Eiki Digital projector, 1AV4U19B25500 Owner's Manual

Download

Network Set-up and Operation For Windows

Wired and Wireless Setting

Projector Set-up and Operation

Network Capture

Network Viewer

Moderator Function

Owner’s Manual

This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed strictly.

Compliance

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. – Consult the dealer or an experienced radio/TV technician for help. Model Number : 1AV4U19B25500 Trade Name : EIKI Responsible party : EIKI International, Inc. Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132 Telephone No. : 800-242-3454 (949-457-0200) This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) the device may not cause interference, and (2) the device must accept any interference, including interference that may cause undesired operation of this device.

CAUTION: Properly shielded a grounded cables and connectors must be used for connection to host

computer and /or peripherals in order to meet FCC emission limits.

VGA cable with ferrite core must be used for RF interference suppression.

For Canadian Users

This Class B digital apparatus complies with Canadian ICES-003. Cet apparei numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC RF Exposure Warning

- This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

- This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment

and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities: hands, wrists, feet and ankles).

This projector provides the wireless LAN module which complies with the module certification.

The CE Mark is a Directive conformity mark of the European Community (EC).

The Alert Mark is a Directive conformity mark of the European Community.

English

Hereby, EIKI Deutschland GmbH declares that this WLAN Module (1AV4U19B25500) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Česky

[Czech]

EIKI Deutschland GmbH tímto prohlašuje, že tento WLAN Module (1AV4U19B25500) je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk

[Danish]

Undertegned e EIKI Deutschland GmbH erklærer herved, at følge nde uds tyr WLAN Module (1AV4U19B25500) overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Deutsch

[German]

Hiermit erklär t EIKI Deutschland GmbH dass sich das Gerät WLAN Module (1AV4U19B25500) in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti

[Estonian]

Käesolevaga kinnitab EIKI Deutschland GmbH seadme WLAN Module (1AV4U19B25500) vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Español

[Spanish]

Por medio de la presente EIKI Deutschland GmbH declara que el WLAN Module (1AV4U19B25500) cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ EIKI Deutschland GmbH ΔΗΛΩΝΕΙ ΟΤΙ WLAN Module (1AV4U19B2550 0) ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français [French]

Par la présente EIKI Deutschland GmbH déclare que l’appareil WLAN Module (1AV4U19B25500) est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Italiano [Italian]

Con la presente EIKI Deutschland GmbH dichiara che questo WLAN Module (1AV4U19B25500) è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Latviski

[Latvian]

Ar šo EIKI Deutschland GmbH deklarē, ka WLAN Module (1AV4U19B25500) atbilst Direktīvas 1999/5/ EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]

Šiuo EIKI Deutschland GmbH deklaruoja, kad šis WLAN Module (1AV4U19B25500) atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Nederlands

[Dutch]

Hierbij verklaart EIKI Deutschland GmbH dat het toestel WLAN Module (1AV4U19B2550 0) in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/ EG.

Malti

[Maltese]

Hawnhekk, EIKI Deutschland GmbH jiddikjara li dan WLAN Module (1AV4U19B25500) jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Magyar

[Hungarian]

Alulírott, EIKI Deutschland GmbH nyilatkozom, hogy a WLAN Module (1AV4U19B25500) megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski

[Polish]

Niniejszym EIKI Deutschland GmbH oświadcza, że WLAN Module (1AV4U19B25500) jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Português

[Portuguese]

EIKI Deutschland GmbH declara que este (1AV4U19B25500) está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Slovensko

[Slovenian]

EIKI Deutschland GmbH izjavlja, da je ta (1AV4U19B25500) v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky

[Slovak]

EIKI Deutschland GmbH týmto vyhlasuje, že (1AV4U19B25500) spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

Suomi

[Finnish]

EIKI Deutschland GmbH vakuuttaa täten että (1AV4U19B25500) tyyppinen laite on direktiivin 1999/5/ EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska

[Swedish]

Härmed intygar EIKI Deutschland GmbH att denna (1AV4U19B25500) står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Islenska

[Icelandic]

Hér með lýsir EIKI Deutschland GmbH yfir því að (1AV4U19B25500) er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Norsk

[Norwegian]

EIKI Deutschland GmbH erklærer her ved at utstyret (1AV4U19B25500) er i sams var med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Safety instructions

Caution about Radio Wave

This unit operates in 2.4 GHz band, the same frequency band used for industrial, scientific, and medical equipment (such as pacemaker), as well as amateur radio stations.

Please read “Safety Instructions” section and make sure the following cautions.

1. Be sure that there are no other devices in the area that may use the same frequency band as

Projector.

2. If any other devices are causing radio interferences, change the communication frequency channel

or move to other location.

Trademarks and Copyright

Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Netscape Navigator and Netscape Communicator are registered trademarks or trademarks of Netscape Communications Corporation in the United States and other countries. Pentium is a registered trademark of Intel Corp. in the United States. Each name of corporation or product in this Owner’s Manual is either a registered trademark or a trademark of its respective corporation.

Notes

- The contents of this manual are subject to change without notice.

- You may not copy the printed materials accompanying with the software.

- We shall not be responsible for any damages caused by reliance on this manual.

Expression/Abbreviation

The OS of the computer and the Web browser described in this manual is Windows XP Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruction procedures may differ from the actual operation depending on your computer environment.

Use of this manual

This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective booklet.

CAUTION IN USING THE PROJECTOR VIA NETWORKS

● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents.

● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents.

CAUTION IN USING NETWORK FUNCTION

● EIKI Industrial Co., Ltd. assumes no responsibility for the loss or damage of data, or damage of the computer caused by using this projector. Making back-up copies of valuable data in your computer is recommended.

Table of contents

Compliance .........................................................................................................................................................2

Safety instructions ............................................................................................................................................4

Table of contents ...............................................................................................................................................5

Operating environment and configuration .............................................................................................8

Required operating environment for computers ..............................................................................8

Network specifications of the projector ................................................................................................9

Useful guide to the network function .......................................................................................................10

How to project the computer screen’s image via the network .....................................................10

How to setup or control the projector by using a PC via the network .......................................10

How to use all functions concerning the network ............................................................................10

1. About LAN functions ....................................................11

LAN functions and the features ................................................................................................................12

Image projecting system via LAN ............................................................................................................12

An example of the connection .................................................................................................................13

LAN connection modes ...............................................................................................................................14

2. Setup procedures .........................................................17

Installing the software .................................................................................................................................19

3. Names and functions of the operation screen ...........23

Network connection standby display ....................................................................................................24

Network Capture 5 window .......................................................................................................................25

4. Wired LAN configurations ...........................................27

Connecting to the LAN line........................................................................................................................28

Network environment settings.................................................................................................................28

Confirming the operation ...........................................................................................................................30

Network PIN code ..........................................................................................................................................32

Network information ....................................................................................................................................32

Wired factory default....................................................................................................................................33

Wired LAN factory default settings .........................................................................................................34

5. Wireless LAN configurations .......................................35

Setting the network environment ...........................................................................................................36

Setting procedures........................................................................................................................................36

Configuring security with the projector ................................................................................................38

Easy wireless setting .....................................................................................................................................41

Network PIN code ..........................................................................................................................................42

Network information ....................................................................................................................................42

Wireless factory default ...............................................................................................................................42

WIRELESS indicator display ........................................................................................................................43

Wireless LAN factory default settings ....................................................................................................44

6. Basic setting and operation .........................................45

Starting up the Browser ..............................................................................................................................46

How to use the setting page .....................................................................................................................48

Initial setting ....................................................................................................................................................50

Network configuration ................................................................................................................................53

Configuring wireless LAN setting and security setting....................................................................55

E-mail setting ..................................................................................................................................................57

SNMP setting ...................................................................................................................................................61

7. Controlling the projector ............................................65

Power control and status check ...............................................................................................................66

Controls .............................................................................................................................................................68

PC adjustment ................................................................................................................................................72

Setting up the projector ..............................................................................................................................73

Timer setting ...................................................................................................................................................76

Projector information ...................................................................................................................................79

Multi-control ...................................................................................................................................................81

8. Network capture functions .........................................87

About Network Capture function ............................................................................................................88

Using the Real Time Capture .....................................................................................................................91

Using the Network Communication .......................................................................................................96

How to use the Network communication ...........................................................................................100

Network Communication operation and change of state ..............................................................103

Executing the forcing mode ......................................................................................................................104

Moderator function ......................................................................................................................................105

Preparation for using the moderator function ...................................................................................106

Using the moderator function ..................................................................................................................107

Moderator's password setting up ............................................................................................................108

Unregister moderator status .....................................................................................................................108

Error information ...........................................................................................................................................109

Playing the movie files .................................................................................................................................110

9. Network Viewer functions............................................113

Creating the available data [Network Viewer 5] .................................................................................114

Creating a program file [Program Editor] ..............................................................................................119

Using the Network Viewer function ........................................................................................................124

Use of the projector as FTP server ...........................................................................................................130

10. Network Projector [Windows Vista] ..........................133

Use of "Connect to a Network Projector" ..............................................................................................134

11. Appendix .....................................................................137

Use of telnet ....................................................................................................................................................138

Web browser setting ....................................................................................................................................140

Firewall setting ...............................................................................................................................................145

Troubleshooting.............................................................................................................................................146

Terminology.....................................................................................................................................................152

When operating the projector via the networks, computers should meet the operating environment below.

Required operating environment for computers

Operating environment and configuration

Microsoft Windows 2000 or Microsoft Windows XP or Microsoft Windows Vista (32bit version)

CPU

Pentium 3 ; 1GHz or higher (more than 2GHz is recommended) for Windows 2000 or Windows XP Pentium 4 ; 3GHz or higher for Windows Vista

Memory

256MB or more for Windows 2000 or Windows XP 1GB or more for Windows Vista

Free HDD Space 100MB

Screen Resolution

Required to support any of VGA (640 x 480), SVGA (800 x 600), XGA (1024 x 768), The color number should be either 16 bit (65536 colors) or 24/32 bit (16.77 million colors).

Communication Protocol TCP/IP

Network

Correspond

Wireless LAN Correspond to IEEE802.11b/g, IEEE802.11n (Draft 2.0)

Wired LAN

Correspond to 100BASE-TX (100Mbps) /10BASE-T (10Mbps)

Browser Application

Microsoft Internet Explorer Ver.4.0 or later Netscape Communications Netscape Communicator Ver.6.0 or later

Network specifications of the projector

LAN Terminal

Wireless LAN

Compliance

Data communication speed 100Base-TX (100Mbps)/10Base-T (10Mbps)

Protocol TCP/IP

Interface IEEE802.11b/g, IEEE802.11n(Draft 2.0)

Communication Mode

AdHoc, Infrastructure

Data Transfer Speed

1/2/5.5/11Mbps (IEEE802.11b) 6/9/12/18/24/36/48/54Mbps (IEEE802.11g) Max speed 150Mbps (IEEE802.11n)

Wireless Frequency (Channel) 2412MHz–2462MHz (CH1–CH11)

Modulation Form

IEEE802.11g OFDM 54/48Mbps 64QAM, 36/24Mbps 16QAM, 18/12Mbps QPSK, 9/6Mbps BPSK IEEE802.11b DSSS 11/5Mbps CCK, 2Mbps DQPSK, 1Mbps DBPSK IEEE802.11n OFDM

Protocol TCP/IP

Security

WEP 64Bit (Open/Shared) /WEP 128Bit (Open/Shared), WPA-PSK(TKIP), WPA2-PSK(AES), SSID, ESSID

Service area

about 30 m (without disturbance) Differs according to the operating environment.

Countries and Standards

JAPAN: VCCI ClassB,TELEC (Wireless)

USA: FCC Part15 Subpart C (Wireless) FCC Part15 Subpart C, Class B

Canada: IC RSS-210 (Wireless), IC ICES-003 ClassB

Europe: R&TTE, EMC, LVD

Did you make a network setting in the projector?

Check 1

This manual describes the operation procedure of the projector’s network menu and the provided application software for Windows users. Please refer to this manual depending on the situation.

● How to project the computer screen’s image via the network

Useful guide to the network function

● How to setup or control the projector by using a PC via

the network

● How to use all functions concerning the network

To use all functions concerning the network of this projector, you need to make a network setting in the projector and install the supplied application. Please follow the procedure on page 18.

Did you install the supplied application?

Check 2

Did you make a network setting in the projector?

