EIC GR1D, GR1B, GR1A, GR1M, GR1K Datasheet
...
GR1A - GR1M
GLASS PASSIVATED JUNCTION
FAST RECOVERY RECTIFIERS
PRV : 50 - 1000 Volts
FEATURES :
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
1.2 ± 0.2
5.0
±
0.15
2.1 ± 0.2
4.5
±
0.15
0.2 ± 0.07
Io : 1.0 Ampere
* Glass passivated chip
* High current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
* Case : SMA Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Lead Formed for Surface Mount
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.067 gram
SMA (DO-214AC)
2.6 ± 0.15
2.0 ± 0.2
Dimensions in millimeter
RATING
Maximum Recurrent Peak Reverse Voltage V
Maximum RMS Voltage V
Maximum DC Blocking Voltage V
Maximum Average Forward Current Ta = 55 °C
Peak Forward Surge Current,
8.3ms Single half sine wave superimposed
on rated load (JEDEC Method) I
Maximum Peak Forward Voltage at IF = 1.0 A V
Maximum DC Reverse Current Ta = 25 °C
at Rated DC Blocking Voltage Ta = 125 °C
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 ) C
Junction Temperature Range T
Storage Temperature Range T
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V
Page 1 of 2 Rev. 01 : April 17, 2002
SYMBOL GR1A GR1B GR1D GR1G GR1J GR1K GR1M UNIT
DC
RRM
RMS
F(AV)
I
FSM
I
R(H)
I
Trr
STG
DC
F
R
J
J
50 100 200 400 600 800 1000 V
35 70 140 280 420 560 700 V
50 100 200 400 600 800 1000 V
1.0 A
35 A
1.3 V
5
150
150 250 500 ns
15 pf
- 65 to + 150
- 65 to + 150
µA
µA
°C
°C
RATING AND CHARACTERISTIC CURVES ( GR1A - GR1M )
+
FORWARD VOLTAGE, VOLTS
1.0
+ 0.5 0- 0.25
- 1.0 A
1
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω 10 Ω
D.U.T.
50 Vdc
(approx)
1 Ω
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
OSCILLOSCOPE
( NOTE 1 )
PULSE
GENERATOR
( NOTE 2 )
Trr
SET TIME BASE FOR 50/100 ns/cm
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
30
24
18
12
CURRENT, AMPERES
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
6
PEAK FORWARD SURGE
AMBIENT TEMPERATURE, ( °C)
8.3 ms SINGLE HALF SINE WAVE
Ta = 50 °C
NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
20
10
Pulse Width = 300 µs
2% Duty Cycle
1.0
0.1
FORWARD CURRENT, AMPERES
0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
TJ = 25 °C
10
1.0
0.1
MICROAMPERES
REVERSE CURRENT,
0.01
TJ = 100 °C
TJ = 25 °C
80 100 1400 20 40 60 120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
Page 2 of 2 Rev. 01 : April 2, 2002
Loading...