Eiki PjNET-15 Owner's Manual
Pj-to NetDirector
Model No. PjNET-15
POWER
OWNER’S MANUAL
INSTALLATION and OPERATION of the Pj-to
NetDirector
This Pj-to NetDirector is an optional product to control
and set up a projector via a network. Attach this product to the projector and connect a network cable. By
accessing the connected projector using the web
browser on your computer, the projector can be controlled and set up remotely.
This product is only used for EIKI projectors that have a
terminal for the Pj-to NetDirector.
This manual explains the installation of the Pj-to
NetDirector and its operation.
Preparation
Installation
Basic Setting and Operation
Controlling the Projector
Controlling the Multi-Projectors
Use of Serial Port
Appendix
2
Preparation
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment causes harmful
interference to radio or television reception which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15
of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or modifications should be made, you could be
required to stop operation of the equipment.
Model Numbers : PjNET-15
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)
Trademark
Pj-to NetDirector is a trademark of EIKI International, Inc. Ethernet is a registered
trademark of Xerox Corporation. Microsoft, Windows, Windows NT are registered
trademarks of Microsoft Corporation. Macintosh, Mac OS are registered trademarks
of Apple Computer Inc. Internet Explorer is a registered trademark of Microsoft
Corporation. Netscape Navigator and Netscape Communicator are trademarks or registered trademarks of Netscape Communications Corporation. JavaScript is a registered trademark of Sun Microsystems, Inc.
Other product or brand names in this manual are registered trademarks or trademarks of their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
EIKI PjNET-15
3
Network Unit
OWNER’S MANUAL
Preparation
ENGLISH
Expression/Abbreviation
The following abbreviations may appear in this manual:
● Windows 95, Windows 98, Windows 2000,
Windows Me, Windows XP, Windows NT4.0 ➜ Windows
● Macintosh, Power Macintosh ➜ Macintosh
● Mac OS 8 or later ➜ Mac OS
In some cases, the “Pj-to NetDirector” is explained as “this product” or “Network
Unit” in this manual. The word “projector” found in this manual means “projector
provided with Pj-to NetDirector” unless otherwise noted.
Use of this manual
This manual does not provide the description of basic operation and functions for
computer, web browser, projector and network. For instructions about each piece of
equipment or application software, please refer to the respective booklet.
CAUTION ON USE IN NETWORK
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network,
you must perform the safety inspections periodically. In this case you must pay
attention to the change of environment in which you installed the projector. It may
cause fire or an accident depending on the change of environment.
CAUTION
EIKI International, Inc. assumes no responsibility for the loss or damage of data or
damage of the computer caused by use of this product.
4
Contents
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Expression/Abbreviation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Flow of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Name and function of each part . . . . . . . . . . . . . . . . . . . . . . . . . .11
[1] Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
[2] Connection of LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
[3] Confirmation of network menu activity . . . . . . . . . . . . . . . . . .14
[4] Network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Configure the network with the projector . . . . . . . . . . . . . . .16
Configure the network with the computer . . . . . . . . . . . . . . .18
Configure the network of computer . . . . . . . . . . . . . . . . . . . . . . .20
Windows 98/95/Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Windows 2000/NT4.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Notice about system construction . . . . . . . . . . . . . . . . . . . . .24
Basic Setting and Operation . . . . . . . . . . . . . . . . . .25
Login or logout the setting page of the projector . . . . . . . . . . . . .26
1 Enter the IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
2 Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3 Display of main setting page . . . . . . . . . . . . . . . . . . . . . . . .27
4 Logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
1 Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
2 Date/Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3 Password Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4 Temperature unit setting . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
1 Configure the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2 Name the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
E-mail Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Examples: Type and contents of alert mail . . . . . . . . . . . . . . .33
Controlling the Projector . . . . . . . . . . . . . . . . . . . . .35
Power on/off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Check the status of projector . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Control the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
PC Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
5
Network Unit
OWNER’S MANUAL
Contents
ENGLISH
SYSTEM Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
How to set the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Cancel the timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Save Actual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Control the projector's menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Controlling the Multi-Projectors . . . . . . . . . . . . . . .51
Multi-Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Register IP address and projector name . . . . . . . . . . . . . . . .52
Exclude/Add the projectors from/into the multi-control . . . . .53
Add all of listed projectors into multi-control . . . . . . . . . . . . .53
Delete from the multi-control list . . . . . . . . . . . . . . . . . . . . . .53
Load and apply the setting value . . . . . . . . . . . . . . . . . . . . . . . . .54
Control multi-projectors at the same time . . . . . . . . . . . . . . . . . .54
Selection of another projector . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Use of Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Serial port setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Control Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Use of Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Control the projector with Telnet . . . . . . . . . . . . . . . . . . . . . .64
Appendix:A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Examples of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Peer-To-Peer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
The gateway (Router) installed in the network . . . . . . . . . . . .67
Web browser setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Cookies enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Active Script/JavaScript enable . . . . . . . . . . . . . . . . . . . . . . .68
Proxy setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Setting examples: OS/Browsers . . . . . . . . . . . . . . . . . . . . . . . . .69
Windows 95/98 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Mac OS 8.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Product specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Port Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Appendix:B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
6
Preparation
Features
Web Management function
With this function, you can monitor projector functions such as power status, lamp
status, input mode, signal condition, lamp-use time, etc. through the network by using
the web browser installed on your computer.
