Eiki EFD-52, EFD-56, EFD-46 Owner's Manual
LCD MONITOR
EFD-52
EFD-46
OWNER’S MANUAL
EIKI INDUSTRIAL CO., LTD.
IMPORTANT
• For your assistance in reporting the loss or theft of your monitor, please
record the Model and Serial Number located on the rear of the monitor
and retain this information.
• Before recycling the packaging, please ensure that you have checked the
contents of the carton thoroughly against the list of “Supplied accessories”
on page 8.
Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 10A fuse.
Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the
same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse cover fi tted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off
the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
or coloured green or green-and-yellow.
• The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian and
Arabic. Carefully read through the operation instructions before operating the monitor.
• Die mitgelieferte CD-ROM enthält Betriebsanleitungen auf Englisch, Deutsch, Französisch, Spanisch,
Italienisch und Arabisch. Lesen Sie die Betriebsanleitung sorgfältig durch, bevor Sie den Monitor in
Betrieb nehmen.
• Le CD-ROM fourni contient les instructions d’utilisation en anglais, allemand, français, espagnol, italien
et arabe. Lisez attentivement ces instructions avant d’utiliser le moniteur.
• El CD-ROM suministrado contiene instrucciones de uso en inglés, alemán, francés, español, italiano y
árabe. Lea atentamente las instrucciones de uso antes de utilizar el monitor.
• Il CD-ROM fornito in dotazione contiene istruzioni in inglese, tedesco, francese, spagnolo, italiano e
arabo. Leggere attentamente le istruzioni d’uso prima di utilizzare il monitor.
ii
•
•
DEAR EIKI CUSTOMER
Thank you for your purchase of an EIKI LCD Monitor. To ensure safety and many years of troublefree operation of your product, please read “IMPORTANT INFORMATION” and “IMPORTANT SAFETY
INSTRUCTIONS” carefully before using this product.
IMPORTANT INFORMATION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
FCC Regulations state that any unauthorized changes or modifi cations to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this
equipment.
The lightning fl ash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of suffi cient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions
in the literature accompanying the
product.
U.S.A. ONLY
CAUTION:
This product satisfi es FCC regulations when shielded cables and connectors are used to
connect the unit to other equipment. To prevent electromagnetic interference with electric
appliances such as video equipments, use shielded cables and connectors for connections.
U.S.A. ONLY
1
IMPORTANT INFORMATION
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
DECLARATION OF CONFORMITY:
EIKI LCD MONITOR, MODEL EFD-52/EFD-46
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
EIKI INTERNATIONAL, INC.
30251 Esperanza Rancho Santa Margarita, CA 92688-2132
TEL: 800-242-3454
U.S.A. ONLY
U.S.A. ONLY
This product utilizes tin-lead solder, and fl uorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal
or recycling information, please contact your local authorities, the Electronic Industries Alliance:
www.eiae.org, the lamp recycling organization: www.lamprecycle.org or 1-800-242-3454
U.S.A. ONLY
Authorized representative responsible for the European Union Community Market
EIKI Deutschland GmbH
Am Frauwald 12, 65510 Idstein
E.U. ONLY
Trademarks
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
• “HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC.”
• All other brand and product names are trademarks or registered trademarks of their respective holders.
2
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if
improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fi re. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your LCD Monitor, please read the following precautions carefully before using the
product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifi ers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachments/accessories specifi ed by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Additional Safety Information
15) Power Sources — This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fi re or electric shock.
17) Object and Liquid Entry — Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fi re or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualifi ed service
personnel under the following conditions:
a) When the power cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualifi ed technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts — When replacement parts are required, be sure the service technician has used
replacement parts specifi ed by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fi re, electric shock, or other hazards.
20) Safety Check — Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall mounting — When mounting the product on a wall, be sure to install the product according to the
method recommended by the manufacturer.
22) The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
3
IMPORTANT SAFETY INSTRUCTIONS
• Water and Moisture — Do not use this product near water - for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to
the product. Use a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with
the product. Do not allow the monitor to receive strong shocks or to strongly vibrate. When mounting
the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting
hardware recommended by the manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover
or block these vents and openings since insufficient ventilation can cause overheating and/or shorten
the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they
can block ventilation openings. This product is not designed for built-in installation; do not place the
product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can
break when the product is dropped or applied with impact. Be careful not to be
injured by broken glass pieces in case the panel breaks.
