EIC 1N4937G, 1N4936G, 1N4935G, 1N4934G, 1N4933G Datasheet
1N4933G - 1N4937G
GLASS PASSIVATED JUNCTION
FAST RECOVERY RECTIFIERS
PRV : 50 - 600 Volts
Io : 1.0 Amperes
FEATURES :
MECHANICAL DATA :
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Notes :
DO - 41
Dimensions in inches and ( millimeters )
* Glass passivated chip
* High current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
* Case : DO-41 Molded plastic
* Epoxy : UL94V-O rate flame retardant
* Lead : Axial lead solderable per MIL-STD-202,
Method 208 guaranteed
* Polarity : Color band denotes cathode end
* Mounting position : Any
* Weight : 0.34 gram
RATING
Maximum Recurrent Peak Reverse Voltage V
Maximum RMS Voltage V
Maximum DC Blocking Voltage V
Maximum Average Forward Current
0.375"(9.5mm) Lead Length Ta = 50 °C
Peak Forward Surge Current,
8.3ms Single half sine wave superimposed
on rated load (JEDEC Method)
Maximum Peak Forward Voltage at IF = 1.0 A V
Maximum DC Reverse Current Ta = 25 °C
at Rated DC Blocking Voltage Ta = 100 °C
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 ) C
Junction Temperature Range T
Storage Temperature Range T
SYMBOL 1N4933G 1N4934G 1N4935G 1N4936G 1N4937G UNIT
F(AV)
I
I
I
RRM
RMS
DC
FSM
R
I
R(H)
Trr
STG
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
50 100 200 400 600 V
35 70 140 280 420 V
50 100 200 400 600 V
1.0
30
F
J
J
1.2 V
5.0
100
150 ns
15 pf
- 65 to + 150
- 65 to + 150
1.00 (25.4)
MIN.
0.205 (5.2)
0.166 (4.2)
1.00 (25.4)
MIN.
A
A
µA
µ
°C
°
A
C
( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A.
( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 V
Page 1 of 2 Rev. 01 : April 17, 2002
DC
RATING AND CHARACTERISTIC CURVES ( 1N4933G - 1N4937G )
+
1.0
24
+ 0.5 0- 0.25
- 1.0 A
1
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω 10 Ω
Trr
D.U.T.
50 Vdc
(approx.)
1 Ω
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
OSCILLOSCOPE
( NOTE 1 )
PULSE
GENERATOR
( NOTE 2 )
SET TIME BASE FOR 50-100 ns/cm
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
30
8.3 ms SINGLE HALF SINE WAVE
Ta = 50 °C
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
60Hz RESISTIVE OR INDUCTIVE LOAD
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
AMBIENT TEMPERATURE, ( °C)
CURRENT, AMPERES
PEAK FORWARD SURGE
NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
20
10
Pulse Width = 300 µs
1.0
0.1
2% Duty Cycle
TJ = 25 °C
10
TJ = 100 °C
1.0
0.1
TJ = 25 °C
FORWARD CURRENT, AMPERES
0.01
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
FORWARD VOLTAGE, VOLTS
0.01
0
REVERSE CURRENT, MICROAMPERES
40 60 120
20
80
100
PERCENT OF RATED REVERSE
140
VOLTAGE, (%)
Page 2 of 2 Rev. 01 : April 2, 2002
Loading...