EIC SRR4, SRR2, SRR1, SRR0, SRR6 Datasheet
SRR0 - SRR6
FAST RECOVERY RECTIFIERS
PRV : 50 - 600 Volts
Io : 3.0 Amperes
FEATURES :
* High current capability
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
* Case : SMC Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Lead Formed for Surface Mount
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.21 gram
SURFACE MOUNT
SMC (DO-214AB)
0.060(1.52)
0.030(0.76)
0.305(7.75)
0.320(8.13)
0.280(7.11)
0.260(6.60)
0.121(3.07)
0.115(2.92)
0.245(6.22)
0.220(5.59)
Dimensions in inches and (millimeter)
0.103(2.62)
0.079(2.00)
0.008(0.203)
0.004(0.102)
0.012(0.305)
0.006(0.152)
RATING
Maximum Recurrent Peak Reverse Voltage V
Maximum RMS Voltage V
Maximum DC Blocking Voltage V
Maximum Average Forward Current Ta = 90 °C
SYMBOL SRR0 SRR1 SRR2 SRR4 SRR6 UNIT
RRM
RMS
F(AV)
I
DC
50 100 200 400 600 V
35 70 140 280 420 V
50 100 200 400 600 V
3.0 A
Maximum Peak Forward Surge Current,
8.3ms Single half sine wave superimposed
I
100 A
FSM
on rated load (JEDEC Method)
DC
R(H)
I
Trr
STG
F
R
I
1.25 V
10
150
µA
µA
150 ns
J
J
28 pf
- 65 to + 150
- 65 to + 150
°C
°C
Maximum Peak Forward Voltage at IF = 3.0 A V
Maximum DC Reverse Current Ta = 25 °C
at Rated DC Blocking Voltage Ta = 100 °C
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 ) C
Junction Temperature Range T
Storage Temperature Range T
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V
Page 1 of 2 Rev. 01 : April 2, 2002
RATING AND CHARACTERISTIC CURVES ( SRR0 - SRR6 )
+
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω 10 Ω
D.U.T.
50 Vdc
(approx)
1 Ω
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
OSCILLOSCOPE
( NOTE 1 )
PULSE
GENERATOR
( NOTE 2 )
+ 0.5 A
0
- 0.25 A
- 1.0 A
1 cm
Trr
SET TIME BASE FOR 50 ns/cm
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
3.0
2.4
1.8
1.2
0.6
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
AMBIENT TEMPERATURE, ( °C)
100
80
60
40
CURRENT, AMPERES
20
PEAK FORWARD SURGE
8.3 ms SINGLE HALF SINE WAVE
NUMBER OF CYCLES AT 60Hz
Ta = 50 °C
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
100
Pulse Width = 300 µs
2% Duty Cycle
10
1.0
0.1
TJ = 25 °C
FORWARD CURRENT, AMPERES
0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
10
TJ = 100 °C
1.0
0.1
TJ = 25 °C
0.01
80
100 1400 20 40 60 120
REVERSE CURRENT, MICROAMPERES
PERCENT OF RATED REVERSE
VOLTAGE, (%)
FORWARD VOLTAGE, VOLTS
Page 2 of 2 Rev. 01 : April 2, 2002
Loading...