• Heat — The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture
details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Also, if the screen is viewed from an acute angle there may be uneven colors or brightness.
Please note that this does not affect the performance of your product.
Precautions when transporting the monitor
• Be sure to always carry the monitor by two people holding it with two
hands — one hand on each side of the monitor.
• Do not hold onto the attached optional speakers when transporting the
monitor.
• Lightning — For added protection for this monitor equipment during a
lightning storm, or when it is left unattended and unused for long periods
of time, unplug it from the wall outlet. This will prevent damage to the
equipment due to lightning and power-line surges.
4
IMPORTANT SAFETY INSTRUCTIONS
• To prevent fire, never place any type of candle or flames on the top or near the
monitor.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• To prevent fire or shock hazard, do not place the power cord under the monitor or
other heavy items.
• Turn off the power and unplug the power cord from the wall outlet before handling.
• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may scratch the
panel surface.
• Use a soft damp cloth to gently wipe the panel when it is really dirty.
(It may scratch the panel surface when wiped strongly.)
• If the panel is dusty, use an anti-static brush, which is commercially
available, to clean it.
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical
cloth to clean it, such materials may damage the panel surface.
• To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• Never rub or tap the monitor with hard objects.
• Please understand that EIKI INDUSTRIAL CO., LTD. bears no responsibility for errors made during use
by the customer or a third party, nor for any other malfunctions or damage to this product arising during
use, except where indemnity liability is recognized under law.
• This monitor and its accessories may be upgraded without advance notice.
• Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may
come into contact with oil or steam, as this could lead to fi re.
• Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fi re or electric
shock.
Fluorescent tubes
• The fl uorescent tubes in this product have a limited lifetime.
* If the screen gets dark, fl ashes, or does not turn on, change the fl uorescent tubes with new exclusive
ones.
* For more information, please contact your product dealer.
• Because of the property of fl uorescent tubes, the screen may fl ash during the initial period of use. If this
happens, please turn off the power of the monitor and turn on again to confi rm operation.
5
Contents
Introduction
DEAR EIKI CUSTOMER ................................ 1
IMPORTANT INFORMATION ......................... 1
Trademarks .................................................... 2
IMPORTANT SAFETY INSTRUCTIONS ....... 3
How to Access the PDF Owner’s
Manuals ....................................................... 7
SETUP MANUAL ....................................... 7
Accessories ................................................... 8
Part Names ..................................................... 9
Preparation
How to Install the Monitor .......................... 12
Mounting precautions .............................. 12
Attaching the setup stand ........................ 12
Mounting the monitor on the wall ............. 13
Connecting Peripheral Equipment ............ 15
Connecting external speakers ................. 18
Connecting multiple monitors .................. 18
Controlling the monitor by a computer..... 19
Connecting the Power Cord ....................... 20
Binding Cables ............................................20
Preparing the Remote Control ................... 21
Installing the batteries .............................. 21
Remote control operation range .............. 21
Operation
Turning the Monitor On/Off ........................ 22
Turning on the power ...............................22
Turning off the power ............................... 22
Operating with the Remote Control .......... 23
Switching the input mode ........................ 23
Adjusting the volume ............................... 23
Displaying the black screen and turning
off the sound temporarily ....................... 23
Resize mode ............................................ 24
Auto Sync adjustment (Auto Sync) .......... 26
Freezing a moving image ......................... 26
Selecting AV mode ..................................26
Displaying an enlarged portion of
an image ................................................ 26
Split-screen viewing ................................. 27
Menu Operations ......................................... 28
Basic menu operations ............................28
List of menu items .................................... 29
Picture menu ............................................ 30
Audio menu .............................................. 32
Power Control menu ................................32
Setup menu .............................................. 33
Option menu ............................................38
Appendix
Troubleshooting .......................................... 43
Specifi cations .............................................. 44
Index ............................................................. 49
6
How to Access the PDF Owner’s Manuals
PDF owner’s manuals in several languages are included in the CD-ROM. To utilize these manuals,
you need to install Adobe
Please download Adobe
Accessing the PDF manuals
For Windows®:
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 When you want to view the owner’s manual
1) Double click the “MANUALS” and the
“EFD52_46” folder.
2) Double click the language (name of the folder)
that you want to view.
3) Double click the PDF fi le to access the owner’s
manual.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” and the “EFD52_46”
folder.
2) Double click the language (name of the folder)
that you want to view.
