Ei Electronics Ei 3100RF User Manual
1
SMOKE ALARM
Radio Wireless
Interconnect
Instruction Leaflet
Contains vital information on unit operation and installation.
Read and retain carefully. If you are just installing the unit,
this leaflet MUST be given to the householder.
Model:
Ei 3105RF (OPTICAL WITH HUSH)
Ei 3100RF (IONISATION)
P/N B15??? Rev 0
Table of Contents
1 READ THIS FIRST
2 INTRODUCTION
3 LOCATING YOUR SMOKE ALARMS
4 POSITIONING YOUR SMOKE ALARM
5 INSTALLING YOUR SMOKE ALARMS
6 HOUSE CODING YOUR ALARMS
7 TESTING AND MAINTAINING YOUR
SMOKE ALARMS
8 TROUBLESHOOTING YOUR ALARMS
9 IMPORTANT SAFEGUARDS
10 SMOKE ALARM & RF LIMITATIONS
11 GETTING YOUR SMOKE ALARM SERVICED
12 FIVE YEAR GUARANTEE
13 SMOKE ALARM - OPTICAL OR IONISATION
14 TECHNICAL SPECIFICATION
1. READ THIS FIRST
A Smoke Alarm is an early warning device. Used correctly it
can give you and your family valuable extra time to escape.
When the alarm sounds, immediately evacuate the premises
before beginning any investigation.
1. Install in the centre of the ceiling (if possible) using the
screws supplied (see section 5.0)
2. Connect battery: Connect battery snaps firmly (see figure
1a). Press the test button and horn should sound.
3. When the battery is first connected the Alarm may sound
for 2-3 seconds and/or the red light may flash quickly for 10
seconds - this is normal.
4. The wireless interconnect will operate as received once the
batteries are connected. We strongly recommend house
coding your alarms to prevent interference from
neighbouring systems (see section 6)
5. Test weekly.
6. Proper protection usually requires more than one Smoke
Alarm.
7. If the Alarm beeps without the red light flashing at the same
time then clean the unit, as this is the automatic test feature
indicating the chamber is degraded (Ei3105RF only).
8. ASmoke Alarm does not prevent fires.
9. Plan your escape route.
2
Figure 1 : Attaching battery to the battery snap
2
3
3
5
7
9
10
13
14
16
17
17
18
19
Page
3
10. If you have any doubt or query about Smoke Alarms consult the supplier or your local Fire Brigade.
2. INTRODUCTION
Congratulations on purchasing Ei3105RF or Ei3100RF
RadioLINK Smoke Alarms. You can easily install these
alarms throughout the house in closed rooms, corridors and
in the attic for the fastest response to developing fires.
Closed doors are great for slowing down the spread of fire,
but unfortunately they can also greatly slow down the
response time of alarms, as they block the smoke getting to
them. Without interconnection, closed doors also greatly
reduce the alarm sound level throughout the house, so even
though the fire is detected early, the alarm may not be heard.
The Ei3105RF/Ei3100RF RadioLINK Smoke Alarms offer the
comfort of interconnection without the hassle of installing the
interconnect wires. The wireless interconnect helps ensure
the alarm will be heard everywhere - including the bedrooms.
The wireless interconnect will operate as received once the
batteries are connected. To check operation, first connect all
the batteries (see section 1 para 2.) and then hold down the
test button on the first unit until the amber light comes on continuously for 3.5 seconds. All the other smoke alarms will
respond within 5 seconds. If there is any possibility of a
neighbour having a similar system, you should house code
your units so your system will not cause his/hers to alarm or
vice versa. This is easily done and only takes a few minutes(see section 6.0).
