Eiki EIP-1600T User Manual

Download

EIP-1600T

OWNER’S MANUAL

EIKI INDUSTRIAL CO., LTD.

EIP-1600T_EN_a 06.1.16, 9:06 AM2

IMPORTANT

• For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information.

• Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10.

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth Blue : Neutral

Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

or and of the same rating as above, which is also indicated on the pin

Model No.: EIP-1600T

Serial No.:

• The wire which is coloured green-and-yellow must be connected to the terminal in the

plug which is marked by the letter E or by the safety earth symbol green-and-yellow.

or coloured green or

• The wire which is coloured blue must be connected to the terminal which is marked with

the letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

EIP-1600T_EN_a 06.1.24, 1:00 PM3

EIP-1600T_EN_a 06.1.24, 1:00 PM4

Before using the projector, please read this owner’s manual carefully.

Introduction

ENGLISH

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view

directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose

this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

DO NOT REMOVE COVER.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: FCC Regulations state that any unauthorized changes or modifications to

this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

EIP-1600T_EN_b 06.1.24, 1:01 PM1

U.S.A. ONLY

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector enters standby mode. During normal operation, when putting the projector into standby mode always use the STANDBY-ON button on the projector or the STANDBY button on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the owner’s manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

Declaration of conformity

EIKI PROJECTOR, MODEL EIP-1600T This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Responsible Party:

EIKI INTERNATIONAL, INC. 30251 Esperanza Rancho Santa Margarita, CA 92688-2132 TEL: 800-242-3454

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 54.

This EIKI projector uses a DMD panel. This very sophisticated panel contains 983,040 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

EIP-1600T_EN_b 06.1.24, 1:01 PM2

U.S.A. ONLY

How to Read this Owner’s Manual

■ The specifications are slightly different, depending on the model. However, you can connect and operate all models in the same manner.

• In this owner’s manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display.

Using the Menu Screen

ENTER button

Adjustment buttons (P/R/O/Q)

MENU button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press dMENU.

• The “Picture” menu screen for the selected input mode is displayed.

Press Q or O to select the menu

icon to adjust.

• The selected icon is highlighted.

Menu icon Menu screen

Note

• The “Fine Sync” menu is not available for INPUT 3 or INPUT 4.

Picture

Fine Sync

Options1

Options2

Example: “Picture” screen menu for INPUT 1 mode

Picture INPUT 1

Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue

SEL./ADJ.

RETURN

Adjustment buttons (P/R/O/Q)

• Press eRETURN to re-

turn to the previous screen when the menu is displayed.

Selected input mode

Menu icons

0 0 0 0 0 0

ENTER END

MENU button

ENTER button

RETURN button

Buttons used in this operation

Button used in this step

Standard

On-screen display

Info

........Indicates safeguards for using the projector.

.........Indicates additional information for setting up and operating the

Note

projector.

For Future Reference

EIP-1600T_EN_b 06.1.24, 1:01 PM3

PP. 60 and 61

IndexMaintenance Troubleshooting

P. 6 4P. 5 1

Contents

Preparing

Introduction

How to Read this Owner’s Manual ....... 3

Contents ............................................... 4

IMPORTANT SAFEGUARDS ............... 6

Accessories ........................................ 10

Part Names and Functions ................. 11

Inserting the Batteries .......................... 14

Usable Range ...................................... 15

Quick Start

Quick Start .......................................... 16

Using

Basic Operation

Turning the Projector On/Off .............. 28

Connecting the Power Cord ................ 28

Turning the Projector on ....................... 28

Turning the Power off (Putting the

Projector into Standby Mode) ........... 29

Image Projection................................. 29

Switching the Input Mode .................... 29

Adjusting the Projected Image ............ 30

Correcting Trapezoidal Distortion ........ 32

Resize Mode ......................................... 36

Useful Features

Operating with the Remote Control .... 38

Shifting the Projected Image Vertically

(Image Shift) ...................................... 38

Switching the Iris Setting ..................... 38

Freezing a Moving Image .................... 38

Selecting the Picture Mode .................. 38

Menu Items ......................................... 39

Using the Menu Screen ...................... 41

Menu Selections (Adjustments) ........... 41

Picture Adjustment (“Picture” menu) .. 43

Selecting the Picture Mode .................. 43

Adjusting the Image ............................. 43

Adjusting the Color Temperature ......... 44

Adjusting the Colors ............................. 44

Progressive ........................................... 44

Setup

Setting up the Projector ...................... 18

Setting up the Projector ....................... 18

Standard Setup (Front Projection) ....... 18

Ceiling-mount Setup ............................ 18

Projection (PRJ) Mode ......................... 19

Picture (Screen) Size and Projection

Distance ............................................. 20

Connections

Samples of Cables for Connection..... 22

Connecting to Video Equipment......... 23

Connecting to a Computer ................. 26

Controlling the Projector by a

Computer .......................................... 27

Reducing Image Noise (DNR) ............. 45

Switching the Iris Setting ..................... 45

Lamp Setting ........................................ 45

Computer Image Adjustment

(“Fine Sync” menu)........................... 46

Adjusting the Computer Image ........... 46

Special Modes Setting ......................... 46

Auto Sync (Auto Sync Adjustment) ..... 46

Checking the Input Signal ................... 46

Using the “Options” Menu................... 47

Adjusting the Image Position ............... 47

Adjusting the Overscan ....................... 47

Adjusting the Vertical Size of the Display

(Subtitle Setting) ................................ 47

Setting On-screen Display ................... 48

Setting the Video System ..................... 48

Signal Type Setting .............................. 48

Selecting the HDMI Setting .................. 48

Selecting the Background Image ........ 48

Auto Power Off Function ...................... 49

Checking the Lamp Life Status ........... 49

Reversing/Inverting Projected

Images ............................................... 49

Selecting the Transmission Speed

(RS-232C) .......................................... 50

Reducing the Power Consumption When

the Power Is in Standby Mode .......... 50

Fan Mode Setting ................................. 50

Returning to the Default Settings ......... 50

Selecting the On-screen Display

Language ........................................... 50

EIP-1600T_EN_b 06.1.24, 1:01 PM4

Reference

Appendix

Maintenance ....................................... 51

Maintenance Indicators ...................... 52

Regarding the Lamp ........................... 54

Lamp ..................................................... 54

Caution Concerning the Lamp ............ 54

Replacing the Lamp ............................. 54

Removing and Installing

the Lamp Unit .................................... 55

Resetting the Lamp Timer .................... 56

Connecting Pin Assignments ............. 57

RS-232C Specifications and Command

Settings ............................................ 58

Computer Compatibility Chart ............ 59

Troubleshooting .................................. 60

Specifications ..................................... 62

Dimensions ......................................... 63

Index ................................................... 64

EIP-1600T_EN_b 06.1.24, 1:01 PM5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product

and save these instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with

a grounding terminal. This plug will only fit into a grounding type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.

EIP-1600T_EN_b 06.1.24, 1:01 PM6

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

e. If the product has been dropped or damaged

in any way.

f. When the product exhibits a distinct change

in performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21. Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

• DLP\ (Digital Light Processing), DMD\ (Digital Micromirror Device) and BrilliantColor™ are trademarks of Texas Instruments, Inc.

• Microsoft

and Windows® are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Macintosh

is a registered trademark of Apple Computer, Inc. in the United States and/or

other countries.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

• All other company or product names are trademarks or registered trademarks of their respective companies.

• Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.

EIP-1600T_EN_b 06.1.24, 1:01 PM7

Observe the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest EIKI Authorized Dealer or Service Center for replacement. See “Replacing the Lamp” on page 54.

Caution concerning the setup of the projector

■ For minimal servicing and to maintain high image quality, EIKI recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by an EIKI Authorized Dealer or Service Center.

Do not set up the projector in places exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

Caution regarding placing of the projector

■ Place the projector on a level site within the adjustment range (8 degrees) of the adjust-

ment foot.

■ After the projector is purchased, a faint smell from the vent may appear when the power is first turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 4,900 feet (1,500 meters) or more)

■ When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

Warning about placing the projector in a high position

■ When placing the projector in a high position, ensure that it is secured carefully to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■ Protect the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long hours will cause eye strain. Be sure to occasionally rest your eyes.

Avoid locations with extremes of temperature.

■ The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the exhaust and intake vents.

■ Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.

■ Be sure that the intake vent and the exhaust vent are not obstructed.

■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 52 and 53.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

EIP-1600T_EN_b 06.1.24, 1:01 PM8

■ When turning off the projector, the cooling fan runs to decrease the internal temperature for a while. Unplug the power cord after the cooling fan stops. The period the cooling fan runs will vary, depending on the circumstances and the internal temperature.

Caution regarding usage of the projector

■ When using the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. Before moving the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

■ Do not carry the projector by holding the lens.

■ When storing the projector, re-attach the lens

cap. (See page 11).

■ Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.

Other connected equipment

■ When connecting a computer or other audiovisual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.

■ Please read the owner’s manuals of the pro- jector and the equipment to be connected for instructions on how to make the connections.

Using the projector in other countries

■ The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, be sure to use an appropriate power cord for the country you are in.

Temperature monitor function

■

If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter standby mode. Refer to “Maintenance Indicators” on page 52 for details.

Info

• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

• Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops.

EIP-1600T_EN_b 06.1.24, 1:01 PM9

Accessories

Supplied accessories

Remote control

Video cable

(10' (3.0 m))

QCNWGA097WJPZ

Power cord*

(1) (2)

For U.S. and

Canada, etc.

(6' (1.8 m))

QACCDA007WJPZ

* Use the power cord that corresponds to the wall outlet in your country.

Two R-03 batteries

(“AAA” size, UM/SUM-4,

HP-16 or similar)

DIN-D-sub

RS-232C adaptor

(5 57/64" (15 cm))

QCNWGA015WJPZ

For Europe, except U.K.

(6' (1.8 m))

QACCVA011WJPZ

• Owner’s manual

• Quick Guide

Optional accessory

■ Lamp unit

AH-11201

Lens cap (attached)

EIP-1600T_EN_c 06.1.24, 1:02 PM10

Part Names and Functions

Numbers in Z refer to the main pages in this owner’s manual where the topic is explained.