Check

Yes No

Project the image by using the Auto Capture program on the supplied USB memory. (p.95)

To project the computer screen’s image via the network, you need to make a network setting in the projector and connect the projector to the network, or if you use the supplied USB memory, you can project the computer screen’s image via the network without making a network setting.

Yes No

• Control by the projector (p.91, 94)

• Control by the web browser (p.91, 93)

• Use of "Connect to a Network Projector" in the Windows Vista (p.134)

Yes No

You cannot setup or control the projector via the network without making a network setting in the projector. Please make a network setting. [Wired LAN configurations (p.27-34)/Wireless LAN configurations (p.35-44) ]

To setup or control the projector via the network, you need to make a network setting in the projector and connect the projector to the network.

Project the image by using the Real Time Capture function in the supplied ‘Network Capture 5’ application. (p.91, 92)

Setup or control the projector by controlling the web browser of the PC. [Setup (p.45-64)/ Control p.65-86) ].

Chapter

This chapter describes the features, the mechanism, and connection procedures of the LAN.

1. About LAN functions

Chapter 1 About LAN functions

LAN functions and the features

This product is loaded with a LAN network function which enables you to project an image on the computer through a projector via Network with dedicated software. With the software, you can also manipulate the projecting image and the projector. This software has functions below and you can use the projector under various network environments to meet the wide-ranging needs of the operation.

• Accept both Wired and Wireless LAN environment. When the projector is operated via Wireless LAN, there is no need for wire connection.

• Remove the burden of LAN settings. Easy LAN setting function is provided.

• One computer image can be projected up to 5 projectors simultaneously.

• Network capture function to project the computer's screen image through the projector.

• Remote function which allows you to operate the projector from a distance.

• Monitoring function for the projector operation.

• E-mail function which reports the operating status to your maintenance management.

• Network viewer function which remotely operates the image data on the server to project through the projector.

• Moderator function with which the moderator can project the image on the participants’ computer screen at the meetings or the classes.

• Multi control function which can operate multiple projectors (up to 100) simultaneously.

Image projecting system via LAN

The images are projected through an image capturing system which helps to project the faithful computer images. With this system, you can use the product under various application environments despite the differences of application software.

1. Download the computer image with the dedicated software faithfully to the real image.

2. The downloaded data will be compressed to the digital signal and transferred to the projector via the

LAN (Wired or Wireless). (One computer can operate up to 5 projectors simultaneously.)

3. Digital signal will be reproduced into RGB image signal and will be projected by the projector.

✳ The image will be transferred to each projector. The time lag can occur between each projection.

Flow of Image Transfer

CAUTION: This product does not correspond to the application with DirectX, MSOffice assistant, and video replay such as DVD.

An example of the connection

The illustration below shows an example of the projection via the LAN. You can project the image on Computer (1) (Wired LAN connection), or Computer (2) (Wireless LAN connection) through the selected projector .

0.0

0.5

1.0

1.5

2.0

0.0

0.5

1.0

1.5

2.0

0.0

0.5

1.0

1.5

2.0

Access pointComputer (1)

Computer (2)

An example of the connection

Chapter 1 About LAN functions

■ Wireless LAN, Infrastructure Communication Mode

Access pointComputer (1)

Wireless communication mode corresponded computer: Infrastructure

■ Wireless LAN, AdHoc Communication Mode

Communication mode between Wireless LAN equipment. (Communication mode via SSID/ESSID)

Wireless communication mode corresponded computer: AdHoc

Computer (2)

Network Projector

Wireless communication mode :AdHoc

Communicate over an access point between Wired LAN equipment and Wireless LAN equipment. Or, communicate over an access point among multiple Wireless LAN equipment. Wireless LAN equipment will select an access point to communicate SSID/ESSID modes. These communication modes are used when both Wireless LAN and Wired LAN are used in the same network environment.

LAN connection modes

Connection modes differ depending on the LAN and computer environments. Connect appropriately for each environment.

■ Wired LAN Communication Mode

Communicate via the LAN line.

Computer(1) Computer(2) Computer (3)

LAN connection modes

✳ Operate the computer mouse with the remote control. When the projector’s remote control employs mouse operating function, you can operate the

computer by the remote control. To use the remote control, point to the projector. You do not need to connect the USB cable to operate the computer mouse.

Chapter 1 About LAN functions

Chapter

This chapter describes how to install the Network Capture 5 software and how to set up the networks.

2. Setup procedures

Chapter 2 Setup procedures

To use the projector via the networks, follow the setup procedures below.

STEP 1

Install the software on computers.

Install the software recorded in CD-ROM on each computer which will be operated. Read following pages of this chapter to install.

STEP 2

Select Wired LAN or Wireless LAN then connect the LAN and set the configuration.

Decide depending on the LAN environment.

Wired LAN ............ Refer to “4. Wired LAN Configurations” (pp.27–34).

Wireless LAN ....... Refer to “5. Wireless LAN Configurations” (pp.35–44).

Detailed LAN configurations need to be done with a browser later. First, complete the Wired or Wireless LAN connection between computers and projectors, then start browser configurations. ➔ “6. Basic setting and operation” (pp.45–64).

STEP 3

Network Configuration has completed.

Follow each chapter to project an image and operate the projector.

■ Operate and manage the projector ➔ “7. Controlling the projector” (pp.65-86) ➔ “Power Control and status check” (p.66) ➔ “Controls” (p.68) ➔ “PC adjustment” (p.72) ➔ “Setting up the projector” (p.73) ➔ “Timer setting” (p.76) ➔ “Projector information” (p.79) ➔ “Multi-control” (p.81)

■ Project an image on the computer ➔ “8. Network capture functions" (pp.87-110) ➔ “Use of real time capture” (p.91) ➔ “Use of network communication” (p.96) ➔ “Moderator function” (p.107)

■ Project an image on a network server ➔ “9. Network Viewer functions” (pp.113-130) ➔ “Create the available data” (p.114). ➔ “Create the program files” (p.119). ➔ “Project the image with network viewer function” (p.124)

* Even if Network Capture 5 is not installed into the computer, the wireless LAN can be set up with USB memory. (p.95)

Installing the software

It is required to install the software into your computer to use the Network Capture function . Please install the software as follows.

Note: To install the software into the computer with Windows 2000, Windows XP or Windows

Vista, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise proper installation cannot be made.

Network Viewer & Capture 5 installation

1 Set the supplied Network Viewer & Capture 5 CD-ROM into the CD-ROM drive of your computer.

Double click SetupTool.exe icon in the "Tool" folder in the CD-ROM.

2 Select "English [United States]" from the pull-down menu on the "Choose Setup Language" window

and click OK button to start installing and then follow the installation wizards.

Installing the software

Chapter 2 Setup procedures

As the "License Agreement" will appear, read contents carefully and click Yes button if you agree to the license agreement to proceed with installing.

During the installation, following window may appear, click Continue Anyway button.

3 Click Finish to complete the installation.

Installed software

The following 3 softwares are installed on your computer.

● Network Capture 5:

Captures the displayed image and the sound of the computer and serves them to the projector via the network.

● Network Viewer 5 (File Converter 1):

Converts to the JPEG*1 data format which can be projected with the projector from the JPEG, bitmap and Power Point files.

● Network Viewer 5 (Program Editor) :

This is a tool to make the program which has a function to specify and order the projecting JPEG image data stored in the file servers.

* To uninstall these software, use "Add/Remove Program" from the control panel. *1 This product supports the JPEG image format. This file is needed to convert to the optimized JPEG file by using the

File Converter 1 software previously. Refer to the item "Creating the available data [Network Viewer 5]"(+p.114) about data converting for the projection.

Installing the software

Chapter 2 Setup procedures

File Converter 2 installation

1 Set the supplied Network Viewer & Capture 5 CD-

ROM into the CD-ROM drive of your computer. Double click SetupDrv.exe icon in the "Driver" folder in the CD-ROM.

2 Select "English [United States]" from the pull-down

menu on the language selection window and then click Install button to start installing.

Installed software and places

Network Viewer 5 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel".

● Network Viewer 5 (File Converter 2):

This is a kind of the printer driver to convert to the JPEG data optimized to project by the projector from any of the documents created by the application software.

* To uninstall Network Viewer 5 (File Converter 2), just delete the "Network Viewer 5(File Converter 2)" icon from the

"Printers and faxes" folder.

Chapter

3. Names and functions of the operation screen

This chapter describes the functions of each part of the operation screen.

Chapter 3 Names and functions of the operating screen

Turn on the projector and select either “Wired” or “Wireless” from the input menu of the projector. The “Please wait...” message will be displayed on the screen. After short time, the network connection standby display screen will appear as below. While the “Please wait...” message is shown, some operations are invalid.

Network connection standby display

Network Connection Standby Display

This software is to project the computer screen via the networks.

Select "All Programs" from the start menu --> Network Viewer & Capture 5" --> "Network Capture 5", then following screen will appear. Then the program will start.

Parts Names and Functions of the Screen

q Search PJ button Search the projector connected to the networks.

w Specify IP button

When connected to a different segment network, the projector can not be retrieved automatically.

In that case, press this button, the "Search specified IP address list" window appears, and then click Add button and enter the IP address directly to specify the projector in another window. The registered multiple IP addresses can be searched at a time.

e Wireless easy setting button / Wireless easy release button

Configure the Wireless LAN setting just by clicking this button. (The setting will be stored as AdHoc

system) For details, refer to "5. Wireless LAN configurations"-->"Easy wireless setting" (p.41). To restore the easy setting, press the Wireless easy release button.

r Network Projector List Display all the projectors connected to the networks. Show unoccupied projector as “On standby” and occupied projector as “Real time capturing” or "In

One-shot mode". When registered in a moderator’s group, "On Moderator mode" will be shown. The indication of the status of use with "#" indicates that your computer is now using the network capture function. After double-clicking on a projector name, the web browser gets activated and

the projector setup screen will be displayed.

Network Capture 5 window

q w

Network Capture 5 window

Chapter 3 Names and functions of the operating screen

t Start communication button

Enter the Communication mode, and then , the capture edit window starts. The selected projector

shows the capture edit window.

y Play Movie files button

The play movie files window will appear.

u Start real time capture button

Capture (Project) the computer screen in real time. After the execution of "Start real time capture",

the application window disappears. • • • v

i One-shot capture button

Copy and capture (project) the computer screen without modification. After the execution of One-

shot capture, the application window disappears. • • • v

o Terminate capture button

Terminate the real time capture and the One-shot capture. !0 Select capturing object button It is possible to designate the window to capture individually. This button is disabled by default,

so the full screen is captured. It is possible to change the capturing object function setting at

parameter settings. For detail, refer to "Parameter set up" (p.90). !1 Moderator registration button Register a computer user as a moderator. !2 Join moderator's group button Join the moderator's group which is selected in the Network Projector list. It is not available if there

is no moderator registered.

!3 Parameter setup button

Activate the parameter setup window, and execute the connections setting, the image setting, and

the moderator's function setting. For detail, refer to "Parameter set up" (p.90).

!4 Volume adjust slider and Mute check box

Adjust the audio output from the real time capturing computer. The mute check box is checked by

default.

v To show the application window again, refer to the item "Commands on the task bar" (p.89).

Using the multiple network adaptors

When your computer provides multiple network adaptors, the network adaptor selecting window will appear each time the Network Capture 5 software starts. Select a network adaptor and check the "Set network adaptor as default" and then click OK. To change the setting, refer to the item "Parameter set up" (p.90).

Note on Windows Vista

When you use the Network Capture 5 software with Windows Vista, the warning dialog "User account control" will appear. In that case, click Allow button to use it.

Chapter

4. Wired LAN configurations

This chapter describes the preparation for Wired LAN setting with projectors and how to set the LAN environment.

Chapter 4 Wired LAN configurations

Setting Procedure

Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately.

Connect the shielded LAN cable to the LAN connection terminal of the projector.

Network environment settings

Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “6. Basic setting and operation” (p45-64). First, complete the settings described in this chapter before performing steps in “6. Basic setting and operation.”

1. Turn on the projector and select “Network” from the input menu of the projector.

2. Select “LAN mode select” in the Network menu, and press Point 8 or SELECT button.

3. Select similar LAN environment among Wired1, 2 and 3 with the Point ed buttons. Then the Menu

will disappear, the “Please wait...” message will appear, and switching operation will start. Switching will take a while and after completing the operation, the “Ready for use” message will appear, and the projector’s LINK/ACT Lamp will be on or blink.