3. LOCATING YOUR SMOKE ALARMS
Sufficient smoke must enter your Smoke Alarm before it will
respond. Your Smoke Alarm needs to be within 10 paces (7.5
metres) of the fire to respond quickly . The smoke alarms need
to be in positions where they can be heard throughout your
home, so they can wake you and your family in time for everyone to escape. A single Smoke Alarm will give some protection if it is properly installed, but most homes will require two
or more to ensure that a reliable early warning is given. For
recommended protection you should put individual Smoke
Alarms in all the rooms (apart from the kitchen) where fire is
most likely to break out.
Your first Smoke Alarm should be located between the sleeping area and the most likely sources of fire (living room or
kitchen for example). But it should not be more than 10 paces
(7.5 metres) from the door to any room where a fire might
start and block your escape from the house.
3.1 Single Storey Dwelling.
If your Home is on one level (a bungalow or mobile home for
4
example) you should put your first Smoke Alarm in a corridor
or hallway between the sleeping and living areas. Place it as
near to the living area as possible, but make sure you can
hear it loudly enough to wake you in the bedroom. (for example, see figure 2).
If your bungalow is very large and the corridor or hallway is
more than say 20 paces (15 metres) long, one Smoke Alarm
will not be sufficient. This is because no matter where it is
located it will be more than 7.5 metres from potential fires.
Recommended locations, Figures 2, 3, & 4
for minimum protection
• on each storey
• in each sleeping area
• every 7.5 metres of hallways & rooms
• within 3 metres of all bedroom doors
• all units interconnected
for recommended protection
in addition
• in every room (except bathrooms and kitchens)
Figure 2: Single storey dwelling
Figure 3: Single storey dwelling with separate sleeping areas
In houses with more than one sleeping area, Smoke Alarms
should be placed between each sleeping area and the living
area (for example, see figure 3).
BEDROOM
DINING ROOM
KITCHEN
BEDROOM
BATH
ROOM
BEDROOM
LIVING ROOM
BEDROOM
DINING ROOM
KITCHEN
BEDROOM
BEDROOM
3.2 Multi Storey Dwellings
If your home has more than one floor, at least one alarm should
be fitted on each level (see figure 4). The Ei3105RF/Ei3100RF
Wireless Smoke Alarm is ideal in this situation as they are
automatically interconnected without wiring.
3.3 Recommended Protection
Fire authorities recommend you put individual Smoke Alarms
in or near all the rooms where fire is most likely to break out
(apart from the locations to avoid, mentioned below). The living room is the most likely place for a fire to start at night, followed by the kitchen and then the dining room. You should
also consider putting Smoke Alarms in any bedrooms where
fires might occur, for instance, where there is an electrical
appliance such as an electric blanket or heater, or where the
occupant is a smoker. You could also consider putting Smoke
Alarms in any rooms where the occupant is unable to respond
very well to a fire starting in the room, such as an elderly or
sick person or a very young child.
Figure 4: Multi Storey Dwelling
3.4 Checking you can hear your Smoke Alarms
With the Smoke Alarms sounding in their intended locations,
check you are able to hear them in each bedroom with the
door closed, above the sound of your Audio/TV Systems. The
Audio/TV systems should be set to a reasonably loud conversation level. If you can’t hear it over your radio the chances
are that it wouldn’t wake you. This Wireless Smoke Alarm will
help to ensure the alarm will be heard through-out the house.
4. POSITIONING YOUR SMOKE ALARM
4.1 On a ceiling
Hot smoke rises and spreads out, so a central ceiling position
is the recommended location. The air is “dead” and does not
move in corners, therefore Smoke Alarms must be mounted
away from corners. Place the unit at least 0.30m from any
light fitting or decorative object which might obstruct smoke
5
6
entering the Smoke Alarm. Keep at least 0.30m away from
walls and corners (see figure 5).
4.2 Wall Mounting
When a ceiling position is not possible (for example on a ceiling having exposed beams or joists, or built-in radiant heating) put the top edge of your Smoke Alarm between 0.15m
and 0.30m below the ceiling. Keep at least 0.30m from corners (see figure 5).
