EICO 324 Service Manual
MODEL 324 ADDENDUM
.
--------------------
,
Please make the ,following changes in your Instruction Man al
replacement parts list and schematic diagram parts list:
,Remove 93003CRl Rect., 50 ma ,
Add 93022 CRl Rect.
Change the stock # of the following paper capacitors to mylar
Change stock #30013 (Tl transformer, power)to 30022.
Remove 93003 CRl Recto, 50ma.
,Add 93022 CRL Rect. PWR, siliaon, 600V, 750ma.
P-'--+......,..,........-~~-.••
t!h.=change
Change 54003 TB2 termo post, 2 post (Am't 1) to
54003 TB2, 4 term~ post,I2 post (Am't 2).
Change the stock
#
of the following paper capacitors to myl,ar
capacitors~
20000 to 20087~ 20001 to 20042~ 20006 to 20089: 2000B to 20086.
Change stock.#300l3 (Tl transformer, pwwer) to 30022)
,Pl'-lR. ,
Silicon, '600V, 750ma.
If you have a kit, please make the following changes in your
construction manual 'replacement parts list and schematic
diagram parts 'list:
capacitors: 20000 to 20087~ 20001 to 20042~ 20006 to 20089:
20008 to 20086.'
4TOD~crew;
'""6
-3
l'
X""""""i!4
(amt:
6~ to
(amt
,1)
Since we have replaced the 93003 selenium rectifier w~th a
93022 silicon rectifier, the following 'changes ,must be made
in the Construction steps.
(Before proceeding, please number the steps in the manual to
simplify the identification of each step) .
That is, Fig. 1, Steps 1 and 2. Fig. 2, Steps 1 through 11
Fig. 3 Stepsl and 2 etc.)
Figure 2 step 2 - Change entire step as follows:
r:
2. ( ) Fig. 2. Mount the 2 post terminal, strip TB4 through the
hole in which the old selenium rectifier is shown i~,Fig. 2)
Use 1 #6-32 X 1/4 screw, 1 #~,lockwasher and 1 #6 x nut.
Correct Figure 2 by replacing the rectifier with a 2 post
terminal strip. Number the posts of the terminal strip 1 and
2
("1"
coincides with the,
"+"
terminal of the selenium rectifier)
Figure 6, Step 11 - Change entire step as follows::
11. ( ) Fig. 60 Connect the other red lead of the power trans-
former Tl to TB4-2 (C)
0 ' ~
Figure 6, step 14 - change entire step as followS;"
14. ( ) Fig. 6. connect one red Lead of the dual 20MFD
capacitor C3 to TB4-l (C).
·1ODEL 324
DENDUM
----------------------
Add step 14A:- cut both leads on t"e s
to
"1".
connect the cathode end (tapered end, end with marking band,
or end to which the arrow points) to TB4-1 (C). connect the
other lead to TB4-2
(s)"
i.l.Lcon
rectifier CRl
.
Figure
15. ( ) Fig.
(S) to
lated double lug.
For reference purposes, the end of the double lug nearest TB4
is designated TB1-l,B1and the opposite end is TB1-lA.. The
metal foot by which TBI is mounted is designated as TBl-2.
IE.
1992
6,
step .15 - cnange entire step as follows~
6/
Connect ~he 2.2K ohm resistor
TBI-IB.
(C).
Note that terminal strip TBl has one insu-
EICO ELECTRONICS INSTRUMENT CO. INC.
283 Malta Sto Bklyn/ N. Y. 11207
R~
from TB4-l
Loading...