EGO HT6500E Operator's Manual

WARNING: To reduce the risk of injury, the user must read and understand the

Operator’s Manual before using this product. Save these instructions for future reference.

OPERATOR’S MANUAL

56 VOLT LITHIUM-ION

CORDLESS HEDGE TRIMMER

MODEL NUMBER HT6500E

D

B C

1

2

E1

4. Rear Switch Lever

5. Speed

Adjustment Knob

6. Front Handle

7. Front Switch Lever

8. Hand Guard

3. Lock-off Trigger

2. Rear Handle

1. Battery-release Button

9. Blade Guard

12. Latch

A

10. Blade

11. Tip Protector

13. Electric
Contacts

14. Mounting Slot

16. Lock for Handle

15. Ejection Mechanism

17. Motor Housing

18. Shield

F2 F3

F4

E2 F1

0°

+45° +90°

-45°

F5

-90°

G H

Blade Guard

Blade

56 VOLT LITHIUM-ION CORDLESS HEDGE TRIMMER — HT6500E4

READ ALL INSTRUCTIONS!

READ & UNDERSTAND
INSTRUCTION MANUAL

Residual risk! People with electronic devices, such

as pacemakers, should consult their physician(s) before
using this product. Operation of electrical equipment
in close proximity to a heart pacemaker could cause
interference or failure of the pacemaker.

WARNING: To ensure safety and reliability, all

repairs and replacements should be performed by a
qualied service technician.

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention
to possible dangers. The safety symbols and the expla­nations with them deserve your careful attention and un­derstanding. The symbol warnings do not, by themselves,
eliminate any danger.
The instructions and warnings they give are no substitutes
for proper accident prevention measures.

WARNING: Be sure to read and understand all

safety instructions in this Operator’s Manual, including all
safety alert symbols such as “DANGER,” “WARNING,”
and “CAUTION” before using this tool. Failure to follow all
instructions listed below may result in electric shock, re,
and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER,

WARNING, or CAUTION. May be used in conjunction with

other symbols or pictographs.

WARNING:

The operation of any power tools can
result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power
tool operation, always wear safety goggles or safety glasses
with side shields and a full face shield when needed. We
recommend a Wide Vision Safety Mask for use over eye­glasses or standard safety glasses with side shields.

SAFETY INSTRUCTIONS

This page depicts and describes safety symbols that may
appear on this product. Read, understand, and follow
all instructions on the machine before attempting to
assemble and operate.

Safety Alert

Indicates a potential personal
injury hazard.

Read The
Operator’s
Manual

To reduce the risk of injury,
user must read operator’s
manual.

65cm

Blade Length The length of the blade

Ø33 mm

Cutting
Capacity

Max. Cutting capacity of the
blade

72

NOISE dB

Noise

Guaranteed sound power
level.

IPX4

Ingress Protec­tion Degree

Protection from splashing
water

V Volt Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

min Minutes Time

Alternating
Current

Type of current

Direct Current

Type or a characteristic of
current

n

0

No Load Speed Rotational speed, at no load

... /min Per Minute Revolutions per minute

SPM

Strokes Per
Minute

Stroke speed, at no load

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings and

instructions. Fail to follow the warnings and instructions
may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.