopbolt in until it it seats, then back

Off ½ turn, Install washer and tighten locknut

 Run actuator electrically to fully open position
 Screw open stopbolt in until it it seats, then back

Off ½ turn, Install washer and tighten locknut

☞Do not set the Actuator position limit switches to drive into the mechanical stops. Damage can occur
of electric unit is allowed to repeatedly stall into the end stops.

HQ Series I&M Manual HQ-400-1005 6

9.0 Electrical Connection

 Move valve to mid-position by handwheel. This will allow sufficient time to stop actuator in case of

improper hook-up or reversed power phases

 Identify means of removing power during hookup
 Be sure no erroneous remote control signals can be received causing actuator to energize
 Electrically operate the valve in the open direction. If the valve closes, actuator must be stopped and

the power leads reversed to correct voltage phasing or improper field wiring.

 Set all field conduit entries in accordance with National Electric Code Requirements

☞Improper power voltage phasing eliminates protection of both the position limit switch and torque
switches, risking valve damage.

10.0 Limit Switch Setting Instructions

HQ Series I&M Manual HQ-400-1005 7

10.0 Limit Switch Setting Instructions (cont)

 Operate the actuator manually to closed position
 Using a hex wrench, loosen the cam adjustment screw in the CLOSE limit switch cam
 Rotate the CLS cam towards CW limit switch lever until the switch ‘clicks’
 Tighten set screw with hex wrench
 Operated the actuator manually to open position
 Using a hex wrench, loosen the cam adjustment screw in the OPEN limit switch cam
 Rotate the OLS can towards CCW limit switch lever until the switch ‘clicks’
 Tighten set screw with hex wrench

11.0 Torque Switch Adjustment

The torque switches are adjusted at factory to protect actuator and valve against over torque.
Should adjustment be necessary, please contact the factory, or your local EIM distributor for assi stance.

12.0 Reverse Acting (Counter Clockwise to Close)

Standard factory actuators are normally set to clockwise rotation to close. However the rotation can be
reverse to counter-clockwise to close by simply reconfiguring the wiring as follows:

 Exchange 9 and 10 in main actuator terminal block
 Exchange 11 and 12 in main actuator terminal block

If a PCU card is installed:

 Exchange Potentiometer input wires P1(Orange wire) and P3 (Grey wire) on PCU
 Change the direction of the indicator (HQ-200 and 300 only)
 Re Calibrate by using Auto Calibrate feature

14.0 Lubrication

The HQ series actuators are totally enclosed units with a permanently lubricated gear trains (Moly EP
Grease). Once installed lubrication should not be required. However, periodic preventative maintenance
will extend the operating life of the actuator.

HQ Series I&M Manual HQ-400-1005 8

15.0 MDPI Settings

 Manually rotate actuator to fully closed position
 Remove actuator cover
 Loosen indicator screw
 Adjust indicator to correct orientation
 Tighten indicator screw
 Replace cover
 Check indicator alignment

16.0 Maintenance

At least once a year a check should be make of your EIM HQ Series Actuator

 Disconnect all power to actuator.
 Open Electrical Enclosure. Inspect and tighten all electrical connections
 Visually inspect for any electrical or mechanical damage. Replace worn or damaged components.

 Check lubrication consistency and levels. Fill or replace if required.

17.0 Storage

Actuators must be stored in a clean, cool and dry area. The unit shall be stored with the cover installed
and the conduit openings sealed. Storage must be off the floor, covered with a sealed dust protector.

HQ Series I&M Manual HQ-400-1005 9

21.0 Trouble Shooting

The following instructions are offered for the most common difficulties encounter during installation and
start-up

Motor will not Run Open in control circuit Refer to appropriate wiring diagram
and check for continuity
Insulation resistance breakdown in motor Perform Megger Test
No power available to actuator Tripped circuit breaker Reset circuit breaker
Handwheel hard to turn Valve stem improperly lubricated Lubricate with grease
Actuator lubrication has broken down Clean out old grease and replace
with recommended lubricant
Valve packing gland too tight Loosen packing gland nuts as
necessary
Jammed valve Refer to valve maintenance
Valve only opens or closes Torque switch setting too low Check setting and reset if necessary
partially with motor Limit switch improperly set Check setting and reset if necessary
Torque switch is properly set, but Damaged or bent valve stem Refer to valve maintenance
actuator torques out in mid-travel, Valve packing too tight Refer to valve maintenance
open or closed direction Jammed valve (obstruction in line) Refer to valve maintenance
Handwheel will not operate valve Stripped gearing Replace as necessary
Clutch shifter position or malfunction Move shifter, or replace as
necessary
Broken handwheel shaft Replace as necessary
Broken valve stem Repair or replace as necessary
Motor runs but will not operate Stripped gearing Replace as necessary
valve Clutch shifter position or malfunction Move shifter, or replace as
necessary
Broken handwheel shaft Replace as necessary

.

SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

HQ Series I&M Manual HQ-400-1005 10

HQ Standard Features

Enclosure Rated Weatherproof IP67, NEMA 4 & 6
Enclosure High grade aluminum alloy, corrosion coated
Power Supply 110/220VAC 1 PH 50/60Hz, 440VAC 3PH 50/60Hz
Duty Cycle EC 34 S2 (25~30%)
Motor Squirrel caged induction motor
Limit Switches 2 x open/close SPDT, 250VAC 10A rating
Auxiliary Limit Switches 2 x open/close SPDT, 250VAC 10A rating (except HQ008)
Torque Switches Open/close SPDT, 250VAC 10A Rating (except HQ008)
Stall Protection Built –in thermal protection
Travel Angle 90 degree +/- 10%
Indicator Continuous position indicator
Manual Override Declutchable manual override
Self Locking By means of worm gear
Mechanical Travel Stops 2 x external adjustable mechanical travel stops
Space Heater 7~10W ceramic housed
Conduit Entries 2 x PF3/4”
Lubrication Grease moly EP
Ambient Temperature -20 deg C ~ + 70 dec C (except on CPT & PCU board )
External Coating Dry powder polyester, Munsell No. 5R 3.5/12

HQ Series I&M Manual HQ-400-1005 11

Head Office and Factory

EIM Controls, Inc.
13840 Pike Road
Missouri City, Texas 77489 USA
[phone] toll-free, US Only
[phone] phone
[phone] fax

[e-mail]

EIM NorthEastern Regional Office

[e-mail]

EIM SouthWestern Regional Office

[e-mail]

EIM SouthEastern Regional Office

[e-mail]

EIM MidWestern Regional Office

[e-mail]

EIM Western Regional Office

[e-mail]

Eastern Hemisphere Sales

EIM Controls UK Ltd.
6-7 Galaxy House
New Greenham Park,
Newbury, Berkshire
RG19 6HW, England
[phone] phone
[phone] fax

[e-mail]

EIM Controls China

[e-mail]

EIM Controls Japan

[e-mail]

EIM Controls Italy

[e-mail]

EIM Controls Benelux

[e-mail]

HQ Series I&M Manual HQ-400-1005 12