EIC SF13, SF12, SF11, SF14, SF16 Datasheet
...
SF11 - SF19
SUPER FAST RECTIFIER DIODES
PRV : 50 - 1000 Volts
Io : 1.0 Ampere
FEATURES :
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
UPDATE : MARCH 8, 2002
DO - 41
Dimensions in inches and ( millimeters )
* High current capability
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Super fast recovery time
* Case : DO-41 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.34 gram
RATING
Maximum Recurrent Peak Reverse Voltage V
Maximum RMS Voltage V
Maximum DC Blocking Voltage V
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55 °C
Peak Forward Surge Current,
8.3ms Single half sine wave superimposed
on rated load (JEDEC Method)
Maximum Peak Forward Voltage at IF = 1.0 A. V
Maximum DC Reverse Current
at Rated DC Blocking Voltage
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 ) C
Junction Temperature Range T
Storage Temperature Range T
SYMBOL SF11 SF12 SF13 SF14 SF15 SF16 SF17 SF18 SF19 UNIT
F(AV)
I
I
RRM
RMS
DC
FSM
R
I
Trr
STG
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
50 100 150 200 300 400 600 800 1000 Volts
35 70 105 140 210 280 420 560 700 Volts
50 100 150 200 300 400 600 800 1000 Volts
1.0
30
F
J
J
0.95 2.21.7
35 ns
50 pf
- 65 to + 150
- 65 to + 150
1.00 (25.4)
MIN.
0.205 (5.2)
0.166 (4.2)
1.00 (25.4)
MIN.
Amp.
Amps.
Volts
105.0
µA
°C
°C
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V
DC
RATING AND CHARACTERISTIC CURVES ( SF11 - SF19 )
+
1.0
10
24
20
8.3 ms SINGLE HALF SINE WAVE
+ 0.5 A
0
- 0.25 A
- 1.0 A
1 cm
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω 10 Ω
D.U.T.
50 Vdc
(approx)
1 Ω
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
OSCILLOSCOPE
( NOTE 1 )
PULSE
GENERATOR
( NOTE 2 )
Trr
SET TIME BASE FOR 15 ns/cm
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
30
Ta = 50 °C
0.6
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
AMBIENT TEMPERATURE, ( °C)
CURRENT, AMPERES
PEAK FORWARD SURGE
NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
100
TJ = 100 °C
TJ = 25 °C
1.0
SF11- SF14
SF15 - SF17
SF18 - SF19
0.1
MICROAMPERES
REVERSE CURRENT,
0.1
FORWARD CURRENT, AMPERES
0.01
0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0
Pulse Width = 300 µs
2% Duty Cycle
TJ = 25 °C
0.01
PERCENT OF RATED REVERSE
VOLTAGE, (%)
FORWARD VOLTAGE, VOLTS
Loading...