Connecting to the LAN line

LAN Connection Terminal

* When the LAN setting is “Off”, the two lamps will not be on.

ACT Lamp (Orange)

When the projector is connected to the 100 BaseTX network, light or blink as follows;

- Light when connecting to the network.

- Blink when sending or receiving the data.

LINK lamp (Green)

Light green when the projector is connected to the network.

LAN Cable**

** Please use a shielded LAN cable .

*1 Set "On" only when the DHCP server is available on your network environment. *2 Set [255.255.255.255] if the network does not provide the gateway (router). *3 Set [255.255.255.255] if you do not use the function E-mail alert. * While the network communication function (p.96) or moderator function (p.105) is to be executing, the menus

"Network capture", "Network viewer" and "Memory viewer" are displayed in gray.

Network environment setting

4. Select "Network setting" in the Network menu and press SELECT button, and then the LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings.

Move among the items with the Point

buttons and press SELECT button, move among the

columns with Point

7 8

buttons, a

djust the figures with Point ed buttons, and then press SELECT

button to set.

5. After completing all the settings, select “Set” and press SELECT button. Now, all procedures have been done. To cancel the adjusted settings, select "Cancel" and press SELECT button. To confirm whether the settings are correct, follow the procedures described from the next page. You can confirm the LAN settings you have made from “Network Information” (p.32). In such cases that the LAN cannot be connected, see this screen.

Network setting

DHCP: On

Item Description

DHCP .......................... Sets DHCP function On or Off. When you setup the network setting manually, select "Off".

When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your

network environment *1.

IP address .................Sets IP address of the projector

Subnet .......................Sets Subnet mask. Normally sets 255.255.255.0

Gateway*2 .................Sets IP address of the default gateway (Router)

DNS*3.......................... Sets IP address of the DNS server.

DHCP: Off

Chapter 4 Wired LAN configurations

Network Capture screen

Confirming the operation

Confirm that the projector has connected to the LAN properly.

Network Projector List

Search PJ button

1. Activate “Network Capture 5” which is installed into the computer connected to the LAN .

2. After “Searching projector” message appears, the name of the projector* appears on the Network Projector List, then the network setting has completed properly.

When the name of the projector does not appear and error screen appears, the network has

not connected yet. Try searching again with the Search PJ button. If error screen appears again, reconfirm the LAN setting. When the projector is set in the location separated by the router, see next page.

When Firewall function (Anti-virus software) is effective, network projector may not be found. In that

case, disable the Firewall function and try searching again.

✳ If the projector is named, the name will be displayed. The name can be set with the following

procedures in “6. Basic setting and operation” ➔ “Initial setting” (p50) . If the projector is not named, IP address of the projector will be displayed.

When set up the projector in the location separated by the router and the segment is different; Projector will not be found nor displayed. In that case, the projector needs to be searched directly by the IP address.

1. Press Specify IP button. "Search specified IP address" window appears.

2. Click Add button, "IP address set up" window appears. Enter the IP address of the projector and Click

OK button. Then, the projector will be added on the "Search specified IP address" window. Multiple projectors are registered and they are stored even when the application is closed.

3. Click OK button on the "Search specified IP address" window, the registered multiple projectors

will be searched. Then, the projector will be added on the Network Projector List of the application window.

"IP address set up" window

Specify IP button

Network Projector list

Confirming the operation

"Search specified IP address" window

Chapter 4 Wired LAN configurations

The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks.

Network PIN code

Network information

1. Select "Network PIN code" in the Network menu, and press SELECT button.

The Network PIN code screen will appear.

2. Set the Network PIN code.

Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons. Select “Set” and press SELECT button to set. To cancel the preset Network PIN code, select “Cancel”. When you do not want to set the Network PIN code, set 0000. It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See “6. Basic setting and operation” ➔ “Initial setting” ➔ “Network PIN code setting” (p51).

Select "Network information" in the Network menu and press Point 8 or SELECT button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what will be shown.)

Network PIN code

Network PIN code screen

Wired LAN factory default settings

Wired factory default

Select “Wired factory default” in the Network menu and press SELECT button. All the wired LAN settings will go back to the factory default settings. For details, refer to “Wired LAN factory default settings” (p.34).

Chapter 4 Wired LAN configurations

Wired LAN factory default settings

Parameter

SELECTED LAN

Wired 1 Wired 2 Wired 3

IP CONFIGURATION MANUAL DHCP MANUAL

IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100

SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0

GATEWAY ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255

DNS ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255

Chapter

This chapter describes the preparation for Wireless LAN setting with projectors and how to set the LAN environment. This projector contains the Wireless LAN module.

The setting procedures and configurations differ depending on the LAN installation location. Consult your system administrator for installation and set the LAN appropriately.

To operate via Wireless LAN, your computer has to be equipped with a Wireless LAN card adapter which supports IEEE 802.11b/g/n(DRAFT 2.0).

If connecting in Infrastructure mode with an access point, the access point is required to support IEEE

802.11b/g/n(DRAFT 2.0).

Caution: Do not use a mobile phone or PHS near

(within 20cm/8inch) the projector. It may cause malfunction.

5. Wireless LAN configurations

Chapter 5 Wireless LAN configurations

Setting procedures

1. Turn on the projector and select “Network” in the Input menu of the projector.

2. Select “LAN mode select” in the Network menu, and press Point 8 or SELECT button.

3. Select similar LAN environment among Wireless 4, Wireless 5 and Wireless Simple* with the Point

ed buttons. Then the Menu will disappear, the “Please wait...” message will appear, and switching operation will start. Switching will take a while and after completing the operation, the “Ready for use” message will appear.

For each settings, refer to "Wireless LAN factory default settings" on page 44.

✳ “SIMPLE” mode is used for simple setting without complicated LAN setting procedures to connect to

the Wireless LAN. See “Easy wireless setting” (p.41) for details.

The projector contains the Wireless LAN adapter. Set the Wireless LAN network through the projector menu. Detailed network settings will be made with browser. Refer to “6. Basic setting and operation”. ➔ "Network configuration" (p.53). Complete the settings described in this chapter before performing the steps in “6. Basic setting and operation.”

Setting the network environment

4. Select "Network setting" in the Network menu and press SELECT button, and then the LAN setting screen will appear and the selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator for the detailed settings.

Move among the items with the Point

buttons and press SELECT button, move among the

columns with Point

7 8

buttons, a

djust the figures with Point ed buttons, and then press SELECT

button to set.

When the network type is “AdHoc”, you do not have to change “Sub net” and “Gateway” and leave

them as default settings.

SSID/ESSID for the network type “Infrastructure” and “AdHoc” are required to be entered the same

characters into the projector, the access point, and the Wireless LAN compatible computer (up to 32 characters). Characters can be selected from A~Z, a~z, blank (space), 0–9, or - (hyphen) with the Point ed buttons. Move to the next character with the Point 7 8 buttons.

You can confirm that the projector settings from “Network Information” in the projector menu (p.42)

5. After completing all the settings, select “Set” and press SELECT button. Now, all procedures have been done. To cancel the adjusted settings, select the "Cancel" and press SELECT button.

To confirm whether the settings are correct, follow the procedures in “4. Wired LAN configurations” ➔ “Confirming the Operation” (p.30).

For configuring of WEP, WPA-PSK, WPA2-PSK security, select “Next”. Refer to “Configuring security with the projector” on next page for details.

Item Description

DHCP .......................... Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When

its set On, IP address, Subnet, Gateway and DNS are automatically set according to your network

environment *1.

IP address .................Sets IP address of the projector

Subnet .......................Sets Subnet mask. Normally sets 255.255.255.0

Gateway*2 .................Sets IP address of the default gateway (Router)

DNS*3.......................... Sets IP address of the DNS server. Must be set when the E-mail function is used.

Network type .......... Sets Infrastructure or AdHoc mode. When the "AdHoc" is selected, the security "WPA-PSK" and

"WPA2-PSK" are not available. SSID/ESSID

...................Identifier of the wireless access point.

"Network capture", "Network viewer" and "Memory viewer" are displayed in gray.

Setting the network environment

Network setting

DHCP: On DHCP: Off

Chapter 5 Wireless LAN configurations

Configuring security with the projector

Configure security with the projector by following the steps below. After configuring the network in “5. Wireless LAN Configurations” (p.35-44), select “Next” in the LAN setting screen and press SELECT button. The security configuration screen appears. Refer to “6. Basic setting and operation” ➔ “Configuring wireless LAN setting and security setting” (p.55) as well.

Use the Point ed buttons to select the security type. To disable the security, select “Disable.” Use the Point ed buttons to move among the items and adjust setting; use the Point 7 8 buttons to move among the character positions of the key entry fields.

This projector provides the following security options. Use optimum security option on your network environment.

WEP64(40)bit Open WEP64(40)bit Share WEP128(104)bit Open WEP128(104)bit Share WPA-PSK(TKIP) WPA2-PSK(AES)

Notes when entering characters:

The “¥” symbol is displayed as “\” when the ASCII key is used. The “]” symbol is treated as a character by the ASCII key, but it is not interpreted as a character by the HEX key. In HEX, the “]” symbol is displayed in red and setting is denied. You can not set all the characters with the “]” symbol. This will be considered as no operation.

ASCII key characters : Space - 0 to 9 A to Z a to z ! " # $ % & ' ( ) * + , . / : ; < = > ? @ [ ¥ ] ^ _ ` { | } ~ HEX key characters : 0 to 9 a to f

WEP configuration screen

Configuring security with the projector

Use of security type "WEP"

1. Use the Point ed buttons to select "WEP" security type.

2. Select “Key index”. Use the Point ed buttons to choose the HEX or ASCII key. The four (#1–#4) kinds of WEP keys can be configured. Use the Point 7 8 buttons to move to the right frame; use the Point ed buttons to select a WEP key number (#1–#4).

Refer the table below for the usable number of characters at the WEP security option.

WEP option Characters

WEP64(40)bit ASCII WEP64(40)bit HEX WEP128(104)bit ASCII WEP128(104)bit HEX

5 characters 10 characters 13 characters 26 characters

3. Use the Point ed buttons to select the Type field of the WEP key number that corresponds to the one you selected above and press SELECT button. The WEP key entry screen appears. In the WEP key entry field, all characters are displayed in “]”. Use the Point ed buttons to select a character; use the Point 7 8 buttons to select a character position. Enter all the characters displayed with “]”.

When you select HEX at WEP key index and the entry key contains “]”, the “]” symbol is displayed in red and setting is denied.

4. Use the Point ed buttons to select “Set” and press SELECT button to return to the Wireless setting screen. Select “Set” in the Wireless setting screen to complete the network setting.

WEP configuration screen

Chapter 5 Wireless LAN configurations

Use of security type "WPA-PSK", "WPA2-PSK"

1. Use the Point ed buttons to select "WPA-PSK" security type.

2. Use the Point ed buttons to select the key field and press SELECT button. The PSK key entry screen appears. Enter the PSK key by using the Point buttons. If the input PSK key has an error, the PSK key is indicated in red.

3. Use the Point ed buttons to select “Set” and press SELECT button to complete the network configuration, and return to the "Network setting" in the Network menu.

WPA-PSK(TKIP) configuration screen

Available PSK key characters

ASCII code ......8 to 63 digits

Hex code .........64 digits

* Security "WPA-PSK" and "WPA2-PSK" modes are not available when the "AdHoc" network type is selected. * When you set the PSK keys with 64 digits, the projector checks whether all of the entered PSK keys are in Hex code or

not. If any of the ASCII code is included in the entered PSK keys, the entered PSK keys are indicated in red as error.

Easy wireless setting

Error Screen

With this setting, you do not need any complicated LAN setting procedures. The network type will be AdHoc mode.

CAUTION: This function can be used only when logged in by Administrative right with Windows XP and Windows Vista, and cannot be used with Windows 2000. Windows XP should be Service Pack 1 or later version.

Setting Procedures

1. Turn on the projector and select “Network” in the Input menu of the projector.

2. Select “LAN mode select” in the Network menu, and press SELECT button.

3. Select “Wireless Simple” with the Point ed buttons. Press SELECT button then the “Please wait...”

message will appear and switching operation will start. Switching will take a while and after completing the operation the message “Ready for use” will appear. During the switching period, the projector cannot be operated. (“SIMPLE” LAN settings will be shown by pressing SELECT button. The settings cannot be changed.)

