Table of Contents
1. Safety Instructions ··················································································· 2
2. The Projector ···························································································· 3
2.1 Features 3
2.2 Accessories 4
2.3 Appearance 5
3. Setting up the Projector ·········································································· 6
3.1 How to connect the projector 6
3.2 Turning on/off the projector 8
3.3 Adjusting the altitude of projected images 9
3.4 Adjusting the focus and zoom 10
3.5 Projected image size 11
4. How to use the Projector······································································· 12
4.1 Initial image adjustment 12
4.2 Control panel and remote controller 12
5. Menu ········································································································· 16
5.1 Image (VGA mode) 16
5.2 Image (Video mode) 17
5.3 Display (VGA mode) 18
5.4 Display (Video mode) 20
5.5 Audio 22
5.6 Management 23
5.7 Language 24
6. Maintenance ·····························································································25
6.1 Replacing the lamp 25
6.2 Cleaning lens 25
7. Appendix ·································································································· 26
7.1 Common problems & trouble-shooting 26
7.2 Specifications 28
1
1. Safety instructions
Before you use the projector, please read this manual thoroughly and
comply with the safety instructions hereunder. Improper use may cause fire,
electric shock, injuries, or reduce the life of your projector.
Warning: Please ensure the projector is grounded properly by connecting the
power cord to a grounded AC outlet. Do not defect the safety purpose of the
grounding type plug.
Warning: Do not cover the lens while the lamp lights.
Warning: To protect your eyes, please do not look at the projector’s light
source.
Warning: To replace the lamp, please turn off and unplug the projector first;
then wait for 1 hour before replacing the lamp. Please refer to
page 25 “Replacing the lamp” for the operation procedure.
Warning: Please use the power cord that comes with your projector. Please
use the grounded jack for safety.
Warning: Please do not block the openings around the projector for safety.
Warning: Do not place any drinks on top of the projector. The proje ctor can
be damaged if wet.
Warning: Do not place the projector in excessively warm or humid areas.
Please avoid direct sunshine.
Warning: To avoid electric shock, please do not dismantle the projector by
yourself if it is not working.
Warning: To prevent your projector from dropping, please be careful when
you move or carry it.
2
2. The projector
2.1 Features
• With the modularized structure of the product, all you need is the main
body when conducting a presentation, thereby making your job easier.
• XGA model can receive signals with resolution up to 1280x1024. T o
ensure the output quality, please adjust the setup of your computer
display card to be less than or equal to 1280 x 1024.
• Compact size, only 3.5 lbs.
TM
• Incorporated TI single chip 0.7” DLP
• Users may replace 150W (VIP R150/E20) lamp easily.
technology.
• Compatible with Mac / IBM PC 98.
• Compatible with NTSC/NTSC4.43/PAL/PAL-M/PAL-N/HDTV.
• Compatible with most interfaces comprising YCbCr, YPbPr, S-Video,
Composite Video/Audio.
• Fully functional remote controller, can be used as a mouse
• DVI connector can be connected to digital or standard image signals.
• Soft carrying case
3
2.2 Accessories
Please check if following accessories are in the box. If any items are missing,
please contact your dealer immediately.
Projector with lens cap Power cord M1DA-VGA+USB cable
Video/Audio cable PC Audio in/out cable S-video cable
VGA cable USB mouse cable Remote controller w/
AAA battery x 2
Soft Carrying Case
4
2.3 Appearance
ptor
Outlet Grille
Lens cover
Main Body
Infra Red Remote Receiver
Control panel
Zoom Ring
Focus Ring
Speaker
Video Enhanced
Ada
Screw
Warn ing Do keep the flow out of Outlet Grille free.
5
Foot Adjuster
Foot Adjuster button
3. Setting up the projector
3.1 How to connect the projector
Depending on your purpose, you can select any of the following connection
methods.
1) For displaying data only
Find the M1DA-VGA+USB cable; connect M1DA connector to the main body;
and connect VGA and USB connectors to the computer. Then you can start
presentation. Under such circumstance, video and audio function won’t be
available.
6
2) For playing video with audio effects
r
Connecting with the Video Enhanced Adaptor; and choose terminals below to
connect.