E-Mail Alert function
Projector (Network Unit) sends messages to the registered e-mail addresses when a
lamp abnormality or power failure occurs with the projector. In this message, it
describes how to solve the cause of the problems. You can take efficient action for
quick recovery.
Power ON !
You’ve got mail !
7
Network Unit
OWNER’S MANUAL
Features
ENGLISH
Multi-control function
A single computer can control and set up the multiple computers at the same time.
Automatic On/Off using Timer function
Automatically turn on or off the projectors at specified date/day and time by using the
clock function.
Control port ready for external equipment via network
This product provides a serial port (RS-232C) for controlling external equipment. By
connecting the equipment which has a serial port, it can be controlled by a computer
via the network. * This product does not provide the interface driver software to control external equipment.
3rd floor
Meeting Room
5th floor
Theaters
Now it’s 11:30
I’m ready to turn ON, and
select Computer 1.
DVD
Player
8
Preparation
Operating Environment
To perform the management and setting up the projector using this product, the environment described below is required.
Operating System
Windows 95 / Windows 98 / Windows 2000 / Windows Me / Windows NT /
Windows XP
Mac OS 8.0 or later
Network
Network must handle Ethernet correctly and accept TCP/IP protocol.
Computer
The computer must provide a 10Base-T or 100Base-TX network card.
Web browser application*
● Microsoft Internet Explorer version 5.0 or later
● Netscape Navigator version 4.7 or later
* Use to control and set up the projector. The layout of pages in the browser
may slightly differ from each type of application or operating system you use.
Internet mail application*
● Microsoft Outlook ● Microsoft OutlookExpress
● Netscape Mail
* Required the internet e-mail application software to receive an e-mail alert sent
from this product. If you do not use the function E-mail Alert, this application is
not required.
The limitation of connection between this product and Hub or
Computer
Suitable LAN cables are limited by length and type as follows;
Connection Type of usable LAN cable Maximum length
Network Unit - Hub UTP Strait Cable with category 3 or 5 100m
Network Unit - Computer UTP Cross Cable with category 3 or 5 100m
✐ Category of LAN cable indicates the cable quality. Normally, cable with category 3 or 5 is
used for 10Base-T network and cable with category 5 is used for 100Base-TX network.
✐ There may be other limitations depending on your network environment or LAN specification.
Please consult your network administrator for further details.
Installation
1
9
Network Unit
OWNER’S MANUAL
ENGLISH
10
Installation
The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it.
Check package
1
Installation (p.12-14)
2
Network configuration (p.15-24)
3
Setting up is completed.
Please check the contents of a package. This product contains a Network Unit
and an owner’s manual (this manual). Also please check the name and function of each part (p.11).
1. Mount this product onto the projector.
2. Connect the LAN cable and join it to the network.
3. Confirm that the network menus are activated on the setting menu of the
projector.
Configure the network of the projector. Separate configurations must be set
up for each network to which the projector will be connected.
☛ Configure the network with the projector.
☛ Configure the network with the computer.
Flow of installation
The preparation is completed to control the projector connected to the network. At
next step, set up and control the projector via the network by using the web browser
installed on your computer. Please see chapter “2: Basic setting and operation” on
page 25.