4. Activate “Network Capture 5” which is installed in the computer.

5. Click Wireless easy setting button on the operation screen. The Wireless LAN setting screen will appear and the computer will start to set up the Wireless LAN setting. (Adjust the computer’s Wireless LAN environment to the “SIMPLE” setting LAN environment.)

After completing the settings, the computer will start searching the projector which was set as

“SIMPLE” and will display the name of the projector or the IP address on the projector list.

Confirm whether the LAN has been set correctly and works properly. Refer to “4. Wired LAN

configurations” ➔ “Confirming the operation” (p.30) for the confirmation procedures.

If the network setup is not succeeded, the error screen will appear.

Wireless easy setting button

Setting screen

Easy wireless setting

Chapter 5 Wireless LAN configurations

Computer environment and Wireless LAN connection;

Wireless LAN with Wireless Easy setting connection will be made via AdHoc mode. For setting contents, refer to “Wireless LAN factory default settings” (p.44). With the Easy setting, computer’s LAN environment setting will be switched to the setup environment. Because of that, the LAN cannot work for the other operation while using “Network Capture 5”. After terminating the application or pressing the Wireless Easy Setting button, the LAN environment will automatically go back to the previous state.

Display the current LAN connecting environment. Select “Network Information” from the projector menu and press SELECT button.

Wireless factory default

Select “Network factory default”

in the Network menu

(p.33) and press SELECT button. All the wireless LAN settings will go back to the factory default settings. For details, refer to “Wireless LAN factory default settings” (p.44).

The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks. Select “Network PIN code” from the projector menu and press SELECT button. Set with the same procedures as setting Wired LAN Network PIN code. Refer to “4. Wired LAN Configurations” ➔ “Network PIN code” (p.32).

Network information

Network PIN code

Wireless Information (Example)

WIRELESS indicator display

When the wireless LAN configuration is set up correctly and the wireless communication is established with the access-point or computer in the network, the WIRELESS indicator on the front panel lights up. When sending or receiving of data, it blinks. Even though the wireless LAN in the network menu is selected, the WIRELESS indicator does not light, in this case, the wireless LAN configuration is not set up correctly, and please check the setting of the projector.

WIRELESS indicator

Chapter 5 Wireless LAN configurations

Easy wireless setting

Wireless LAN factory default settings

Factory default settings for Wireless 4, Wireless 5, and Wireless Simple as follows.

Setting Items

Selected LAN

Wireless 4 Wireless 5 Wireless Simple

IP CONFIGURATION MANUAL DHCP MANUAL

IP ADDRESS 169.254.100.100 192.168.100.100 169.254. * . *

SUBNETMASK 255.255.0.0 255.255.255.0 255.255.0.0

GATEWAY ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255

DNS ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255

WIRELESS CHANNEL

11 11

NETWORK TYPE 802.11b AdHoc INFRASTRUCTURE 802.11b AdHoc

WIRELESS SSID/ESSID

(SSID/ESSID)

PJ-WIRELESS5 ANY PJ-WIRELESS5

WEP

(WEP encryption)

DISABLE DISABLE DISABLE

WPA-PSK (PSK key)

DISABLE DISABLE DISABLE

WPA2-PSK

(PSK key)

DISABLE DISABLE DISABLE

Chapter

Describes basic operation and settings below by using the web browser.

• Initial setting Setup the basic setting such as Projector name, Network

PIN code, Time setting, etc.

• Network setting Configure Wired/Wireless LAN environment.

• E-mail Setting Configure E-mail function to manage the projector.

• SNMP Setting Configure SNMP function to manage the projector.

Caution: When operating the projector with the browser, connect the projector to the computer with Wired or Wireless LAN. Complete the connection in advance.

6. Basic setting and operation

Chapter 6 Basic setting and operation

1. Turn on the projector.

2. Start up the Network Capture 5. The Network Capture 5 searches projectors in the network and lists

up the IP address or projector name of the projector on the Network Projector List.

3. Double click the projector to set from the Network Projector List.

4. The web browser will start up and display the setting page of the projector.

Select a display mode and login

This product provides 2 types of control mode, Standard Mode and Light Mode as below. Select a proper mode to match your PC and network environment by clicking on the text link. Once you select your desired display mode, the setting page you selected display mode will be displayed automatically from the next login. To change the display mode, click "Top" on lower-right corner of the setting page (p.47).

STANDARD MODE For computer display, displays graphical

me nus and se tt in gs . Thi s mode is recommended for standard use.

LIGHT MODE Displays with 200 x 300 dots. This mode

is optimized for use of the handheld computer, PDA, etc. It is also convenient if the network traffic is heavy. (This mode has some limitations on the network viewer and multi-control functions.)

If the password has been set on the setting page, the authentication window will appear. In that case, type "user" onto the User Name text area and the login Network PIN code onto the Password text area and then click OK button.

* The entered User Name must be "user" and it can not be changed.

[Note] When the projector is accessed for the first time or the Network PIN code "0000" is set, the auto-login is performed and the next main setting page is displayed.

Starting up the Browser

Display of main setting page

The following main setting page will be displayed depending on your display mode selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages.

z Main setting page in the Standard Mode display

✐ This Standard mode display is mainly used through this manual for the setting and

control description.

✐ If your computer does not have the Adobe Flash

Player version 6 or later, follow the message on the control page to install the Adobe Flash Player. For further product information or installing, see the Adobe homepage.

http://www.adobe.com

Setting page

Displays the control and setting items according to the selected menu.

Ret ur ns to Dis pl ay Mode selection page (+ p.46)

Main menu

For selection of control and setting items of the projector.

Page numbers

Switches the pages by clicking the number's tab.

Sub menu tab

S wi tc h es th e s u b menu tab.

Clock display

Displ ay on or of f by clicking text ON or OFF

Starting up the browser

* To change the screen language, use the initial setting menu (p.50)

Chapter 6 Basic setting and operation

The network viewer function in the Light mode has following limitations;

- Cannot select the program or folder for the display.

- Cannot check up the images in the folder or program.

x Main setting page in the Light Mode display

How to use the setting page

To control and set up the projector, use the setting menus on the web browser. The basic operation and procedures commonly used on this manual are described below.

Main menu

Returns to the display mode selection page.

Setting page

The setting pallet appears after clicking the item. Change the value by clicking s or t button, or type the number onto the text box directly and then click Set button.

* Each item has a valid setting range respectively.

Example of the Setting Page

✐ The value in the text box indicates current value. ✐ Each item has a valid setting range. The setting value exceeding its range becomes invalid. Some control items can

not be used depending on the selected input mode or functions of the projector you use. In that case, the values of those items are indicated with "---".

Returns to main menu

✐ The blank page appears if your PDA does not provide a Adobe Flash

Player. You need to install the Adobe Flash Player. (+p.47)

Setting Pallet

Page numbers

Sub menu tab

Text box setting

Enter the number or text and then click Set button. or Ch an ge a val ue w it h s or t button and then click Set button. The value changes quickly when s or t button is kept pressing.

Pull-down menu setting

Selec t an item with pull -down menu button and then click Set button. or Select an item by clicking s or t button.

Radio button setting

Select an item by selecting a radio button

Check box setting

Select items by ticking on check boxes.

Type of the setting pallet

How to use the setting page

Chapter 6 Basic setting and operation

Initial setting

After installing the projector, perform the following basic initial setting. Click Initial Setting on the main menu to display the initial setting page.

Item Description

Language ................. Switches display language on the setting page. English or

Japanese.

Model name ............ Indicates the model name of the projector.

Projector name ....... Sets the name of projector. This projector name is listed on

the application window of the Network Capture software.

Network PIN code ...........

Sets the Network PIN code to login the setting page (+p.32,

p.42)

PJLink ......................... Switches PJLink password authentication on or off.

Password................... Password for PJLink function

Network PIN code setting

This is to set the Network PIN code to restrict the access from an unauthorized person through the network. Enter a 4-digit number as the Network PIN code onto the text box and click Set button. The projector's network part begins restarting and it takes about 20 seconds. Close (Quit) the web browser and access to the login page again in 20 seconds. This is to perform the login authentication firmly.

The default Network PIN code as [0000], which means no Network PIN code is set.

✐ When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four-

digit number is valid for the Network PIN code.

✐

If you forget the Network PIN code to the projector, you can check it by selecting "Network PIN code" sub menu from "Network" menu on the projector. For further information, please see item "Network PIN code setting" (+p.32, p.42).

PJLink and password setting

This is to set the PJLink password authentication on or off. If "On" is set with the PJLink pull-down menu, the password must be required. Enter a password* onto the text box and click Set button. Refer to the projector owner's manual for further details of the PJLink function.

✐ 1 to 32 alphanumeric characters can be used for the password.

What's PJLink?

The projectors equipped with PJLink function can be used together on the same network, regardless of model or brand, for centralized control and monitoring. This standard was established by the Japan Business Machine and Information System Industries Association (JBMIA). http://pjlink.jbmia.or.jp/

Initial setting

Chapter 6 Basic setting and operation

This projector does not provide the built-in battery. The date and time information are lost when the projector turns off ( when "Eco" is set for the stand-by mode (Refer to p.74)), or the network configuration is reset. The timer function is disable until time is set up correctly. When using the NTP address for time setting, the current time is acquired at the projector starting up and the timer function is activated after finishing the time setting correctly.

Item Description

NTP address ............. Enter the address of NTP server. Please consult your

network administrator for setting up of the NTP server.

Time zone .................Sets your country or region's time zone

Temperature ............ Switches display temperature unit Centigrade or

Fahrenheit

Time setting ............. When clicking AUTO button, the date and time set on

your computer are set to the projector. The timer icon

appears when time is set up correctly.

Current time ............ Indicates current date and time set on the projector

Date ............................Sets date in manual

Time ............................Sets time in manual

Date and time setting

NTP is abbreviated expressions of Network Time Protocol. It is a protocol to acquire the exact current time via the network. This projector acquires the current time from the NTP server and update the time in the network module. After setting the NTP address, the projector acquires the time per 24 hours. If the projector fails acquiring the time from the NTP server, the projector tries to acquire the time every 1 hour until it succeeds.

✐ "Time zone" is the local time as an offset from Greenwich Mean Time (GMT). "Time zone" is in ± hour:minute

format and is available from -23:59 to +23:59. ex. Time zone: +09:00 in Tokyo, Japan ✐ Both of "NTP address" and "Time zone" should be set, otherwise the setting will be failed.

When the NTP address is not set, perform the time setting with "Auto-setting" or "manual setting" described below.

Auto setting

Click AUTO button on the page, the date and time set on your computer are set to the projector.

Note: Confirm that your computer has a correct clock time before performing the

auto time setting.

Manual setting

Click the item Date or Time and enter the date or time on the input box with adequate format. Date is in year/month/day format. ex. 2007/10/05 Time is in 24-hour:minute format. ex. 18:30

Network configuration

Click Network on the main menu. The following setting page is displayed. Set up the projector's network environment on this Setting sub menu.

Setting of LAN

1. Select a type of LAN from Change setting pull down menu. LAN1(Wired) LAN2(Wired) LAN3(Wired) LAN4(Wireless) LAN5(Wireless) Simple(Wireless)

For the default setting of the above LAN, see the items "Factory Default Setting".

*1 Set [255.255.255.255] if the network does not provide the gateway (router). *2 Set [255.255.255.255] if you do not use the function E-mail alert.

Item Description

Change setting .......Selects LAN1 to LAN5 and Simple

IP configuration......Sets DHCP or Manual

IP address .................Sets IP address of the projector

Subnet mask............Sets Subnet mask.

Default gateway*1...........Sets IP address of the default gateway (Router)

DNS*2.......................... Sets IP address of the DNS server.

Network configuration

Chapter 6 Basic setting and operation

2. Select either "Manual" or "DHCP" from IP configuration pull down menu. When "DHCP" is selected, IP address, Subnet mask, Default Gateway, DNS are automatically configured by DHCP function. Only the DNS address allows you to set up manually if the DNS address information is not provided on your DHCP server. When selecting "Manual", configure all the items manually. For further information, contact your network

administrator. The address must be entered as 4 number groups separated by a dot like [192.168.001.101].

3. After completing the network configuration, press Set button to register the network information. The Simple(Wireless) setting is fixed, which cannot be changed from factory default value.

4. To apply the setting, press Set button. The network of the

projector starts re-booting and applies the setting. It takes about 20 seconds to complete. Close the web browser and access to the login page again in 20 seconds.