Projector

Top View

Power indicator

28, 5228, 52

Lamp indicator

STANDBY-ON button

For turning the power on and putting the projector into standby mode.

ENTER button

For setting items selected or adjusted on the menu.

RESIZE button

For switching the screen size.

Front View

Focus ring

For adjusting the focus.

HEIGHT ADJUST lever

Temperature warning

indicator

INPUT buttons (P/R)

For switching input mode 1, 2, 3, 4, 5 or 6.

MENU button

For displaying adjustment and setting screens.

Adjustment buttons

(P/R/O/Q)

For selecting menu items.

Intake vent

Zoom ring

For enlarging/ reducing the picture.

Remote control

sensor (front)

Push both sides of the lens cap to attach or remove.

EIP-1600T_EN_c 06.1.24, 1:02 PM11

Part Names and Functions (Continued)

Numbers in Z refer to the main pages in this owner’s manual where the topic is explained.

Rear View

Exhaust vent

Intake vent

AC socket

Connect the supplied Power cord.

Rear adjustment foot

Terminals

65 4 1 23 7

Terminal Description

INPUT 1, 2 terminal

Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.).

INPUT 3 terminal

Connecting video equipment with S-video output terminal (VCR, DVD

player, etc.).

INPUT 4 terminal

Connecting video equipment without S-video output terminal.

INPUT 5 terminal

■

Connecting the computer.

■ Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.).

INPUT 6 terminal

Connecting video equipment with HDMI output terminal.

RS-232C terminal

Connecting the computer to control the projector.

TRIGGER terminal

When the projector is turned on, a control signal (DC 12V) outputs from this terminal. If an electric screen or other compatible device is connected, it can be turned on when the projector is turned on.

Remote control

sensor (rear)

Kensington

Security Standard connector

Page

—

EIP-1600T_EN_c 06.1.24, 1:02 PM12

Numbers in Z refer to the main pages in this owner’s manual where the topic is explained.

ON button

For turning the power on.

INPUT 1, 2, 3, 4, 5 and 6

STANDBY button

For putting the projector into the standby mode.

KEYSTONE button

For entering the Keystone Correction mode.

RETURN button

For returning to the previous menu screen during menu operations.

AUTO SYNC button

For automatically adjusting images when connected to a computer.

RGB/COMP. button

For switching to the respective input signal type.

FREEZE button

For freezing images.

buttons

For switching to the respective input modes.

MENU button

For displaying adjustment and setting screens.

Adjustment buttons

(P/R/O/Q)

• For selecting menu items.

• For adjusting the Keystone Correction when in the Keystone Correction mode.

ENTER button

For setting items selected or adjusted on the menu.

RESIZE button

For switching the screen size (STRETCH, SIDE BAR, etc.).

PICTURE MODE button

For selecting the appropriate picture.

Backlight button

For lighting all buttons on the remote control.

Using the Kensington Lock on the projector

• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

EIP-1600T_EN_d 06.1.24, 1:02 PM13

IRIS button

For switching “HIGH BRIGHTNESS MODE”, “MEDIUM MODE” and “HIGH CONTRAST MODE”.

IMAGE SHIFT buttons

For shifting the projected image vertically.

Part Names and Functions (Continued)

Inserting the Batteries

Press the P mark on the cover and slide it

in the direction of the arrow.

Insert the batteries.

• Insert the batteries making sure the polarities

correctly match the m and n marks inside the battery compartment.

Attach the cover and slide it until it clicks

into place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.

Caution

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries. This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and then remove them using a cloth.

• The batteries included with this projector may run down in a short period, depending on how they are kept.

Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

EIP-1600T_EN_d 06.1.24, 1:02 PM14

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Remote control sensor (front)

30°

Remote control signal transmitters

30°

Remote control

Note

• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

23n (7 m)

Remote control sensor (rear)

23n (7 m)

Remote control

30°

Remote control signal transmitters

When using the remote control

• Ensure that you do not drop, expose to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp.

EIP-1600T_EN_d 06.1.24, 1:02 PM15

Quick Start

This section shows the basic operation (projector connecting with the video equipment). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the video equipment is explained using one example.

STANDBY-ON

button

INPUT buttons

Focus ring

Zoom ring

HEIGHT

ADJUST lever

STANDBY button

ON button

INPUT 4 button

KEYSTONE button

Adjustment buttons

(P/R/O/Q)

ENTER button

1. Place the projector facing a wall or a screen

_P. 18

2. Connect the projector to the video equipment and plug the power cord into the AC socket of the projector

To INPUT 4 terminal

Connect the audio output of

AC socket

any video devices to an appropriate audio device.

3. Remove the lens cap and turn the projector on

On the

projector

On the remote

control

_PP. 22–28

_P. 28

EIP-1600T_EN_e 06.1.24, 1:03 PM16

4. Turn the video equipment on and start playback

5. Select the INPUT mode

Select the “INPUT 4” using the INPUT buttons on the projector or the INPUT 4 button on the remote control.

projector

On the

On the remote

control

On-screen display

_P. 29

INPUT 4

• When pressing the INPUT buttons on the projector, input mode switches in the following order:

• Pressing the INPUT buttons on the remote control also allows you to switch the input mode.

6. Adjust the focus, image size, and projector angle

1. Adjust the focus by

Correct trapezoidal distortion (GEOMETRIC ADJUSTMENT)

1. Press c KEYSTONE on the remote control.

2. Press P/R/O/Q on the remote control to set the upper-left position of the projected image.

3. Press i ENTER on the remote control to set the position.

4. Follow steps 2 and 3 to also set the upper-right, lower-right, and lower-left positions of the projected image.

• When you confirm the lower left position, the screen adjustments will be set and setup will

INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6

turning the focus ring.

Focus ring

end.

2. Adjust the projection image size by turning the zoom ring.

Zoom ring

_PP. 30, 31

3. Adjust the projector angle using the HEIGHT ADJUST lever.

_PP. 32–35

8. Turn the Power off

Press the STANDBY-ON button on the projector or the STANDBY button on the remote control, and then press the button again while the confirmation message is displayed, to put the projector into standby mode.

On the

projector

• Unplug the power cord from the AC outlet after the cooling fan stops.

EIP-1600T_EN_e 06.1.24, 1:03 PM17

On the remote

control

On-screen Display

_P. 29

Setting up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality.

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according to the desired picture size. (See page 20.)

Example of standard setup

Side View

Screen

Lens center

Note

• Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Distance”.

Ceiling-mount Setup

■ It is recommended that you use the optional EIKI ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest EIKI Authorized Dealer or Service Center to obtain the recommended ceilingmount bracket (sold separately).

■ Invert the image by setting “Ceiling + Front” in “PRJ Mode”. See page 49 for use of this function.

EIP-1600T_EN_f 06.1.24, 1:03 PM18

Projection (PRJ) Mode

The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ Mode in “Options2” menu. See page 49.)

■ Table mounted, front projection

Menu item ➞ “Front”

■ Table mounted, rear projection (with a translucent screen)

■ Ceiling mounted, front projection

Menu item ➞ “Ceiling + Front”

■ Ceiling mounted, rear projection (with a translucent screen)

Menu item ➞ “Rear” Menu item ➞ “Ceiling + Rear”

Indication of the Projection Image Size and Projection Distance

Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Distance”. Example: When using a wide screen (16:9)

Picture (Screen) Size

300"

200"

100"

80" 60"

52"

70"

29"

87"

39"

49"

174"

98"

261"×147"

EIP-1600T_EN_f 06.1.24, 1:03 PM19

5'11

6'11

"–

(1.8 m

– 2.1 m)

7'11

(2.4 m

"–

9'2

2.8 m)

–

9'11

11'6

"–

(3.0 m

3.5 m)

–

19'10

(6.0 m

22'11

"–

7.0 m)

–

29'9

(9.1 m

34'

–

– 10.5 m)

Projection Distance

Setting up the Projector (Continued)

Picture (Screen) Size and Projection Distance

The projection screen size varies according to the distance from the lens of the projector to the screen. Install the projector so that projected images are projected onto the screen at the optimum size by referring to the table below. Use the values in the table as a reference when installing the projector.

When using a wide screen (16:9) and projecting 16:9 image

Picture (Screen) size Projection distance [L]

Diag. [χ] Width Height

300 (762 cm) 270 (686 cm) 250 (635 cm) 200 (508 cm) 150 (381 cm) 100 (254 cm)

80 (203 cm) 70 (178 cm) 60 (152 cm) 40 (102 cm)

: Picture (Screen) size (diag.) (in/cm) L: Projection distance (ft/m) L1: Minimum projection distance (ft/m) L2: Maximum projection distance (ft/m) H: Distance from the lens center to the bottom of the image (in/cm) S: Adjustable range of image position (in/cm) See page 47.