3) Double click the PDF fi le to access the SETUP
MANUAL.
®
Reader® on your computer (Windows® or Macintosh®).
®
Reader® from the Internet (http://www.adobe.com).
For Macintosh
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “CD-ROM” icon.
3 When you want to view the owner’s manual
1) Double click the “MANUALS” and the
“EFD52_46” folder.
2) Double click the language (name of the folder)
that you want to view.
3) Double click the PDF fi le to access the owner’s
manual.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” and the “EFD52_46”
folder.
2) Double click the language (name of the folder)
that you want to view.
3) Double click the PDF fi le to access the SETUP
MANUAL.
®
:
Note
• If the desired PDF fi le cannot be opened by double clicking the mouse, start Adobe® Reader® fi rst, then specify the desired
fi le using the “File”, “Open” menu.
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
RS-232C Specifi cations and Commands ....................... 2
Setting up the Monitor Network Environment ............... 10
Controlling the Monitor via LAN .................................... 16
Setting up the Monitor Using RS-232C or Telnet ......... 21
Multi Screen .................................................................. 31
Troubleshooting ............................................................ 39
7
Accessories
Supplied accessories
If any component should be missing, please contact your dealer.
Liquid Crystal Display: 1
Power cord (Approx. 6 feet [1.8 m])
(1) For U.S. and Canada, etc.
<QACCDA007WJPZ>
(2) For Europe, except U.K.
<QACCVA011WJPZ>
LAN cable (UTP cable, Category 5, straight-through type): 1
<QCNWGA133WJPZ>
R-6 battery (“AA” size, UM/SUM-3, HP-7 or similar): 2
CD-ROM: 1
Owner’s manual: 1
Remote control: 1
<RRMCGA760WJSA>
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Note
• Use the power cord that corresponds to the wall outlet in your country.
Optional accessories
The listed optional accessories are available for the LCD Monitor.
Please contact the nearest EIKI Authorized Dealer.
Speaker unit: SP-EF5201 (for EFD-52), SP-EF4601 (for EFD-46)
Wall-mount bracket: WB-EF5201 (for EFD-52 and EFD-46)
Note
• Some of the optional accessories may not be available depending on the region. Please check with your nearest EIKI
Authorized Dealer or Service Center.
• Additional optional accessories may be available in the near future. When purchasing, please read the newest catalog for
compatibility and check the availability.
Setup stand: 1
Cable clamp: 1
Power cord clamp: 1
8
Front view
Rear view
LAN
terminal
(See page 19.)
RS-232C
terminal
(See page 19.)
LCD panel
Part Names
POWER indicator (See page 22.)
TIMER indicator (See page 41.)
OPC indicator (See page 31.)
OPC sensor (See page 31.)
Remote control sensor (See page 21.)
CAUTION
The area surrounding these terminals
gets hot. Exercise due caution when
HOT
Handles (Fixed type)
handling. (EFD-46 only)
AC input terminal
(See page 20.)
DVI IN
terminals
(See pages
15, 16 and 17.)
HDMI
terminal
(See page 16.)
COMPUTER IN 1 terminals
(
See pages 15, 16 and 17.
Note
• The illustrations in this owner’s manual are for explanation purposes and may vary slightly from the actual operations.
• The illustrations used throughout this manual are based on EFD-52.
COMPUTER IN 2 terminals
)
(
See pages 15, 16 and 17.
MONITOR OUT terminals
)
(See page 17.)
SPEAKER OUT terminals
(See page 18.)
9
Part Names
Side view
POWER button
For turning the main power on.
(See page 22.)
MENU button
For displaying adjustment and setting screens.
(See page 28.)
ENTER button
For setting items selected or adjusted on the menu.
(See page 28.)
INPUT buttons (
For selecting the input mode.
(See page 23.)
VOL (Volume) buttons (+/–)
For adjusting the speaker sound level.
(See page 23.)
Adjustment buttons (Ÿ/ź/Ż/Ź)
For selecting and adjusting menu items.
(See page 28.)
S-VIDEO IN terminal
(See pages 16 and 17.)
VIDEO IN terminal
(See pages 16 and 17.)
AUDIO terminals
(See page 17.)
/ )
10
Remote control
Part Names
STANDBY button
For putting the monitor into
the standby mode.
(See page 22.)
FREEZE button
For freezing images.
(See page 26.)
MAGNIFY buttons
For enlarging/reducing part of
the image.
(See page 26.)
Adjustment buttons
(Ÿ/ź/Ż/Ź)
For selecting and adjusting
menu items.
(See page 28.)
P&P button
For setting the split-screen picture
mode. Press P&P again to return to
normal view.
(See page 27.)
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
(See page 26.)
ON button
For turning the power on.
(See page 22.)
COMPUTER 1, COMPUTER 2, DVI,
HDMI, S-VIDEO, VIDEO buttons
For switching to the respective input
modes.
(See page 23.)
AV MUTE button
For temporarily displaying a black
screen and turning off the sound.
(See page 23.)
VOL (Volume) buttons (+/–)
For adjusting the speaker sound level.
(See page 23.)
MENU button
For displaying adjustment and setting
screens.
(See page 28.)
ENTER button
For setting items selected or adjusted
on the menu.
(See page 28.)
RETURN button
For returning to the previous menu
screen during menu operations.
(See page 28.)
RESIZE button
For switching the picture size.
(See page 24.)
SELECT button
For selecting either screen to be active
in split-screen mode.
(See page 27.)
AV MODE button
For selecting appropriate settings for
picture and audio.
(See page 26.)
11
How to Install the Monitor
Mounting precautions
• Mounting the monitor on the wall requires special expertise and the work must be performed by an
authorized EIKI dealer. You should never attempt to perform any of this work yourself. Our company will
bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary
for some materials such as plaster / thin plastic board / wood before starting installation.
This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight
of the monitor. Install by the most suitable method for the material and the structure.
• This monitor can not be installed in a vertical orientation.
• Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
• When installing, removing or moving the monitor, ensure that this is carried out by at least 2 people.
• When moving the monitor, be sure to hold it with the handles both on the rear and the unit bottom. Do not
hold the LCD panel. This may cause product damage, failure, or injury.
• This monitor should be used at an ambient temperature between 32°F (0°C) and 104°F
(40°C). Provide enough space around the monitor to prevent heat from accumulating inside.
• Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a
malfunction.
• Do not place the monitor on a device which generates heat.
Attaching the setup stand
Before performing work spread cushioning over the base area to lay the monitor on. This will prevent it from
being damaged.
Caution
• Please note that the setup stand is for temporary use only until the monitor is properly mounted.
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the monitor falling over.
12
Confi rm that there are 10 screws and 6 caps
supplied with the stand.
Assemble the stand using the 6 screws.
34
Put the caps on the screws that have been
screwed into the stand.
Remove the protective covers from the underside
of the monitor.
12
How to Install the Monitor
0°/5°/10°/15°/20°
56
Insert the stand into the openings on the
underside of the monitor.
Note
• To detach the stand, perform the steps in reverse order.
• Store the protective covers. You will need them after detaching the stand.
Insert and tighten the screws into the 4 holes on
the rear of the monitor.
Mounting the monitor on the wall
Handling and precautions with the wall-mounted monitor
• You can mount the monitor on the wall using the optional WB-EF5201 bracket.
• For details, refer to the instructions supplied with the optional WB-EF5201 bracket.
Caution
• This monitor should be mounted on the wall only with the WB-EF5201 (EIKI) wall-mount bracket. The use
of other wall-mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the monitor requires special skill that should only be performed by qualifi ed service personnel.
Customers should not attempt to do the work themselves. EIKI bears no responsibility for improper
mounting or mounting that results in accident or injury.
Using an EIKI recommended bracket to mount the monitor
• You can ask a qualifi ed service professional about using an EIKI recommended WB-EF5201 bracket to
mount the monitor to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
WB-EF5201 wall-mount bracket. (See the bracket instructions for details.)
About setting the monitor angle
Vertical mounting Angular mounting
• The center of the display
EFD-52:
The “f” position is at the center
of the display.
EFD-46:
The “b” position is at the center
of the display.
• Refer to the owner’s manual of
WB-EF5201 for details.
WB-EF5201
13
How to Install the Monitor
Mounting the monitor on the wall
Attach the monitor to the wall-mount brackets according to the procedure below.
12
Use the protective cover to prevent dust from
Unfasten the 4 screws used to secure the stand in
place.
entering the underside of the monitor where the
stand has been detached.
3
Detach the 4 caps at the 4 locations on the rear of
the monitor.
5
4
Connect and bind the power cord and terminal
cables.
6
Attach the wall-mount brackets (L/R).
14
Set the monitor on the wall.
Loading...