EHongLight Amazing B eye Par User Manual

1 / 15

Amazing B eye Par

ZOOM and Rotation

19pcs 15W 4-in-1

User Manual

KEEP THIS MANUAL FOR FUTURE NEEDS

2 / 15

1. Unpacking

Thank you for choosing our B eye par. For your own safety, please read this manual
before installing the device. This manual covers the important information on
installation and applications. Please install and operate the fixture with following
instructions. Meanwhile, please keep this manual well for future needs.

This fixture is made of a new type of high temperature strength of engineering plastics
and cast aluminum casing with nice outlook. The fixture is designed and manufactured
strictly following CE standards, complying with international standard DMX 512
protocol. It’s available independently controlled and linkable with each other for
operation. And it is applicable for large-scale live performances, theater, studio,
nightclubs and discos.

4-IN-1 LEDs (RGBW) which features high brightness and stability. Please carefully
unpack it when you receive the fixture and check whether it is damaged during the
transportation. And please check whether the following items are included inside the
box:

LED Par--------One Signal Cable--------One

Power Cable--------One Safety Cable--------one

User Manual--------One

3 / 15

2. Safety Instructions

This device has left the factory in perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes due to environmental
changes, do not switch it on immediately. The arising condensation could damage the
device. Leave the device switched off until it has reached room temperature.

This device falls under protection-class I. Therefore it is essential that the device be
earthed.

The electric connection must carry out by qualified person.

The device shall only be used with rate voltage and frequency.

Make sure that the available voltage is not higher than stated at the end of this
manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would
be the case, replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it.
Only handle the power cord by the plug. Never pull out the plug by tugging the power
cord.

During initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

Fixtures cannot be installed on combustible substances, keep more than 50cm
distance with wall for smooth air flow, so there should be no shelter for fans and
ventilation for heat radiation.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order
to avoid a hazard.

4 / 15

3. Operation Instructions

-The LED par is for wash effect for on-site decoration purpose.

-Don’t turn on the fixture if it’s been through severe temperature difference like after
transportation because it might damage the light due to the environment changes. So
make sure to operate the fixture until it is in normal temperature.

-This light should be keep away from strong shaking during any transportation or
movement.

-Don’t pull up the light by only the head, or it might cause damages to the mechanical
parts.

-Don’t expose the fixture in overheat, moisture or environment with too much dust
when installing it. And don’t lay any power cables on the floor. Or it might cause
electronic shock to the people.

-Make sure the installation place is in good safety condition before installing the fixture.

-Make sure to put the safety chain and check whether the screws are screwed properly
when installing the fixture.

-Make sure the lens are in good condition. It’s recommended to replace the units if
there are any damages or severe scratch.

-Make sure the fixture is operated by qualified personnel who knows the fixture before
using.

-Keep the original packages if any second shipment is needed.

-Don’t try to change the fixtures without any instruction by the manufacturer or the
appointed repairing agencies.

-It is not in warranty range if there are any malfunctions from not following the user
manual to operate or any illegal operation, like shock short circuit, electronic shock,
lamp broke, etc.

4. Mounting and Installation

Cautions: For added protection mount the fixtures in areas outside walking paths,
seating areas, or in areas were the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any surface, make sure that the installation area can
hold a minimum point load of 10 times the device’s weight.

Fixture installation must always be secured with a secondary safety attachment, such

as an appropriate safety cable.

5 / 15

Never stand directly below the device when mounting, removing, or servicing the
fixture from a periodic safety inspection of all installation material and the fixture. If you
lack these qualifications, do not attempt the installation yourself. Improper installation
can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.

Clamp Mounting: The B eye par provides a unique mounting bracket assembly that
integrates the bottom of the base, and the safety cable rigging point in one unit (see
the illustration below). When mounting this fixture to truss be sure to secure an
appropriately rated clamp to the included omega bracket using a M10 screw fitted
through the center hole of the “omega bracket”. As an added safety measure be sure
to attached at least one properly rated safety cable to the fixture using on of the safety
cable rigging point integrated in the base assembly

Regardless of the rigging option you choose for your B eye par, always be sure to
secure your fixture with a safety cable. The fixture provides a built-in rigging point for a
safety cable on the hanging bracket as illustrated above. Be sure to only use the
designated rigging point for the safety cable and never secure a safety cable to a
carrying handle.