On the screen of the projector, the “Please wait...” message will appear and switching operation will start. Switching will take a while and after completing the operation, the “Ready for use” message will appear. During the switching period, the projector cannot be operated.

When you use LAN4(Wireless) or LAN5(Wireless), the setting items of page [2] and [3] are activated and you can setup Wireless LAN setting and Security setting. See the item " Configuring Wireless LAN Setting and Security Setting" for further setting.

✐ When the IP address collides with the address of other equipment, the computer cannot communicate with the

projector. When the IP address collides with the address of other equipment, the computer cannot communicate with the projector. Set an IP address again after selecting another LAN mode from "Change setting" or turning off and then on the projector.

Configuring wireless LAN setting and security setting

Configure the wireless LAN setting and security setting for Wireless 4 and Wireless 5.

Configuring wireless LAN setting

1. Click page [2] of setting pages. Following wireless LAN setting can be done. After completing the configuration, press Set button.

Item Description

Wireless Mode ........Select the Communication standard 802.11b or 802.11b/g/n.

Network Type. ......... Select either “Infrastructure” or “AdHoc”. When selecting the "AdHoc", the security

"WPA-PSK" and "WPA2-PSK" mode are not available.

SSID/ESSID ...............Set the SSID/ESSID. (up to ASCII 32 characters)

SSID/ESSID is case-sensitive. Even though all characters on the Wireless

information is uppercase, it is necessary to distinguish between upper case and

lower case characters.

Channel .....................I f you use the projector in 802.11AdHoc mode, select the channel, from 1 to 11.

Configuring wireless LAN setting and security setting

Notes for entering characters:

Chapter 6 Basic setting and operation

Configuring wireless LAN security setting

Click page [3] of setting pages. Following wireless LAN security setting can be done. After completing the configuration, press

Set button.

Item Description

Network security ...Sets the type of encryption. Following types are available. WEP64(40)bit Open WEP64(40)bit Share WEP128(104)bit Open WEP128(104)bit Share WPA-PSK(TKIP) WPA2-PSK(AES)

Input type.................ASCII or HEX. See item "Notes for entering characters"

Key index1 - 4..........Enter keys of encryption.

The used number of character changes as the table below according to the type of WEP

encryption and input type.

WEP option Characters

WEP64(40)bit ASCII WEP64(40)bit HEX WEP128(104)bit ASCII WEP128(104)bit HEX

5 characters 10 characters 13 characters 26 characters

Four key indexes can be set, however, the only one with check on its radio button is

effective. Both of the number and value of the key index in effect must be same as those

of your computer and the access point. Depending on computers and access points, you may be allowed to select only one WEP key. In that case, use key index1.

PSK ..............................Available when the "WPA-PSK(TKIP)" or "WPA2-PSK(AES)" is selected.

The PSK key must be no fewer than 8, nor more than 63 digits with ASCII code, and 64

digits with Hex code.

E-mail setting

This product has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps.

Item Description

SMTP server*1 ..........

Sets server name or IP address of the SMTP server Administrator

address ......................Sets E-mail address of administrator

Add e-mail

address ...................... Sets E-mail address of the user to send a mail when the

projector has an abnormality.

1 Setting SMTP server and administrator address

Set the server name or IP address of the SMTP server*1 and administrator address. The administrator address is set to "Reply-To" address of the message sent from the projector.

*1 The SMTP server is a server for sending E-mail. Please contact your network administrator to have this SMTP

server address. When the server name for SMTP server is used, DNS must be set up to activate the E-mail function.

(+p.53)

✐ If the projector sends an alert message due to the abnormality on the projector but the SMTP server is down in

some other reason, the message will not be sent. In that case, the message "Unable to connect to server." will be displayed on the setting page. To clear this message, set up SMTP server address again.

✐ To use the E-mail function, it must be set the DNS address on the Network setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send

e-mails to the administrator address, enter the administrator address into "Add e-mail address" text box.

E-mail setting

Chapter 6 Basic setting and operation

2 Registering and deleting E-mail addresses

Click "Add E-mail address" and type the E-mail address onto the text box and click Set button. To check the registered addresses, click Check/Delete sub menu tab. The addresses are listed as the figure on the right.

✐ Up to 10 E-mail addresses can be registered.

To delete the registered addresses, check the address you want to delete and click Delete button.

3 Option selection for sending alert mail

Click Option sub menu tab. Check the condition items under which alert mail will be sent and click Set button.

Please refer to the item "Examples :Type and contents of alert mail" described on the next page.

Check / Delete

Option

[1]––––––––––––––––––––––––––––––––––

o When PJ lamp is off. o When PJ lamp replacement time is reached. o When internal PJ power circuit is failed. o When internal PJ temperature is too high. o When PJ is turned into Standby in proper user

operation.

[2]––––––––––––––––––––––––––––––––––

o When accumulated filter use time reaches

[ ] hours.

o When Power management function turns PJ

lamp off.

o When the signal is interrupted. o When Auto Play is failed.

[3]––––––––––––––––––––––––––––––––––

o When lamp Corres. Value reaches

[ ] hours. Attached message

✐ "When PJ lamp is off" signifies the lamp goes out

without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY

button on the top control or the remote control.

✐

If condition "When Auto Play is failed" is checked, the trap is sent when the error occurs during the auto display operation using with the network viewer function (+p.113). For further information of the error, refer to item "Auto Display setting and control page [3]"(+p.128).

✐ The length of message should be less than 255

characters.

✐ Up to 99,999 hours can be set for use time.

✐

The optional settings return to the factory default when you unplug the AC power cord of the projector.

Examples: Type and contents of alert mail

When the projector has an abnormality, the following alert messages are sent to the registered E-mail address depending on your selected condition. Administrator or user can take an efficient action quickly by receiving this message. This is very useful to maintain and service the projector. The following are examples of received messages.

● When internal PJ temperature is too high:

✐ The projector let users know the information which thermal sensors inside the projector detected the

abnormal temperature risen and so the projector was turned off. Please refer to item "Power control and status check" (+ p.66) for the location of the sensors and each temperature . Also see the owner's manual of the projector for further details.

TITLE: Message from projector 10-03-2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

* The Projector lamp is turned off, because internal Projector temperature is too high. Wait for the completion of the cooling process and make sure the projector has been turned into Standby. Then turn the projector on again. If the Indicator continues flashing, check the air filter for dust accumulation.

[A] 81.5 degrees fahrenheit [B] 134 degrees fahrenheit [C] 95.6 degrees fahrenheit Temperature of Sensor B is too high.

● When internal PJ power circuit is failed:

TITLE: Message from projector 10-03-2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The Projector lamp is turned off, because Projector power circuit is failed. Unplug the Projector from AC outlet and ask servicing to qualified service personnel.

MAIN, P-FAIL OK MAIN, 1.8V OK MCI, P-FAIL NG

✐ The projector detects the power failure. Unplug the AC power cord and plug it again, and then turn on the

projector to verify the operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel.

Error information

E-mail setting

Chapter 6 Basic setting and operation

✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without

resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This alert mail will not be sent when the mail sending condition "When the life span of lamp is reached" is unchecked.

● When lamp corres. value reaches preselect use time:

✐ The projector sends a free message when the lamp use time (Corresponding value) reaches the

preselected lamp use time. It can be used for preparation of the lamp replacement and the maintenance required.

TITLE: Message from projector 10-03-2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The accumulated lamp use time reaches 1800 hours. Prepare for the lamp replacement.

Discretional messages

● When PJ lamp replacement time is reached:

TITLE: Message from projector 10-03-2007 00:59 Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The PJ lamp replace time is reached.

✐ The SNMP agent provided with this product is based upon MIB-2 defined by RFC1213. For private MIB

information, refer to file "Mibinfo/XUPjNet.mib" in the CD-ROM.

SNMP setting

This product provides a SNMP (Simple Network Management Protocol) agent function. The SNMP consists of a manager and agents. The group which exchanges

information with SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (read- write). This product allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item.

Item Description

Contact ..................... Enter user name of the projector etc. (optional)

Place...........................Enter place of the projector (optional)

Community

name(refer) ............. Enter community name (read only). Default name is

"public".

PJ information

SNMP setting

Chapter 6 Basic setting and operation

Item Description

Community name ........... Enter community name to send "Trap". Default name is

"public".

Trap address ............ Enter IP address of the SNMP manager computer to

receive "Trap". Up to 10 address can be registered.

✐ Up to 10 trap addresses can be registered.

Trap

Check and delete the trap address

Checking the registered trap address and deleting the address. To delete the address, tick the check box in front of the IP address and click Delete button.

Trap check/delete

✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user

operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/ STANDBY button on the top control or the remote control.

✐ Up to 99,999 hours can be set for the time setting.

✐

Trap option

Trap option setting

Tick the check boxes in front of the condition item to send the trap.

✐ Click Set button if you tick or un-tick the check box on a page.

[1]––––––––––––––––––––––––––––––––––

o When PJ lamp is off. o When PJ lamp replacement time is reached. o When internal PJ power circuit is failed. o When internal PJ temperature is too high.

[2]––––––––––––––––––––––––––––––––––

o When PJ is turned into Standby in proper user

operation.

o When accumulated filter use time

reaches [ ] hours.

o When Power management function turns PJ

lamp off.

[3]––––––––––––––––––––––––––––––––––

o When the signal is interrupted. o When Auto Play is failed. o When lamp Corres. Value

reaches [ ] hours.

SNMP setting

Chapter 6 Basic setting and operation

Chapter

Describes controlling and setting of the projector by using the web browser.

7. Controlling the projector

Chapter 7 Controlling the projector

Power control and status check

Click Power & Status on the main menu. The control page will be displayed. By clicking ON or Standby button on the page, the power of the projector can be controlled.

Item Description

PJ status

Power ............................ Displays the status of the lamp. (ON, OFF, On starting up, On cooling down)

Status ............................ Displays the status of the projector's power. (Refer to next page.)

Power control .............. Controls the projector power by clicking the "ON" or "Standby" button.

PJ temp.

Inside temp.A ............. Displays the surrounding temperature of lamp in the projector.

Inside temp.B .............Displays the surrounding temperature of panel in the projector.

External temp. ............Displays the surrounding temperature of the intake vent.

.......... The warning icon will appear if the temperature exceeds a specified value. Check if there

is no object to obstruct the airflow around the intake or exhaust vent. It might be airfilter clogged. Clean up the airfilter.

* The temperature unit can be set either Centigrade or Fahrenheit in the item "Initial

Setting". (+p.52)

Popup confirmation window

Confir mati on wi ndow as shown in the below appears when the Standby button is pressed.

✐ The projector cannot be turned on while the projector is cooling down. ✐ The web browser checks and updates the projector's condition every 30 seconds automatically.

About projector condition

Status Description

Normal ..................................................................Projector is operating normally.

Power management in operation

......................Power management is operating

Lamp failure........................................................Lamp failure is occurring

Abnormal Temperature ..................................The temperature of the projector became too high

Cooling down after abnormal Temp.

Projector detects abnormal temp. and is cooling down itself.

Standby after Abnormal Temp. ................... Projector detects abnormal temp. and is set into standby mode.

Power failure ..................................................... Power failure has occurred inside the projector. Projector is turned off.

Unplug the AC cord and contact a qualified service personnel for service. If the power failure occurs on the projector, "Power failure" is indicated on

the status column and the information icon appears on the power column

as shown below. Click this icon to display further information of the power

failure.

When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control the projector through the network, unlock the security on the projector using with the projector's menu control.

Click this icon to display further information of the power failure.

Power control and status check

Caution about turning on/off the projector via the networks

When turning on/off the projector via the networks, preset the projector as follows:

1. Select “Setting” from the Projector menu.

2. Select “Standby mode” from the Setting menu and set it as “Normal”. If you set this function as Normal, the network part of the projector is constantly provided with power even if the projector is turned off. If you set this as Eco, then the network part will be turned off when you turn off the projector. Consequently, you cannot turn on/off the projector via the networks.

Chapter 7 Controlling the projector

Controls

Click Control on the main menu. The setting method differs depending on the contents of the page. Click on the page number to change pages and select desired setting items.

✐ Please see the owner's manual of the projector to have the further informa-

tion of each control item.

✐ The control page displays valid control items depending on the selected input mode, signal or functions of the

projector you use, therefore, there may be different controls between the described items and actual control items on the page display. For further information , refer to the projector's owner's manual.

✐

When the projector is standby, only the timer on the setting menu is available; others are not available.

