EIC SRN7, SRN6, SRN5, SRN4, SRN3 Datasheet

SRN3 - SRN7

PRV : 50 - 600 Volts

Io : 1.0 Ampere

FEATURES :

* High current capability

MECHANICAL DATA :

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

Rating at 25

C ambient temperature unless otherwise specified.

Single phase, half wave, 60 Hz, resistive or inductive load.

For capacitive load, derate current by 20%.

2.1 ± 0.2

1.2 ± 0.2

5.0 ± 0.15

4.5

0.15

* High surge current capability * High reliability * Low reverse current * Low forward voltage drop * Fast switching for high efficiency

SURFACE MOUNT

FAST RECOVERY RECTIFIERS

SMA (DO-214AC)

1.1 ± 0.3

0.2 ± 0.07

2.6 ± 0.15

2.0 ± 0.2

* Case : SMA Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Lead Formed for Surface Mount * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.067 gram

RATING

Maximum Recurrent Peak Reverse Voltage V Maximum RMS Voltage V Maximum DC Blocking Voltage V Maximum Average Forward Current Ta = 50 °C

Maximum Peak Forward Surge Current,

8.3ms Single half sine wave Superimposed on rated load (JEDEC Method)

Maximum Peak Forward Voltage at IF = 1.0 A V Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) C Junction Temperature Range T Storage Temperature Range T

SYMBOL SRN3 SRN4 SRN5 SRN6 SRN7 UNIT

F(AV)

RRM RMS

FSM

R(H)

Trr

J J

STG

Dimensions in millimeter

50 100 200 400 600 V 35 70 140 280 420 V 50 100 200 400 600 V

1.0 A

30 A

1.2 V 5

150 ns

50 pf

- 65 to + 150

µA µA

°C °C

Notes :

( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V

Page 1 of 2 Rev. 01 : April 2, 2002

RATING AND CHARACTERISTIC CURVES ( SRN3 - SRN7 )

60Hz RESISTIVE OR INDUCTIVE

1.0

0.01

140

+ 0.5 0- 0.25

- 1.0 A

FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM

50 Ω 10 Ω

D.U.T.

50 Vdc

(approx.)

1 Ω

NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.

2. Rise time = 10 ns max., Source Impedance = 50 ohms.

3. All Resistors = Non-inductive Types.

OSCILLOSCOPE

( NOTE 1 )

PULSE

GENERATOR

( NOTE 2 )

Trr

SET TIME BASE FOR 50-100 ns/cm

FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK RECTIFIED CURRENT FORWARD SURGE CURRENT

0.4

CURRENT, AMPERES

8.3 ms SINGLE HALF SINE WAVE

CURRENT, AMPERES

PEAK FORWARD SURGE

Ta = 50 °C

AVERAGE FORWARD OUTPUT

0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100

AMBIENT TEMPERATURE, ( °C)

NUMBER OF CYCLES AT 60Hz

FORWARD CURRENT, AMPERES

Page 2 of 2 Rev. 01 : April 2, 2002

FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS

100

Pulse Width = 300 µs

1.0

2% Duty Cycle

TJ = 25 °C

REVERSE CURRENT, MICROAMPERES

TJ = 100 °C

TJ = 25 °C

PERCENT OF RATED REVERSE

VOLTAGE, (%)

0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0

FORWARD VOLTAGE, VOLTS