261 (664 cm) 235 (598 cm) 218 (553 cm) 174 (443 cm) 131 (332 cm)

87 (221 cm) 70 (177 cm) 61 (155 cm) 52 (133 cm) 35 (89 cm)

147 (374 cm) 132 (336 cm) 123 (311 cm)

98 (249 cm) 74 (187 cm) 49 (125 cm) 39 (100 cm) 34 (87 cm) 29 (75 cm) 20 (50 cm)

Minimum [L1] Maximum [L2]



9 (9.1 m)



9 (8.2 m)



9 (7.5 m)



10 (6.0 m)



10 (4.5 m)



11 (3.0 m)



11 (2.4 m)



11 (2.1 m)



11 (1.8 m)



0 (1.2 m)



5 (10.5 m)



11 (9.4 m)



8 (8.7 m)



11 (7.0 m)



2 (5.2 m)



6 (3.5 m)



2 (2.8 m)



0 (2.4 m)



11 (2.1 m)



7 (1.4 m)

When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)

Picture (Screen) size Projection distance [L]

Diag. [χ]

300 (762 cm) 270 (686 cm) 250 (635 cm) 200 (508 cm) 150 (381 cm) 100 (254 cm)

80 (203 cm) 70 (178 cm) 60 (152 cm) 40 (102 cm)

Width Height

240 (610 cm) 216 (549 cm) 200 (508 cm) 160 (406 cm) 120 (305 cm)

80 (203 cm) 64 (163 cm) 56 (142 cm) 48 (122 cm) 32 (81 cm)

180 (457 cm) 162 (411 cm) 150 (381 cm) 120 (305 cm)

90 (229 cm) 60 (152 cm) 48 (122 cm) 42 (107 cm) 36 (91 cm) 24 (61 cm)

Minimum [L1] Maximum [L2]



4 (11.1 m)



9 (10.0 m)



4 (9.2 m)



3 (7.4 m)



2 (5.5 m)



1 (3.7 m)



8 (3.0 m)



6 (2.6 m)



3 (2.2 m)



10 (1.5 m)



1 (12.8 m)



10 (11.5 m)



1 (10.7 m)



1 (8.6 m)



0 (6.4 m)



0 (4.3 m)



3 (3.4 m)



10 (3.0 m)



5 (2.6 m)



7 (1.7 m)

Distance from the lens center

to the bottom of the image [H]

/32 (53 cm)

21

/16 (48 cm)

18

/32 (45 cm)

17

/64 (36 cm)

14

/64 (27 cm)

10

/64 (18 cm)

7

/64 (14 cm)

5

/32 (12 cm)

4

/64 (11 cm)

4

/64 ( 7 cm)

2

The formula for picture size and projection distance

[Feet/inches]

L1 (ft) = 0.03019χ / 0.3048 L2 (ft) = 0.03493χ / 0.3048 H (in) = - 0.17808χ / 2.54 S (in) = ±0.04151χ / 2.54

Distance from the lens center

to the bottom of the image [H]

/64 (65 cm)

25

/64 (59 cm)

23

/64 (54 cm)

21

/32 (44 cm)

17

/8 (33 cm)

12

/64 (22 cm)

8

/64 (17 cm)

6

6 (15 cm)

/64 (13 cm)

5

/16 (9 cm)

3

The formula for picture size and projection distance

[Feet/inches]

L1 (ft) = 0.03694χ / 0.3048 L2 (ft) = 0.04275χ / 0.3048 H (in) = - 0.21794χ / 2.54 S (in) = ±0.0508χ / 2.54

Adjustable range of

image position [S]

/32 (12.5 cm)

4

/32 (11.2 cm)

4

/64 (10.4 cm)

4

/64 (8.3 cm)

3

/64 (6.2 cm)

2

/64 (4.2 cm)

1

/16 (3.3 cm)

1

/64 (2.9 cm)

1

/64 (2.5 cm)



/32 (1.7 cm)



[m/cm]

L1 (m) = 0.03019 L2 (m) = 0.03493 H (cm) = - 0.17808 S (cm) = ±0.04151

χ χ

Adjustable range of

image position [S]

6 (15.2 cm)

5

/32 (13.7 cm)

5 (12.7 cm)

4(10.2 cm) 3 (7.6 cm) 2 (5.1 cm)

/32 (4.1 cm)

1

/32 (3.6 cm)

1

/64 (3.0 cm)

1

/64 (2.0 cm)



[m/cm]

L1 (m) = 0.03694 L2 (m) = 0.04275 H (cm) = - 0.21794 S (cm) = ±0.0508

χ χ

EIP-1600T_EN_f 06.1.24, 1:04 PM20

When using a normal screen (4:3) and projecting 16:9 image

Picture (Screen) size Projection distance [L]

Diag. [χ]

300 (762 cm) 270 (686 cm) 250 (635 cm) 200 (508 cm) 150 (381 cm) 100 (254 cm)

80 (203 cm) 70 (178 cm) 60 (152 cm) 40 (102 cm)

Width

240 (610 cm) 216 (549 cm) 200 (508 cm) 160 (406 cm) 120 (305 cm)

80 (203 cm) 64 (163 cm) 56 (142 cm) 48 (122 cm) 32 (81 cm)

Height

180 (457 cm) 162 (411 cm) 150 (381 cm) 120 (305 cm)

90 (229 cm) 60 (152 cm) 48 (122 cm) 42 (107 cm) 36 (91 cm) 24 (61 cm)

Minimum [L1] Maximum [L2]



27 24 22 18

13 9 7

6 5 3

3 (8.3 m)



7 (7.5 m)



9 (6.9 m)



2 (5.5 m)



8 (4.2 m)



1 (2.8 m)



3 (2.2 m)



4 (1.9 m)



5 (1.7 m)



8 (1.1 m)



7 (9.6 m)



5 (8.7 m)



4 (8.0 m)



0 (6.4 m)



9 (4.8 m)



6 (3.2 m)



5 (2.6 m)



4 (2.2 m)



4 (1.9 m)



2 (1.3 m)

Note

• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the bottom of the image [H]”.

• Allow a margin of error in the values in the diagrams.

• Values with a minus (-) sign indicate the distance from the lens center below the bottom of the image.

Distance from the lens center to

the bottom of the image [H]

/16 (49 cm)

19

/8 (44 cm)

17

/32 (41 cm)

16

/8 (33 cm)

12

/32 (25 cm)

9

/16 (16 cm)

6

/64 (13 cm)

5

/2 (11 cm)

4

/64 (10 cm)

3

/64 (7 cm)

2

The formula for picture size and projection distance

[Feet/inches]

L1 (ft) = 0.02771χ / 0.3048 L2 (ft) = 0.03206χ / 0.3048 H (in) = - 0.16346χ / 2.54 S (in) = ±0.0381χ / 2.54

Adjustable range of

image position [S]

/2 (11.4 cm)

4

/64 (10.3 cm)

4

/4 (9.5 cm)

3

3 (7.6 cm)

/4 (5.7 cm)

2

/2 (3.8 cm)

1

/64 (3.0 cm)

1

/64 (2.7 cm)

1

/32 (2.3 cm)



/32 (1.5 cm)



[m/cm]

L1 (m) = 0.02771 L2 (m) = 0.03206 H (cm) = - 0.16346 S (cm) = ±0.0381

χ χ

EIP-1600T_EN_f 06.1.24, 1:04 PM21

Samples of Cables for Connection

•

For more details of connection and cables, refer to the owner’s manual of the connecting equipment.

• You may need other cables or connectors not listed below.

Equipment

Audio-visual equipment

Input

Signal

HDMI

video

Cable

HDMI cable (commercially available)

Terminal on the

projector

INPUT6

Camera/ video game

Computer

Compo-

nent

video

S-video

Video

Compo-

nent

video

S-video

Video

RGB video

S-video cable (commercially available)

Video cable (supplied)

Cables for a camera or a video game

RGB cable (commercially available)

INPUT1, 2Component cable (commercially available)

INPUT3

INPUT4

INPUT1, 2

INPUT3

INPUT4

INPUT5

EIP-1600T_EN_g 06.1.24, 1:04 PM22

Connecting to Video Equipment

Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector first and then the other devices.

When connecting the component video equipment to the component input terminal on the projector (INPUT1 or INPUT2)

To component output (Y, CB/PB, CR/PR) terminal

DVD, etc.

To INPUT1 or INPUT2 terminal

Component cable (commercially available)

EIP-1600T_EN_g 06.1.24, 1:04 PM23

Connecting to Video Equipment (Continued)

When connecting to equipment with S-video output terminal (INPUT3)

To S-video output terminal

When connecting to equipment with video output terminal (INPUT4)

DVD, etc.

To INPUT3 terminal

S-video cable (commercially available)

To video output terminal

EIP-1600T_EN_g 06.1.24, 1:04 PM24

DVD, etc.

Video cable

Supplied

accessory

Video cable

To INPUT4 terminal

When connecting to equipment with HDMI output teminal (INPUT6)

HDMI is a new specialized interface capable of delivering a video and audio signal to the terminal using just one cable. Since this projector does not support an audio signal by itself, use an amplifier or other audio device. For video connection, use a cable that conforms to HDMI standards. Using cables that do not conform to HDMI standards may result in a malfunction.

To HDMI output terminal

Note

• HDMI (High Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.

• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital video signal does not degrade when transmitted, and a high-quality image with a simple connection can be enjoyed.

• When a DVI to HDMI conversion cable is connected to the HDMI terminal, a proper picture may not be displayable.

HDMI compatible device

To INPUT6 terminal

HDMI cable (type A) (commercially available)

EIP-1600T_EN_g 06.1.24, 1:04 PM25

Connecting to a Computer

When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.

Ensure that you have read the owner’s manuals of the devices to be connected before making connections.

Computer

To RGB output terminal

RGB cable (commercially available)

Note

• See page 59 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the computer’s external output port is switched on. Refer to the specific instructions in the owner’s manual of your computer to enable your computer’s external output port.

• The INPUT5 terminal is also compatible with a component video signal so that you can connect the projector to a DVD player with a component output terminal. For details, contact your nearest EIKI Authorized Dealer or Service Center.

Supplied

accessory

To INPUT5 terminal

EIP-1600T_EN_g 06.1.24, 1:04 PM26

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. See page 58 for detail.

When connecting to a computer using an RS-232C serial control cable and a DIND-sub RS-232C adaptor

Supplied

accessory

Computer

Note

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.

• See page 58 for connection of an RS-232C serial control cable.

DIN-D-sub RS-232C adaptor

To RS-232C terminal

DIN-D-sub RS-232C adaptor

RS-232C serial control cable (cross type, commercially available)

To RS-232C terminal

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.

EIP-1600T_EN_g 06.1.24, 1:04 PM27

Turning the Projector On/Off

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector.

Turning the Projector on

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 23 to 28.)

Remove the lens cap and press o STANDBY-ON on the projector or bON on the remote control.

Note

• About the Lamp Indicator The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on. Blinking in green: The lamp is warming up

or shutting down.

Red:The lamp is shut down abnormally

or the lamp should be replaced.

• When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

• If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.

Supplied

accessory

AC socket

Power cord

Info

• English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 50.

Lamp indicator

Power indicator

STANDBY-ON button

ON button

EIP-1600T_EN_h 06.1.24, 1:05 PM28

Turning the Power off (Putting the Projector into Standby Mode)

Press oSTANDBY-ON on the pro-

jector or aSTANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into standby mode.