Item Description

Input ........................... Selects input mode of the projector.

Source ........................ Selects signal source of the input.

Computer1 : RGB Component RGB(Scart) Computer2 : RGB(PC analog) HDMI : HDMI Video : Video S-video : S-video Network : Network

Input

This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode.

System

This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button.

✐ If the modes (Mode1 to Mode5) stored in the item "PC Adjustment" (+ p.72) are available, they are also listed

together with the above mode.

Controls

Available selection at the RGB(PC analog) input

Item Description

XGA1 .......................... It automatically switches to the proper computer

system of the input signal.

* The computer system modes (VGA, SVGA, XGA.

SXGA, UXGA, WXGA...) which meet the input signal listed.

Available selection at the Video/S-video/Scart input

Item Description

AUTO .......................... It automatically switches to the proper color system of

the input signal.

* The selectable color systems are PAL, SECAM, NTSC,

NTSC4.43, PAL-M and PAL-N.

* AUTO is fixed at the Scart input.

Available selection at HDMI input

Item Description

D-480p ....................... It automatically switches to the proper scanning

system of the input signal.

* The selectable scanning systems are D-480i, D-575i,

D-480p, D-575p, D-720p, D-1080i and D-1080p.

D-XGA ........................ It automatically switches to the proper computer

system of the input signal.

* The computer system modes (D-VGA, D-SVGA,

D-XGA. D-SXGA1...) which meet the input signal listed.

Available selection at the Component input

Item Description

AUTO .......................... It automatically switches to the proper scanning

system of the input signal.

* The selectable scanning systems are 480i, 575i, 480p,

575p, 720p, 1035i and 1080i.

Chapter 7 Controlling the projector

Item Description

Contrast.....................Adjusts picture contrast

Brightness ................Adjusts picture brightness

Color ...........................Adjusts picture color saturation

Tint ..............................Adjusts picture hue

Image adjustment

This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button.

Item Description

Color temp. ..............

Sets a color temperature mode. White balance Red, Green,

Blue ...................... Adjusts each white balance respectively.

Sharpness .................Adjusts picture sharpness.

* When the value of the white balance is changed, the color temp. indicates

"Adj."

Item Description

Gamma ........................

Adjusts brightness of darker part of the picture. Noise reduction

....... Switches noise reduction mode

Progressive

.................. Switches progressive mode

Reset ...........................Resets the Image adjustment to previous levels.

Store ........................... Stores the Image adjustment values. Select an item

[Image 1 - Image 4] from the pull-down menu and click

Store button.

Load ............................ Loads the Image mode.

Select an image mode from

the pull-down menu and

click Load button. There

may not be available mode

depending on the input

mode as shown in the table

left.

Input source

Image mode Video Computer

Dynamic

4 4 Standard 4 4 Real * 4 Cinema 4 * Blackboard(Green) 4 4 Colorboard 4 4 Image 1 - 4 4 4

✐ The mark "4" indicates the available image mode in the selected input

source. The error message appears when the disabled image mode indicated with "*" is selected.

Sound

This function is to adjust the sound of the projector. The values in the text box represent the current control value or status.

Item Description

Volume ...................... Adjusts the sound volume from the speakers.

Mute ........................... Suppresses the sound.

Controls

Chapter 7 Controlling the projector

PC adjustment

Click PC Adj. on the main menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen.

Item Description

Current mode ...........

Displays a current mode like VGA, SVGA, XGA, SXGA, UXGA, WXGA, etc. or MODE1 - MODE5 are the customized mode

created by using the "Mode Store" function described below.

Auto PC adj. ............. Performs automatic adjustment.

Fine sync. .................. Performs Fine Sync adjustment.

Total dots .................. Adjust the number of total dots in the horizontal period.

Clamp.........................Adjusts the phase of the clamp.

Display area

Horizontal ...............

Adjusts the image area horizontally.

Vertical .................

Adjusts the image area vertically.

Item Description

Position

Horizontal ........... Adjusts the horizontal position of the screen.

Vertical .................

Adjusts the vertical position of the screen.

Reset ........................... Resets the PC adjustments to the previous levels.

Mode Store .............. Stores the PC adjustment values. Select a mode no.

[Mode1 - Mode5] from the pull-down menu.

Mode Free ................ Clear the PC adjustment values. Select a mode no.

[Mode1 - Mode5] from the pull-down menu.

Setting up the projector

Click Setting on the main menu. This function is to set up the projector. Select the sub menu [Screen setting], [Setting 1] or , [Setting 2] and then set up each setting.

Item Description

Screen ........................ Switches the screen mode. There may not be available

mode depending on the input mode as shown in the table below.

Input source

Screen mode Video Computer

Normal

4 4 True * 4 Full 4 4 Zoom 4 * Wide 4 * Natural wide 4 * Custom 4 4

✐ The mark "4" indicates the available screen mode in the selected input

source system. The error message appears when the disabled screen mode indicated with "*" is selected.

Setting up the projector

Chapter 7 Controlling the projector

Item Description

Language ................. Sets the language display of projector's on-screen

display menu.

Auto setup ............... Executes the Auto PC Adj, and Input Search function

below according to the each setting after clicking Start

button.

Auto PC adj. ........Sets Auto PC Adjustment mode.

Input search .......Sets the auto-input signal detection mode.

Auto keystone ...Sets Auto Keystone mode.

Background ............. Sets the screen background when no signal input.

Item Description

Power

management .......... Sets into the selected power management mode if the

input signal is interrupted and no control key is pressed

for the specified period of time. * The specified time can be set 1 to 30 min.

On start ..................... Sets the power-on mode when the AC cord is

connected to the outlet.

Standby mode ........ Sets the network function enable or disable in the

standby mode.

Normal .....Enable

Eco ............Disable

Lamp control ........... Selects the lamp control mode.

Remote control

.......... Sets the remote control code.

Item Description

Display ....................... Switches on or off the on-screen menu display on the

screen.

Countdown off ....Displays image during the starting up.

Logo ........................... Sets the logo display on the screen during the startup.

Ceiling ........................ Sets the image top/bottom and left/right reversed.

Rear ............................. Sets the image left/right reversed.

HDMI setup .............. Sets the input signal form of HDMI input.

Image. ...................Sets the Digital R/G/B image level of HDMI.

Sound ...................Sets the audio input when using HDMI.

Item Description

Terminal .................... Sets the terminal of "COMPUTER IN 2/MONITOR OUT".

Pointer ....................... Sets the pointer form.

Picture in Picture .... Sets the Picture in Picture mode and set the sub picture

size and position.

Mode ...................... Sets the Picture in Picture mode.

Subpicture size ... Sets the sub picture size.

Subpicture position

.. Sets the sub picture position.

Setting up the projector

Item Description

Factory default ................ Sets all of the projector control items to the factory

default setting except the following items.

Lamp Corres. Value, PJ time, Filter time, PIN code lock

and Logo PIN code lock.

No show .................... Sets the black out image temporarily.

Freeze......................... Sets the image to freeze mode.

P-Timer ......................Switches the P-Timer display.

ON .......... Starts P-Timer indication

STOP ...... Stops P-Timer counting

OFF ........ Stops P-Timer indication

Item Description

Lamp Corres. value

... Displays the use time (Corresponding value) of the

lamp and reset the counter.

Filter counter ........... Displays the filter use time. Reset the time after filter

clean-up.

Filter warning .......... Sets the time to indicate the filter warning message

on the screen.

Item Description

Key lock ..................... Sets the prohibition of controls either Projector or

Remote control.

Closed caption ........ Sets the closed caption function.

Closed caption .. Sets the closed caption mode. (OFF/CC1/CC2/CC3/

CC4)

Color ..................... Sets the color of the contents. (Color/White)

Fan .............................. Sets the cooling options after turning off.

L1 Normal cooling L2 Silent cooling

Fan control ..............Sets the fan control speed.

Off Normal mode On1 Highland mode 1 On2 Highland mode 2 On3 fan speed Max mode

Chapter 7 Controlling the projector

How to set the timer

1 Set a day or date

To set the timer event at the same time everyday or every week,

Select day entry with radio button and then select desired day from the pull-down menu button. The selectable days are as follows:

- Same time everyday - Every week (days from Monday to Sunday)

To set the timer event on specified date,

select date entry with radio button and then type the date with (Year/Month/Date) format.

Ex.: Type [2007/12/20] if you specify [December 20, 2007].

Timer setting

This page is to set the timer to turn the projector off or on at a programmed day/date and time. Follow the steps below for setting. Click Timer on the main menu.

Present time set on the projector

Select date

Select day

Set execute time

Event action

This projector does not provide the built-in battery. The date and time information are lost when the projector turns off (when "Eco" is set for the stand-by mode (Refer to p.74)), or the network configuration is reset. The timer function is disable until time is set up correctly. When using the NTP address for time setting, the current time is acquired at the projector starting up and the timer function is activated after finishing the time setting correctly.

"---" will appear on the current time when the time is not set up correctly.

2 Set an execute time

Type the time with (Hour:Minute) and 24 hours format.

Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes].

3 Select an event action

Select an event action from the pull-down menu.

Event Action

ON .................................. Turns on the projector

OFF ................................Turns off the projector

Lamp Auto .................. Changes lamp mode to "Auto"

Lamp High ..................Changes lamp mode to "High"

Lamp Normal ............. Changes lamp mode to "Normal"

Lamp Eco .....................Changes lamp mode to "Eco"

4 Register an event

Click Set button to register the set timer event. Repeat steps 1 to 4 for another timer event setting.

Change the event mode

On the event list appearing by clicking Check button, click on the event you want to delete, disable or enable. Click Cancel, Delete, Timer ON or Timer OFF button on the popup pallet.

Check the timer events

To check the set timer events, click Check button. The timer events are listed. The event with blue background color represents the timer-OFF event.

Button Operation

Cancel ........................Cancels the setting

Delete ........................Deletes the timer event

Timer OFF .................Disable the timer event temporarily

Timer ON...................Enable the timer event

Timer setting

Chapter 7 Controlling the projector

Notes on timer setting

✐ Up to 10 timer events can be registered. Timer events always operate according to the next valid event depending

on the projector's power status. In the example below, event 3 turns on the projector so next event 4 (also turning on projector) will not be effective because the projector is already turned on. Similarly, when the projector is turned off by event 5, event 6 OFF will not be effective in turning it off again. But these secondary events (event 4 and event 6) will become effective if a person turns off the projector (after event 3 and before event 4) or turns on the projector (after event 5 and before event 6).

Event 1 ON Event 2

OFF

Event 3

Event 4

Event 5

OFF

Event 6

OFF

Projector Power

OFF OFF OFF

Invalid event Invalid event

Time

✐ When the timer events are set at the same time, the last event set will override the previous events. For example,

if there is an event like "ON at 8:00 everyday" and then new event is set like "OFF at 8:00 everyday", only the last setting event is effective.

✐ When the timer event ON occurs during cooling down period, this is invalid event because the projector cannot be

turned on during that cooling down period.

Projector information

This page is to display the basic information of the projector status. Click

Information on the main menu.

Items Description

Input ...........................Displays selected input and source.

System .......................Displays selected signal system.

Signal .........................Input signal status

Screen ........................Displays screen mode.

Lamp status

.............. Displays lamp status with an animation. Refer to the

table on the next page.

Security .....................

Displays the security (PIN code lock) status

Click this button to update the information

Projector information

Chapter 7 Controlling the projector

Icon di splay/background Status

White-Yellow/Blue Lamp on (Normal)

White-Yellow/Red

Lamp on (Lamp is being used over a specified use time, replace lamp immediately)

Gray/Blue

Lamp off (Normal)

Gray/Red

Lamp off (Lamp is being used over a specified use time, replace lamp immediately)

Red/Blue with X

Lamp failure (Lamp failure, check the lamp condition)

Red/Red with X

Lamp failure (Lamp failure and lamp is being used over a specified use time, replace the lamp immediately)

Indication of the lamp status

Items Description

PJ time .......................

Displays the accumulated use time of the projector. Lamp Corres.

Value .......................... Displays the use time (Corresponding value) of the

lamp.

Filter time .................

Displays the use time of the filter.

Timer ..........................Displays the timer setting status.

ON Timer has been set. OFF No timer setting.

Multi-control

Controlling and setting the multi-projectors

When you install multiple projectors in the network, you can control and set up them together. Click Multi Control on the main menu to display the control page.

Note:

To control the multiple projectors, each projector must be set the same Network PIN code.