11
Network Unit
OWNER’S MANUAL
Name and function of each part
ENGLISH
Name and function of each part
POWER
Serial port
This is used when controlling
the external equipment via the
network. (p.57)
Power indicator
This illuminates red when the
Network function is set ON in the
projector menu.
LAN port
Connecting the LAN cable.
(p.13)
SW lever
Presses the detection
SW on the rear panel of
the projector when this
unit is mounted.(p.12)
Computer Input
Terminal
Use as the Computer 2
RGB analog input terminal.
(p.12)
LINK indicator (Orange)
This illuminates orange when
the Network Unit is connected
to the network correctly.
ACT indicator (Green)
This turns on and off when
sending or receiving of data
✐ Do not touch the connector. It may damage the product.
Caution
!
Connector plug
Connect to the DVI terminal on
the projector. (p.12)
12
Installation
[1] Mounting
1 Disconnect the AC plug from the
projector.
2 Remove all of the hole covers (3
round type, 4 square type) on
the rear of the projector and
insert plug on this product to the
DVI connector.
Mount the unit as the switch
lever on the unit presses the
mount detecting switch on the
projector.
3 Tighten three screws by using a
coin etc.
✐ The AC cord must be disconnected from AC power outlet when mounting or removing this
product. It may damage the product.
✐ Do not connect the AC cord until after connecting the LAN cable and computer.
Caution
!
Mount detecting switch
hole covers
Note:
This network unit is connected to the DVI terminal on the projector, therefore, the digital
input does not be used when this unit is
mounted. The analog input of the Computer
2 can be used through the VGA terminal on
the network unit.
* Please use a VGA cable supplied with your
projector.
VGA cable
From computer
switch lever
13
Network Unit
OWNER’S MANUAL
Connection of LAN cable
ENGLISH
[2] Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair)
strait cable with RJ-45 plug. There are two different types of cables depending on
whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub
(10Base-T or 100Base-TX) to distribute the network cable if required.
1 Disconnect the AC plug from the projec-
tor.
2 Connect the UTP strait cable to the LAN
port on the Network Unit.
3 Connect the UTP strait cable to the hub.
✐ Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5.
When you connect the projector into the 100Base-TX network, use cable with category 5.
✐ The length of cable between hub and projector should be less than 100m.
Hub
(10Base-T, 100Base-TX)
UTP strait cable
Projector
14
Installation
[3] Confirmation of network menu activity
When installing this product onto the projector, the network on-screen menu items
for this product are activated automatically. If not activated, the product may not have
been installed correctly. Please check chapter “Mounting” on page 12.
Turn on the projector and display the menu on the screen.
Confirmation of network setting menu [Network]
Using the pointers on the remote
control unit or on the projector,
select the Network icon from the
Setting sub menu, and then press
the SELECT button once. Check if
the setting is On. If not, switch to
On by using the pointer 7/8. The
power indicator on this product will
illuminate red.
Press the SELECT button again,
the network setting menu appears
on the screen as shown on the
right. For further information about
network setting, please see chapter
“Network configuration”on next page.
Confirmation of password setting menu [Display]
Using the pointers on the remote
control unit or on the projector,
select the Display icon from the
Setting sub menu, and then press
the SELECT button twice. The
password setting menu appears on
the screen. If not, please check if
the function of the Network is On
as explained on previous item
“Confirmation of network setting
menu”. For further information
about password setting, please see
“Password setting menu” on page
17.
Password
0 0 0 0
SET
CANCEL
NETWORK SETTING
IP Address
Sub net
Gateway
DNS
192 168 0 2
255 255 255 0
0000
0000
SET
CANCEL
* The above on-screen display may differ from
the actual display depending on the functions
of the projector you use.
15
Network Unit
OWNER’S MANUAL
Network configuration
ENGLISH
Configure the network with the
projector
Tu rn the projector on and
display the network setting
menu on the screen.
Configure the network through
the projector's menu.
Restart the Network Unit
Configure the network with computer
Temporarily set up the computer's
network with the default network
number of the Network Unit
Restart the Computer, if required
Using the web browser and login to
the setting page of the Network Unit
by accessing the default IP address.
Change the network address you
want to connect to the existing
network through the setting menu
on the browser.
Restart the Network Unit
Reset to the computer's original
network configuration.
Completing the network configuration. Perform the
basic setting and operation of the projector by using
the web browser. Please see chapter "Basic Setting"
on page 25 for further information.