Unplug the power cord from the AC

outlet after the cooling fan stops.

• The power indicator on the projector blinks in red while cooling.

• The power indicator changes to green when the projector finishes cooling.

STANDBY button

On-screen Display (confirmation message)

Info

• Do not unplug the power cord during projection or cooling fan operation. This can cause damage due to rise in internal temperature, as the cooling fan also stops.

Image Projection

Switching the Input Mode

Select the appropriate input mode for the connected equipment.

Press the appropriate INPUT button on the remote control to select the desired input mode.

• When pressing INPUT (P/R) on the projector,

input mode switches in the following order:

INPUT1 INPUT2 INPUT3

INPUT6 INPUT5 INPUT4

INPUT buttons

EIP-1600T_EN_h 06.1.24, 1:05 PM29

Image Projection (Continued)

Adjusting the Projected Image

1 Adjusting the Focus

You can adjust the focus with the focus ring on the projector.

Rotate the focus ring to adjust the focus while watching the projected image.

2 Adjusting the Screen Size

You can adjust the screen size using the zoom ring on the projector.

Rotate the zoom ring to enlarge or shrink the screen size.

3 Adjusting the Height

The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector.

When the screen is above the projector, the projection image can be made higher by adjusting the projector.

Zoom ring

Focus ring

Lift the projector to adjust its

height while lifting the HEIGHT ADJUST lever.

Remove your hands from the

HEIGHT ADJUST lever of the projector after its height has been finely adjusted.

• The angle of projection is adjustable up to 8 degrees from the surface on which the projector is placed.

EIP-1600T_EN_h 06.1.24, 1:05 PM30

HEIGHT ADJUST lever

Make small adjustments.

Use the rear adjustment foot to

make the projector level.

• The projector is adjustable ±1 degree from the standard position.

Note

• When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See page 32.)

Info

• Do not apply too much pressure on the projector when the front adjustment foot comes out.

• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.

• Hold the projector firmly while lifting or carrying.

• Do not hold by the lens area.

Rear adjustment foot

EIP-1600T_EN_h 06.1.24, 1:05 PM31

Image Projection (Continued)

Correcting Trapezoidal Distortion

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

There are the two types of the Keystone Correction.

1) The “GEOMETRIC ADJUSTMENT” method corrects trapezoidal distortion by specifying 4 marks on the screen.

2) The “H & V KEYSTONE” method features corrections to 2 axes (horizontal and vertical) based on numerical values.

KEYSTONE button

Adjustment buttons (P/R/O/Q)

RETURN button

ENTER button

EIP-1600T_EN_h 06.1.24, 1:05 PM32

Selecting the Type of Correction

Select the Keystone correction method. Press c KEYSTONE on the remote control.

• “GEOMETRIC ADJUSTMENT” will be

displayed.

• Each time c KEYSTONE is pressed, the

display toggles as follows:

GEOMETRIC

ADJUSTMENT

The display disappears.

H & V KEYSTONE

Note

• When corrections are made with Keystone correction, the changes are saved even if the power cord is unplugged.

• Since Keystone correction digitally corrects the signal, resolution may slightly decrease when it is used. Moiré patterns and line distortions may also be visible in detailed images. However, this is not a malfunction.

• If you cannot correct trapezoidal distortion with Keystone correction, change the placement position of the projector.

• Straight lines and the edges of the displayed image may appear jagged, when adjusting the Keystone setting.

• Also read “About Copyrights” on page 37.

GEOMETRIC ADJUSTMENT

H & V KEYSTONE

For correcting an image by designating the corner of the projected image. (See page 34.)

For correcting an image by designating the horizontal or vertical axes. (See page 35.)

EIP-1600T_EN_h 06.1.24, 1:05 PM33

Image Projection (Continued)

GEOMETRIC ADJUSTMENT

Note

• To use the “GEOMETRIC ADJUSTMENT”, set RESIZE to “STRETCH”. (See page 36.)

Press c KEYSTONE on the re-

mote control repeatedly until “GEOMETRIC ADJUSTMENT” is displayed.

Adjust the focus, size, and projec-

tion angle so that the screen edges line up into the blue area.

• Line up the screen edges into the blue area as closely as possible.

Press P, R, O or Q to move the

position for the upper left of the image.

• Adjust the screen until the displayed red arrows line up in the upper left.

Press i ENTER to set the posi-

tion.

• The arrow in the upper right turns red.

Repeat the same procedure with

the positions for the upper right, lower right and lower left of the image.

• When you press e RETURN at this point, you will return to the previous screen.

• If you press e RETURN before adjusting the upper left corner, the Reset Confirmation screen displays.

• When you confirm the lower left posi-

tion, the screen adjustments will be set and the “GEOMETRIC ADJUSTMENT” mode will end.

R On-screen display

Adjust upper left corner

GEOMETRIC ADJUSTMENT ADJUST NEXT

Geometric Adjustment

Blue

area

Screen

Upper Left Upper Right

Lower Left Lower Right

RESET END

Note

• The placement of the screen and the projector may result in the image aspect ratio becoming slightly distorted.

EIP-1600T_EN_h 06.1.25, 6:33 AM34

H & V KEYSTONE

Project the image and adjust the

focus, image size, and projection angle.

Press c KEYSTONE on the re-

mote control repeatedly until “H & V KEYSTONE” is displayed.

• When the “GEOMETRIC ADJUSTMENT” mode has been used to adjust the image, a confirmation screen displays before the “H & V KEYSTONE” screen, asking if you want to reset the adjustments or not. Then select RESET.

R On-screen display

H&V KEYSTONE

END

ENTER

ADJUST

RESET

Press P or R on the remote con-

trol to align the left and right sides of the projected image.

Press O or Q on the remote con-

trol to align the upper and lower sides of the projected image.

Press c KEYSTONE or i ENTER

on the remote control and the “H&V KEYSTONE” mode ends.

Note

• If adjustments are made using both “H KEYSTONE” and “V KEYSTONE” at the same time, the image aspect ratio may become slightly distorted.

• When adjusting “H KEYSTONE” and “V KEYSTONE” at the same time, the values of adjustable angles for each setting become smaller.

• The adjustable value of the “V KEYSTONE” becomes extremely small when “H KEYSTONE” is made to be the maximum value.

Vertical Keystone Correction

(Adjustment with P / R)

Horizontal Keystone Correction

(Adjustment with O / Q)

EIP-1600T_EN_h 06.1.24, 1:05 PM35

Image Projection (Continued)

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “STRETCH”, “SIDE BAR”, “CINEMA ZOOM” or “DOT

BY DOT (Computer input only)” image.

Press RESIZE on the projector or jRESIZE on the remote control.

On the projector

On the remote control

RESIZE button

VIDEO

RESIZE button

• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.

Input Signal

DVD / Video Image type

4:3 aspect ratio

480I, 480P, 576I,

576P, NTSC, PAL,

SECAM

Letter box

Squeezed

16:9 aspect ratio

STRETCH SIDE BAR

Output screen image

CINEMA ZOOM

540P, 720P, 1080I

16:9 aspect ratio

: Cutout area on which images cannot be projected.

EIP-1600T_EN_h 06.1.24, 1:06 PM36

Computer

Input Signal

Computer

Resolution lower than

XGA

(1024K768)

1280K720

: Cutout area on which images cannot be projected.

Image

type

4:3 aspect

ratio

4:3 aspect

ratio

16:9 aspect

ratio

STRETCH

Output screen image

SIDE BAR

CINEMA

ZOOM

DOT BY DOT

About Copyrights

• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size.

• The use of the Resize, Keystone Correction, Subtitle, or Overscan function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.

• While watching non-widescreen images (4:3), if you use the RESIZE function to fill the screen or use the Overscan function to change the aspect ratio of a fixed-ratio input signal, parts of the outer edge of the image will be cut off or distorted. To watch original images as the producers intended, set RESIZE to “SIDE BAR” and Overscan to its default setting.

EIP-1600T_EN_h 06.1.24, 1:06 PM37

Operating with the Remote Control

Shifting the Projected Image Vertically (Image Shift)

For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players or other connected devices.

Press PIMAGE SHIFT.

• The image moves up.

Press RIMAGE SHIFT.

• The image moves down.

Note

• The Image Shift function operates when “Resize” is not set to “DOT BY DOT”.

• For details on Image Shift, see page 47.

Switching the Iris Setting

This function controls the quantity of the projected light and the contrast of the image.

Press lIRIS.

• Each time the button is pressed while the display is on, the mode is switched in the following order:

HIGH BRIGHTNESS MODE MEDIUM MODE

HIGH CONTRAST MODE

IMAGE SHIFT buttons

PICTURE MODE button

IRIS button

FREEZE button

Selecting the Picture Mode

Note

• For details on Iris, see page 45.

Freezing a Moving Image

Press hFREEZE.

• The projected image is frozen.

Press hFREEZE again to return

to the moving image from the currently connected device.

EIP-1600T_EN_i 06.1.24, 1:06 PM38

You can select the appropriate picture mode to best match the projected image you are watching.

Press kPICTURE MODE.

• When pressing kPICTURE MODE, the picture

mode changes in the following order:

Standard Dynamic

Note

• See page 43 for details on the picture mode.

Natural

Movie2 Movie1Memory

Menu Items

The following shows the items that can be set in the projector. The selectable items vary depending on the selected input, input signals, or adjustment values. Items that cannot be selected will be greyed out.

“Picture” menu

PAGE 1

Picture INPUT 1

Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue

SEL./ADJ. RETURN

0 0 0 0 0 0

Standard

ENTER END

Main menu Sub menu

Picture

Picture Mode

Page 43 Page 43

Contrast

Bright

Color

Tint

Sharp

Red

Blue

Standard Natural Dynamic Movie1 Movie2 Memory

+30-30

Page 43

PAGE 2

Picture INPUT 1

Picture Mode

CLR Temp

BrilliantColor™ C. M. S. Progressive DNR IRIS Lamp Setting

Reset

SEL./ADJ. RETURN

K7500

Single ADJ END

Standard

3D Progressive Level 1 High Brightness Bright

“C.M.S.”