1. Power cord
2. VGA signal in port
3. USB mouse control
4. S-Video signal in port
5.6 Composite Video signal in port
7.8 PC Audio In/Out port
Notes
1. Please make sure that both projector and computer are
2. Plug USB cable into computer.
3. Plug one end of the VGA cable into the projector.;
4. Plug the other end into the computer.
5. Plug the power cord into the power connector on the side
6. Turn on projector first, then computer.
Connecting to a Compute
shutdown.
of projector; and plug into the socket.
7
3.2 Turning on/off the projector
Turning on the projector
1. Remove the lens cover.
2. Make sure the signal cables are connected.
3. Plug-in the power cord. LED indicator flashes slowly.
4. Press the Power key on the remote controller or control panel to turn on the
projector. LED indicator lights up consistently at this time.
5. The message “Warming up! Please wait.” appears on the screen of the
projector. Please wait for 20 seconds, the projector will detect the input signal
source automatically.
6. If the message “No Signal!” appears on the screen, please check if the signal
source has been activated or the signal cables have been connected.
7. To have the best image performance, press “Auto/Enter” each time when you
turn on the projector.
Caution When power is on, the projector will automatically detect if the
projector is overheated internally. If yes, the LED indicator flashes
rapidly and the fan cools down automatically after 8 seconds. The
Power key does not function under this situation.
Turning off the projector
1. Press the Power key to power off the projector lamp.
2. When you press the Power key, you’ll see the message “Press Power Key
again to power off lamp”. Then you can press the Power key to shutdown the
projector; or this message will disappear automatically after 5 seconds.
3. As soon as the lamp is off, the LED indicator flashes rapidly. The Power key
doesn’t function at this time.
Notes: Please wait at least 120 seconds before you turn on the projector again. You
should turn on the projector only after the LED indicator flashes slowly.
4. Unplug the power cord.
Caution To protect the lamp, please do not pull out the power cord right after the
lamp is off. Please wait at least 120 seconds when the fan stops.
8
3.3 Adjusting the altitude of the projected image
Foot Adjuster Button
Please use the foot adjuster to adjust the height of projector.
Higher
1. Hold the foot adjuster button.
2. Raise the projector to the height you like; and then release the foot adjuster to
fix the projector.
Lower
1. Hold the foot adjuster.
2. Lower projector to the height you like; and then release the foot adjuster to fix
the projector.
Foot Adjuster
9
3.4 Adjusting the focus and zoom
You can zoom in or out the image with the zoom ring. To enlarge the image size,
please turn the zoom ring counter-clockwise. To reduce the image size, please turn
the zoom ring clockwise. To adjust the focus of the image, please turn the focus
ring until the image becomes clear. The projection distance of the projector is
1.45 – 10 meters.
Focus Ring
Zoom Ring
10
3.5 Projected Image Size
Projection Distance 1.45M 2.0M 4M 6M 10 M
Tele Screen size 42” 49” 99” 148” 247”
Wide Screen Size 48” 57” 113” 170” 283”
11
4. How to use the projector
This section covers the methods of using and adjusting the projector, as well as the
methods of using the control panel, remote controller and menu.
4.1 Initial image adjustment
1 Please follow the previously stated steps to turn on the projector; and keep the
projector facing the screen.
2 Turn the zoom ring to adjust the size of the image.
3 Turn the focus ring to adjust the focus of the image.
4 Use the foot adjuster to adjust the altitude of the image.
5 Use either the control panel or remote controller to adjust the image for
horizontal position, vertical position or keystone.
6 Adjust the brightness, contrast and color temp of image with the menu.
4.2 Control panel and remote controller
There are two ways to use the projector – control panel and remote controller.
- Control Panel
LED Indicator
↑↓← →
Power
12
Auto/Enter
Menu
LED Indicator
When the projector is turned on, the LED indicator flashes. Press the Power
key to display the mage. At this time, the LED indicator lights up
consistently.
If the LED indicator flashes quickly, the projector is probably in an
abnormal condition. Possible reasons include:
a. If the fan is in an abnormal condition, the message “Fan lock error
occurred, Projector going shutdown!” appears on the screen.
b. If the temperature becomes abnormal, the message “Thermal error
occurred, Projector going shutdown!” appears on the screen.
LED indicator flashes quickly when you start the shutdown process.
Power
Please refer to page 8 “Turning on/off the projector”.
Auto/Enter
This key works as Auto key in normal condition.
This key works as an Enter key in the menu.
Menu
Press this key to open the menu. Press again to close the menu.
If you do not choose any items after opening the menu, then the menu will
automatically close after 20 seconds.