4.3 On a sloping Ceiling
In areas with sloping or peaked ceilings install your Smoke
Alarm 0.90m from the highest point measured horizontally
(see figure 6), because “dead air” at the apex may prevent
smoke from reaching the unit.
4.4 Locations to Avoid
Don’t place your Smoke Alarm in any of the following areas:
• Bathrooms, kitchen, shower rooms, garages or other rooms
where the smoke alarm may be triggered by steam,
condensation, normal smoke or fumes.
• Attics or other places where extremes of temperature may
occur (below 4°C or above 40°C).
• Near a decorative object, door, light fitting, window molding
etc., that may prevent smoke from entering the Smoke
Alarm.
• Surfaces that are normally warmer or colder than the rest of
the room (for example attic hatches, uninsulated exterior
walls etc). Temperature differences might stop smoke from
reaching the unit.
• Next to or directly above heaters or air conditioning vents,
windows, wall vents etc. that can change the direction of
airflow.
• In very high or awkward areas where it may be difficult to
reach the alarm for testing or battery replacement.
• Locate unit at least 1.5m away from fluorescent light fittings
as electrical “noise” and/or flickering may affect the unit.
• Locate away from very dusty or dirty areas as dust build-up
in the chamber can make unit too sensitive and prone to
alarm.
Figure 5 Figure 6
IDEAL IN CENTRE
OF CEILING
0.9m
(3 FEET)
DEAD AIR SPACES
NEVER WITHIN 0.3m
OF ANY CORNER
0.15 to 0.3m
7
It can also block the insect screen mesh and prevent smoke
from entering the chamber.
• Do not locate in insect infested areas. Small insects getting
in to the chamber can cause intermittent alarms.
5. INSTALLING YOUR SMOKE ALARMS
(a) Attaching to Ceiling or Wall.
Figure 7
Figure 7a
Ei3105RF
Ei3100RF
AMBER
LIGHT
PUSH BACK
TO EASE
BATTERY
REMOVAL
OPEN TAB
BATTERY
INSTALLATION
DATE
TEST & HUSH
BUTTON
COVER
AMBER
LIGHT
PUSH BACK
TO EASE
BATTERY
REMOVAL
BATTERY
BATTERY
SCREW HOLE
OPEN TAB
BATTERY
INSTALLATION
DATE
SNAP ON
HINGES
SCREW HOLE
HOUSE CODE SWITCH
8
1. Pull cover open at tab. Remove cover from base by separating at rear snap-in hinges by rotating cover backwards.
2. Place the base on ceiling or wall exactly where you want to
mount the unit. With a pencil, mark the location of the screw
holes.
3. Taking care to avoid any electrical wiring in the ceiling or
wall, drill a hole through the centres of the marked locations.
Push the plastic Screw Anchors provided into the drilled
holes. Screw in firmly.
(b) Connecting the battery
The battery is easily removed from the holder by holding back
one of the plastic clips while lifting the battery with the other
hand.
Snap Battery Connectors to Battery . They fit together only one
way.
Gently push Battery into Battery Holder
With a pencil, write the date of battery installation on the
inside of the cover to remind you when to replace the battery.
To close the cover match up snap-in hinges and gently press
together until base and cover snap together. Test the installed
Smoke Alarm - see section “Manually Testing your Smoke
Alarm”.
NOTE: You may hear a loud chirp when attaching the Battery
Connectors to the Battery.
Battery Missing indicator
The unit is fitted with a warning flag which pops up when the
battery is removed. This prevents the cover from closing when
there is no battery in the unit. When the battery is being
installed or changed, this flag must be held down while gently
pushing the Battery into the Battery Holder. (Figure 8).
7.Check the radio link interconnection by holding the test button down until the amber light has come on continuously – this
indicates that the alarm is now transmitting radio link signals.
You should now be able to hear the other alarm(s) in the distance. If you do not hear the other alarm(s) then you may
need to rotate/resite the alarm (see section 5.2 below).
Figure 8
Loading...