C. M. S.

C. M. S. - Hue

C. M. S. - Saturation C. M. S. - Value

Reset

SEL./ADJ. RETURN

*1 When the Progressive mode is set to “3D Progressive” or

“Film Mode”, the C.M.S. function cannot be used.

*2 Item that cannot be set when inputting an RGB signal

through INPUT 5 or INPUT 6.

R Y G C B M

Reset

0 0 0 0 0 0

ENTER END

CLR Temp

Page 44

BrilliantColor™ [0/1/2]

5500K 6500K 7500K 8500K 9300K 10500K

Page 43

C.M.S.

Page 44

Progressive

Page 44

DNR OFF

Page 45

IRIS High Brightness

Page 45

Lamp Setting

Page 45

Reset

C.M.S.-Hue

Page 44

C.M.S.-Saturation

Page 44

C.M.S.-Value

Page 44

Reset

2D Progressive 3D Progressive Film Mode

Level 1 Level 2 Level 3

Medium Mode High Contrast

Bright Eco + Quiet

+30-30

EIP-1600T_EN_i 06.1.24, 1:06 PM39

Menu Items (Continued)

“Fine Sync” menu

Fine Sync INPUT 5

Clock Phase H-Pos V-Pos

Reset Special Modes Auto Sync

Cur. sig. freq : H 33.8 kHz / V 60 Hz

SEL./ADJ.

RETURN

0 0 0 0

1080I On

ENTER END

• The “Fine Sync” menu is not available for INPUT 3 or INPUT 4.

“Options1” menu

Options 1 INPUT 1

Image Shift Overscan H Overscan V Subtitle OSD Display Video System Signal Type HDMI Setting Background Auto Power Off

SEL./ADJ. RETURN

*1 Item that can be set when using INPUT 3 or

INPUT 4.

*2 Item that can be set when using IINPUT 5 or

INPUT 6.

0 0 0 0

ENTER END

On Auto Auto Standard Blue On h0Lamp Timer(Life) 100%

“Options2” menu

Options 2 INPUT 1

PRJ Mode RS-232C STANDBY Mode Fan Mode

All reset

Language

SEL./ADJ. RETURN

Front 9600 bps Eco Normal

English

ENTER END

Main menu Sub menu

Fine Sync

Clock

+150-150

Page 46 Page 46

Phase

+30-30

Page 46

H-Pos

+150-150

Page 46

V-Pos

Page 46

Reset

Special Modes 1035I

Page 46

Auto Sync [On/Off]

+60-60

1080I

Page 46

Cur. sig. freq

Main menu Sub menu

Options 1

Page 47

Page 46

Image Shift

Page 47

Overscan H Overscan V

+24-24

+30-30 +30-30

Page 47

Subtitle

+30-30

Page 47

OSD Display [On/Off]

Page 48

Video System

Page 48

Signal Type

Page 48

HDMI Setting

Page 48

Background

Page 48

Auto Power Off [On/Off]

Auto PAL SECAM NTSC 4.43

Auto RGB Component

Standard Enhanced

Blue None

Page 49

Lamp Timer(Life)

Main menu Sub menu

Options2

Page 49

PRJ Mode

Page 49

RS-232C

Page 50

STANDBY Mode

Page 50

Fan Mode

Page 50

All reset

Front Ceiling + Front Rear Ceiling + Rear

9600bps 115200bps

Standard Eco

Normal High

Page 50

Language

Page 50

English Deutsch Español Nederlands Français Italiano

NTSC 3.58 PAL-M PAL-N PAL-60

Svenska Português

EIP-1600T_EN_i 06.1.24, 1:06 PM40

Using the Menu Screen

ENTER button

Adjustment buttons (P/R/O/Q)

MENU button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press dMENU.

• The “Picture” menu screen for the selected input mode is displayed.

Press Q or O to select the menu

icon to adjust.

• The selected icon is highlighted.

Menu icon Menu screen

Picture

Fine Sync

Options1

Options2

Example: “Picture” screen menu for INPUT 1 mode

Menu icons

Picture INPUT 1

Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue

Adjustment buttons (P/R/O/Q)

MENU button

ENTER button

RETURN button

• Press eRETURN to re-

turn to the previous screen when the menu is displayed.

Selected input mode

Standard

0 0 0 0 0 0

Note

• The “Fine Sync” menu is not available for INPUT 3 or INPUT 4.

EIP-1600T_EN_i 06.1.24, 1:06 PM41

SEL./ADJ. RETURN

ENTER END

Using the Menu Screen (Continued)

Press P or R to select the item to

adjust.

• The selected item is highlighted.

To adjust the projected image while watching it

Press iENTER.

• The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen.

• When pressing P or R, the following item (“Color” after “Bright”) will be displayed.

Note

• Press iENTER again to return to the

previous screen.

Picture INPUT 1

Picture Mode Contrast 0

Bright

Color Tint Sharp Red Blue

SEL./ADJ. RETURN

Standard

0 0 0 0 0

Single ADJ END

Items to be adjusted

The item displayed by itself

Picture INPUT 1

SEL./ADJ. RETURN

0Bright

Rtn. Menu END

Press O or Q to adjust the item

selected.

• The adjustment is stored.

Press dMENU.

• The menu screen will disappear.

Picture INPUT 1

Picture Mode Contrast 0

Bright

Color Tint Sharp Red Blue

SEL./ADJ. RETURN

Standard

0 0 0 0 0

Single ADJ END

Note

• The d MENU button does not function while the projector is operating the “Auto Sync” or “FREEZE”

functions.

EIP-1600T_EN_i 06.1.24, 1:06 PM42

Picture Adjustment (“Picture” menu)

Menu operation n Page 41

Q PAGE 2Q PAGE 1

Picture INPUT 1

Picture Mode Contrast 0 Bright Color Tint Sharp Red Blue

1 1

1 Selecting the Picture Mode

1 1

Standard

0 0 0 0 0 0

Picture INPUT 1

Picture Mode

CLR Temp

BrilliantColor™ C. M. S. Progressive DNR IRIS Lamp Setting

Reset

K7500

Standard

3D Progressive Level 1 High Brightness Bright

Selectable

items

Standard

Natural

Dynamic

Movie1

Movie2

Memory

Description

For standard image

A balanced color image is obtained.

A vivid image is obtained.

Makes the black levels of the dark portions of the screen more pronounced and vivid.

Reduces glare and creates a subdued tone.

Allows you to store your picture adjustment settings. The settings

The default settings of each item when selecting Picture Mode

CLR Temp

7500K

6500K

7500K

BrilliantColor™

IRIS

High Brightness

Medium Mode

High Brightness

Lamp Setting

Bright

Eco + Quiet

Bright

stored effect each input mode.

•

You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.

Note

• You can also press k PICTURE MODE on the remote control to select the picture mode.

(See page 38.)

2 Adjusting the Image

Adjustment items

Contrast

Bright

Color*

Tint*

Sharp*

Red

Blue

BrilliantColor™*

*1Item that cannot be adjusted in RGB mode.

BrilliantColor™ uses Texas Instruments' BrilliantColor™ technology. As the BrilliantColor™ level is increased,

For less contrast.

For less brightness.

For less color intensity.

For making skin tones purplish.

For less sharpness.

For weaker red.

For weaker blue.

For making the effect weaker.

O button

For more contrast.

For more brightness.

For more color intensity.

For making skin tones greenish.

For more sharpness.

For stronger red.

For stronger blue.

For making the effect stronger.

Q button

the image becomes brighter while the color reproduction is kept at a high level.

Note

• To reset all adjustment items, select “Reset” and press iENTER. The Picture Mode

settings of the selected input return to the default settings.

EIP-1600T_EN_j 06.1.24, 1:07 PM43

Picture Adjustment (“Picture” menu) (Continued)

3 Adjusting the Color

Temperature

Selectable

items

5500K 6500K 7500K 8500K 9300K 10500K

• Values on “CLR Temp” are only for general standard purposes.

4 Adjusting the Colors

For lower color temperature for warmer, reddish incandescent-like images.

For higher color temperature for cooler, bluish, fluorescent-like images.

Note

Select “C.M.S.” (Color Management System) in the “Picture” menu and then press i ENTER.

This function adjusts each of the six main colors that comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.

Selectable items

C.M.S.-Hue

C.M.S.-Saturation

C.M.S.-Value

Reset

Adjusting “Hue”, “Saturation”, or “Value”.

1Press P or R to select either “Hue”, “Saturation”, or

“Value” and then press i ENTER.

2Select the color to be adjusted with P or R and

adjust it with O or Q.

Example of adjusting the “Hue”

Main colors R (Red) Y (Yellow) G (Green) C (Cyan) B (Blue) M (

Magenta

O button Closer to magenta Closer to red Closer to yellow Closer to green Closer to cyan Closer to blue

)

Description

P R

Description

Sets the hue of the main colors.

Sets the saturation of the main colors

Sets the brightness of the main colors.

The adjustments of “Hue”, “Saturation” and “Value” of all colors are reset to the default setting.

Q button Closer to yellow Closer to green Closer to cyan Closer to blue Closer to magenta Closer to red

• When “Saturation” is selected, the selected color becomes O: lighter. Q: thicker.

• When “Value” is selected, the selected color becomes O: darker. Q: brighter.

• To reset the adjustment values of each color to the default settings, select “Reset” and press i ENTER.

Info

• When the Progressive mode is set to “3D Progressive” or “Film Mode”, the C.M.S. function cannot be used.

5 Progressive

Selectable

items

2D Progressive

3D Progressive

Film Mode

* The film source is a digital video recording with the

original encoded as is at 24 frames/second. The projector can convert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.

• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the three-two pull down enhancement will be enabled automatically when the film source has been entered.

• When the image is blurred or noisy, switch to the optimal mode.

• When using progressive inputs, inputs are directly displayed so that 2D Progressive, 3D Progressive and Film Mode cannot be selected.

Useful to display fast-moving images such as sports.

Useful to display relatively slowmoving images such as drama and documentary more clearly.