PC6

PC4

PC5

Select Input2 for PJ1 to PJ4.

PJ3PJ1 PJ2 PJ4

Example of multi control

Multi-control

Chapter 7 Controlling the projector

Start/stop the multi control

To start or stop controlling the multi-projectors, click Multi control setting menu and select ON or OFF.

Multi control setting

OFF ..........Stops multi control function

ON ............ Starts multi control function. The multi control

menu will appear when ON is set. These items of menu are linked to the main menu.

The multi controllable menus are "Power & Status", "PC adjustment", "Control", "Setting", "E-mail setting", "Timer", "SNMP setting" and "Network Viewer". Click each menu and perform setting and adjustment.

✐ The word "MULTI CONTROL" appears on the each control page while

the multi control is operating.

This shows the multi control is operating now.

Switches on and off the multi-control function

To use the multi control function, register the IP address of the projector you intend to control. Click Pj registration sub menu tab and set the IP address, Memo and Multi control item, then click Set button.

✐ 10 projectors can be registered per page and up to 100 sets can be registered for the multi-control.

IP address

Page no.

Click here to close

the sub menu Check & Change.

* When you click on a listed IP address, the

Items Description

IP address .................Enter IP address of the projector to control

Memo.........................Enter projector name or installed location etc.

Multi control item

Control ................. Controlling the projector

Control & Image ........ Controlling and displaying images

Image.................... Displaying the images

Status

Confirmation of registered projector

To check the registered information, click Check & Change sub menu tab. The registered information of the projector is listed as the below.

* The word "none" is displayed if the "Memo" function is used.

Memo

Multi-control

Chapter 7 Controlling the projector

Status

If some of the reg ist ered projec to rs are di sable d by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still active. At the same time, the deactivated projectors are excluded from the multi-control. The status of the registered projectors are indicated under the projector name. See the table below for status indications.

✐ If the multi-controlled projector is in the standby mode, items of "PC adj.", "Control" and "Setting" cannot be

operated.

✐ Cannot register, delete or change the multi-control setting during using the network viewer function. ✐ It is recommended that a specified projector should be chosen for setting as a master when you use this multi-

control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector.

✐ If the registered projector is not connected to the network, it will take a while to complete the multi-control

operation because of waiting for the response from each registered projector.

✐ There are some disabled items in the multi-control function for the light mode.

Change the mode of the registered projector

To change the mode of the registered projector, select a mode with the pull-down menu button under the IP address of the target projector and then click Set button.

Status Description

(blank) ........................ The projector is connected to the network correctly

No connect .............. The projector may not be connected to the network. Please check the connection and network

configuration of this projector.

PIN code error ................. The PIN code is incorrect. The PIN code for the multi-controlled projectors must be the same.

Change the PIN code of this projector to the common PIN code. (p.32, p.42)

File Error .................... Not displaying the images. Check if this projector is using the Network Capture function or

Network Viewer function individually, or in the standby mode.

* The projector updates the status at the time when the multi-control function is executed.

Mode Operation

Control ....................... Controlling the projector

Control & Image .............. Controlling and displaying images

Image ......................... Displaying the images

OFF.............................. Excluding from the multi-control

Delete ........................ Deleting from the multi-control

Status

* The multi control item is not changed during using the network

viewer function. It is not available with the light mode.

Check & Change page in the light mode

Following functions in the "Check & Change" page are not available in the light mode.

- Changing the control mode.

- Deleting the registered IP address

- Indicating the each status

- Indicating the each memo

Controlling all together

"Power & Status", "PC adjustment", "Control" and "Setting" can be controlled all together. Set "ON" the multi control setting and adjust controls of each menu. The setting value is applied to the registered projectors sequentially .

✐ This is effective only if the multi control item of the registered projector is

set to either "Control & Image" or "Control".

Setting all together

"E-mail setting", "SNMP setting" and "Timer" can be set all together. Set "ON" the multi control setting and items of each menu. The setting value is applied to the registered projectors sequentially.

✐ This is effective only if the multi control item of the registered projector is

set to either "Control & Image" or "Control".

(Check & Change page in the light mode)

This indicates that the mode is "Image".

This indicates that the mode is "Control".

Connection status

Blinking: Connected Gray: Disconnected

Multi-control

Chapter 7 Controlling the projector

Viewer auto setting all together

"Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display from Viewer sub menu (selected by ‘Multi-control’ - “Network Viewer” menu). Set the display time periods and repeat times for the auto image display. After clicking Start button, the registered projectors start playing back the auto image display in sequential.

✐ For further information of the Auto display, see "Using the network

viewer function". (+p.124)

✐ This is effective only if the multi control item of the registered projector is

set to either "Control & Image" or "Image".

Chapter

Network Capture is a function to display the screen image and reproduce the sound of the computer via the network.

- Real Time Capture

- Network Communication

- Moderator Function

- Playing Movie files

8. Network capture functions

Chapter 8 Network capture functions

Start up the Network Capture 5

To start up the Network Capture 5, click "Network Capture 5" from "Start" - "All Programs" - "Network Viewer & Capture 5" menu. The application window will appear and search the projectors in the network and list them on the projector list. If any projector is not listed, check followings and then search again by pressing PJ Search button.

- Is the projector turning on and connected to the network?

- Is the network setting of projector and computer configuring correct?

- Is the same capture port no. used among computer and projectors?

About Network Capture function

The Network Capture is a function to display the screen image and reproduce the sound of the computer which has a Network Capture 5 software by the projector through the network. This function has 3 kinds of mode as below.

- Real Time Capture (+p.91)

A function to display the screen image and reproduce the sound of the computer by the projector through the network in real time.

- Network Communication (+p.96)

This mode is to communicate by sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool.

- Moderator Function (+p.107)

The moderator can project the participants’ computer screen through the projector in meetings or in classes.

✐ Up to 30 computers can be registered. ✐ The Network Capture function cannot be used when the Network Viewer function is used. The Real Time Capture,

Network Communication, Moderator function and Memory Viewer function cannot be used at the same time.

Commands on the task bar

When the Network Viewer & Capture 5 icon on the task bar is clicked, the popup menu will appear. It provides according to the operating modes as shown in the table below.

Items Description

Start real time / Terminate capture ...... Starts / Terminates the real time capturing. (+p.91) The screen image of the computer

is projected on the screen in real time.

One-shot capture ............................... Transfers the one-shot screen image of the computer.

Capture transfer ................................. Transfers the screen image of the computer to the projector.

The captured image edit

window appears on the computer screen.

Select capture object* .......................... Sets to display the capture window selection dialog.

* This menu will appear when "Select capturing object" is checked on the parameter

setting. (p.90)

Terminate communication .................. Terminates the network communication.

Start editing ...................................... Acquires the screen image in the network communication and displays it on the

editing window on the computer.

Terminate editing ..............................Terminates the editing window of the network communication.

Terminate Play movie files ..................Terminate the Play movie files.

Parameter set up ............................... Sets the communication parameter between the computer and projector. For further

information, see item "Parameter set up" on the next page.

Window show.................................... Displays the application window on the screen.

Version information ........................... Displays the version of this software.

Shut down......................................... Quits the Network Capture 5 application.

About Network Capture function

Parameter set up...

Window show.. Version information.. Shut down

Network Capture activating

One-shot capture Terminate capture

Window show.. Version information.. Shut down

Real time capture executing

Start real time capture One-shot capture Terminate capture

Window show.. Version information.. Shut down

One-shot executing

Menu during Real time capturing

Capture transfer Terminate Communication

Version information.. Shut down

Communication executing (Main PC)

Menu during Network Communication

Menu during Moderator function

Start editing Terminate Communication

Version information.. Shut down

Communication executing (Sub PC)

Capture transfer End editing

Version information.. Shut down

Leave moderator's group

Version information.. Shut down

Joining in Moderator's group (client PC)

Communication executing (Sub PC)

Real time capture executing

One-shot executing

One-shot capture Terminate capture

Window show.. Version information.. Shut down

Start real time capture One-shot capture Terminate capture

Window show.. Version information.. Shut down

Menu during Playing movie files

Terminate Play movie files

Window show.. Version information.. Shut down

Playing movie files

Chapter 8 Network capture functions

Parameter set up

Click Parameter set up button and setup the parameters on the Parameter setup window.

Items Description

Connection setting

Capture port ............... Sets the capture port no. on the projector. Default is 9000.

Pincode ......................... Sets the Network PIN code on the projector.

PJ search time ............. Sets the time to search the projector between 1 to 60 seconds. Default is 5 seconds.

q Search PJ when starting up Network capture

Check if Search PJ automatically starts when launching the network capture function.

q Select normal network adapter Uses default setting. Default is un-checked.

q Auto-power on ...... The projector turns on and projects the computer's captured image on the screen

automatically when the network capture is executed while the projector is in the standby.

Image setting

Display adapter .......... Provided for the use of a computer with

multiple network adaptors installed. Select a network adaptor which has the computer's screen to project with the projector and execute the network capture function. This is useful function when you make the presentation.

Select capturing object

.... Check if you want to select an

individual window on the computer screen. This is useful function when you open the multiple windows on the computer's screen. When you execute the capturing, the window selection dialog appears. Select a window name from the dialog window. The projected window size is automatically adjusted to fit the projector's screen size.

Sharpness..................... Select a capturing picture quality

among "High, "Medium", "Low"

q Reduce image ........ Check if the capturing image resolution

is more than projector's panel resolution (WXGA),

Layer window capture .

Check if layer window image capturing.

Capture start up time

...... Sets the delayed time from the capture

start in second. Moderator function setting

Nickname ..................... Sets moderator's nick name

Moderator login password

.. Sets Moderator's password

Play Movie files setting

Repeat times ...............

Sets repeat times of the playing movie files. If set to “0”, loop play the movie file lists endlessly.

✐ To check the Capture Port number, see item "Control by the web browser" (+ p.93). To check the PIN code, see item

"Network PIN code setting" (+ p.32, p.42).

✐ Specify the port number of TCP/IP. The default port setting is 9000. There are some reserved port numbers and also

some applications may use their own port numbers. If one of those port numbers is used, the alert dialog window will appear and let you know that it is an invalid port number. In that case, use another port number.

✐ The reserved port numbers are http (80), ftp (21), telnet (23), (25), (110), etc. The port no. 4352, 10000, 10001 are

reserved to control the projector through the LAN port.

Using the Real Time Capture

This is a function to project the screen image and reproduce the sound of the computer by the projector in real time. The captured image projected by the projector can be selected from the computer, web browser and the projector respectively.

Registering the computers

Up to 30 computers can be registered.

1 Access to the control page of the projector by using the web

browser. From the Network menu, click Capture tab to display the setting page.

2 Switch to Connection Setting page by clicking the page

number tab [3]. Enter the IP address of the computer to the PC number, and then click Set button. Click Set button to register the IP address for each page.

✐ When you capture the screen image of the movie player software with the real time capture function, the projector

may not be able to reproduce the sound. To reproduce the sound in the projector correctly, follow the procedures below;

• Start up the Network Capture 5 software first, start up the real time capture and then start up the movie player software.

• Terminate the movie player software first and then terminate the real time capture.

✐ The registered computer enables to start capturing if only the Network Capture 5 is activated. ✐ The transfer speed of the captured image using the Real Time Capture function is depending on the network

environment and data volume of the image. It cannot be supported for movie pictures.

✐ If you start capturing with the Select capturing object on the parameter set up window checked, the Select

capturing object window below (right side) appears. Select the desired window title from the window list and click OK button.

If no window is opened, no window title is displayed on the window list as shown on the left figure. Even the new window is opened, the display of the Select capturing object window would not change. If you would like to capture the new window opened, click Update button to show the window title on the window list, select it and click OK button.

Using the Real Time Capture

Chapter 8 Network capture functions

[1] Control by the computer

PC1

PC4 PC3 PC6

Capture

PC5

PC2

Project this screen image with PJ2.

* PC provides the Network Capture.

PJ2

PJ1

Select input mode to "Network" previously.

1 Start up Network Capture 5. 2 Select the projector(s) listed on the projector list on the application window and click Start real time

capture. The application window will disappear and then the screen image of the computer will appear on the projected screen in real time.

* You can select multiple projectors (up to 5) on the projector list.

• To stop capturing, click One-shot capture on the popup menu

appearing by clicking on the Network

Capture 5 icon on the task bar

. The captured image of the computer on the screen is frozen.

• To restart capturing, click Start real time capture on the popup menu.

