EIC SS1M, SS1K, SS1J, SS1G, SS1E Datasheet
...
SS1A - SS1M
SUPER FAST RECTIFIERS
PRV : 50 - 1000 Volts
Io : 1.0 Ampere
FEATURES :
* High current capability
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
UPDATE : JULY 24, 1998
2.1 ± 0.2
1.2 ± 0.2
5.0
±
0.15
4.5
±
0.15
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Super fast recovery time
SURFACE MOUNT
SMA (DO-214AC)
1.1 ± 0.3
0.2 ± 0.07
2.6 ± 0.15
* Case : SMA Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Lead Formed for Surface Mount
2.0 ± 0.2
Dimensions in millimeter
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.064 gram
RATING
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 800 1000 Volts
Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 560 700 Volts
Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 800 1000 Volts
Maximum Average Forward Current Ta = 55 °C
Peak Forward Surge Current
8.3 ms. Single half sine wave Superimposed
on rated load (JEDEC Method) IFSM 30 Amps.
Maximum Peak Forward Voltage at IF = 1.0 Amp. VF 0.95 1.4 1.7 Volts
Maximum DC Reverse Current Ta = 25 °C
at Rated DC Blocking Voltage Ta = 100 °C
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 ) CJ 50 pf
Junction Temperature Range TJ - 65 to + 150
Storage Temperature Range TSTG - 65 to + 150
SYMBOL SS1A SS1B SS1C SS1D SS1E SS1G SS1J SS1K SS1M UNIT
IF(AV) 1.0 Amp.
IR 5
IR(H) 50
Trr
35 ns
µA
µA
°C
°C
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC
RATING AND CHARACTERISTIC CURVES ( SS1A - SS1M )
+
125
175
0300
80
100
0204060120
0
- 0.25
- 1.0 A
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
Ω
50 Vdc
(approx)
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
1.0
0.8
0.6
0.4
CURRENT, AMPERES
0.2
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100
AMBIENT TEMPERATURE, ( °C)
D.U.T.
1
Ω
10
Ω
OSCILLOSCOPE
150
( NOTE 1 )
+ 0.5 A
PULSE
GENERATOR
( NOTE 2 )
24
18
12
CURRENT, AMPERES
6.0
PEAK FORWARD SURGE
1 2 4 6 10 20 40 60 100
Trr
SET TIME BASE FOR 15 ns/cm
1 cm
8.3 ms SINGLE HALF SINE WAVE
Ta = 50 °C
NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
100 10
Pulse Width = 300µs
2% Duty Cycle
TJ = 25 °C
10
SS1A - SS1D
1.0
SS1J - SS1M
0.1
FORWARD CURRENT, AMPERES
SS1E - SS1G
1.0
0.1
CURRENT, MICROAMPERES
INSTANTANEOUS REVERSE
0.01
PERCENT OF RATED REVERSE
TJ = 100 °C
TJ = 25 °C
140
VOLTAGE, (%)
0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
FORWARD VOLTAGE, VOLTS
Loading...