↑↓Keys
You can use the up and down keys to select menu options.
Usually the down key works as a Source key. You can also press this key to
select Analog RGB, Analog Y Pb Pr, Digital RGB, Composite Video,
S-Video and Component Video signals in sequence.
← → Keys
On the menu, press the Enter key and then the right key to increase the
setup value; or the left key to reduce the setup value.
13
- Remote controller
Key
Freeze/Esc/L
Enter/R
Power
Functions
Press this key to freeze the image. Press again to clear
the static image.
Press this key to quit the menu if the menu is on the
screen.
In the remote-control mouse mode, this key works as
the left key of mouse.
Please check page 13 “Auto/Enter” of “Control panel”
for the use of this key on the menu.
In the remote-control mouse mode, this key works as
the right key of mouse.
Please refer to page 8 “Turning on/off the projector”.
14
Mode
Press this key and green LED indicator turns on. Then
the remote controller can be used as a mouse.
" Be sure to connect USB mouse cable to the
computer and projector before using the remote
controller as a mouse.
Menu
Source
Blank
Auto
Pg.Up
Pg.Dn
↑↓←→
Please refer to page 13 “Menu” of “Control panel”.
Select Analog RGB, Analog Y Pb Pr, Digital RGB,
Composite Video, S-Video and Component Video
signals in sequence.
Convert the image into blank and fully blue. Press
again to restore.
Press this key to adjust the phase and frequency
automatically.
On the remote control mode, press this key to zoom in
the image (*).
When mouse is in use, press this key to turn to
previous page.
On the remote control mode, press this key to zoom
out the image (*).
When mouse is in use, press this key to turn to next
page.
Press this key and then left/right keys for keystone.
Press key to reduce the length of lower screen.
Press to reduce the length of upper screen.
(*)
"Do not activate when displaying text or spreadsheets to
eliminate text distortion
In the remote control mode, the function of these keys
is the same as the up/down/left/right keys on the panel
(*).
In the remote-control mouse mode, the function of
these keys is the same as the up/down/left/right key o
the mouse.
* Press Auto key to return to previous setup.
f
15
5. Menu
Press the Menu key to open the menu. You can press the up or down key to select the items on the menu; or press Esc to quit the menu. To enter the submenu, please press Enter key or right key. On the submenu, press the Menu or Esc key on the remote controller to return to the main menu; or press twice to quit menu.
5.1 Image (VGA mode)
Submenu Purpose Using
Brightness
(**)
Contrast To control the balance between
Keystone To modify the biased image
Zoom To enlarge/reduce the image Press key to zoom out the
* Press Auto key to return to previous setup.
** If the source is switched to HDTV/DVD 480P, the “Brightness” turns to “Tint”
to adjust the balance between red and blue colors in the image.
To adjust the brightness of
image
the brightest and darkest parts of
the image. You can change the
amount of black and white by
adjusting contrast.
resulted from the improper angle
of projector.
Press key to decrease
brightness.
Press to increase
brightness.
(*)
Press key to decrease
contrast.
Press to increase contrast.
(*)
Press key to reduce the
length of lower screen.
Press key to reduce the
length of upper screen.
(*)
image.
Press key to zoom in the
image (*)
Please press Enter key to
access to zoom pan mode.
In this mode, press keys
to move the image, press Pg
Up and Pg Dn keys on the
remote controller to zoom
in/out of image.
16
5.2 Image (Video mode)
Submenu Purpose Using
Brightness
Contrast To control the balance
Hue
Saturation
Sharpness
* Press Auto key to return to previous setup.
To adjust the brightness of
image.
between the brightest and
darkest parts of the image.
You can change the amount of
black and white.
To adjust the balance between
red and green colors in the
image.
To change the image from
black & white to saturated
colors.
To adjust the sharpness of the
image.
Press key to decrease
brightness.
Press key to increase
brightness.
(*)
Press key to decrease
contrast.
Press key to increase contrast.
(*)
Press key to increase the
green proportion.
Press key to increase the red
proportion.
(*)
Press key to decrease the
amount of colors in the image.
Press key to increase the
amount of colors in the image.
(*)
Press key to decrease the
sharpness.
Press key to increase the
sharpness.
(*)
17
5.3 Display (VGA mode)
Submenu Purpose Using
Frequency
Phase
V Position
H Position
To adjust the frequency of
data display to be the same
as the frequency of display
card of computer. Please
use this function to correct
the flickering vertical lines
shown in the image.
To synchronize the signals
of images and display
cards. Use this function to
correct inconsistent or
flickering images.
To adjust the vertical
position of screen.
To adjust the horizontal
position of screen.
Press key for
adjustment.
(*)
Press key for adjustment
(*)
Press key to move down
the image.
Press key to move up the
image.
(*)
Press key to move the
screen to left.
Press key to move the
screen to right.
(*)
18
Proportion
To select the aspect ratio of
screen, 16:9 or 4:3.
User Color
For end users to adjust red
green and blue colors on
their own.
User Red
User Green
User Blue
Color Temp
To adjust the Red color.
To adjust the Green color.
To adjust the Blue color.
To adjust the color temp in
the range between 6100K
and 9300K.
* Press Auto key to return to previous setup.
Press key for selection.
Choose Yes. User Red, User
Green and User Blue options
appear.
Choose No. Only Color Temp
option appears.
Press key to decrease
amount of Red color.
Press key to increase
amount of Red color.
(*)
Press key to decrease
amount of Green color.
Press key to increase
amount of Green color.
(*)
Press key to decrease
amount of Blue color.
Press key to increase
amount of Blue color.
(*)
Press key to lower color
temp; and the image looks
warmer.
Press to increase color
temp; and the image looks
cooler.
(*)
19
5.4 Display (Video mode)
Submenu Purpose Using
Keystone
Proportion
User Color
User Red
User Green
To modify the biased
image resulting from the
improper angle of
projector.
To select the aspect ratio
of screen, 16:9 or 4:3.
For end users to adjust
red green and blue
colors on their own.
To adjust the Red color.
To adjust the Green
color.
Press key to reduce the
length of lower screen.
Press key to reduce the
length of upper screen.
(*)
Press key for selection.
Choose Yes. User Red, User
Green and User Blue options
appear.
Choose No. Only Color Temp
option appears.
Press key to decrease
amount of Red color.
Press key to increase
amount of Red color.
(*)
Press key to decrease
amount of Green color.
Press key to increase
amount of Green color.
(*)
20
User Blue
Color Temp
To adjust the Blue color.
To adjust the color temp
in the range between
6100K and 9300K.
* Press Auto key to return to previous setup.
Press key to decrease
amount of Blue color.
Press key to increase amount
of Blue color.
(*)
Press key to lower color
temp; and the image looks
warmer.
Press to increase color temp;
and the image looks cooler.
(*)
21
5.5 Audio
Submenu Purpose or Using
Vo l um e
Treble
Bass
Mute
Press key to turn down the volume.
Press key to turn up the volume.
(*)
Press key to decrease the volume of treble.
Press key to increase volume of treble.
(*)
To adjust the medium/low frequency of audio.
Press key to decrease bass.
Press key to increase bass.
(*)
Select ”Yes” for Mute.
* Press Auto key to return to previous setup.
22
5.6 Management
Submenu Purpose Using
OSD Location
Projection
To display the position of menu on
the screen.
(Projection before the Screen)
Default
Press key for
selection (*)
Press key for
selection (*)
(Projection behind the Screen)
If you select this function, the
projector will reverse images from
left to right or vice versa. Thus the
image can be projected from behind
onto the semi-transparent screen.
Lamp Remind
To remind you of the number of
hours that the lamp has been lit up.
This function allows you to set up
the warning message to be displayed
30 hours before the end of the lamp
life.
23
Press key for
selection.
Lamp Reset
b
Auto Adjust
Reset All
Source Type
* Press “Auto” key to return to previous setup.
** HDTV: supporting EDTV 480p and HDTV 720p & 1080i.
To recount hours after replacing
the lamp.
For end users to fix the brightness
and contrast settings. This function
only works in the VGA mode.
To return to the factory default. Press the right key.
To select RGB, Composite,
Component, HDTV(**),S-Video,
signals or Auto Scan.
Press the right key. The
message “Press Enter key
to confirm lamp reset
operation!” appears. Please
check if the user has
replaced the new lamp. If
yes, press Enter key. If not,
press Menu key or Esc key
on the remote controller to
quit.
Choose Ye s. The values of
rightness and contrast vary
each time when pressing
Auto key.
Choose No. The values of
brightness and contrast
remain the same.
Press key for
selection.
5.7 Language
Please use up and down keys to choose the language you likened and press right
key to select. Press the Menu key or Esc key on the remote controller to return to
main menu.
24
6.1 Replacing the lamp
d
m
d
30 hours before the end of the lamp’s life time, the warning message “Lamp life
time is up! Replacement suggested!” will display on the screen. Please replace the
lamp immediately.
Steps:
1. Power off the projector.
2. Unplug the power cord.
3. Cool down projector for at least 30 minutes.
4. Use a screwdriver to remove the shell and screws on the lamp.
5. Remove lamp.
6. Gently process the new lamp module into the lamp bay, then replaces the lamp
module retaining screws.
7. Replace the lamp bay access panel, and then replace the access panel screw.
Remove screws from the lamp
cover with a screwdriver; an
then press down the lock to
open that cover.
Remove 3 screws fro
the lamp holder; an
pull out the handle to
replace the lamp in the
holder.
6.2 Cleaning lens
Please follow these steps to clean the projector lens:
1 Pour an adequate amount of cleanser to a piece of clean soft material. The lens
will be damaged if you use the cleanser containing particles, solvent, or other
inferior chemical solvent.
2 Use the soft material to wipe the lens in a circular direction.
3 Cover the lens with the cap if you are not going to use the projector right away.
25
7. Appendix
7.1 Common problems and trouble-shooting
If you are having a problem with your projector, please check the following:
If you still cannot solve the problem, please contact your local distributor or our
service center.
Q.: No image on the screen at all?
Make sure that you have properly connected the video enhanced adapter and
the relevant cables mentioned in previous chapters.
Make sure the plug is not bended or broken.
Please check if the lamp has been installed properly.
Please check if you have removed the lens cap and turned on the projector.
Q.: Incorrect resolution?
Please check if the video card of your computer has been set at a resolution
less than 1280 X 1024.
Q.: Unsteady or flickering image
Press the Auto key of the remote controller or the Auto/Enter key of the
projector.
Or use Phase on the Display menu to correct the problem.
You can also change the color setup of the display card on your computer.
Q.: Vertical flickering stripes on the image
Press the Auto key of the remote controller or the Auto/Enter key of the
projector.
You can also use Frequency on the Display menu to adjust the stripes.
Or re-set the display mode of your display card; and make it compatible with
the projector.
26
Q.: Image becomes blurred
Adjust the focus ring of the projector.
Make sure that distance between the screen and projector is adequate
(1.45~10m)
Q.: The colors projected by your projector look different from the colors of
your computer or VCR.
This is not a problem. You can adjust the brightness, color or contrast on the
menu to change colors.
Q.: When the projector is connected to a DVD player, playing a film with the
ratio 16:9, the image is reshaped.
Adjust the aspect ratio of the projector to 4:3.
Q.: Up-side-down image
Open the menu; and then select Management to adjust the projection
direction.
Q.: Lamp burned out or cracked.
The lamp burns out when its life is over. It might crack and sometimes the
broken pieces lead to the result that a blower is blocked and stops turning. In
such a case, please contact the licensed local distributor to purchase the
replacement. To change the lamp, please follow the steps stated in “Replacing
the lamp”.
27
7.2 Specifications
Model No.
Resolution
Size
Weigh t
Lamp
Brightness
Projection distance
Throw Ratio
Zoom Ratio
Uniformity
Aspect Ratio
Contrast Ratio
Horizontal Frequency
Vertical Scan Rate
Video compatibility
VGA compatibility
EIP-1
XGA (1024*768)
229 x 193 x 69 mm
3.5 lbs
150W VIP
1400 Lumens
1.45m ~10m
1.34:1 ~ 1.6:1 (Distance: Diagonal)
1.2:1 (Manual Zoom/Focus)
85%
4:3 / 16:9 screen selectable
900:1
31.5 - 80 kHz
56 - 85 Hz
NTSC / PAL
RGB/DVD 480P, HDTV (1080i/720P/480P)
Power supply
Power Consumption
100 to 240 VAC, 0.91A~2.2A,50 to 60 Hz
220W
28
Input Terminal
DVI (M1DA) USB RGB (M1DA-D-Sub 15 pin)
RS232 (M1DA) YPbPr (M1DA,VGA) S-Video Mini DIN 4 pin
Audio: RCA Jack 3.5mm Mini Jack Composite Video (RCA Jack)
Output Terminal
1 watt speaker
* All specifications are subject to change without notice.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) the device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
29
Loading...