3 To end capturing, click Terminate capture on the popup menu appeared by clicking on the Network

Capture 5 icon on the task bar.

* Start capturing from the

PC1.

✐ If the error message appears, check the item "Parameter set up" (+ p.90). ✐ The sound output from the projector can be controlled with the volume slider and mute item on the application

window of the Network Capture 5 software (+ p.25-26, p.90).

One-shot capture Terminate Capture

Window show.. Version information.. Shut down

Select "Network" as input mode previously.

1 Access to the control page of the projector by using the web

browser. From the Network menu, click Capture tab to display the setting page.

2 Select the computer number from the pull-down menu button

of "Connecting PC" and click Start button. The screen image of the selected computer will appear on the projected screen in real time.

• To stop capturing, click One-shot button. The captured image of the computer on the screen is frozen.

• To restart capturing, click Start button.

3 To end capturing, click End button.

✐ The IP address of the connecting PC should be registered previously (+ p.91). ✐ If the error message appears, check item "Parameter set up" (+ p.90). ✐ To use the capture function from the web browser or projector, the Network Capture 5 on the captured computer

must be activated.

PC4 PC3 PC6

Capture

PC5

PC2 PC1

* PC provides the Network Capture.

Project a screen image of PC1 with PJ2.

PJ2

PJ1

* Start capturing of

th e PC1 f ro m the PC5.

[2] Control by the web browser

Set "On" when using the wireless mouse function

Using the real time capture

Item Description

Interrupt connection ............... Set enable or disable the real time capturing

connection from other computers during executing the real time capturing operation.

Chapter 8 Network capture functions

PC4 PC3 PC6

Capture

PC5

PC2 PC1

PJ2

PJ1

* PC provides the Network Capture.

Project a screen image of PC1 with PJ2.

* Sta r t capt uri ng of

th e P C1 fr om th e projector PJ2.

[3] Control by the projector

Select "Network" in the Input menu previously.

1 Select "Network capture" in the Network menu. Press Point 8 or SELECT button. 2 Select "PC number" and press SELECT button and using Point ed buttons to select the PC number

to connect, and then press SELECT button.

3 Select "Connected" and then press SELECT button to start capturing. The screen image of the

selected computer will appear on the projected screen in real time.

4 To end capturing, select "Disconnect" and then press SELECT button.

✐ The IP address of the connecting PC should be registered previously (+ p.91). ✐ If the error message appears, check item "Parameter set up" (+ p.90). ✐ The projector does not provide the function to register the IP address of the computer and to set the parameter of

the capturing. They should be registered by using the web browser previously (+ p.91).

✐ The remote control which is provided with the projector does not have the mouse operating function.

Set "On" when using the wireless mouse function

PC1

＊USB memory provides Auto Capture program.

PC2

Project this screen image with PJ1.

PJ1

The real time capture function can run automatically on the computer without the Network Viewer & Capture 5 software installed by executing the Auto Capture program in the USB thumb drive connected to the computer. The USB thumb drive for Auto Capture is supplied with this projector.

1. Turn on the projector and select “Network” from the input menu of the projector.

2. Select “LAN mode select” from the "Network" menu of the projector and press SELECT button. Select

"Wired 1/2/3" or “Wireless Simple” with the Point ed buttons. (+ p.41)

3. By connecting the above USB thumb drive, the removable disk window appears. Select "[Network Capture 5] Open Program using the program provided on the device." and then click OK.

4. Automatically, the activated executable file configures the Easy wireless setting. (If the network adaptor selecting window appears, select an option according to your network environment.) Then, it searches the projector, and starts the real time capture of the computer screen.

5. If the auto-run program does not start automatically, double-click "WinAutoCap5" in the USB thumb drive. (The auto-run program works only with Windows XP and Windows Vista.)

*The connection process of AutoCapture is different according to the equipped LAN adapter.. In case of only the wired LAN adapter is provided in the computer: Connect to the network with the wired LAN adapter and search a projector. In case of only the wireless LAN adapter is provided in the computer:

Change the LAN setting of the computer to SIMPLE and search a projector with the wireless LAN adapter.

In case of both the wired and wireless LAN adapters are provided in the computer:

When "Usually set it to a network adapter to use" is not checked; the network selection window is displayed.

6. For the following operations, refer to Page 92.

Using the real time capture

[4] Control by the computer with USB memory

✐ If the error message appears, check item "Parameter set up" (+ p.90). ✐ When your computer provides multiple network adaptors, and "Select normal network adaptor" on the parameter

setup window is un-checked, the network adaptor selecting window (+ p.26) will appear.

✐ When plural projectors are found, the real-time capture will not start, but will become standby status. Release the

wireless LAN SIMPLE setting of the projector which is not for the real-time capture.

✐ When the software of Network Capture 5 is not installed in the computer, the sound data is not transferred. If you

want to transfer the sound data, install the software beforehand.

✐ If the specified files are copied in the root of commercial USB memory, you can also perform the AutoCapture.

* Start capturing of

the PC1.

Setting condition for automatically starting the real time capture function

Projector: Power: On, Input mode: Network, LAN mode select: Wired 1/2/3 or Wireless Simple The searching result becomes only one projector. Computer PC1: Log in by Administrative The wireless LAN card or the wired LAN card: Provided, Network Capture 5 software: NIL Activate WinAutoCap5 in USB thumb drive

Chapter 8 Network capture functions

Using the Network Communication

This Network Communication is to communicate by sharing the captured image of a computer with multiple computers and a projector. Users can draw the text and figure on the captured image by using a drawing tool. The data that has the captured image of a Main PC and communication information is sent to the projector. The projector projects this data onto the screen and serves this data to other computers (Sub PC) at the same time. The Sub PC receives served captured data and displays it on the screen. The Main PC and Sub PC also can edit the captured image by using the drawing tool. This edited image is applied to all the computers automatically.

Example of advanced use

Displays the presentation data stored in the computer by using the wireless mouse function from the projector.

1 Start capturing of the computer PC1 by using the projector.

Select “Network Capture” icon from the menu and select "PC1" and then select "Connect" (+ p.94). => The Network Capture software installed in the selected computer will start capturing.

2 On the image of the PC1 projected on the screen, search a presentation file data stored in the PC1 by

using the wireless mouse function of the remote control supplied with the projector.

3 Select a desired file and double click with the remote control .

=> The application by which the document was created starts and the projector projects the presentation picture

on the screen.

4 Start the presentation.

=> By using wireless mouse function, control the page browsing and some other operations for the PC1.

✐ For further instructions of the wireless mouse, please refer to the projector’s owners manual. ✐ On the projected screen using with the network capture, the shape of the mouse pointer differs from the one on

the computer’s screen.

PC4 PC3

Capture

PC5

PC2

PJ2

PC1

* PC provides the Network Capture.

* Controls PC1 with wireless mouse.

Project a screen image of PC1 with PJ2.

Setting condition

Projector

Input mode: Network Registering the connection:

The IP address of the computer and proper parameter must be set to the PC1 (+ p.90-91). Mouse Display: "On" (+ p.93)

Computer PC1

Software:

The Network Capture 5 is activated.

PC2

PC6

Capture

PC5

PC1

Capture a screen image of PC5 and make marking with a tool.

PJ1

* The Main PC is a computer which started using communication function, and serves own

computer screen captured image to the Sub PC. The Main PC has an authority to quit using whole communication. To become the Main PC, execute the command "Start Communication" or "Capture transfer". For further information, see item "How to use the Network Communication". (+p.100)

* The Sub PC is a computer which receives a captured image from the Main PC. On the communication

mode, the Sub PC can become the Main PC.

Settings before using the Network Communication

To use the Network Communication, the capture setting of the projector must be set either [1] or [2] as described below.

[1] Projector searches all the available subject computers in

the network automatically.

[2] Subject computers are registered to the projector.

Perform capture setting following to the description below.

[1] When serving the capture data to all the sub-

ject computers in the network.

By using the web browser, display "Communication Setting" from menu "Network"-"Capture"-"Page 2". Confirm that the item Auto search subject PC is "ON". If "OFF", change mode to "ON".

* Projector can find up to 30 computers in the network.

[2] When serving the capture data to the specific

subject computers in the network.

Set the item Auto search subject PC "OFF" described in the above and then display "Connection Setting" from menu "Network"-"Capture"-"Page 3" with the web browser. Enter the IP address of subject computer and click Set button to register.

* Up to 30 computers can be registered to the projector.

✐

To display the served capture data, the software Network Capture 5 must be installed on the computer.

Using the Network Communication

Chapter 8 Network capture functions

Description of capture editing window

Start Network Capture 5 and select the projector(s) on the projector list on the application window and click Communication Start button. The application window will disappear and the capture editing window will appear on the computer screen as below. For basic operation of each menu, refer to the item "Menu tree" below.

Capture Image

Authority st atus ind icati on frame

(+p.100)

Tool bar

Menu tree

Menu Submenu Operation

File Save Communication Saves a captured editing image as the data(JPEG)

Saves dialog window appears

Terminate Communication

* main pc only

Quits the communication mode

End Editing

* sub pc only

Closes the Editing window

Control Capture transfer

Captures a screen image and sends it to the projector

Authority

Acquires/releases the authority to edit the capture image Edit Tool Pencil Selects a pencil tool Eraser Selects an eraser tool Letter frame Selects a letter frame tool Form Free Draws line with freehand (Shape) Straight line Draws straight line Square Draws square Oval Draws oval

Square(Painting out)

Draws filled square Oval(Painting out) Draws filled oval Attribute Appears a attribute window Delete all Deletes all the drawings on the image Undo Cancels the last executed operation Display Full screen

Switches capture editing window, normal or full screen Tool bar Standard Switches standard tool buttons on or off Form(shape) Switches form(Shape) tool buttons on or off Color Switches color tool buttons on r off Attribute Switches attribute tool buttons on or off Display on foreground Keeps capture editing window on foreground always Help Version information Displays software version number

Tool bar button names

The following commands are assigned to the tool bar buttons. For each operation, refer to the description of the item "Menu tree".

✐ To switch the tool bars displaying on or off, select each command from menu "Display"-"Tool bar". ✐ User can realign and join the tool bars (Standard, Shape, Color, Attribute), and change it to the floating pallet by a

drag and drop of the tool bars.

✐

There are some disable buttons depending on the tools and authority mode. In that case the button appears in gray.

Capture

transfer

Authority

Terminate Communication

Save

communication

Attribute

Oval(Painting out)

Straight lineLetter

frame

Square(Painting out)

Square

Eraser

Pencil

Free Oval

Form tool bar

Standard tool bar

Width (Large, Medium, Small)

Color pallet 16 colors

Translucence

Color tool bar

Attribute tool bar

End Editing

Command Tool Bar of Sub PC

Command Tool Bar of Main PC

Using the Network Communication

100

Chapter 8 Network capture functions

How to acquire and release the editing authority

To edit the capture image, each computer needs to acquire the authority respectively. To acquire the authority, click " : Authority" button on the standard tool bar and then edit the capture image. The capture editing window indicates the authority status by changing the frame color depending on the current authority mode as follows.

having an authority

other computer having an

authority

ready to acquire an authority

Red Blue Green

Exit from the communication (only for Sub PC)

Click " :End editing" button on the standard tool bar. The capture editing window will be closed.

✐ This command is available with the Sub PC only. ✐

When "End editing" with the authority provided is executed, the authority will be released.

End the communication

Click " :Terminate Communication" button on the standard tool bar. The capture editing window will be closed.

✐ This command is available with the Main PC only. ✐

The communication cannot be ended while other PC has the authority. To end communication forcibly, click the Capture 5 icon on the task bar and select "Shut down" on the popup menu.

How to use the Network communication

Start the communication

1 Display an image on the computer screen. 2 Start Network Capture 5. The application window appears and the projectors in the network are listed. 3 Select the projector(s) and click Start Communication button. The application window disappears and

the capture editing window with a captured image appears on the computer screen. The projector displays captured image on the screen.

✐ If an error message appears, check the item "Parameter set up". (+p.90)

Join the communication (only for Sub PC)

1 Start Network Capture 5. The application window appears and lists the projector in the network. 2 Select a projector whose status on the projector list indicates "Communication starting", and click

Start communication button. The application window disappears.

3 Click Start editing menu on the popup menu appeared by clicking the Network Capture 5 icon on

the task bar.

The capture editing window with a captured image appears on the computer screen.

Eiki Digital projector, 1AV4U19B25500 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual