EIC RG10Y, RG10, RG10A Datasheet
RG10 - RG10Y
SUPER FAST RECTIFIER DIODES
PRV : 70 - 600 Volts
Io : 1.0 - 1.5 Amperes
FEATURES :
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
UPDATE : APRIL 23, 1998
D2
* High current capability
* High surge current capability
0.161 (4.1)
0.154 (3.9)
1.00 (25.4)
MIN.
* High reliability
* Low reverse current
* Low forward voltage drop
0.284 (7.2)
0.268 (6.8)
* Super fast recovery time
1.00 (25.4)
MIN.
* Case : D2 Molded plastic
0.034 (0.86)
0.028 (0.71)
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
Dimensions in inches and ( millimeters )
* Mounting position : Any
* Weight : 0.465 gram
RATING
Maximum Recurrent Peak Reverse Voltage VRRM 70 400 600 Volts
Maximum RMS Voltage VRMS 49 280 420 Volts
Maximum Reverse Voltage VDC 70 400 600 Volts
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 55 °C
Peak Forward Surge Current,
8.3ms Single half sine wave Superimposed
on rated load (JEDEC Method) IFSM 50 Amps.
Maximum Peak Forward Voltage at IF = 1.0 A. VF 1.1 1.8 2.0 Volts
Maximum DC Reverse Current Ta = 25 °C
at Rated DC Blocking Voltage Ta = 100 °C
Maximum Reverse Recovery Time ( Note 1 ) Trr 35 ns
Typical Junction Capacitance ( Note 2 ) CJ 50 pf
Junction Temperature Range TJ - 65 to + 150
Storage Temperature Range TSTG - 65 to + 150
SYMBOL RG10Y RG10 RG10A UNITS
IF(AV) 1.5 1.2 1.0 Amp.
IR 5
IR(H) 50
µA
µA
°C
°C
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC
RATING AND CHARACTERISTIC CURVES ( RG10 - RG10Y )
+
100
150
806040
20
10
1.04005003020100.1
10
1.0
0.1
REVERSE CURRENT, MICROAMPERES
0
- 0.25
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
Ω
50 Vdc
(approx)
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
100
CURRENT Io (%)
PERCENTAGE AGAINST RATED
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75
AMBIENT TEMPERATURE, ( °C)
125
D.U.T.
1
Ω
10
Ω
+ 0.5 A
PULSE
GENERATOR
( NOTE 2 )
OSCILLOSCOPE
( NOTE 1 )
CURRENT, AMPERES
PEAK FORWARD SURGE
175 1 2 4 6 10 20 40 60 100
- 1.0 A
8.3 ms SINGLE HALF SINE WAVE
Trr
SET TIME BASE FOR 15 ns/cm
1 cm
Ta = 50 °C
NUMBER OF CYCLES AT 60Hz
100
FORWARD CURRENT, AMPERES
0.01
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
TJ = 100 °C
RG10Y
RG10A
RG10
Pulse Width = 300 µs
2% Duty Cycle
TJ = 25 °C
0.01
0 20 40 60
PERCENT OF RATED REVERSE
TJ = 25 °C
80
100 140
VOLTAGE, (%)
120
FORWARD VOLTAGE, VOLTS
Loading...