A B
Please see further
informatin on pages
16-17.
Please see further
informatin on pages
18-23.
Please see further
informatin on pages
25-31.
Example of projector's configuration
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
Example of projector's configuration
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Default Gateway : (blank)
DNS : (blank)
Default Network Address of the Network
Board
IP Address : 192.168.0.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
DNS : 0.0.0.0
Example of projector's configuration
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
p.18
p.16
Procedure of Connecting the projector to the network
[4] Network configuration
When you connect a projector to a network, the network number of projector must
be the same as the network you intend to connect. You should configure projector’s
network first. Make sure that the projector is connected to the network correctly.
There are 2 ways to configure the network, by using the
[A] projector’s menu, or by
using the
[B] computer . Refer to the chart below and use the method you prefer.
16
Installation
Configure the network with the projector
This example explains how to set the following configuration.
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
A
1 Selection of network menu [Network]
Turn on the projector and display the menu on the screen. Select the Network icon
from the Setting sub menu using the pointers, and then press the SELECT button
on the remote control or on the projector. Confirm that its mode is set On. If not,
change mode to On using the pointer 7/8.
2 Configuration for IP Address/ Subnet mask/Default Gateway*/DNS*
Press the SELECT button again, the network setting menu appears on the
screen. Enter the specified network
address. The right figure shows an example of a network configuration.
* In the network environments not using a Gateway or Router, the Default Gateway address
should be set to [0.0.0.0]. If you do not use the functions E-mail or DNS server, it is also set
[0.0.0.0] for the DNS address.
* The above on-screen display may differ from
the actual display depending on the functions
of the projector you use.
NETWORK SETTING
IP Address
Sub net
Gateway
DNS
192 168 1 201
192 168 1 1
255 255 255 0
0000
SET
CANCEL
17
Network Unit
OWNER’S MANUAL
Network configuration
ENGLISH
How to enter the numbers
To move the selection and change the values, Use the pointers ▲/▼/7/8 on the projector or on the remote control unit.
The 7/8 keys are used to move the selection item.
The ▲/ ▼ keys are used to change the number value.
3 Restart the Network Unit
Select the SET with the 7/8 keys and press the SELECT button again. The network configuration display disappears and the Network Unit begins restarting*
1
. It
takes about 60 seconds. Do not disconnect the AC cord from the projector.
Completing of installation
Now the installation is completed. The IP address of this projector was set to
“192.168.1.201”. Next, please see chapter “Basic setting and operation” on page
25. It describes basic setup and operation of the projector.
Password setting menu [Display]
A password can be set to restrict access to the setting pages of the projector using
the web browser. The default password is set “0000” as no password.
Use the projector’s menu and select the Display icon on the Setting sub menu, and
then press the SELECT button on the projector twice. The following setting display
appears on the screen. The numbers on the display indicates the current password.
To change the password, enter your desired number by using the pointers on the
projector or remote control unit, and then select the SET with the 7/8 keys and
press the SELECT button. The password setting display disappears and the Network
Unit begins restarting*
1
. It takes about 60 seconds. Do not disconnect the AC cord
from the projector.
Password
0 0 0 0
SET
CANCEL
*1 The Network Unit begins restarting automatically when the network configuration or pass-
word setting is changed. After the power indicator turns off twice, and it lights continuously.
This indicates that restarting is completed and it takes about 60 seconds.
✐ Password setting must be done when you connect the projector to the network. This setting
is carried out through the projector’s menu and also it can be set through the network using
the web browser. For further information please refer to chapter “Initial Setting/Password
setting” on page 29.
✐ Valid characters for password are only numeric numbers 0 to 9.
✐ This password is not to restrict the use of the projector. This password is to set the security
against the use of the projector through the network.
18
Installation
Configure the network with the computer
This example explains how to set the following configuration.
The default network configuration is set as follows.
Make sure that the projector is connected to the network and then connect the AC
cord to the outlet.
1 Temporarily*
1
set up your computer network configuration to the same IP network
group number as the Network Unit. For example, change your computer network
configuration as follows and restart the computer.
The network configuration of computer differs depending on each network environment or your computer. For further information, please see the next chapter
“Configure the network of computer”.
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Default Gateway : (blank)
DNS : (blank)
P
O
W
E
R
IP Address : 192.168.0.2
Subnet Mask : 255.255.255.0
Default Gateway : 0.0.0.0
DNS : 0.0.0.0
IP Address : 192.168.1.201
Subnet Mask : 255.255.255.0
Default Gateway : 192.168.1.1
DNS : 0.0.0.0
B
*1 Change your computer’s network configuration temporarily. After completing the set up for
the projector, you must set up again to the original network configuration for your computer.
It is recommended to make a note of those network settings.
19
Network Unit
OWNER’S MANUAL
Network configuration
ENGLISH
✐ If you use a cable to connect the projector and computer directly, without using a hub, you
must use a UTP cross cable. In this case, you cannot access the login page if the setting of
web browser is set to “Use proxy server”. It must be changed to the “Not use proxy server”. For further information, please see the “Web browser setting” on page 68.
✐ When you set up the network of projector which has a default setting by using the computer,
it must be carried out in the network which does not provide any gateways (routers). If it has
the gateways (routers), you must carry out the configuration by using the projector’s menu.
2 Configure the network of the projector by using the web browser.
1. Enter the IP address of the projector as the URL. The login page will be dis-
played and login. For further information, please see chapter “2: Basic Setting
and Operation” on page 25.
2. Configure the network through the setting page on the browser. For further
information, please see chapter “Network Configuration” on page 31.
Completing of installation
Now the installation is completed. The IP address of this projector has been set to
“192.168.1.201”. You must reset the network configuration of the computer to the
original and restart the computer.
Next, please see chapter “Basic Setting and Operation” on page 25. It describes how
to operate and set up the projector .
20
Installation
Configure the network of computer
When you use the projector through the network, the IP address of the pro-
jector must be the same IP network number of the existing network. Also it
is required to use the same IP network number of the computer to set up the projector. In the network included with the gateway (router), it must be used with the IP
network number specified by the gateway (router).
Configure the computer's network by following steps:
Windows 98/95/Me
This example explains how to set the following
network address.
1 Select the Control Panel menu from [Start] -
[Setting] menu.
2 Double click the Network icon on the control
panel window.
3 Select the TCP/IP*
1
item on the "Current
Network Component" column on the "Network
configuration" tab on the "Network" dialog window, and then press the Properties button.
4 Click IP Address tab, and then select the
Specified IP address. Enter the IP Address*
2
and Subnet Mask.
5 Click the Gateway tab and enter the Gateway
Address then press the Add button. Please
make sure that the entered gateway address
appears on the "Installed Gateway column.
✐ This setting is not needed if the network does not
provide the gateway (router).
6 Click the OK button, the setting window will
be closed and restart the computer.
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Gateway Address : 192.168.100.1
21
Network Unit
OWNER’S MANUAL
Configure the network of computer
ENGLISH
Windows 2000/NT4.0
This example explains how to set the following network address.
1 Select the Network and Dial-up Connections
menu from [Start] - [Settings] menu.
2 Click the Local Area Connection icon with
right button of the mouse and then select the
Properties menu from the popup menu. The
right window will appear on the screen.
3 Select the Internet Protocol(TCP/IP)
*1
on the
General tab of the "Local Area Connection
Properties" dialog window and then press the
Properties button.
4 On the "Internet Protocol (TCP/IP) Properties"
dialog window, select the Use the following IP
address button and then enter the IP
Address*
2
and Subnet mask.
5 Enter the Default gateway address.
✐ This setting is not needed if the network does
not provide the gateway (router).
6 Click the OK button, the setting window will
be closed.
✐ To change the configuration, you may need administrator privileges.
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Gateway Address : 192.168.100.1
*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-
umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.
*2 If the network already has the TCP/IP protocol set, enter with the same IP network number
for the IP address and Subnet mask.
*3 There are some ways to set up the network depending on your computer’s appearances.
22
Installation
Windows XP
This example explains how to set the following network address.
1 Select the Control Panel menu from the
[Start] menu. Click the Network and Internet
Connection and then click the Network on the
control panel.
2 Click the Local Area Connection icon with
right button of the mouse and then select the
Property menu. The right window will appear
on the screen.
3 Select the General tab on the "Local Area
Connection Properties" dialog window. Select
the Internet Protocol(TCP/IP)
*1
and then press
the Properties button.
4 On the "Internet Protocol (TCP/IP) Properties"
dialog window, select the Use the following
IP address button and then enter the IP
address*
2
and Subnet mask.