Reproduces the image of film source* clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhancement to progressive mode images.

Note

Info

• The settings can be made either when INPUT3 or INPUT4 are selected or when INPUT1, 2, INPUT5, or INPUT6 are selected and the input signal is 480I, 576I, or 1080I.

Menu operation n Page 41

Description

EIP-1600T_EN_j 06.1.24, 1:07 PM44

Menu operation n Page 41

6 Reducing Image Noise

(DNR)

Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.

Selectable items

OFF

Level 1-3

Note

Set “DNR” to “OFF” in the following cases:

• When the image is blurry.

• When the contours and colors of moving images drag.

• When TV broadcasts with weak signals are projected.

DNR does not function.

Sets the DNR level for viewing a clearer picture.

Info

• This function is available for 480I, 480P, 576I, and 576P signals using INPUT 1, 2, 5 or 6.

Description

7 Switching the Iris

Setting

This function controls the quantity of the projected light and the contrast of the image.

Selectable items

High Brightness

Medium Mode

High Contrast

Note

• You can also use l IRIS on the remote con-

trol to change the Iris. (See page 38.)

8 Lamp Setting

Select-

Bright-

able

ness

items

Eco +

Approx.

Quiet

87%

100%

Bright

High brightness is given priority over high contrast.

Intermediate mode between high contrast and high brightness.

High contrast is given priority over high brightness.

Fan

sound

Low

Normal

Description

Power consumption (When using

AC 100V)

310W

355W

Lamp Life

Approx.

3,000 hours

Approx.

2,000 hours

EIP-1600T_EN_j 06.1.24, 1:07 PM45

Note

• When “Lamp Setting” is set to “Eco+Quiet”, the power consumption will decrease and the lamp life will extend. (Projection brightness decreases approximately 13%.)

Computer Image Adjustment (“Fine Sync” menu)

Fine Sync INPUT 5

Clock Phase H-Pos V-Pos

Reset Special Modes Auto Sync

Cur. sig. freq : H 33.8 kHz / V 60 Hz

1 Adjusting the

0 0 0 0

1080I On

Computer Image

Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.

Selectable items

Clock

Phase

H-Pos

V-P os

Note

• You can automatically adjust the computer image by setting “Auto Sync” in the “Fine Sync” menu to “On” or pressing f AUTO SYNC on the remote control.

• “Clock”, “Phase”, “H-Pos” and “V-Pos” cannot be adjusted when INPUT 6 is selected.

• The adjustable area of each item may be changed according to the input signal.

• To reset all adjustment items, select “Reset” and press i ENTER.

Adjusts vertical noise.

Adjusts horizontal noise (similar to tracking on your VCR).

Centers the on-screen image by moving it to the left or right.

Centers the on-screen image by moving it up or down.

Description

2 Special Modes Setting

Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in “Special Modes” in the “Fine Sync” menu may need to be selected to match the computer display mode.

Note

• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)

• Information on the currently selected input signal can be confirmed in item 4.

3 Auto Sync (Auto Sync

Selectable items

Off

Note

• Auto Sync adjustment is also performed by pressing f AUTO SYNC on the remote control.

• The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

• When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments.

Menu operation n Page 41

Adjustment)

Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer.

Auto Sync adjustment is not automatically performed.

Description

EIP-1600T_EN_j 06.1.24, 1:07 PM46

4 Checking the Input

Signal

This function allows you to check the current input signal information.

Using the “Options” Menu

Options 1 INPUT 1

Image Shift

Overscan H

Overscan V

Subtitle

OSD Display

Video System

Signal Type

HDMI Setting

Background

Auto Power Off

9 0

Settings on the Options 1 menu

0 0 0 0

On Auto Auto Standard Blue On h0Lamp Timer(Life) 100%

Menu operation n Page 41

Adjusting the Overscan

This function allows you to adjust the Overscan area ratio (display area ratio).

Orientation

Overscan H (Horizontal)

Overscan V (Vertical)

O button

Reduces the image. (The display area ratio becomes larger.)

Q button

Enlarges the image. (The display area ratio becomes smaller.)

1 Adjusting the Image

Position

You can move the projected image vertically.

O button

Note

• The Image Shift function cannot be selected when “Resize” is set to “DOT BY DOT”.

• You can also use the IMAGE SHIFT buttons on the remote control to adjust the image position.

Q button

Note

• This function can only be adjusted when a video, S-video, or Component signal is input.

• If the display area ratio is set too large, noise may appear at the screen edges. If this happens, set the display area ratio to a smaller value.

• The adjustment area changes according to the input signal when “Resize” is set to “CINEMA ZOOM”.

• Also read “About Copyrights” on page 37.

Adjusting the Vertical Size of

the Display (Subtitle Setting)

With this function, you can adjust the vertical size of the display to allow for subtitles.

O button

Q button

•

When changing the screen with the Subtitle setting, not only the bottom of the screen rises, but also the upper part is changed to a certain point.

• The Subtitle setting can be adjusted more effectively with the Overscan and Image Shift functions.

• The Subtitle setting only works when “Resize” is set to “CINEMA ZOOM”.

• The adjustment area changes according to the input signal.

The image is compressed by adjusting the vertical size of the display.

The image is enlarged by adjusting the vertical size of the display.

Note

EIP-1600T_EN_j 06.1.24, 1:07 PM47

Using the “Options” Menu (Continued)

Menu operation n Page 41

Setting On-screen Display

Selectable

items

Off

All On-screen Displays are displayed.

INPUT/FREEZE/AUTO SYNC/RESIZE/ PICTURE MODE are not displayed.

Setting the Video

Description

System

This function can only be set in INPUT 3 or INPUT 4.

The video input system mode is factory preset to “Auto”;however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal.

Selectable items

PA L

SECAM

NTSC4.43

NTSC3.58

When connected to PAL video equipment.

When connected to SECAM video equipment.

When reproducing NTSC signals in PAL video equipment.

When connected to NTSC video equipment.

Description

6 Signal Type Setting

This function allows you to select the input signal type (RGB or Component) for INPUT 5 or INPUT 6.

Selectable items

Auto

RGB

Component

Note

• You can also select “Signal Type” using g RGB/COMP. on the remote control (INPUT 5 or INPUT 6).

Selecting the HDMI Setting

When there is an HDMI-capable device connected to INPUT 6, an optimum picture may not be displayed if the device’s output signal type and the projector’s input signal type do not match. If this should occur, switch the HDMI Setting.

Selectable items

Standard

Enhanced

Automatically selects the appropriate input signal between RGB and Component.

Set when RGB signals are received.

Set when component signals are received.

When the black levels of the image show banding or appear faded, select the option that results in the best picture quality. (In most circumstances, “Standard” should be selected.)

Description

EIP-1600T_EN_k 06.1.24, 1:08 PM48

Note

• The HDMI Setting can be selected only when INPUT 6 is selected.

Selecting the Background

Image

Selectable items

Blue

None

Blue screen

— (Black screen)

Description

9 Auto Power Off

Function

Selectable

items

Off

When no input signal is detected for more than 15 minutes, the projector will automatically enter standby mode.

The Auto Power Off function will be disabled.

Description

Menu operation n Page 41

Options 2 INPUT 1

PRJ Mode

RS-232C

STANDBY Mode

Fan Mode

All reset

Language

Settings on the Options 2 menu

Front 9600 bps Eco Normal

English

Note

• When the Auto Power Off function is set to “On”, 5 minutes before the projector enters standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

0 Checking the Lamp Life

Status

You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).

Lamp usage condition

“Life”

Operated exclusively with Lamp Setting set to “Eco + Quiet”

Operated exclusively with Lamp Setting set to “Bright”

Note

• It is recommended that the lamp be changed when the remaining lamp life becomes 5%.

• The lamp life may vary depending on the usage condition.

Remaining lamp life

100%

Approx. 3,000 hours

Approx. 2,000 hours

Approx. 150 hours

Approx. 100 hours

1 Reversing/Inverting

Projected Images

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

See page 19 for details of Projection (PRJ) Mode.

Normal image (Projected from the front of the screen)

Inverted image (Projected from the front of the screen with an inverted projector)

Reversed image (Projected from the rear of the screen or with a mirror)

Reversed and inverted image (Projected with a mirror)

Description

EIP-1600T_EN_k 06.1.24, 1:08 PM49

Using the “Options” Menu (Continued)

Menu operation n Page 41

Selecting the Transmission

Speed (RS-232C)

Make sure that both the projector and computer are set for the same baud rate.

Selectable

items

9600bps

Transmission speed is slow.

Description

P R

115200bps

Transmission speed is rapid.

Reducing the Power Consumption When the Power Is in Standby Mode

When “STANDBY Mode” has been set to “Standard”, the RS-232C function is activated and power is consumed even in standby mode. It is recommended that “STANDBY Mode” be set to “Eco” when it is not being used. This reduces power consumption when the projector is in standby mode.

Selectable items

Standard

Eco

Note

• When you want to control the projector using the RS-232C function, set to “Standard”.

The RS-232C function is activated even if the projector is in standby mode.

The RS-232C function is switched off when the projector is in standby mode.

Description

4 Fan Mode Setting

This function changes the fan rotation speed.

Selectable

items

Normal

High

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

Suitable for normal environments.

Select this when using the projector at altitudes of approximately 4,900 feet (1,500 meters) or more.

Returning to the Default

Description

Settings

Use “All reset” to initialize all the adjustments you have made to the default settings.

Note

The following items cannot be initialized.

• “Fine Sync” menu – Special Modes

• “Options1” menu – Lamp Timer (Life) – Language

Selecting the On-screen

Display Language

The projector can switch the on-screen display language among 11 languages.

English Deutsch Español Nederlands Français Italiano

Svenska Português

EIP-1600T_EN_k 06.1.24, 1:08 PM50

Maintenance

Cleaning the projector

■ Ensure that you have unplugged the power cord before cleaning the projector.

■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.

■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in

a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.

Mild detergent

Mild detergent diluted

with water

Cleaning the lens

■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.

■ As the surface of the lens can easily get damaged, be sure not to scrape or hit the lens.

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.

Thinner

Wax

EIP-1600T_EN_l 06.1.24, 1:08 PM51

Info

• If you want to clean the air vents during pro-

jector operation, be sure to press o STANDBY-ON on the projector or aSTANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, clean the vents.

Maintenance Indicators

■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector.

■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.

Top View

Temperature warning indicator

Lamp indicator

Power indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projector will enter standby mode. After “ ” appears, be sure to perform the measures described on page

53.

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter standby mode. At this time, the lamp indicator will illuminate in red.

■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

Indicators on the Projector

Power indicator

Lamp indicator

Temperature warning indicator

Green on Normal (Standby)

Red on

Green blinks

Red blinks Green on

Green blinks

Red on The lamp is shut down abnormally or

Off

Red on

Normal (Power on)

Abnormal (See page 53.)

Normal (Cooling) Normal

The lamp is warming up or shutting down.

requires to be changed. (See page 53.)

Normal

The internal temperature is abnormally high. (See page 53.)

EIP-1600T_EN_l 06.1.24, 1:08 PM52

Maintenance indicator

Tempera-

ture

warning

indicator

Lamp

indicator

Power

indicator

Green on

when the

warming

Green on/

(Cooling)

Normal

Off

(Green

blinks

lamp is

up or

turning

off.)

Red on

Red

blinks

Abnormal

Red on

(Standby)

Red on

(Standby)

Green blinks

Problem

The internal temperature is abnormally high.

The lamp does not illuminate.

Time to change the lamp.

The lamp does not illuminate.

The power indicator blinks in green when the projector is on.

Cause

• Blocked air intake

• Cooling fan breakdown

• Internal circuit failure

• Clogged air intake

• The lamp is shut down abnormally.

• Remaining lamp life becomes 5% or less.

• Burnt-out lamp

• Lamp circuit failure

• The lamp unit cover is open.

Possible Solution

• Relocate the projector to an area with proper ventilation. (see page 8)

• Take the projector to your nearest EIKI Authorized Dealer or Service Center for repair.

• Disconnect the power cord from the AC outlet, and then connect it again.

• Carefully replace the lamp. (See page 55.)

• Take the projector to your nearest EIKI Authorized Dealer or Service Center for repair.

• Please exercise care when replacing the lamp.

• Securely install the cover.

• If the power indicator blinks in green even when the lamp unit cover is securely installed, contact your nearest EIKI Authorized Dealer or Service Center for advice.

Info

• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

• If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

• Do not unplug the power cord after the projector has entered standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.

EIP-1600T_EN_l 06.1.24, 1:08 PM53

Regarding the Lamp

Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (see page 49)

■ Purchase a replacement lamp of type AH-11201 from your place of purchase, nearest EIKI Authorized Dealer or Service Center.

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest EIKI Authorized Dealer or Service Center to assure safe operation.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

Replacing the Lamp

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury.

■ Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center.

* If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized

Dealer or Service Center for repair.

EIP-1600T_EN_l 06.1.24, 1:08 PM54

Removing and Installing the Lamp Unit

Warning!

• The lamp unit becomes very hot while the projector is operating. Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Info

• Make sure that you remove the lamp unit by

the handle. Do not touch the glass surface of the lamp unit or the inside of the projector.

• To avoid injury to yourself and damage to the

lamp, be sure to carefully follow the steps below.

• Do not loosen other screws except for the

lamp unit cover and lamp unit.

Press oSTANDBY-ON on the pro-

jector or aSTANDBY on the remote control to put the projector into standby mode.

• Wait until the cooling fan stops.

Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down (about 1 hour).

Optional

accessory

STANDBY-ON button

AC socket

Lamp unit AH-11201

Remove the lamp unit cover.

• Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

EIP-1600T_EN_l 06.1.24, 1:08 PM55

User service screw (for lamp unit cover)

Regarding the Lamp (Continued)

Remove the lamp unit.

• Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

Insert the new lamp unit.

• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

Replace the lamp unit cover.

• Align the tab on the lamp unit cover (1) and place it while pressing the tab (2) to close it. Then tighten the user service screw to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Handle

Securing screws

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Connect the power cord.

• Plug the power cord into the AC socket of the projector.

Reset the lamp timer.

• While simultaneously holding down rMENU, pENTER and R on the projector, press oSTANDBY-ON on the projector.

• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.

EIP-1600T_EN_l 06.1.24, 1:09 PM56

AC socket

STANDBY-ON button

ENTER button

MENU button

R button

Connecting Pin Assignments

COMPUTER-RGB/COMPONENT INPUT5 Terminal: 15-pin Mini D-sub female connector

COMPUTER-RGB Input

1. Video input (red)

2. Video input (green/sync on green)

RS-232C Terminal: 9-pin Mini DIN female connector

RS-232C Terminal: 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor

RS-232C Cable recommended connection: 9-pin D-sub female connector

3. Video input (blue)

4. Not connected

5. Not connected

6. Earth (red)

7. Earth (green/sync on green)

8. Earth (blue)

9. Not connected

10. GND

11. Not connected

12. Bi-directional data

13. Horizontal sync signal: TTL level

14. Vertical sync signal: TTL level

15. Data clock

Pin No.

Signal Name

Signal NamePin No.

SignalPin No.

RD SD

RS CS

RD SD

RS CS

CD RD SD ER SG DR RS CS CI

Receive Data Send Data

Signal Ground

Request to Send Clear to Send

Receive Data Send Data

Signal Ground

Request to Send Clear to Send

I/O Reference

Input Output

I/O Reference

Input Output

Component Input

1. PR (CR)

2. Y

B (CB)

3. P

4. Not connected

5. Not connected

6. Earth (P

7. Earth (Y)

8. Earth (P

9. Not connected

10. Not connected

11. Not connected

12. Not connected

13. Not connected

14. Not connected

15. Not connected

Not connected Connected to internal circuit Connected to internal circuit Not connected Connected to internal circuit Not connected Connected to CS in internal circuit Connected to RS in internal circuit Not connected

SignalPin No.

CD RD SD ER SG DR RS CS CI

Note

• Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. computer).

EIP-1600T_EN_l 06.1.24, 1:09 PM57

Projector

Pin No.

4 5 6

Computer

Pin No.

4 5 6

Connecting Pin Assignments (Continued)

HDMI Terminal

119

218

NamePin No.

TMDS Data2+

TMDS Data2 Shield

TMDS Data2-

TMDS Data1+

TMDS Data1 Shield

TMDS Data1-

TMDS Data0+

NamePin No.

TMDS Data0 Shield

8. TMDS Data0-

9. TMDS Clock+

10. TMDS Clock Shield

11. TMDS Clock-

12. CEC

13.

NamePin No.

Reserved

14. SCL

15. SDA

16. DDC/CEC Ground

17. +5V Power

18. Hot Plug Detect

19.

RS-232C Specifications and Command Settings

Computer control

A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type, sold separately) to the projector. (See page 27 for connection.)

Communication conditions

Set the serial port settings of the computer to match that of the table. Signal format: Conforms to RS-232C standard. Parity bit: None Baud rate: * 9,600 bps/115,200 bps Stop bit: 1 bit Data length: 8 bits Flow control: None * Set the projector's baud rate to the same rate as used by the computer.

Basic format

Commands from the computer are sent in the following order: command, parameter, and return code. After the projector processes the command from the computer, it sends a response code to the computer.

Command format

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digit Parameter 4-digit

Response code format

Normal response

Return code (0DH)

Problem response (communication error or incorrect command)

Return code (0DH)

ERR

Return code (0DH)

Info

• When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands.

• When more than one code is being sent, send each command only after the response code for the previous command from the projector is verified.

Commands

Example: When turning on the

projector, make the following setting.

CONTROL CONTENTS Power Off Power On INPUT 1 (Video1 : Component1) INPUT 2 (Video2 : Component2) INPUT 3 (Video3 : S-Video) INPUT 4 (Video4 : Video)

(RGB1 : RGB/Component)

INPUT 5 INPUT 6

(RGB2 : RGB/Component)

COMMAND PARAMETER

EIP-1600T_EN_l 06.1.24, 1:09 PM58

POWR _1__

RETURN

OK or ERR

Note

• If an underbar (_) appears in the parameter column, enter a space.

→ ←

ProjectorComputer

Computer Compatibility Chart

Computer

• Multiple signal support Horizontal Frequency: 15-70 kHz, Vertical Frequency: 45-85 Hz, Pixel Clock: 12-85 MHz Sync signal: Compatible with TTL level

The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.

PC/MAC

MAC 13" MAC 16" MAC 19"

VGA

SVGA

XGA

—

VGA

SVGA

XGA

Resolution

640 × 350

640 × 400

720 × 350

720 × 400

640 × 480

800 × 600

1,024 × 768

1,280 × 720 1,280 × 768

640 × 480 800 × 600 832 × 624

1,024 × 768

Horizontal Frequency

(kHz)

27.0

31.5

37.5

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.4

35.1

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

45.0

47.8

34.9

37.8

49.7

60.2

• Compatible with sync on green signal

• Expansion System resizing technology

Vertical Frequency

(Hz)

60 70 85 60 70 85 60 70 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 60 60 67 60 75 75

VESA

Standard

✔

✔ ✔ ✔

✔ ✔

✔ ✔ ✔

HDMI

Support

✔

Display

Upscale

True

Note

• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.

DTV

Signal

480I

480P

540P

576I

576P

720P

1035I

1080I

EIP-1600T_EN_l 06.1.24, 1:09 PM59

Horizontal Frequency (kHz)

15.7

31.5

33.8

15.6

31.3

45.0

28.1

33.8

28.1

33.8

Vertical Frequency (Hz)

HDMI Support

✓

Troubleshooting

Problem Check

• Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• Cables incorrectly connected to the projector.

• Remote control battery has run out.

Picure does not appear

or projector does not

start.

No picture appears (or

picture is dark).

Color is faded or poor.

Picture is blurred;

noise appears.

Picture is green on INPUT 5 (Component)/ INPUT 6 (Component).

Picture is pink (no green)

on INPUT 5 (RGB)/INPUT

6 (RGB).