5 Enter the Default gateway address.
✐ This setting is not needed if the network does
not provide the gateway (router).
6 Click the OK button, the setting window will
be closed.
✐ To change the configuration, you may need admin-
istrator privileges.
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Gateway Address : 192.168.100.1
*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-
umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.
*2 If the network already has the TCP/IP protocol set, enter with the same IP network number
for the IP address and Subnet mask.
*3 There are some ways to set up the network depending on your computer’s appearances.
23
Network Unit
OWNER’S MANUAL
Configure the network of computer
ENGLISH
Macintosh
This example explains how to set the following network address.
1 Select TCP/IP*
1
menu from the
[Apple] - [Control Panel] menu.
2 Select Ethernet from the "Connect
via" pull down menu and Manually
from the "Configure" pull down
menu of the TCP/IP Control Panel.
3 Enter the IP Address*
2
and Subnet
Mask.
4 Enter the Router Address.
✐ This setting is not needed if the net-
work does not provide the gateway
(router).
5 Close the setting window and save
the setting.
IP Address : 192.168.0.5
Subnet Mask : 255.255.255.0
Gateway Address : 192.168.100.1
*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the col-
umn, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer.
*2 If the network already has the TCP/IP protocol set, enter with the same IP network number
for the IP address and Subnet mask.
24
Installation
Notice about system construction
For installation of multiple projectors into the same network with
Network Unit.
Do not install multiple projectors with the Network Units that have their default network settings to the same network. The use of the Network Units which have the
default IP address set to the same network settings will cause IP addresses to collide
and create a malfunction. When you install multiple projectors into the same network, configure the network with the following steps.
1. Change the IP address from the default IP address. To change the IP address, use
the network setting menu on the projector. Please see chapter “Network
Configuration” on page 15 for further information.
2. Make sure that there is no network equipment set with the same IP address in the
network, and then connect to the network.
3. When installing other projectors, follow the above steps to change the IP address
and connect to the network.
In case of installing the projector with Network Unit into the network
constructed with the DHCP/BOOTP server.
This Network Unit does not support the DHCP/BOOTP server. The static IP address
must be configured by the manual. To use this product in this network environment,
set it up so that the DHCP/BOOTP server does not assign the IP address configured
to this product for another device on the network. Please consult your network
administrator for further information.
Basic Setting and Operation
25
Network Unit
OWNER’S MANUAL
ENGLISH
2
26
Basic Setting and Operation
This chapter describes basic operations and settings for controlling the projector via a
network using this product. It is required that computer and projector are connected
to the network and the network address be properly configured.
Login or logout the setting page of the projector
1 Enter the IP address
Launch the web browser installed in
your computer, enter the IP address into
the "Address" on the browser and the
press the “Enter” key.
Enter the IP address that you configured in chapter “Network Configuration” on page 15. The
default IP address is [192.168.0.2].
2 Login
The following login page appears on the browser. Type the password and press the
Enter button. If you check the item “Save this password”, you will automatically
login* without entering the password for the next login.
[Note]
When accessing projector at first time or setting the no password [0000], the auto-login will
be performed and the next main setting page is displayed.
✐ The function of "Save this password" uses the cookies function and JavaScript function of the
web browser. If you cannot automatically login even if the "Save this password " is checked,
check your browser preference and change setting to "Accept all cookies" and “JavaScript
Enable” if required. Please see chapter “Appendix: Web browser setting/Cookies enable,
Active Script (JavaScript enable)” on page 68 for further information.
27
Network Unit
OWNER’S MANUAL
Login or logout the setting page of the projector
ENGLISH
3 Display of main setting page
The following main setting page of the projector is displayed. Perform the various
kinds of setting through this page. Click on the linked text to display the control
and setting pages.
☛ The main menu which can be set up and control the projector appears on the
left upper side of the page.
☛ The projectors connected to the network are listed on the left lower side of the
page. It can be listed on this sub menu when the projector connected to the
network is registered in the multi-control function. For further information,
please see chapter “Control the Multi Projectors” on page 51.
☛ On the main page, the control and status items for selected menu are dis-
played. The "Power & Status" page is displayed as the default. This page indicates the power control and current status of the projector. For further information, please see chapter “Controlling the projector” on page 35.
Main Menu
Described on page 35
Projector Selection menu
Described on page 56
Setting Page
Loading...