An unusual sound is

occasionally heard from

the cabinet.

Maintenance indicator on

the projector illuminates.

• External output has not been set when connecting notebook computer.

• The lamp unit cover is not installed correctly.

• Cables incorrectly connected to the projector.

• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not be projected unless the signal output setting of the computer is switched to the external output. Refer to the owner’s manual of the computer for how to switch its signal output settings.

• Image adjustments are incorrectly set.

• Make adjustments to “Color”, “Tint” and “BrilliantColor™” in “Picture Mode”.

(Video Input only)

• Video input system is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

• There is fog on the lens. If the projector is carried from a cold room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Please set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

• Perform “Fine Sync” Adjustments (“Clock” Adjustment)

• Perform “Fine Sync” Adjustments (“Phase” Adjustment)

• Noise may appear depending on the computer.

• Select “Signal Type” in the “Options1” menu and change the input

signal type.

• If the picture is normal, the sound is due to cabinet shrinkage

caused by room temperature changes. This will not affect operation or performance.

• See “Maintenance Indicators”.

Page

–

23–27

55, 56

23–27

–

EIP-1600T_EN_l 06.1.24, 1:09 PM60

Problem

Picture is too bright and

whitish.

The black levels of the

image show banding or

appear faded when

INPUT 6 is selected.

The cooling fan becomes

The lamp suddenly turns

This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.

noisy.

The lamp does not light

up even after the

projector turns on.

off during projection.

The image sometimes

flickers.

The lamp needs much

time to turn on.

Picture is dark.

The remote control

cannot be used.

• Image adjustments are incorrectly set.

• Select the HDMI Setting (“Standard” or “Enhanced”) that results in

the best picture quality.

• When temperature inside the projector increases, the cooling fan

runs faster.

• The lamp indicator is illuminating in red.

Replace the lamp.

• Cables incorrectly connected to the projector or the connected

equipment works improperly.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.

While the remaining lamp life draws to a close, replace the lamp.

• Operate the remote control while pointing it at the projector’s remote

control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent light is shining on the

projector’s remote control sensor, place the projector where it will not be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the

batteries are inserted correctly or insert new ones.

Check

Page

–

52, 55

23-27

EIP-1600T_EN_l 06.1.24, 1:09 PM61

Specifications

Product type

Model

Video system

Display method

DMD panel

Projection lamp

Component input signal

S-video input signal

Video input signal

Computer RGB/

Component input signal

HDMI input signal

Horizontal resolution

Vertical frequency

Horizontal frequency

RS-232C terminal

TRIGGER terminal

Rated voltage

Rated frequency

Power consumption

Power consumption (standby)

Heat dissipation

Operating temperature

Storage temperature

I/R carrier frequency

Dimensions (approx.)

Weight (approx.)

Replacement parts

Lens

(INPUT1/2)

(INPUT 3)

(INPUT 4)

(INPUT 5)

(INPUT 6)

Pixel clock

Input current

Cabinet

Projector EIP-1600T NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/ DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50 Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments Panel size: 0.65", 1chip DMD Drive method: Digital Light Processing (DLP™) No. of dots: 983,040 dots (1280 [H] × 768 [V]) 1–1.15 × zoom lens, F2.4–2.6, f = 19.0–21.9 mm 275 W DC lamp RCA connector Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB (CB): 0.7 Vp-p, 75 Ω terminated PR (CR): 0.7 Vp-p, 75 Ω terminated 4-pin mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω terminated 15-pin mini D-sub connector RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above HDMI terminal (video signal only)

720 TV lines (DTV720P) 45–85 Hz 15–70 kHz 12–85 MHz 9-pin mini DIN connector Power jack: DC 12V output AC 100–240 V

3.7 A 50/60 Hz 355 W (Lamp Setting “Bright”)/ 310 W (Lamp Setting “Eco + Quiet”) 340 W (Lamp Setting “Bright”)/ 300 W (Lamp Setting “Eco + Quiet”) 4 W (AC 100 V) – 5 W (AC 240 V)* 1,335 BTU/hour (Lamp Setting “Bright”)/ 1,165 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 100 V 1,280 BTU/hour (Lamp Setting “Bright”)/ 1,130 BTU/hour (Lamp Setting “Eco + Quiet”) with AC 240 V 41°F to 95°F (+5°C to +35°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 12 13/32" × 4 19/64" × 11 1/32" (315 (W) × 109 (H) × 280 (D) mm) (main body only) 12 13/32" × 4 47/64" × 11 37/64" (315 (W) × 120 (H) × 294 (D) mm) (including adjustment foot and projecting parts)

8.8 lbs. (4.0 kg) Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe, except U.K., Video cable, DIN-D-sub RS-232C adaptor, Quick Guide, Owner’s manual

with AC 100 V

with AC 240 V

*1 When STANDBY Mode is set to “Eco”

As a part of policy of continuous improvement, EIKI reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

EIP-1600T_EN_m 06.1.24, 1:09 PM62

Dimensions

Units: inches (mm)

28095

4773

105

109

EIP-1600T_EN_m 06.1.24, 1:09 PM63

315

33.8

77.5

65.546.2

47.5 104

Index

AC socket ....................................................... 28

Accessories ................................................... 10

Adjustment buttons ........................................ 41

Aspect ratio .................................................... 36

Auto Power Off............................................... 49

Auto Sync

(Auto Sync adjustment) .............................. 46

AUTO SYNC button ....................................... 46

Background.................................................... 48

Backlight button .............................................13

Blue ................................................................ 43

Bright ............................................................. 43

BrilliantColor™............................................... 43

Checking the Input Signal ............................. 46

CINEMA ZOOM ...................................... 36, 37

Clock ..............................................................46

CLR Temp (Color Temperature) .................... 44

C.M.S. ............................................................44

Color .............................................................. 43

Contrast ......................................................... 43

DOT BY DOT .................................................37

DNR ............................................................... 45

ENTER button................................................ 41

Exhaust vent ........................................... 12, 51

Fan Mode ....................................................... 50

Fine Sync .......................................................46

Focus ring ......................................................30

FREEZE button .............................................38

GEOMETRIC ADJUSTMENT ....................... 34

H & V KEYSTONE ......................................... 35

HDMI Setting ................................................. 48

H-Pos .............................................................46

HEIGHT ADJUST lever .................................30

Hue ................................................................44

Image Shift .................................................... 47

IMAGE SHIFT buttons ................................... 38

INPUT 1 terminal ...........................................23

INPUT 1 – 6 modes .......................................29

INPUT 2 terminal ...........................................23

INPUT 3 terminal ...........................................24

INPUT 4 terminal ...........................................24

INPUT 5 terminal .................................... 25, 26

INPUT 6 terminal ...........................................25

INPUT buttons ...............................................29

Intake vent ........................................ 11, 12, 51

IRIS button .....................................................38

Kensington Security

Standard connector ............................. 12, 13

KEYSTONE button ........................................32

Keystone Correction ......................................32

Lamp ....................................................... 10, 54

Lamp indicator ...............................................52

Lamp Setting .................................................45

Lamp Timer (Life) .......................................... 49

Lamp unit .......................................................55

Language (on-screen display language) ...... 50

Lens cap ........................................................ 11

MENU button ................................................ 41

ON button ...................................................... 28

Optional accessories .....................................10

OSD Display ..................................................48

Overscan ....................................................... 47

Phase ............................................................. 46

Picture Adjustment ........................................ 43

Picture Mode .......................................... 38, 43

PICTURE MODE button ................................38

Picture (Screen) Size and Projection Distance .......

Power cord ..................................................... 28

PRJ Mode ............................................... 19, 49

Progressive ....................................................44

R-03 batteries ................................................14

Rear adjustment foot .....................................31

Red ................................................................43

Remote control .............................................. 13

Remote control sensor ..................................15

Replacing the lamp ................................. 54, 55

Resize ..................................................... 36, 37

RESIZE button ............................................... 36

RETURN button ............................................. 41

RGB/COMP. button........................................ 48

RS-232C Setting............................................ 50

RS-232C terminal ..........................................27

Saturation ...................................................... 44

Sharp .............................................................43

SIDE BAR ............................................... 36, 37

Special Modes ...............................................46

STANDBY button ........................................... 29

STANDBY-ON button .............................. 28, 29

STANDBY Mode ............................................ 50

STRETCH ............................................... 36, 37

Subtitle ...........................................................47

Supplied accessories .................................... 10

Temperature warning indicator ......................52

Tint .................................................................43

TRIGGER terminal ........................................ 12

Value ..............................................................44

Video System ................................................48

V-Pos ..............................................................46

Zoom ring ....................................................... 30

EIP-1600T_EN_m 06.1.24, 1:09 PM64

A-Key to better communications

U.S.A.

EIKI International, Inc. 30251 Esperanza Rancho Santa Margarita CA 92688-2132 U.S.A. Tel : 800-242-3454 (949)-457-0200 Fax: 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com

Deutschland & Österreich

EIKI Deutschland GmbH Am Frauwald 12 65510 Idstein Deutschland Tel : 06126-9371-0 Fax: 06126-9371-14 E-Mail : info@eiki.de

Japan & Worldwide

EIKI Industrial Company Limited. 4-12 Banzai-Cho, Kita-Ku, Osaka, 530-0028 Japan Tel : +81-6-6311-9479 Fax: +81-6-6311-8486

Canada

EIKI CANADA - Eiki International, Inc. P.O. Box 156, 310 First St. - Unit 2, Midland, ON, L4R 4K8, Canada Tel : 800-563-3454 (705)-527-4084 Fax: 800-567-4069 (705)-527-4087 E-Mail : canada@eiki.com

Eastern Europe

EIKI CZECH spol. s.r.o. Umelecká 15 170 00 Praha 7 Czech Republic Tel : +42 02 20570024

+42 02 20571413 Fax: +42 02 20571411 E-Mail : easterneurope@eiki.de

WorldWide Website http://www.eiki.com

EIP-1600T_EN__cover 06.1.24, 1:11 PM6-7

Printed in China TINS-C312WJZZ 06P03-CH-NG

Eiki EIP-1600T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual