E.F. Johnson 9883, 9800 Series Service Manual

Download

Page 1

SERVICE MANUAL

ADDENDUM

Second Printing

January 2001

Supersedes 001-9800-500, 2/00

9883 800 MHZ MOBILE

SMARTNET™/SMARTZONE®/CONVENTIONAL

13.6 VDC, 15 or 30 Watts 806-824 MHz Transmit 851-870 MHz Receive Part No. 242-98xx-30x/-50x

SMARTNET™/SMARTZONE®/CONVENTIONAL MOBILE

Page 2

98xx Series

SMARTNET

Service Manual Addendum

13.6 VDC, 806-824 MHz Transmit, 851-870 MHz Receive Part No. 242-9883-3xx (SMARTNET Only)

Part No. 242-9883-5xx (SMARTNET/ SmartZone)

™

/SmartZone®/Conventional

FM Mobile Radio

The E.F. Johnson Company, which was founded in 1923, provides wireless communication systems solutions for public safety, government, and commercial customers. The company designs, manufactures, and markets conventional and trunked radio systems, mobile and portable subscriber radios, repeaters, and Project 25 digital radio products.

V iki ng He ad/ EFJohnson logo, Call Guard E.F. Johnson Company. SMARTNET versation pany and/or product names used in this manual are trademarks and/or registered trademarks of their respective manufacturer.

Information in this manual is subject to change without notice.

™

, and Private Conversation II™ are trademarks of Motorola, Inc. All other com-

, PCTrunk™, and PCTune™ are trademarks of the

™

, SmartZone®, Call Alert™, Enhanced Private Con-

Page 3

TABLE OF CONTENTS

1 GENERAL INFORMATION

1.1 SCOPE OF MANUAL . . . . . . . . . . . . . . . . . . . .1-1

1.2 DIFFERENCES BETWEEN LTR AND SMARTNET/SMARTZONE VERSIONS

Hardware Differences. . . . . . . . . . . . . . . . . . . . . 1-1

Software Differences . . . . . . . . . . . . . . . . . . . . . 1-1

1.3 TRANSCEIVER IDENTIFICATION. . . . . . . . .1-1

1.4 PART NUMBER BREAKDOWN. . . . . . . . . . .1-1

1.5 MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . .1-2

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Key Cap Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Systems, Channels, and Zones . . . . . . . . . . . . . . 1-2

NPSPAC Models . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Transceiver Alignment . . . . . . . . . . . . . . . . . . . . 1-3

. . .1-1

2 OPERATION

2.1 FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

General Features . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Conventional Features . . . . . . . . . . . . . . . . . . . . 2-1

SMARTNET SmartZone

2.2 CONTROLS AND DISPLAY . . . . . . . . . . . . . .2-1

Rear Panel Jacks and Connectors . . . . . . . . . . . . 2-2

Display Description . . . . . . . . . . . . . . . . . . . . . . 2-2

2.3 GENERAL OPERATION . . . . . . . . . . . . . . . . .2-3

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Turning Power On and Setting Volume . . . . . . . 2-3

Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Option Switches . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Channel and Zone Selection . . . . . . . . . . . . . . . . 2-3

Home Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Time-Out Timer . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Tone Enable/Disable. . . . . . . . . . . . . . . . . . . . . . 2-4

Power Turn-Off Delay . . . . . . . . . . . . . . . . . . . . 2-4

Temperature and Voltage Monitoring . . . . . . . . 2-5

Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Conventional and SMARTNET/Smar tZone

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.4 CONVENTIONAL FEATURES . . . . . . . . . . . .2-8

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Display Mode Selection . . . . . . . . . . . . . . . . . . . 2-8

Monitoring Before Transmitting. . . . . . . . . . . . . 2-8

Monitor Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

Busy Channel Lockout . . . . . . . . . . . . . . . . . . . . 2-8

Call Guard Squelch. . . . . . . . . . . . . . . . . . . . . . . 2-9

Penalty Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

Conversation Timer . . . . . . . . . . . . . . . . . . . . . . 2-9

Repeater Talk-Around . . . . . . . . . . . . . . . . . . . . 2-9

™

II Features . . . . . . . . . . . . . . . . . 2-1

Features . . . . . . . . . . . . . . . . . . . . . 2-1

Power Output Select . . . . . . . . . . . . . . . . . . . . . . 2-9

Conventional Mode Scanning. . . . . . . . . . . . . . 2-10

Priority Channel Sampling . . . . . . . . . . . . . . . . 2-10

Standard Conventional Calls. . . . . . . . . . . . . . . 2-11

DTMF/ANI Signaling . . . . . . . . . . . . . . . . . . . . 2-11

2.5 SMARTNET/SMARTZONE FEATURES . . 2-11

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Viewing Unit ID . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Standard Group Calls . . . . . . . . . . . . . . . . . . . . 2-12

Enhanced Private Conversation Calls. . . . . . . . 2-12

Private Conversation II Calls . . . . . . . . . . . . . . 2-14

Telephone Calls. . . . . . . . . . . . . . . . . . . . . . . . . 2-15

Call Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Sending Status Conditions . . . . . . . . . . . . . . . . 2-16

Emergency Alarm and Call. . . . . . . . . . . . . . . . 2-17

Failsoft Operation . . . . . . . . . . . . . . . . . . . . . . . 2-17

SMARTNET/SmartZone Scanning. . . . . . . . . . 2-17

Dynamic Regrouping . . . . . . . . . . . . . . . . . . . . 2-18

SmartZone Features. . . . . . . . . . . . . . . . . . . . . . 2-18

2.6 SUPERVISORY TONES . . . . . . . . . . . . . . . 2-19

3 PROGRAMMING

3.1 GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Programming Setup. . . . . . . . . . . . . . . . . . . . . . . 3-1

Computer Description. . . . . . . . . . . . . . . . . . . . . 3-1

PCTrunk Software Installation . . . . . . . . . . . . . . 3-1

Connecting RPI To Computer and Transceiver . 3-2

Starting and Exiting. . . . . . . . . . . . . . . . . . . . . . . 3-2

Programming File Types. . . . . . . . . . . . . . . . . . . 3-2

Help Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Screen Groups. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Displaying Screens . . . . . . . . . . . . . . . . . . . . . . . 3-3

File Size Indicator . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Creating and Displaying Systems . . . . . . . . . . . . 3-4

3.2 PROGRAMMING PROCEDURE. . . . . . . . . . 3-4

Preliminary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Programming Radio Wide Parameters . . . . . . . . 3-4

Programming Conventional Channels . . . . . . . . 3-4

Programming SMARTNET and SmartZone

Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Programming Radio (Downloading File) . . . . . . 3-5

3.3 MENU COMMANDS . . . . . . . . . . . . . . . . . . . . 3-5

File Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Radio Series Menu . . . . . . . . . . . . . . . . . . . . . . . 3-6

Download Menu . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Upload Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Systems Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Tools Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Window Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Help Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Revised January 2001 Part No. 001-9800-501

Page 4

TABLE OF CONTENTS (CONT’D)

TABLE OF CONTENTS

3.4 RADIO-WIDE PARAMETER SCREENS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Radio-Wide General screen . . . . . . . . . . . . . . . . 3-7

Radio-Wide Conventional Screen . . . . . . . . . . . 3-8

Radio-Wide SMARTNET/SmartZone Screen . . 3-8

Radio-Wide Mobile Options Screen . . . . . . . . 3-10

3.5 PROGRAMMING CONVENTIONAL

SYSTEMS AND CHANNELS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10

Conventional System General Screen . . . . . . . 3-10

Setting Up Conventional Channels . . . . . . . . . 3-12

Conventional Channel Screen Parameters . . . . 3-13

3.6 PROGRAMMING SMARTNET/SMARTZONE

SYSTEMS AND CHANNELS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

SMARTNET/SmartZone System Screens

General Screen . . . . . . . . . . . . . . . . . . . . . . . 3-14

Other ID’s Screen. . . . . . . . . . . . . . . . . . . . . 3-15

Phone Interconnect Screen. . . . . . . . . . . . . . 3-16

Talk Groups Screen . . . . . . . . . . . . . . . . . . . 3-16

Emergency Settings Screen . . . . . . . . . . . . . 3-17

SMARTNET/SmartZone System Lists Screens 3-18 Setting Up SMARTNET/SmartZone Channels 3-22 SMARTNET/SmartZone Channel Screen

Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22

. . . . . . . . . . .3-10

. . . . . . . . . . .3-14

. . . .3-7

4 ALIGNMENT AND PERFORMANCE

TESTS

5 DSP BOARD SERVICING

INFORMATION

98xx Audio/Logic Board Part Changes . . . . . . . 5-1

98xx RF Board Part Change. . . . . . . . . . . . . . . . 5-1

DSP Board Parts List . . . . . . . . . . . . . . . . . . . . . 5-1

DSP Board Connections To Audio/logic Board. 5-3

Revised DSP Board Component Layout. . . . . . . 5-4

Revised DSP Board Schematic Diagram . . . . . . 5-5

Unrevised DSP Board Schematic Diagram . . . . 5-6

Unrevised DSP Board Component Layout. . . . . 5-7

LIST OF FIGURES

2-1 Front Panel Controls And Indicators . . . . . . . . . 2-1

3-1 Programming Setup . . . . . . . . . . . . . . . . . . . . . . 3-1

3-2 Main Screen (Later PCTrunk Versions). . . . . . . 3-3

3-3 Conventional Channel Screen . . . . . . . . . . . . . . 3-13

3-4 SMARTNET/SmartZone Channel Screen . . . . 3-21

4-1 Alignment Setup . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4-2 PCTune Main Screen . . . . . . . . . . . . . . . . . . . . . 4-3

4-3 Tune Parameters Screen . . . . . . . . . . . . . . . . . . . 4-3

4-4 Alignment Points Diagram . . . . . . . . . . . . . . . . . 4-4

4.1 GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Test Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Tune Software . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Preliminary Setup. . . . . . . . . . . . . . . . . . . . . . . . 4-2

Reading Current Settings . . . . . . . . . . . . . . . . . . 4-3

4.2 TRANSMIT POWER OUTPUT . . . . . . . . . . . .4-3

4.3 FREQUENCY SET/VCO CHECK. . . . . . . . . .4-4

4.4 TRANSMIT MODULATION . . . . . . . . . . . . . . .4-4

4.5 RECEIVER IF ALIGNMENT AND CHECK. .4-5

4.6 SQUELCH ADJUSTMENT . . . . . . . . . . . . . . .4-5

4.7 RSSI ADJUSTMENT . . . . . . . . . . . . . . . . . . . .4-5

4.8 PERFORMANCE TESTING . . . . . . . . . . . . . .4-5

LIST OF TABLES

1-1 98xx Accessories . . . . . . . . . . . . . . . . . . . . . . . . .1-2

2-1 Option Switch Functions . . . . . . . . . . . . . . . . . . .2-4

3-1 Call Guard (CTCSS/DCS) Codes and Tones . . .3-23

Revised January 2001

iii

Part No. 001-9800-501

Page 5

SECTION 1 GENERAL INFORMATION

GENERAL INFORMATION

1.1 SCOPE OF MANUAL

This addendum updates the following LTR® 9800-series service manual with the additional information needed to service 9800-series SMARTNET™/ SmartZone

transceivers.

98xx Series UHF/800/900 MHz Service Manual,

Part No. 001-9800-001

1.2 DIFFERENCES BETWEEN LTR AND

SMARTNET/SMARTZONE VERSIONS

1.2.1 HARDWARE DIFFERENCES

The 98xx SMARTNET/SmartZone transceivers use the same basi c P C boa rds an d mechanical package used for high tier LTR models. The only change is the addition of a DSP board that mounts on top of the current audio/logic board. This DSP board provides the SMARTNET/SmartZone control and signal processing functions.

Therefore, use the service manual listed above to service all boards except the DSP board. Service and interfacing information for that board is located in Section 5 of this addendum.

1.2.2 SOFTWARE DIFFERENCES

The audio/logic and DSP board operating software (firmware) is unique to this transceiver. In addition, the pr ogramming and tuning software is also different. Therefore, new Operation, Programming, and Alignment sections are included in this manual.

The programming and tuning programs are now Windows

based. Therefore, Windows 95, 98, or NT 4 or later is required to run these programs. The programming software is called PCTrunk alignment software is called PCTune

™

. Refer to

, and the

Sections 1.5.5 and 1.5.6 for more information on programming and alignment.

1.3 TRANSCEIVER IDENTIFICATION

The transceiver identification (serial) number is printed on a label that is attached to the chassis. The information contained in this number is as follows.

PlantFrom P.N.

A = Waseca

Warranty

Number

Model Revision

Letter

98xx A

A 02 0 A 12345

Manufacture

Date

Type

A = SMARTNET/

SmartZone

Last Digit of Year

Week No. of Year

1.4 PART NUMBER BREAKDOWN

The following is a breakdown of the part number

used to ident ify this transceiver.

242 - 9 8 x x -x x x x

Band

1 = VHF* 4 = UHF 8 = 800 MHz 9 = 900 MHz

Type

1 = Low tier, dual BW 2 = Mid tier, dual BW* 3 = High tier, dual BW 4 = Low tier, 12.5 kHz 5 = Mid tier, 12.5 kHz* 6 = High tier, 12.5 kHz 8 = High tier rem, dual BW 0 = High tier rem, 12.5 kHz

Signaling 2 = LTR 3 = SMARTNET 4 = Multi-Net 5 = SmartZone 6 = LTR-Net 8 = Data LTR 9 = Data Multi-Net 0 = Conv only*

NOTES:

1. * These configurations are currently not available.

2. Mid power = 25W UHF, 15W 800/900 MHz;

High power = 40W UHF, 30W 800/900 MHz

Options [1]

B/N = Comp/Data C/O = Compander D/P = Data Cable E/Q = Enc/Comp F/T = Enc/C o mp/Dat G/U = Comp/Acsry H/V = Horn/Acsry I/W = Enc/Comp/

Acsry Cable

[1] N-W models are LTR-Net upgradable

Config.

1 = Low Pwr std* 2 = Mid Pwr std 3 = High Pwr std 6 = Low Pwr std* 7 = M.P. no acc 8 = H.P. no acc

Freq Range

0 = Full band (800/

900 MHz) 3 = 430-470 MHz 5 = 470-512 MHz

1-1

Revised January 2001

Part No. 001-9800-501

Page 6

GENERAL INFORMATION

1.5 MISCELLANEOUS

1.5.1 ACCESSORIES

T abl e 1-1 i s a parti al l isti ng of acce ssori es t hat a re available for 9800-se ries transceivers. Refer to this table in the service manual for other accessories that are available.

Table 1-1 98xx Accessories

Accessory Part No.

Optional SMARTNET/SmartZone key cap kit (see Section 1.5.2)

Programming Accessories

Remote Programming Interface (RPI) 023-9800-000 Cable, RPI to transceiver 597-2002-200 Cable, RPI to computer, 6 ft.

(DB9F to DB9M)

PCTrunk personality programming

software, Win 95/NT, CD-ROM

PCTune alignment software (see Section

1.5.6)

587-9840-105

597-5900-002

023-9998-453

Contact Cust. Service

1.5.3 SYSTEMS, CHANNELS, AND ZONES

A zone and channel are selected to place and receive calls. The following describes the relationship between systems, channels, and zones.

Systems

A system as used with this transceiver is a collection of channels (talk groups) belonging to the same repeater site. A system defines all the parameters and protocol definitions required to access a site. Up to 1 conventional system and 15 SmartNet/SmartZone systems can be programmed (16 total). Systems are used for programming purposes only and are not selectable by the user.

Channels

A channel selects a radio channel or talk group in a system as follows:

Conventional Mode - A channel selects a specific radio channel, Call Guard (CTCSS/DCS) squelch coding, and other parameters unique to that channel.

1.5.2 KEY CAP KITS

Key Cap Kit, Part No. 587-9840-003, is included with each transceiver. This kit includes the five key caps listed below.

EMER F1 F2 F3 SCAN

Optional Key Cap Kit, Part No. 587-9840-105, is also available. This kit includes the key caps shown below.

F1 F2 F3 F4 SCAN BKLHT MSG HORN C/S DISP PRIED SELSQ MON TGSEL PHONE RESP NUIS STATUS TXPWR (Blank) ALERT EMER RWS TONES (Blank)

T o re move a key cap, i nsert a tool with a s harp ti p in the slot on the bottom of the cap and carefully pry against the front panel to release the cap.

SmartNet/SmartZone Mode - A channel selects a specific talk group, announcement group, emergency group, and other parameters unique to that channel.

As previously describ ed, a maximu m of up to 256 channels can be programmed with the preceding modes. The conventional system can be programmed with up to 256 channels, and each SmartNet/SmartZone system can be programmed with up to 256 talk groups (channels).

Therefore it is theoretically possible to program any combination of these systems that produces up to 256 total channels. However, the maximum number may be limited by the availa ble memory. For example, since more memory is requir ed to pr ogram a Smar tNet system than a conv entional sy stem, the total nu mber of channels decreases as the number of Smart Net systems increases. The programming software displays a bar graph which shows the amount of available memory space that is used by the current data. Refer to Section

3.1.10 for more inform ation.

Revised January 2001 Part No. 001-9800-501

1-2

Page 7

GENERAL INFORMATION

Zones

A zone is a collection of up to 16 chann els of any type (conventional or SmartNet/SmartZone). For example, a zone could include 12 conventional channels and 4 S martNet channels. Zones are similar to banks used in other EFJohnson transceivers. One use of zones may be to program the channels used for operation in a specific geographical area. Up to 16 zones can be programmed.

1.5.4 NPSPAC MODELS

All 800 MHz models meet the stricter specifications estab lished by NP SPAC (National Public Safety Panel Advisory Committee) for public safety frequencies from 821-824 and 866-869 MHz. Maximum deviation on NPSPAC channels is 4 kHz, and it is automatically changed to the level set for NPSPAC channels when one of these channels is selected.

1.5.5 PROGRAMMING

The transceiver is programmed using a PCcompatible computer, the EFJohnson Remote Programming Interface (RPI), and the PCTrunk™ programming software (see Table 1-1). Programming is described in Section 3. The operating software (firmware) is Flash upgradable if required. Keypad programming is not available with this transceiver.

1.5.6 TRANSCEIVER ALIGNMENT

Transceiver alignment is performed using the same computer and RPI used to perform programming (see preceding section) and special PCTune™ software. Only three adjustments are made manually and the rest are made electronically using the PCTune software. Therefore, if the manual adjustments do not require readjustment, the transceiver can be tuned without removing the top cover to access internal adjustments. Refer to Section 4 for more information.

1-3

Revised January 2001

Part No. 001-9800-501

Page 8

SECTION 2 OPERATION

OPERATION

EMER

Microphone

Jack

2.1 FEATURES

Option Switches

On-Off/Volume

(Press/Rotate)

Figure 2-1 Front Pan el Controls And Indicators

Select Switch

(Press/Rotate)

SCAN

2.1.3 SMARTNET™ II FEATURES

Speaker

2.1.1 GENERAL FEATURES

• Up to 16 zones with home zone select

• Up to 16 channels per zone (256 channels total)

• Standard and radio-wide scan

• Five programmable option switches

• Time-out timer

• 16-character LCD alphanumeric display with

8 status annunciators

2.1.2 CONVENTIONAL FEATURES

• Up to 256 channels programmable

• Scanning with three user programmable scan lists

• Priority channel sampling when scanning

• Busy channel lockout (transmit disable on busy)

• Monitor mode

• Call Guard

control

(CTCSS/DCS) or carrier squelch

• Penalty and conversation timers

• Repeater talk-around

• DTMF/ANI signaling

• User selectable high and low power output

• Up to 256 talk groups programmable

• Group, Enhanced Private Conversation

Conversa tion II

• Call Alert

™

(paging)

™

, and telephone Calls

™

, Private

• Emergency alarms and calls

• Messaging

• Priority monitor scanning with user programmable

scan lists

• Failsoft operation

• Dynamic regrouping

2.1.4 SMARTZONE® FEATURES

• Site trunking

• Site search

• Site lock/unlock

2.2 CONTROLS AND DISPLAY

On-Off Volume - Pressing this knob turns power on and off, and rotating it sets the speaker volume (see Section 2.3.2).

2-1

Revised January 2001

Part No. 001-9800-501

Page 9

OPERATION

Select Switch - Rotating this switch increases or decreases the se le ct ed channel. It is also used for ot her functions such as selecting the zone and scrolling through lists. See Section 2.3.5 for more information.

Option Switches - The five fron t panel option switch es can be programmed for various functions. Refer to Section 2.3.4 for more information.

Transmit/Busy Indicator - Indicates the fo llowing conditions:

Red

- Transmitter is keyed

Green

- The currently selected receive cha nnel may

be busy because a carrier (signa l) is be ing detected (see Section 2.4.3).

Microphone Jack - Connection point for the microphone.

Microphone Push-To-Talk (PTT) Switch - Pushbutton on the microphone which is pressed to key the transmitter.

is automatically disabled when a speaker is plugged into this jack.

Accessory Cable (Not Shown) - This optional pigtail cable installs in the speaker jack opening and is used to connect the ignition sense input and other outputs.

2.2.2 DISPLAY DESCRIPTION

Std Scan

Enabled

In Scan

List

Radio-

Wide Scan

Priority

Channel

Keypad

Prg Mode

Speaker - The internal speaker is located behind the grille. An optional speaker can be connected to the external speaker j ack located on the ba ck. See “Speaker Jack” description in next section for more information.

Antenna

Jack

2.2.1 REAR PANEL J ACKS AND CONNECTORS

Antenna Jack - Miniature UHF ja ck for connecting the 50-ohm antenna.

Power Jack - Connection point for the power cable which attaches to t he vehicle battery . A n ominal 12-volt DC, negative ground power source is required.

Speaker Jack - Connection point for an optional external 4.7-ohm, 5-watt speake r. The internal speaker

Power

Jack

Ext. Speaker

Jack

Upper and Lower

8-Character Displays

Upper 8-Character Display - This alphanumeric display indicates the channel alias or information about the selected mode. With conventi ona l operation, it may also indicate the channel number or frequency (see Section 2.4.2).

Lower 8-Character Display - This alphanumeric display indicates additional information pertaining to the current mode when necessary.

- Indicates that standard scanning is enabled (see

Section 2.3.11). Standard and radio wide scanning cannot be enabled at the same time.

- The box around the “S” indic ates t hat the cur rent conventional or SMARTNET/SmartZone channel is in the standard scan list (Section 2.3.11).

- With SMARTNET/SmartZone channels only, indicates that the telephone (interconnect) mode is selected (Section 2.5.6).

Talk-Around

Mode

Telephone Call

Private

Call

Monitor

Mode

Revised January 2001 Part No. 001-9800-501

2-2

Page 10

OPERATION

- Indicates that radio-wide scan is enabled (see

Section 2.3.11).

- Indicates that repeater talk-around is enabled on

the selected conventional channel (see Section 2.4.9).

- Indicates that a SMARTNET/SmartZone private

call is occurring (Sections 2.5.4 and 2.5.5).

- Indicates that the conventional monitor mode is

enabled (Section 2.4.4).

- Indicates that the s elected conve ntional channel i s

a priority channel (Section 2.4.12).

2.3 GENERAL OPERATION

2.3.1 INTRODUCTION

This section (2.3) describes features available with both conventional and SMARTNET/SmartZone (trunked) operation. For information on features unique to conventional channels, refer to Section 2.4, and for information on features unique to SMARTNET/SmartZone channels, refer to Section 2.5.

2.3.2 TURNING P OWER ON AND SETTING

VOLUME

Power is turned on and off by pressing the OnOff/Volume switch on the front panel. When power is initially turned on, an alert tone sounds and the radio software version is momentarily displayed. The zone alias is then displayed followed by the unit ID if a SMARTNET/SmartZone channel is selected (see Section 2.5.2). The selected channel is then indicated. When power is turned off, the display may remain on for a few seconds. It is recommended that power not be turned back on again until the display is blank.

• If a conventional channel is selected and the

Monitor option switch is programmed (see Section

2.4.4), pressing that switch unsquelches/squelches the receiver and eithe r voice or backgroun d noise is heard. If a SMARTNET/SmartZone channel is selected, the receiver cannot be manually unsquelched.

2.3.3 BACKLIGHT

The backlight for the display and keypad can be manually turned on and off if the Backlight option switch is programmed. Pressing this switch cycles between the Bright, Dim, and Of f modes. If this switc h is not programmed, the backlight is fixed in one of these modes.

2.3.4 OPTION SWITCHES

All five push-button switches on the front panel are programmable for the functions indicated in Table 2-1. If your radio is programmed with both conventional and SMARTNET/SmartZone channels (see Section 2.3.12), these option switches can be programmed to control a different set of functions for each channel type. For example, a switch could select the Monitor Mode when a conventional channel is selected and Private Cal ls whe n a SMARTNET/SmartZone channel is selected. If no option switch has been programmed to control a particular function, that function may not be available or in a fixed mode.

2.3.5 CHANNEL AND ZONE SELECTION

Channel Select

To change the selected channel, rotate the Select switch. The selected channel alias (name) is indicated on the top line of the display. With conventional channels, the channel number or frequency may also be displayed as described in Section 2.4.2.

The volume level is adjusted by rotating the OnOff/Volume switch. The relative volume level can be determined by noting the position of the index on the knob. You may also be able to enable a reference tone for setting the volume as follows:

• If key press tones ar e en abl ed ( see Section 2.3.8), a

short tone sounds when front panel option keys are pressed.

Zone Select

A zone is a group of up to any 16 conventional and SMARTNET/SmartZone channels defined by programming (see Section 1.5.3). Up to 16 zones can be programmed for a total of 16 x 16 or 256 channels. One use of zones may be to select groups of channels programmed for operation in different geographical areas or radio systems. Zones are selected as follows:

Revised January 2001

2-3

Part No. 001-9800-501

Page 11

OPERATION

1. Press the Zone op tion switch and the alias (n ame) of the current zone is indi cated on the upper line of the display.

2. Rotate the Select s witch to dis play the des ired zone. Then to select that zone and exit this mode, pre ss the Select switch or wait 4 seconds.

Table 2-1 Option Switch Functions

Function

[Sugg. Sw. Label]

Backlight [BKLHT] X X X 2.3.3 Call Alert [ALERT] X X 2.5.7 Call Response [RESP] X X 2.5.4, 2.5.5 Displayed Information

[DISP] Emergency [EMER] X X 2.5.10 High/Low Power

[TxPWR] Home Zone X X X 2.3.6 Message [MSG] X X 2.5.8 Monitor [MON] X 2.4.4 Normal/Selective

[SELSQ] Phone [PHONE] X X 2.5.6 Priority Edit [PRIED] X 2.4.12 Private Call X X 2.5.4, 2.5.5 Radio Wide Scan

[RWS] Repeater Talk-Around X 2.4.9 Scan [SCAN] X X X 2.3.11 Scan Edit X X X 2.4.11 Site Lock X 2.5.14 Site Search X 2.5.14 Status [STATUS] X X 2.5.9 Tones On-Off [TONES] X X X 2.3.8 Zone X X X 2.3.5

Conv. Mode

Smart

Mode

X 2.4.2

X2.4.10

X 2.4.6

X X X 2.3.11

Net

Smart-

Zone

Mode

See

Section

zone. To select the home zone, simply press this switch. Then to change the home zone to the currently selected zone, press and hold this switch until a tone sounds (approximately 1 second).

2.3.7 TIME-OUT TIMER

The time-out timer disables the transmitter if it is keyed for longer than the programmed time. It can be programmed on each channel for times from 15 seconds up to 3 minutes, 45 seconds or disabled (not used). If the transmitter is keyed continuously for longer than the programmed time, the transmitter is disabled and an invalid condition tone sounds. Five seconds before time-out occurs , an alert to ne sounds to indicate that time-out is approaching. The timer and tone are reset by releasing the PTT switch.

One use of this feature is to prevent a channel from being kept busy for an extended period by an accidentally keyed transmitter. It can also prevent possible transmitt er damage c aused by t ransmitti ng for an excessively long period. Conven tional cha nnels can also be programmed with the Penalty and Conversation timers that are described in Sections 2.4.7 and

2.4.8.

2.3.8 TONE ENABLE/DISABLE

The supervisory tones (see Section 2.6) can be enabled and disabled by the Tones On-Off option switch if it is programmed. When tones ar e enabl ed by this switch, “TONE ON” is momentarily displayed on the lower line and a tone sounds. Conversely, when tones are disabled, “TONE OFF” is displayed and no tone sounds. If the Tones On-Off option switch is not programmed, tones are fixed in the on or off mode by programming.

2.3.9 P OWER TURN-OFF DELAY

2.3.6 HOME ZONE

The radio can be programmed with a home zone. Then when power is turned on, the radio can be programmed so that either the home zone or last selected zone is automatically selected.

If the Home Zone option switch is programmed, it can be used to quickly select or change the home

Revised January 2001 Part No. 001-9800-501

The transceiver can be installed so that the vehicle ignition switch as well as the front-panel power switch controls transceiver power. This is done by connecting the accessory ignition switch wire to a power source switched by the ignition switch. Power off delays of 0-254 minutes or Forever can then be programmed. This delay ca n be overr idden at any time by turning power off using the front-panel power switch or turning the ignition switch back on.

2-4

Page 12

OPERATION

A turn-off delay allows the radio to remain active for the programmed delay time after the ignition swi tch is turned off. At the same ti me, advanta ges of ignition switch control can be utilized such as preventing battery discharge that may occur if the transceiver is accidentally left on for an extended period.

2.3.10 TEMPERATURE AND VOLTAGE

MONITORING

Excessive Transceiver Temperature

If the internal transceiver temperature becomes excessive, a tone sounds and “HOT” is displayed on the bottom line. Transmit power is then auto matically cut back to approximately 1/3 of normal to limit heat generation. When the temperature is not longer excessive, power output automatically returns to normal. This condition may be caused by transmitting for extended periods or operating in a very warm environment.

If the temperature continues rising to the point where serious transceiver damage could result, “TOO HOT” is displayed, a tone sounds, and the transmitter is disabled. The PTT switch must then be released and the temperature drop t o the exces sive rang e or lowe r to transmit again.

Low Voltage Conditions

If the voltage applied to the transceiver decreases to the point where improper operation could result, “LO VOLT” is displayed on the bottom line, a tone sounds, and the transmitter is disabled. This condition is usually caused by a discharged vehicle battery. To clear this condition, operate the vehicle to charge the battery or transmit with the vehicle running.

2.3.11 SCANNING

detected, the microphone must also be on-hook for scanning to occur. An off-hook condition also dis abl es coded squelch as described in Section 2.4.3

There are two basic scan modes: Standard and Radio Wide. The Standard mode is unique to the type of channel selected (conventional or SMARTNET/ SmartZone), and the Radio Wide mode is the same regardless of the channel type selected. Only one of these scan modes can be enabled at a time. Therefore, if standard scanning is enabled while radio wide scanning is occurring, radio wide scanning is automatic ally disabled and vice versa. More information on these modes follows.

Standard Scanning

Standard scanning monitors only channels that are the same type as that currently selected. Therefore, if a conventional channel is selected, only conventional channels are scanned, and if a SMARTNET channel is selected, only SMARTNET channels are scanned. Standard scanning is turned on and off by the Scan option switch as follows. If this switch is not programmed, standard scanning is not available.

• To turn standard scanni ng on, p ress the Sc an opt ion

switch. Scanning is enabled when the “ indicated in the uppe r l eft cor ner of t h e di sp lay and SCAN x (conventional) or SCAN ON (SMARTNET/SmartZone) is briefly displayed on the lower line of the display. The “x” is the number of the conventional scan list (1, 2, or 3) that is selected. Refer to Section 2.4.11 for more information.

S” icon is

• To turn scanning off, press the Scan option switch

again. The “ “SCAN OFF” is briefly displayed.

S” icon is then no longer indic ated and

Introduction

Scanning cycles through a list of channels, called a “scan list”, checking each for messages. When a message is detected that your transceiver is programmed to receive, scanning stops and the message is received. Shortly after the message is complete, scanning resumes (unless it has been disabled). If the microphone off-hook condition is

• If the zone or channel is changed while scanning is

selected, scanning continues on the same or a different scan list (see scan list information which follows).

Radio Wide Scanning

Radio wide scanning mon itors the ch anne ls in the

preprogrammed radio wide scan list (see information

Revised January 2001

2-5

Part No. 001-9800-501

Page 13

OPERATION

which follows). This list may contain up to 16 channels of any type (conventional or SMARTNET/SmartZone) assigned to any zone. Radio wide scanning is turned on and off by the Radio Wide Scan option switch as follows. If this switch is not programmed, radio wide scanning is not available.

• To turn radio wide scanning on, press the Radio

Wide Scan option switch. The icon is then displayed continuousl y and “RWS ON” is displa yed briefly on the lower line of the display.

• To turn radio wide scanning off, press the Radio

Wide Scan op tion switch aga in. The icon is then no longer indicated and “RWS OFF” is displayed briefly.

• If the zone or channel is changed while radio wide

scanning, scanning continues normally.

Scan Resume Delay

When a message is received or transmitted while scanning, there is a programmable delay before scanning resumes. The delay after receiving a c all prevents another message from being received before you can make a response, and the delay after transmitting a call ensures that you hear a respon se to your call ins tead of another message occurring on some other channel.

Radio Wide Mode Scan List

With radio wide scanning, there is only one preprogrammed scan list available regardless of the type of channel selected, and it is not user programmable.

Determining Which Channels are in Scan List

With st andard co nventional scan ning, the selected channel is in the current scan list if the box icon (around “ display. Channels in SMARTNET/SmartZone standard scan lists are indicated only when edit ing a scan list. Channels in the radio wide scan list are not indicated.

Nuisance Channel Delete

SMARTNET/SmartZone channels can be temporarily deleted from the scan list. This feature is not available with radio wide scanning. Proceed as follows:

NOTE: The selected channel a nd conventi onal priority channels cannot be deleted from the scan list.

1. While receiving a message on the channel to be

S”) is indicated in the upper lef t corner of the

With standard scanning, both conventional and

deleted, press and hold th e Scan opt ion swi tch unt il the alert tone sounds (about 1 second).

Standard Mode Scan List

NOTE: The selected channel is always scanned.

With conv entional oper ation, up to th ree scan list s can be programmed. The list tha t is scanne d is select ed by the Scan option switch as described on Section

2.4.11. Selecting another conventional channel does not change the current sca n lis t. The scan lists are user programmable if the Scan Edit option switch is programmed (see “Programming a Scan List” which follows).

With SMARTNET/SmartZone operation, each channel can be programmed so that one of up to three different scan lists is automatically selected or scanning is disabled. The scan lists are user programmable if the Scan Edit option switch is programmed ( see “Programming a Scan List” which follows).

Revised January 2001 Part No. 001-9800-501

2. The channel is then deleted and scanning of the remaining channels in the scan list resumes.

3. Deleted channels are added back into the scan list if any of the following occur:

• Scanning is turned of f and then on again using the

Scan switch.

• The selected channel is changed.

• Transcei ver power is turned of f and then on again.

Programming a Scan List

If the Scan Edit option switch is programmed, conventional and SMARTNET/SmartZone standard scan lists can be user programmed as follows:

1. Make sure that both standard and radio wide scan-

ning are off (neither the standard scan “

2-6

S” icon or

Page 14

OPERATION

radio-wide scan icon is displayed). Then press the Scan Edit option switch to select the scan list edit mode.

2. With con ventional channels, if applicable, sel ect the list to be edited (1-3) by rotating and then pressing the Select switch. The selected list is indicated as “SCAN x”, where “x” is the l ist number from 1- 3. If user programming is disabled on a list, “NO LIST” is momentarily displayed and it cannot be edited.

With SMARTNET/SmartZone channels, the scan list for the selected channel is fixed and cannot be changed. Scanning may also be disabled on the channel in which case “NO LIST” is momentarily displayed and scan list editing is not available.

3. Select the channel you want to add or delete by rotating the Select switch. After the last conventional chan nel in the current zone is displayed, the first valid channel in the next zone is dis p l aye d and vice versa. SMARTNET/SmartZone lists are limited to 16 channels. If an attempt is made to add more than 16, “LIST FULL” is displayed and a channel must be deleted before another can be added.

4. If the selected channel is in the scan list (scanned), the box icon (around “

S”) is indicated in the

upper left corner of the display. To change th e status of the displayed channel, press the Select switch.

NOTE: The priority channel cannot be delet ed (see “Priority Channel Sampling” description which follows).

5. To exit this mode and save the changes, press the Scan Edit option switch again.

2.3.12 CONVENTIONAL AND SMAR TNET/

SMARTZONE OPERATION

Conventional Operation

This is a non-trunked operation mode which accesses independent radio channels (there is no automatic access to several channels as with trunked operation). Monitoring before transmitting may not occur automatically in this mode, so you may have to manually monitor the channel before transmitting to make sure that it is not being used by anyone else (see Section 2.4.3). Selecting a conventional channel selects a transmit and receive frequency and other parameters such as Call Guard squelch coding.

SMARTNET/SmartZone Operation

This is a trunked operating mode that uses ID codes to select which mobiles are being called and which calls are received. Monitoring is performed automatically and special messages and tones indicate busy and out-of-range conditions. Enhanced features include roaming (SmartZo ne on ly), t elephon e, priv ate, and emergency calls, Call Alert, and messaging. Operating features unique to SMARTNET/SmartZone channels are described in Section 2.5.

This radio supports only the SMARTNET II trunking protocol. It does not support the SMARTNET I (also referred to as Type I) protocol. When a SMARTNET or SmartZone channel is selected or the radio is powered up on one of those channels, it searches for a control channel and attempts to register on the radio system. Once a control channel is found, the alias (name) of the selected channel is displayed. If a control channel could not be found (because of an out of range condition or the system ID is not co rr ect, for e xample) , “NO SYS” is displayed and the radio continues to search for a control channel.

Introduction

Each selectable channel is programmable for either conventional or SMARTNET (trunked) operation. For example, Zone 1/Channel 1 could be a conventional channel, Zone 1/Channel 2 a SMARTNET/SmartZone channel, and so on. More information on these modes follo ws.

™

/SmartZone®

The control channel transmits and receives system information to and from all radios register ed on the system. Therefore, once a contro l channel i s found, it is continuously monitored for incoming call information and is used to make call requests. The radio automatically chang es t o a tra ffic channel to place and receive calls and then returns to the control channel when the call is complete.

Revised January 2001

2-7

Part No. 001-9800-501

Page 15

OPERATION

2.4 CONVENTIONAL FEATURES

2.4.1 INTRODUCTION

The following information describes features unique to the conventional operating mode (described briefly in Section 2.3.12). Refer to Section 2.3 for information on features common to all operating modes, and to Section 2.5 for information on features unique to the SMARTNET/SmartZone mode.

2.4.2 DISPLAY MODE SELECTION

If the Displayed Information option switch is programmed, the display mode used to indicate conventional channels can be user selected. Pressing this switch cycles between the follo wing modes. The selected mode does not change when power is turned off. If the Displayed Information option switch is not programmed, the Alias mode is always used.

Alias - The preprogrammed alphanumeric tag for

the channel is displayed.

Busy Indicator

- With scanning dis abled, note if the Transmit /Busy indi cator o n the fr ont panel is gr een. If it is not, the chann el is n ot being used a nd the ca ll can be transmitted. If it is on, a carrier is being detected, so the channel may be busy (see next paragraph).

Monitor Mode

- There may be times whe n the bus y indication is display ed eve n though no one is using the channel. Monitoring should then be performed by disabling Call Guard squelch by taking the microphone off-hook (if off-hook detection is enabled), pressing the Normal/Selective switch as described in on Section 2.4.6, or by selecting the monitor mode as described next.

2.4.4 MONITOR MODE

The monitor mode temporarily disables squelch

control features (such as Call Guard

squelch) so that all messages are heard on the selected channel. It also overrides the Busy Channel Lockout feature (see next section) and temporarily disables scanning.

Number - The channel number from 1-16 is

displayed.

Frequency - The receive frequency of the selected

channel is displayed in megahertz.

2.4.3 MONITORING BEFORE TRANSMITTING

With conventional operation, channels are moni-

tored automatically or manually as follows:

Automatic Channel Monitoring

If the selected channel is programmed for the Busy Channel Lockout feature, monitoring is performed automatically. Refer to the description of this feature in Section 2.4.5 for more information.

Manual Channel Monitoring

The automatic monitoring just described may not be programmed or it may occasionally disable the transmitter even if the channel is no t in use. In th is case, the channel must be monitored manually as follows:

To monitor the selected channel, select the

monitor mode by briefly pressing the

MON option

switch (if available). The icon is displayed and the receiver unsquelches when the monitor mode is enabled. To disable the monitor mode and return to normal operation, press the

MON switch a second

time.

When scanning is enabled, pressing and holding

the

MON option switch until a tone sounds (approxi-

mately 1 second) monitors th e scanned cha nnel instead of the selected channel.

2.4.5 BUSY CHANNEL LOCKOUT

The Busy Channel Lockout feature (also called Transmit Disable On Busy) automatically disables the transmitter if the channel is busy when the PTT switch is pressed. When a busy condition is detected by this feature, the transmitter is disabled, “BUSY” is indicated on the lower line of the display, and a tone similar to a standard telephone busy tone sounds until the PTT switch is released. This feature is programmed to operate in one of the following modes on each channel:

Revised January 2001 Part No. 001-9800-501

2-8

Page 16

OPERATION

Off - The transmi tter key s ev en if t he channe l is bus y. Noise - The transmitter is disabled if any signal is

detected on the channel.

Tone - The transmi tter is disab led if the detected

squelch coding is not correct.

If busy override is permitted by programming, it is possible to transmit even when the transmitter is disabled by this feature. S imply rel ease the PTT switch and then quickly press it again.

2.4.6 CALL GUARD SQUELCH

General

Call Guard® squelch (also called CTCSS/DCS signaling) may be programmed on conventional channels. This feature eliminates distracting messages intended for others using the channel by using a subaudible tone or digital code to control the squelch. This tone or code is unique to a user or talk group on that channel. It is transmitted by the mobile placing a call, and if Call Guard squelch is programmed in the mobile receiving the call, it must detect the correct tone or code to receive the call.

Call Guard Squelch Enable/Disable

To disable Call Guard (Selective) squelch so that all messages on the selected or scanned conventional channels are heard, take the microphone off-hook (if off-hook detection is enabled) or press the Normal/ Selective option switch if programmed. Then to reenable Call Guard s quelch, place the microphon e b ack on-hook or press the Normal/Selective switch again.

When Call Guard squelch is disabled by the option switch, “SQ NORM” is flashed on the lower line of the display, and when it is enabled, “SQ SLCT” is flashed. The mode selected by this switch does not change when other channels are selected or power is cycled. Call Guard squelch can also be disabled by th e monitor mode described in Section 2.4.4.

2.4.7 PENALTY TIMER

A penalty timer may be programmed on conventional channels to prevent transmissions for a time after the time-out timer described in Section 2.3.7 disables the transmitter. The penalty timer starts when

the PTT switch is released after the transmitter has been disabled. If the PTT switch is pressed during the penalty time, the time-out indication occurs again. A beep sounds when the penalty timer expires and the transmitter can then be keyed.

2.4.8 CONVERSATION TIMER

A conversation timer can be programmed on conventional channels to limit the total length of a conversation rather than just the length of each transmission as with the time-out timer. This timer is reset when the time between transmissions exceeds the penalty time just described. A warning tone sounds 5 seconds before the conver sation timer expi res. When it expires, the transmitter is disabled and a warning tone sounds. The transmitter remains disabled for the length of the penalty time, and a beep sounds when it can be keyed again.

2.4.9 REPEATER TALK-AROUND

Normally, all transmissions go through a repeater which usually increases range. However, if out of range of the repeater, you cannot talk to anyone else on that channel even though t he mobile you are cal ling may be only a short distance away. To allow communication when this situation occurs, repeater talkaround can be used to allow direct communication with a mobile without going through a repeater.

Repeater talk-around can be selected if the Repeater Talk-Around option switch is programmed. When talk-around is enabled by this switch, the icon is displayed and “RTA ON” is flashed on the lower line of the display. Then when it is disabled by pressing the switch again, that icon is no longer displayed and “RTA OFF” is flashed. Changing channels or turning power off does not change the selected talk-around mode.

2.4.10 P OWER OUTPUT SELECT

If the High/Low Power option switch is programmed and power selection is permitted on the current channel by programming, either high or low transmitter power can be selected. Pressing t h i s swit ch toggles the power setting. The new level is flashed on the lower line of the display when this switch is pressed as “HI POWER” or “LO POWER”. If power

2-9

Revised January 2001

Part No. 001-9800-501

Page 17

OPERATION

selection is not permitted on the current channel, the fixed power level is flashed and no power change occurs. Turning power off or changing channels does not change the power setting selected for a channel.

2.4.11 CONVENTIONAL MODE SCANNING

General

The following information describes scanning features unique to conventional operation. Scan operation common to all modes is described in Section

2.3.11, and scan operation unique to SMARTNET/ SmartZone operation is described in Section 2.5.12.

Selecting a Scan List

With conventional standard scanning, one of up to three scan lists can be selected. Scanning is turned on and off and the scan list selected by repeatedly pressing the Scan switch as follows:

1. Press the Scan option switch once to enable scan-

ning and Scan List 1. The “

S” icon is then indicated

in the upper left cor ner of the display a nd “SCAN 1” is momentarily displayed on the bottom line.

2. Press the Scan option switch again to select Scan

List 2 (if available ), a nd “SCAN 2” is momen tarily displayed. Press it again to select Scan List 3 (if available).

3. Pressing the Scan op tion switch again disab les scan -

ning (the “

S” icon is no longer displayed). If the

Scan option switch is pressed again, the cycle repeats.

Transmitting in Scan Mode

selected scan list. The radio transmits on the priority channel.

Priority/Tx Selected - Priority sampling occurs and the priority channel is the one programmed in the selected scan list. The radio transmits on the selected channel.

Priority on Selected - The priority channel is always the selected channel. The radio transmits on the selected channel.

Talkback - No priority sampling occurs. The radio transmits on the channel of a call while scanning is halted. Then once scanning resumes, it transmits on the selected channel.

2.4.12 PRIORITY CHANNEL SAMPLING

General

The priority channel sampling feature ensures that when standard scanning, messages on the priority channel are not miss ed whil e listen ing to a mess age on some other channel. The transceiver can be programmed so that the priority channel is a fixed channel associated with the current scan list, the currently selected channel, or not used. When the selected channel is a priority channel, “

P” is indicated

in the upper right part of the display.

Priority channel sampling occurs only with Standard conventional scanning. It does not occur with Radio Wide scanning, when listening to any type of SMARTNET/ SmartZon e call, or when tr ansmittin g. A series of “ticks” may be heard when the priority channel is sampled while listening to a message on some other channel.

Each conventional scan list can be programmed for one of the following modes. These modes determine if priority sampling occurs and also the channel on which transmissions occur while scanni ng. Refe r to the next sec t ion for more information.

No Priority - No priority channel sampling occurs when the list is selected. The radio transmits on the selected channel.

Priority/Tx Priority - Priority sampling occurs and the priority channel is the one programmed in the

Revised January 2001 Part No. 001-9800-501

The priority sampling times are programmed by

the following parameters:

Lookback Time A - This time determines how often the priority channel is checked for activity. Times of

0.25-4.00 seconds in 0.25-second st eps can be programmed.

Lookback Time B - This time determines how often the priority channel is checked once an incorrect Call Guard (CTCSS/DCS) code is detected. Since it takes much longe r to detect an incorrect Call Guard signal

2-10

Page 18

OPERATION

than a carrier, this time should be relatively long to prevent the interruptions from making a message difficult to understand. Times of 0.5-8.0 seconds can be programmed in 0.5-second steps.

Changing The Priority Channel

If a specific priority channel is associated with the current scan list, it can be changed if the Priority option switch is programmed. Proceed as follows:

1. Make sure all scanning is off (neither the standard

scan “

S” icon or radio-wide scan icon is

displayed).

2. Select the channel that you want to be the priority

channel using the Select switch in the normal manner. If the channel is in a different zone, also select the appropriate zone.

3. Press the Priority option switch and the “

P” icon is

displayed to indicate that the selected channe l is now the priority channel.

2.4.13 STANDARD CONVENTIONAL CALLS

Standard conventional calls are calls to or from other mobile units on the se le cte d channel. The proper coded Call Guard signaling (see Section 2.4.6) may need to be transmitted for them to receive your call and also for you to receive their calls. Proceed as follows to place and receive these calls:

Placing a Standard Conventional Call

1. Turn power on and set the volume as described in

Section 2.3.2. Select the channel programmed for the mobile you want to call (see Section 2.3.5).

2. Monitor the channel a utomatically or manually as

described in Section 2.4.3.

3. Press the PTT switch and the call proceeds as

follows:

• Otherwise, busy and out-of-range conditions are

not indicated and speaking can begin after monitoring the channel.

4. Press (and hold) the PTT switch to talk and release it to listen.

Receiving a Standard Conventional Call

1. Select or scan the channel programmed for the call you want to receive (refer to Sections 2.3.11 and

2.4.11 for more scanning information).

2. When the call is received, press the PTT switch to talk and release it to listen. If scanning, you may have to respond before scanning resumes to ensure that the response occurs on the channel of the call.

2.4.14 DTMF/ANI SIGNALING

DTMF (Dual Tone Multi-Frequency) tones can be generated manually or automatically for ANI (Automatic Number Identification) and other purposes. The following options may be enabled by programming for each conventional channel:

DTMF Keypad - Pressing 0-9, *, or # on the keypad of an optional DTMF microphone transmits the corresponding tone (the PTT switch must also be pressed if the transmitter does not automatically turn on when a key is pressed).

Pre-Tx ANI - A preprogrammed ANI sequence is automatically sent when you press the PTT switch.

Post-TX ANI - A preprogrammed ANI sequence is automatically sent each time you release the PTT switch.

Disabled - ANI signali ng is disabled.

2.5 SMARTNET/SMARTZONE FEATURES

2.5.1 INTRODUCTION

• If the Busy Channel Lockout feature is

programmed on the channel, the transmitter is automatically disabled if the channel is busy (see description in Section 2.4.5).

The following information describes the features unique to the SMARTNET/SmartZone operating mode described briefly in Section 2.3.12. Features common to all operating modes are described in

Revised January 2001

2-11

Part No. 001-9800-501

Page 19

OPERATION

Section 2.3, and features unique to the conventional mode are described in Section 2.4.

2.5.2 VIEWING UNIT ID

Each radio in a SMARTNET system is identified with a system ID and Unit ID. To display the Unit ID, make sure t hat a SMARTNET/SmartZone channel is selected and then turn power off and then on again. The software version number, current zone, and sixdigit Unit ID are then displayed in sequence. The Unit ID is displayed as IDxxxxxx.

2.5.3 STANDARD GROUP CALLS

Standard calls are between you and another mobile, group of mobiles, or a control station (a radio at a fixed locati on). Most call s you make wil l prob ably be this type.

Placing a Standard Group Call

1. Turn power on and set the volume as described in

Section 2.3.2. Select the channel programmed for the talk group you want to call (see Section 2.3.5). A regular or announcement talk group can be selected.

2. Press the PTT switch and when the alert tone

sounds, begin talking. Other indications that may occur are as follows:

• If the busy tone so unds and “BUSY” i s displayed,

the system is busy. Release the PTT switch and

wait for the call back tone to sound. Then press the

PTT switch within 3 seconds and begin talking.

• If a continuous tone sounds while pressing the

PTT switch, an out-of-range condition may exist.

Drive closer or away from shielding objects and

try again.

• If your unit ID is invalid , the call is bei ng made to

an invalid group ID, or group calls are n ot allowed,

“INVALID ID” is displayed and an alert tone

sounds.

display either th e talk group o f the inco ming cal l or the ID of the radio making the incoming call. If the ID is in the Trunking Call List, the alias of that mobile is displayed instead of th e ID. If neither of these features are programmed, the alias of the selected talk group continues to be displayed when a call is received.

2.5.4 ENHANCED PRIVATE CONVERSATION CALLS

General

Private calls a llow yo u to pl ace a ca ll to a spe cific

mobile unit. Either the Enhanced Private Conversa-

™

tion

or Private Conversation II™ modes may be programmed depending on the capabil ities of the radio system. Operation in the Enhanced Private Conversation mode is described in the following information, and operation in the Private Conversation II mode is described in Section 2.5.5.

The Private Call option switch is required to place these calls, and either that switch or the Call Response option switch is required to receive them. Proceed as follows.

Placing an Enhanced Private Conversation Call

This call is initiated by selecting the unit ID from a call list (list ent ry) or by direct ly enteri ng it us ing the microphone keypad (direct entry). Proceed as follows:

List Entry Method

1. With a SMARTNET/SmartZone channel selected,

momentarily press the Private Call option switch. The private call mode is then i ndicated by “ upper part of the display. Then if the last ID called matches an ID in your call list, it is display ed on the lower line and the name is displayed on the upper line. Otherwise, only the la st ID cal led is di spl aye d.

2. Scroll through the private call list by rotating the

Select switch until the desired ID is displayed. To cancel the c all, press the Private Call switch.

C” in the

Receiving a Standard Call

When a SMARTNET/SmartZone group call is

received, the transceiver can be programmed to

Revised January 2001 Part No. 001-9800-501

3. Press the P TT swi tch to init iate the cal l. The displa y

then indicates the alias of the destination radio. Proceed to the bulleted list following the next method for conditions that may occur next.

2-12

Page 20

OPERATION

Direct Entry Method (With DTMF Microphone Only)

1. With a SMARTNET/SmartZone channel selected, press and hold the Privat e Call opti on switch unt il a tone sounds (approximately 1 second). The last ID called is displ ayed on the upper l ine, and the p rivate call mode is i ndicated by “ display.

2. Using the 0-9, #, and * keys, ent er the 6-di gi t I D of the mobile unit you are calling. To erase the last digit entered, rotate the Select switch counterclockwise, and press the Private Ca ll switc h to cancel the call.

3. Press the PTT switch to initiate the call. If the entered ID is invalid, “INVALID” is momentarily displayed and the call is not initiated. If the entered ID is valid, the alias of the ID is disp layed on the lower line if it matches an ID in your call list. Otherwise, only the ID you entered continues to be displayed. Any of the following conditions may then occur:

C” in the upper part of the

• If the radio you are calli ng is on th e air, telephone

type “ringing” i s h ear d f o r 20 s econds or until the called party answers.

• If the called party answers and the call is

successful, the person’s voice is heard and the call is carried on the same as a group call. To end the call at any time, press the Private Call switch.

• If the called party does not answer within 20

seconds, “NO ANSWR” is displayed and a contin uous tone sounds. End the call by pressing the Private Call switch.

• If the called radio is not in service, no ringing is

heard, “NO ACK” is displayed, and a continuous tone sounds. End the call by pressing the Private Call switch.

• If neither your radio nor the radio being called is

authorized to make unit-to-unit calls, “NO ACK” is displayed and a continuous ton e sounds. End the call by pres sing the Private Call switch.

displayed. When the system is no lo nger busy, the called party automaticall y resp onds .

• If an out-of-range condition exists or the radio

system is not in service, “NO SYS” is displayed and a continuous tone sounds. End the call by pressing the Private Call switch.

Receiving an Enhanced Private Conversation Call

This call is automatically received if a SMARTNET/SmartZone channel is selected. Proceed as follows:

1. When this call is receiv ed, a recurri ng unit call tone

(three beeps) sounds for up to 20 seconds and “CALL RCV” is displayed on the lower line.

2. To answer the call, press the Private Call option

switch and then the PTT switch and begin talking. The private call mode is indicated by “ upper part of the display, and the alias of the incoming call is displayed if the ID is in your call list. Otherwise, the unit ID is displayed. NOTE: If

the Private Call opti on swi tc h i s not pressed before the PTT switch, a group call is transmitted on the selected group.

C” in the

• T o end th e call when the con versati on is comple te

or at any other time, press the Private Call switch.

• If private calls are not permitted (Private Call

switch not programmed ), pr ess t he Call Response

option switch, if available, to answer the call.

• If the call is not answered within 20 seconds, it is

automatically terminated.

• If the radio system is busy, four low tones sound

and “BUSY” is displayed. When th e sys te m is no

longer busy, the call back tone (four beeps) is

heard and your radio automa tically start s transmit-

ting. Press the PTT switch to continue the call.

• If the called party answe rs but the radio system is

busy, four low tones sound and “BUSY” is

• To ignore an incoming call, wait 20 seconds until

the recurring unit call tone stops sounding.

Revised January 2001

2-13

Part No. 001-9800-501

Page 21

OPERATION

2.5.5 PRIVATE CONVERSATION II CALLS

General

Private calls allow y ou to p lace a ca ll t o a spe cifi c mobile unit. Either the Enhanced Pr ivate Conversation™ or Private Conversation II™ modes may be programmed depending on the capabi lities of the radio system. Operation in the Enhanced Private Conversation mode is described in Section 2.5.4, and operation in the Private Conve rs at ion II mode is described in the following information.

The Private Call option switch is required to place these calls, and either the Private Call or Call Response option switch is requir ed to receive them. Proceed as follows.

Placing a Private Conversation II Call

This call is initiated by selecting the unit ID from a call list (list entry) or by directly entering it using the microphone keypad (direct entry). Proceed as follows:

List Entry Method

1. With a SMARTNET/SmartZone channel selected,

momentarily press the Private Call option switch. The private call mode is indicated by “ upper part of the displ ay , a nd the alias (n ame) of the last ID called is displ ayed if it matches an ID in your call list. Otherwise, the last ID called is displayed.

2. Scroll through the private call list by rotating the

Select switch un til the desi red ID is dis played. Press the Private Call switch again to cancel the call.

3. Press the P TT swi tch to init iate the ca ll. The dis play

then indicates the alias of the destination radio. Wait approximately 1 second and then begin talking. Proceed to the bulleted list following the next method for conditions that may occur next.

Direct Entry Method (With DTMF Microphone Only)

1. With a SMARTNET/SmartZone channel selected,

press and hold the Privat e Call opti on switch unt il a tone sounds (approximately 1 second). The last ID called is displaye d on the upper l ine, and the p rivate call mode is i ndicated by “ display.

C” in the upper part of the

C” in the

3. Press the PTT switch to initiate the call. If the entered ID is invalid, “INVALID” is momentarily displayed and the call is not initiated. If the entered ID is valid, the alias of the ID is displayed on the lower line if it matches an ID in your call list. Otherwise, only the ID you entered continues to be displayed. Wait approximately 1 second and begin talking. Any of the following conditions may then occur:

• If the called party answers and the call is

successful, the pers on’ s voice is heard and the cal l is carried on the same as a group call. To end the call at any time, press the Private Call switch.

• If the radio system is busy, four low tones sound

and “BUSY” is displayed. When th e sys te m is no longer busy, the call back tone (four beeps) is heard and a channel is automatically acquired. Press the PTT switch to continue the call.

Receiving a Private Conversation II Call

Private calls are automatically received if a SMARTNET/SmartZone channel is selected. Proceed as follows:

1. When a call is receive d, an alert tone sou nds and the

caller’s v oic e i s heard. While voice is heard, “ indicated in the upper part of th e display and “CALL RCV” is displayed and the l ower line of t he display.

2. To answer the call, press the Private Call option

the Private Call opti on swi tc h i s not pressed before the PTT switch, a group call is transmitted on the selected group.

C” in the

C” is

• T o end th e call when the con versat ion is comple te

or at any other time, press the Private Call option

Revised January 2001 Part No. 001-9800-501

2-14

Page 22

OPERATION

switch again. If the call is not answered wit hin 20 seconds, it is automatically terminated.

• If private calls are not permitted (Private Call

switch not programmed), pr ess the Call Respo nse option switch, if available, to answer the call.

2.5.6 TELEPHONE CALLS

General

Telephone calls allow you to place and receive calls over the public telephone system using your transceiver. If your transceiver is programmed for telephone calls (Phone option switch programmed), they are placed and received as follows:

Placing a Telephone Call

Telephone calls can be placed by selecting the number from a prepro grammed phone number li st (l is t entry) or by directly entering it using the microphone keypad (direct entry). Proceed as follows:

List Entry Method

Direct Entry Method (With DTMF Microphone Only)

1. With a SMARTNET/SmartZone channel selected, press and hold the Phone option switch until a tone sounds (approximately 1 second). The last phone number called is displayed, and the phone mode is indicated by the icon.

2. Enter the number using the enter a pause (indi cated by “ P”), press and then

#. The number scrolls to the left in the display so

that the seven right-most digits are always displayed. Numbers up to 16 digits (including pauses) can be entered. To erase the last digit entered, rotate the Select switch counterclockwise, and press the Phone switch to cancel the call.

3. Press the P TT swi tch to init iate the cal l. The dis play indicates “DIALING” while the connection to the phone system is occurring. Once connected, the normal dial ton e is heard a nd the alias of the number being called is again dis played. The radio then auto matically dials the telephone number and the normal ringing or busy tone is heard. Any of the following conditions may then occur.

0-9, , and # keys. T o

1. With a SMARTNET/SmartZone channel selected, momentarily press the Phone option switch. The phone mode is indicated by the icon, and the display indicates the alias of the last called telephone number if it is in your phone number list. Otherwise, the last called telephone number is displayed.

2. Scroll through the list of telephone numbers by rotating the Sele ct switch until the desired nu mber is found. Press the Phon e option switch again to ca ncel the call.

3. Press the P TT swi tch to init iate the ca ll. The dis play indicates “DIALING” while the connection to the phone system is occurring. Once connected, the normal dial ton e is heard a nd the alias of the number being called is again dis played . The radio then a utomatically dials the telep hone number and the normal ringing or busy tone i s heard. Proceed to the bulleted list following the next method for conditions that may occur next.

• After the called party answers, press the PTT

switch to talk and release it to listen. You cannot talk and listen at the same time because the radio cannot transmit and rece ive at the same time. Each time the P TT swi tch is re leased, a t one is heard by the other party that indi cates whe n a respons e can be made. To end the call when the convers ation i s complete or at any other time, press the Phone option switch again.

• If equipped with an opt ional DTMF microphone, a

number can be dialed during a call.

• If an out-of-range condition exists or the radio

system is not in serv ice, “HANG UP” is di splayed and a continuous tone sounds. End the call by pressing the Phone option switch.

• If you are not authori zed to make t el epho ne calls,

“REJECT” is displayed and a continuous tone sounds. End the call by pres sing t he Phone op tion switch.

2-15

Revised January 2001

Part No. 001-9800-501

Page 23

OPERATION

• If the radio system is busy, “BUSY” is displayed

and a busy tone sounds. The call automatically proceeds when the radio system becomes available. If the call is ended before it proceeds, your position in queue is lost.

Answering a Telephone Call

T elephone calls are automatically received if a SMARTNET/SmartZone channel is selected. Proceed as follows:

1. When a telephone c all is re ceived, “ringi ng” similar

to a standard telephone is heard, and the display indicates “PHONE” on the bottom line.

2. To answer the call, press the Phone option switch

and the phone mode is indicated by the icon. Press the PTT switch to talk and release it to listen.

3. T o end the call when the conversati on is complete or

at any other time, press the Phone option switch again.

2.5.7 CALL ALERT

of the selected channel is then displayed continuously.

• If the radio you are paging is no t in servi ce, a tone

sounds and “NO ACK” is displaye d. Press the Call Alert switch again to cancel the page.

Answering a Page

1. When a page is re ceived, “ PAGE RCV” is indicated on the bottom line and a recurring received page tone (six beeps) sounds.

2. Answering a page is the same as placing a private call. Therefore, pre ss the Pr ivate Call option switc h and follow the i nstruct ions for placing a priva te ca ll in Section 2.5.4 or 2.5.5, whichever is applicable.

2.5.8 MESSAGING

The messaging feature allows pr eprogrammed messages to be sent to your dispatcher. Up to 16 messages can be preprogrammed, and they are identified by alias (name). If a Message option switch is programmed, messages are sent as follows:

The Call Alert™ feature allows pages to be sent

and received as follows:

Sending a Page

1. With a SMARTNET/SmartZone channel selected, momentarily press the Call Alert option s witch. The tag (alias) of the last ID called is disp layed if it matches an ID in your call list. Otherwise, the last ID called is displayed.

2. To select the desired ID, rotate the Select switch to scroll through the ID list. Press the Call Alert option switch again to cancel the call.

3. Press the PTT switch to send the page. The display then indicates the alias of the radio being paged. Conditions that may then occur are as follows:

• If the radio you are paging is on the air and

received your page, a signaling success tone (six beeps) sounds and the display momentarily indicates “ACK RCVD” on the bo ttom l ine. Th e ali as

1. Momentarily press the Mes sag e option switch. The alias of the l ast message sent is displayed.

2. Scroll through the message list by rotating the Select switch until you find the desi red message. Pr ess the Message option switch a gai n to canc el the mes sage.

3. Press the P TT s witch to send the message. Whe n the message is received and acknowledged by the dispatcher, a signaling success tone (six beeps) sounds and the display returns to the normal channe l indication. If there is no acknowledgment after 6 seconds, a tone sounds and “NO ACK” is displayed . Press the Message option switch again to return to normal operation.

2.5.9 SENDING STATUS CONDITIONS

The status feature allows you to send your current status to a dispatcher. Up to eight status conditions can be preprogrammed, and they are identified by an alias (name). If the Status option switch is programmed, status conditions are sent as follows:

Revised January 2001 Part No. 001-9800-501

2-16

Page 24

OPERATION

1. Momentarily press the Status option swit ch, and the alias of the last status sent is displayed.

2. To change the displayed status, scroll through the status list by rotating the Select sw itch. Press the Status option switch again to cancel this function.

3. Press the PTT switch to send the status. When the message is received and acknowledged by the dispatcher, a signaling success tone (six beeps) sounds and the displa y returns to the normal channe l indication. If there is no acknowledgment after 6 seconds, a tone sounds and “NO ACK” is displaye d. Press the Status option switch again to return to normal operation.

2.5.10 EMERGENCY ALARM AND CALL

Introduction

Emergency Alarms and Emergency Calls are separate functions that can be individually enabled or disabled on each SMARTNET/SmartZone system. The Emergency option switch is also required for these functions, and it is always the button to the left of the display when it is used. Emergency Alarms and Calls are transmitted on the emergency talk group programmed on the selected system.

Emergency Alarms

An emergency alarm is a special data transmission that alerts a dispatcher of an emergency situation. Proceed as follows to activate an emergency alarm:

1. Select a SMARTNET/SmartZone channel that has

this feature enabled and then press the Emergency option switch. The radio then begins automatically transmitting an emer gen cy al arm dat a messa ge and “EMERGNCY” is indicated in the display for 3 seconds.

number of attempts have been made. To exit this mode, power must be turned off and then on again.

Emergency Calls

An emergency call urgently requests access to a

voice channel. To place this call, proceed as follows:

1. Select a SMARTNET/SmartZone channel that has this feature enabl ed and press the Emer gency option switch. The emergency mode is indicated when “EMERGNCY” is indicated in the display for 3 seconds.

2. To place the emergency call, manually press the PTT switch and begin speaking as with a standard call. All group calls which follow are then emergency calls (private, telephone, and call alert calls are not allowed). If the channel is changed, the call is made on the emergency talk group programmed for the new channel.

3. T o exit this mode, power must be t urned off and then on again.

2.5.11 FAILSOFT OPERATION

If a failure occurs in the SMARTNET/SmartZone system so that it cannot be used, the transceiver automatically enters the failsoft mode. When this mode is selected, “FAILSOFT” is indicated on the lower line of the display.

When in the failsoft mode, operati on is in the conventional mode on a preprogrammed failsoft channel. If a transmi ssion is at tempte d before a fa ilsoft channel is located, a continuous tone sounds until the P TT sw it ch is rel eas ed. Wh en the radi o sys te m re tur ns to normal op eration, this condition is automatic ally detected and normal operation resumes.

2. When the emergency alarm is acknowledged, the emergency acknowledge tone (two beeps) sounds. Silent operation may al so be pr ogr ammed i n whi ch case no tone sounds and there is no indication that an acknowledgment occurred.

3. The radio continues to transmit this messa ge until an acknowledgment is received or the programmed

2.5.12 SMARTNET/SMARTZONE SCANNING

Scanning on a SMARTNET/Smartzone channel is similar to the standard and radio wide scanning described starting in Section 2.3.11. Each channel can be programmed with a different scan list that includes up to 16 channels, one of which can be a priority channel. Up to three lists can be programmed, and

Revised January 2001

2-17

Part No. 001-9800-501

Page 25

OPERATION

they are user programmable if the Scan Edit option switch is programmed (see “Pro graming a Scan List” in Section 2.3.11).

Scanning is enabled/disabled by the Scan option switch. In addition, channels can be programmed so that scanni ng automatically starts whenever the channel is selected. Scanning is temporarily disabled and “

S” turns off if a channel is selected that has scan-

ning disabled. Then when a channel is selected again that permits scanning, it is automatically re-enabled.

When responding to messages in the scan mode, programming determines if the response always occurs on the talk group of the call or the selected talk group (if they are different). Transmissions occurring at other times always occur on the selected talk group.

In addition to calls on channels in the scan list, pages, private calls, and telephone calls are received while scanning. Messages on the priority channel are received while listening to lower priority messages. However, private and telephone calls are not interrupted by calls on the priority channel.

2.5.13 DYNAMIC REGROUPING

The dynamic regrouping feature allows a dispatcher to switch users to a dynamically defined channel to receive an important message. Dynamic regrouping operates as follows:

1. When this command is received, the alterna ti ng

dynamic regrouping tone sounds, the transceiver automatically changes to the regrouping channel, and the display indic ates “REGROUP” on the lower line. All transmitting and receiving then occurs on this channel .

2. T o reset all talk and annou ncement groups to normal

so that only the designated regr ouping channel is on the dynamic group, manually select the designated regrouping channel if you kno w it. If this channel is not selected or there is no designated regrouping channel, all tran smissions occu r on the dyna mically assigned group regardless of which channel is selected, and the regrouping tone sounds each time the PTT switch is pressed.

3. When regrouping is canceled by the dispatcher, transceiver operation returns to normal.

2.5.14 SMARTZONE FEATURES

Introduction

As described in Section 2.3.12, the SmartZone® mode provides wide area coverage by allowing roaming between SMARTNET and conventional sites. SmartZone operation is th e same as SM ARTNET with the following additional features:

Determining Current Site

To determine the current radio site, momentarily press the Site Search option sw itch (if progra mmed). If currently register ed on a site, “ SITE x” is di splay ed on the top line, where “x” is the site number. If the site is locked (see following), “LOCK x” is displayed instead. The RSSI (Receive Signal Strength Indicator) value of the current site as “RSSI x” is displayed on the bottom line as “RSSI x”. To exit, press the Site Search switch again.

Searching For a New Site

Press the Site Search option switch as described above. Then to scroll through the other programmed sites, rotate the Select switch while “SITE x” or “RSSI x” is displayed. To select the displayed site, press the Site Search option switch. To exit this mode and return to normal op eration, press the Site Se arch switch again. If site loc k is on when site s earch i s en tered (see following), the radio will be locked on the new site when this function is exited.

Locking/Unlocking a Site

It is sometimes desirable to stay on the current site regardless of signal level. To lock the radio on the current site so that it doe s not sear ch f or another, press the Site Lock option switch (if programmed). The display then momentarily indicates “LOCK x” to indicate that the current site is locked (“x” is the current site number). To unlock the site, press the L ock switch again and “UNLOCK” is momentarily displayed.

Revised January 2001 Part No. 001-9800-501

2-18

Page 26

OPERATION

When locked on a site, i t is st ill po ssibl e to se arch for a different site using the site search function described in the preceding section. When a new site is found, the radio is then locked on that site.

2.6 SUPERVISORY TONES

Single Beep (Alert Tone)

• Power was turned on and a successful power-up

sequence occurred (Section 2.3.2).

• The time-out timer is about to expi re or the penalty

timer has expired (Sections 2.3.7 and 2.4.7).

• The conversation timer is about to expire (Section

2.4.8).

• The system receiv ed your page but the p aged mobile

is not on the air (Section 2.5.7).

• Telephone interconnect is not operational (Section

2.5.6).

Continuous Tone (Invalid or No Acknowledge Condition)

• A transmission is being attempted on an unpro-

grammed channel or a conventional channel programmed as receive-only.

• The transmitter is disabled by the busy channel

lockout feature (Section 2.4.5).

• The transmitter has been disabled by the time-out

timer feature (Section 2.3.7).

• The transmitter has been disabled by the conversa-

tion timer (Section 2.4.8).

• An out-of-range condition exists (SMARTNET/

SmartZone only).

• A transmission is be ing attempted before the penalt y

timer has expired (Section 2.4.7).

• Dynamic regrouping has been exited but the

dynamic regrouping channel is still selected (Section 2.5.13).

• The paged mobile did not acknowledge the page

(Section 2.5.7).

• The message that was sent has not been acknowl-

edged (Section 2.5.8).

• The status condition that was sent has not been

acknowledged (Section 2.5.9) .

Single Short Medium-Pitch Tone

• A valid key has been pressed.

Single Short Low-Pitch Tone

• An invalid key has been pressed.

Six Beeps (Recurring)

• The page was received (Section 2.5.7).

Three Beeps (Recurring)

• A unit-to-unit call was received (Section 2.5.4).

Six Beeps

• The paged radio received the page and acknowl-

edged it (Section 2.5.7).

• The message that was sent has been received and

acknowledged (Section 2.5.8).

• The status condit ion that was sent has been received

and acknowledged (Section 2.5.9).

Two Beeps

• The emergency alar m condi tion was a ckno wledged

(Section 2.5.10).

Gurgle-Like Tone

• Dynamic regrouping has occurred (Section 2.5.13).

• Dynamic regrouping has occurred but the

regrouping channel is not selected (Section 2.5.13).

Four Low Tones (Busy Signal)

• The radio system is busy or a busy condition exists

when making a telephone call.

Four Alternating High and Low Tones

• A channel is available after a busy condi ti on

occurred (SMARTNET/SmartZone only).

2-19

Revised January 2001

Part No. 001-9800-501

Page 27

SECTION 3 PROGRAMMING

PROGRAMMING

3.1 GENERAL

3.1.1 PROGRAMMING SETUP

Remote Programming Interface (RPI)

Part No. 023-9800-000

Figure 3-1 Programming Setup

• A hard disk drive with at least 5 MB of free space

• A CD-ROM drive

• An available serial port

Programming Cable

Part No. 597-2002-200

Battery

Ign Sense

Antenna

The following items are required to program the transceiver and control unit. The part numbers of this equipment are shown in Table 1-1 in Section 1. The programming set-up is shown above.

• IBM

PC or compatible personal computer

• Remote Prog. Interface (RPI) P.N. 023-9800-000

• Cables from the RPI to the computer and

transceiver

• E.F. Johnson PCTrunk programming software.

3.1.2 COMPUTER DESCRIPTION

The computer used to run this program should meet the following minimum requirements:

• Windows

2000 is supported only by PCTrunk Version 5.10.0 or later)

• Intel

3.1, 95/98, or NT 3.51 (Windows NT/

486 processor or equivalent

• At least 4 MB of RAM

NOTE: With the descriptions which follow, it is assumed that you have a basic understanding of how to use your Windows-based operating system. If you are not familiar with some of the Windows functions described, refer to your Help Screens and manuals included with your Windows software.

3.1.3 PCTRUNK SOFTWARE INSTALLATION

The PCTrunk software is supplied on a CD-

ROM. Install this software as follows:

1. Make sure that t here a re no other Windows applications open during this installation procedure. Also, make sure that the computer meets the minimum requirements listed in the preceding section.

2. Insert PCTrunk CD-ROM in the CD drive of your computer.

3-1

Revised January 2001

Part No. 001-7780-501

Page 28

PROGRAMMING

3. Windows 3.1 - In the Program Manager, double

click the SETUP.EXE file on the CD-ROM or click that file name and select File > Run.

Windows 95/98/NT - In the bottom left corner of the screen, select Start > Run and then click the Browse button in the window that is displayed. Then in the “Look In:” pull-down menu, select the CD-ROM drive and the file “Setupxx.x.exe”. Click the open button and then from the Run window, click OK and the installation process begins. (The “xx.x” in the filename is the version of PCTrunk being loaded.)

4. Follow the instructions displayed by the setup program. The default directory for the program is \Program Files\PCTrunk. If you wish to use some other directory , cl ick Browse and select it or type the name.

3.1.4 CONNECTING RPI TO COMPUTER AND

TRANSCEIVER

RPI Information

The RPI provides the required interface between the computer and transceiver. It converts the RS-232 logic levels from the computer to the TTL logic levels required by the transceiver microprocessor and vice versa.

indicator is amber. The standard mode should be selected for all but Flash programming.

With some remote mount transceivers (not 9800 series), this switch is used to turn transceiver power on and off. A separate 9-16 VDC, 200 mA power supply (such as P.N. 563-0001-005) must then be plu gged int o the RPI power jack to provide power to the RPI.

Cable Information

The cables from the RPI to the computer and transceiver are not included with the RPI. The -9800RPI has a female DB9 connector for the computer connection. Since most computer serial ports have a male DB9 or DB25 connector, a male DB9 to female DB9 or DB25 is usually required. This is a standard cable available at most computer supply stores. A suitable cable is also listed in Table 1-1.

The cable from the RPI to the transceiver has modular telephone-style connectors on each end. It plugs into the microphone jack on the front panel of the transceiver. The cable for this application is also listed in Table 1-1.

3.1.5 STARTING AND EXITING

To Start PCTrunk From Windows 3.1

A new RPI (Part No. 023-9800-000) has been designed for this transceiver. This RPI is backward compatible, so it can also be used to program other E.F . Johnson tr ansceiver s which requ ire an RPI (e xcept the 5300 series). This new RPI is required to Flash program the transceiver to update the logic board operating software, and it has a phone jack that is required for injecting the transmit audio signal during alignment. To perform the standard personality programming described in most of this section, earlier RPI’s such as Part No. 023-5810-000 or 023-9750-000 can also be used.

When programming both front and remo te models of this transceiver, the switch on the front panel of the RPI selects either the standard or Flash programming mode. The standard mode is selected when it is away from the LED and the indicator is green, and the Flash mode is selec ted when it is toward the LED and the

Revised January 2001 Part No. 001-7780-501

In the Program Manager, open the PCT runk group

window. Then double-click the PCTrunk icon.

To Start PCTrunk From Windows 95/98

Click the Start button and select the PCTrunk

group. Then double-click the PCTrunk icon.

To Exit PCTrunk:

Select File > Exit or press ALT + F4.

3.1.6 PROGRAMMING FILE TYPES

Programming data is stored in a disk file that can be saved, read, copied, and deleted (see Section 3.3.1). The file that is stored for each programming session has the .DAT extension.

3-2

Page 29

Data File Name

Radio Wide Screens

System Screens

Conv System

SMARTNET System

Channel Screen

PROGRAMMING

Figure 3-2 Main Screen (Later PCTrunk Versions)

3.1.7 HELP FILES

T o displ ay help inf ormation on t he curren t screen,

click Help in the menu bar or press F1.

3.1.8 SCREEN GROUPS

General

The following screen groups are displayed:

Radio-Wide - These screens program parameters that are the same for all systems and channels. Separate screens are displayed for General, Conventional, SMARTNET/SmartZone, and Mobile Options parameters. Refer to Sectio n 3.4 for mor e information on these screens.

System - These screens program the parameters th at are unique to the displayed Conventional, SMARTNET, or SmartZone system. The system to be edited is selected as described in Section 3.1.11.

3.1.9 DISPLAYING SCREENS

The latest release of PCTrunk uses a different method of displaying screens. Proceed as follows to select which screens are displayed with the different versions:

Revised PC Trunk (Version 5.10.0 or Later)

Revised versions of PCTrunk use a pane on the left side of the screen (see Figure 3-2) to display the screen structure similar to the directory structure of a hard drive. Clic k t he “+ ” to expand the branch and “–” to collapse it. Then to display a screen, simply click its name. The current screen may have to be closed in order to select another one.

Early PCTrunk (Versions Prior to 5.10.0)

With early versions of PCTrunk, the screens are displayed in cascade style or they can be minimized like any Windows screen. To cascade the active screens, select Window > Cascade from the menu bar.

Channel - This screen programs unique channel parameters and assigns channels to each zone. The specific parameters indicated in this screen are determined by the type of system selected in the “Type” box (Conventional, SMARTNET, SmartZone).

To pop a screen to the front, click the applicable button which follows. For example, if the Channel screen is displayed and you want to quickly pop the Radio-Wide screen to the front, click the Radio-Wide button. These buttons can be displayed or hidden by

Revised January 2001

3-3

Part No. 001-7780-501

Page 30

PROGRAMMING

clicking Window > Toolbar. A window can also be displayed by selecting it in the Window Menu.

Screen Pop-Up Buttons

(Early PC Trunk Versions)

3.1.10 FILE SIZE INDICATOR

The maximum number of channels that can be programmed may be limited by the available memory space in the radio (see Section 1.5.3). A running indication of the amount of memory used by the current data (if it was downloa ded to t he radi o) is displ ayed by a bar graph as shown in Figure 3-2 and the preceding illustration. When the bar reaches the right end, available memory is f ull and some channels may ne ed to be deleted to program more information.

3.1.11 CREATING AND DISPLAYING

SYSTEMS

To create a new SMARTNET or SmartZone system, select Systems > Add Systems and then the desired system type from the menu bar (see Section

3.3.5). This menu is also used to delete a system.

NOTE: Only one conventional system can be set up, and it is automatically created when a new file is created as described in Section 3.3.1. Therefore, there is no option to add a conventional system.

Only one system can be displayed at a time, so select the system to be edited as described in the preceding section. Systems are indicated by number and type. Channels and talk grou ps for al l progra mmed systems are set up in the Channels screen. Therefore, any channel can be selected when programming channel information.

3.2 PROGRAMMING PROCEDURE

The following is a general procedure you can use to program a transceiver.

3.2.1 PRELIMINARY

1. Select a programming file as follows:

Create a New File - To start with a new file containing default parameters, select File > New and then the frequency band of the radio (VHF/ UHF/800 MHz).

Open An Existing File - To open an existing file stored on disk, select File > Open and then the file to be opened.

Upload a File From a Rad io - To transfer a file from a radio to the computer to edit or use as a basis to program anot her rad io, connect the ra dio to the computer as described in Section 3.1.4. Then turn the radio on and select Upload from the menu bar.

2. Before or after creating the programming file, be sure the correct t ype (98xx mobile) is select ed by the Radio Type menu (see Section 3.3.2).

3. A conventional system is automatically s et up when a new programming file is created. If SMARTNET or SmartZone systems are also to be programmed, set them up as described in Section 3.1.11.

3.2.2 PROGRAMMING RADIO WIDE

PARAMETERS

1. To display the Radio Wide screens, click t he screen name under Radio Wide in the left pane or click t he Radio Wide button (see Section 3.1.9).

2. Program the applicabl e information i n these scr eens as described in Section 3.4.

3.2.3 PROGRAMMING CONVENTIONAL

CHANNELS

NOTE: If no conventional channels are programmed, skip this section.

1. Make sure the conventional system is displayed by clicking it in the left pane or selecting Window > Conventional in the menu bar.

Revised January 2001 Part No. 001-7780-501

3-4

Page 31

PROGRAMMING

2. If required, display the Conventional System programming screens by cli cking the System button or selecting Window > Conventional System (see Section 3.1.9).

3. Program the conventional systems and channels as described in Section 3.5.

3.2.4 PROGRAMMING SMARTNET AND

SMARTZONE SYSTEMS

NOTE: If no SMARTNET or SmartZone systems are programmed, skip this section.

1. Make sure the desired SMARTNET or SmartZone system is displayed by clic king it in the lef t pane or selecting W i ndow > SMARTNET or SmartZone in the menu bar.

2. If required, display the screens for that system by clicking the System button or selecting Window > Desired System (see Section 3.1.9).

3. Program the SMARTNET/SmartZone system and talk groups as described in Section 3.6.

4. To program additional SMARTNET/SmartZone systems, add a new system as described in Section

3.1.11 and repeat Section 3.6.

3.2.5 PROGRAMMING RADIO

(DOWNLOADING FILE)

3.3 MENU COMMANDS

Menu Bar

3.3.1 FILE MENU

New - Creates a programming file with default parameters for the selected frequency range.

Open - Opens a programming file that was previously saved to disk. If a modified file is currently open, you are asked if that file should be saved before the new file is opened.

Close - Closes the curr ent file. If the file has b een modified and the c hanges have not been saved, you are asked if the changes should be saved before closing.

When all the required programming information has been entered in the various programming screens, the information can be pr ogrammed (download ed) into the radio. When downloading a file, be sure that all connections between the computer and radio are secure, the radio is turned on, and the proper serial port is selected (see Section 3.3.1).

Then select Download > P arameters to 98xx Mobile. If no file is currently loaded, a dialog box appears to select the desired file. If a file is already loaded when Download is selected, th e current file is transferred to the radio.

NOTE: The information which follows (Sections 3.3-

3.6) provides detailed descriptions of the parameters that are displayed in the various PCTrunk screens.

Save - Saves the current file to disk using the current file name.

Save As - Same as “Save” except you ar e pr ompte d to enter a new file name if desired.

Print - Prints the information in the current file.

Select Communications Port - Displays the Commu-

nications Port dialog box which is used to select the serial port that is used to connect the transceiver to the computer (see Section 3.1.4).

Exit - Closes the PCTrunk program. If the current file has been modified and the changes have not been saved, you are asked if the changes should be saved before closing.

Revised January 2001

3-5

Part No. 001-7780-501

Page 32

PROGRAMMING

3.3.2 RADIO SERIES MENU

The Radio Series menu show above selects the

radio type (9883 Mobile) being programmed.

3.3.3 DOWNLOAD MENU

Parameters to 98xx Mobile - Transfers the current programming file to the radio connected to the computer.

DSP Code to 98xx Mobile - This function along with a special DSP upgrade file from E.F. Johnson are used to upgrade the DSP firmware. To put the radio in download mode, power the radio off, temporarily connect the microphone, and power it back on while pressing the microphone PTT switch. The DSP download mode is then i ndicat ed by “ CODE” in the d ispla y. The microphone is then disconnected, the RPI connected, and the code downloaded.

3.3.4 UPLOAD MENU

The Upload Menu is displayed only in the opening screen before a programming file is created. The following options are displayed:

3.3.5 SYSTEMS MENU

The Systems Menu is us ed to create new SMARTNET and SmartZone systems. It is also used to delete current systems. Conventional systems cannot be added because only one can be created. Refer to Section 3.1.11 for more information.

3.3.6 TOOLS MENU

The Tools > Convert File Format function is not used with this transceiver. It converts Format 5.4 files to the 5.5 format. All 98xx models use Format 5.5.

3.3.7 WINDOW MENU

The Window Menu is used to select the system to be edited. It can also be used to pop one of the screens to the front. Refer to Section 3.1.9 for more information.

3.3.8 HELP MENU

Parameters from 98xx Mobile - Transfers the programming data from a radio to the PCTrunk program. This data can then be viewed, edited, or saved to a disk file as desired.

Version Information from 98xx Mobile - Displays the software version number and serial number of the connected radio.

Revised January 2001 Part No. 001-7780-501

Contents - Displays the help system table of contents.

Search For Help On - Displays the sear ch dia log box

that allows searching for a help topic by keyword .

About PCTrunk - Displays the software version number of PCTrunk and other information.

3-6

Page 33

PROGRAMMING

3.4 RADIO-WIDE PARAMETER SCREENS

3.4.1 INTRODUCTION

The radio-wide screens program the parameters that are the same for all systems, channels, and zones. Separate screens are used for General, Conventional, SMARTNET/SmartZone, and Mobile Options parameters. Refer to the infor mation which follows.

3.4.2 RADIO-WIDE GENERAL SCREEN

Delete (Zones) Button

- Deletes the last zone a dded.

Defaults

Home Zone

- Selects the z one that is selected by the

Home Zone option switch if programmed.

Options

Power-Up On Home Zone

- If checked, the home

zone is always selected at power-up.

Beeps

- If checked, all tones are ena bled. Otherwise,

no tones sound (see Section 2.3.8).

NOTE: With PCTrunk, Version 5.10.0 or later, the following screens are selected by clicking their name in the left pane, not by clicking the button in the General screen.

Radio Wide Scan List

Band

Displays the operat ing band sel ected by the Radi o Type Menu (see Section 3.3.2). The selected operating band must match that of the radio being programmed.

Zones

T otal Zones

- The total numb er of zones cur rently set up. The maximum number allowed is 16. Zones are added by clicking the Add button (see following).

Current Zone

- Indicates the currentl y select ed zone.

To select another zone, click the up/down arrows.

Zone Alias

- Edits the unique alpha identification for the displayed zone. Up to 8 characters can be entered. The zone alias is briefly displayed whenever a new zone is selected. Refer to Section 1.5.3 for more information on zones.

NOTE: The radio-wide scan list cannot be programmed until all channels to be included have been set up as described in the Conventional and SMARTNET/SmartZone sections (3.5 and 3.6, respectively).

Clicking the Radio Wide Scan List name in the left pane or that button in the General screen displays the following screen which programs the radio-wide scan list described in Section 2.3.11. The buttons and other parameters in this screen are as follows:

Add (Zones) Button

- Adds another zone.

3-7

Radio-Wide Scan List Screen

Revised January 2001

Part No. 001-7780-501

Page 34

PROGRAMMING

Button - Disp lays the fo llowing

screen that selects the channels in each Zone and System that are in this scan list. Select each Zone and then the channels to be included from that zone.

Delete Entry

- Deletes the sel ected channel fr om the

scan list.

Scan Hold Time

- This programs the delay that occurs before radio-wide scanning resumes after a message is no longer being received. Times of 0 - 7.5 seconds can be programmed (see Section

2.3.11).

Assign Function Buttons Screen

2. To program a switch, click the arrow to display the pull-down menu and then select t he desired functi on from that menu.

3. Repeat for all switches and modes to be programmed and then exit this screen by clicking the Close button.

3.4.3 RADIO-WIDE CONVENTIONAL SCREEN

Modify List Screen

Assign Function Buttons

Clicking “Assign Functions Buttons” in the left pane or that button in the General screen displays the following screen which programs the five front panel option switches. These switches can be programmed with a different set of functions for each operating mode (conventional and SMARTNET/SmartZone). Refer to Section 2.3.4 for more information.

Program the option switches as follows:

1. In the System Type pull-down menu, select the

mode to be programmed (either conventional or SMARTNET/SmartZone).

Revised January 2001 Part No. 001-7780-501

The radio-wide conventional screen is shown above, and it is used to program the DTMF ANI ID. This ID is used on channels programmed for pre- or post-transmit ANI (see Section 3.5.4) and consists of eight digits from 0-9.

3.4.4 RADIO-WIDE SMARTNET/SMARTZONE

SCREEN

The radio-wide SMARTNET/SmartZone screen is shown on the next page, and it is used to program the following parameters:

Full Spectrum CC Scan

In a SmartZone system, if all potential control channel frequencies have been searched, the radio enters a channel-by-channel search across the full spectrum that the radio covers. The timer sets the time

3-8

Page 35

Radio Wide SMARTNET/SmartZone Screen

it performs this scan before it checks the expected frequencies again. After it checks these frequencies, it returns to full spectrum scanning. This cycle repeats until a control channel is found.

PROGRAMMING

Scan Talkback

When a message is received when scanning, this parameter selects how the radio responds during the call hang time. “Selected Group” forces it to transmit on the selected talk group, and “Active Group” forces it to transmit on the scanned or active talk group.

Voice On Control

With Smar tZone operation, some remote sites ar e designated Voice On Control sites. In these sites, if all available traffic channels are occupied, control channels become traffic channels when additional traffic channels are requested. The Voice On Control parameters determine how the radio reacts to various situations that may occur. For example, when a conversation is complete, the radio may look for a control channel that has become a traffic channel.

Enable/Disable parameters are active.

- Determines if the voi ce on contro l

On-Off

Timer occurs as just described.

Hot DTMF

Enable/Disable send DTMF tones while transmitting. When disabled, pressing n umer ic keys (0-9, , #) while transmitting has no affect.

Display Options

group calls are received (see Section 2.5.3). If neither function is selected, the selected talk group alias is always displayed. Both cannot be selected.

Talk Group on Rx which the call is being received is displayed.

- Enables or disables full spectrum scan.

- Sets the time that full spectrum scanning

- When enabled, allows the user to

These functions select what is displayed when

- The alias of the talk group on

Site Lock Ti me remains on the Voice On Control site before looking for another site.

Activatio n Time radio waits when the control channel comes back from Voice On Control before it transmits any pending ISWs. This prevents all radios on a Voice On Control site from submitting ISWs at the same time.

Pending Emergency Time time the radio waits to submit an Emergency ISW after the con trol channel returns from the Voice On Control m ode.

Adjustable Parameters

Busy Override Delay this is the amount of ti me a user must press the PTT switch to override a SmartZone busy that occurs because some member of the talk group is prese nt at a site where there are no traffic channels available.

- This is the a mount of time a radio

- This is the amount of time the

- This is the amount of

- With SmartZone operation,

PTT ID displayed. If the ID matches an ID in the Trunking Call List, the alias of that ID is displayed instead.

- The ID of the mobile placing the call is

3-9

Affiliate Hold Of f is the delay time that occurs after acquiring the control channel before it sends an affiliation ISW.

- With Smar tZone operati on, this

Revised January 2001

Part No. 001-7780-501

Page 36

PROGRAMMING

This prevents all radi os on the sys tem from sendi ng affiliation ISWs at the same time.

Failsoft Inactivity

- Programs failsoft op eration (see Section 2.5.11). If the radio remains inactive (no receive or transmit activity on channel) while operating in the fail soft mode f or the pro gramme d time, the radio momentarily leaves the failsoft mode and attempts to find a control channel. If “0” is programmed, the radio does not leave the failsoft mode.

3.4.5 RADIO-WIDE MOBILE OPTIONS SCREEN

Minimum V o lume

- Sets the minimum volume level that can be selected by th e volume control. Thi s can be used to prevent miss ed messages c aused by inad vertently turning t he volume d own to o far. Relative levels of 0-255 can be set (“0” sets the lowest minimum volume).

3.5 PROGRAMMING CONVENTIONAL SYSTEMS AND CHANNELS

3.5.1 INTRODUCTION

The following information describes how conventional channels are programmed. Conventional systems do not need to be set up because only one can be programmed, and it is automatically set up when the programming file is selected as described in Section 3.1.6. Up to 256 conventional chann el s can be programmed (if no SMARTNET/SmartZone systems are programmed). Refer to Section 1.5.3 for more information on systems and channels.

The following is the recommended procedure for programming conventional channels:

The radio-wide Mobile Options screen is used to

program the following parameters:

Backlight Level

- Selects the defaul t backlight level whenever power is on. This setting can be overridden by the backlight option switch if it is programmed.

Hang-Up Box Monitor

- Selecting “Off” disables microphone off-hook detection. Taking the microphone off-hook th en does not disable coded squel ch functions or scanning. Selecting “On” enables microphone off-hook detection.

Ignition Power Down Time

- When the ignition switch controls transceiver power , this sets the delay that occurs between when the ignition switch is turned off and when transceiver power actually turns off. Times of 0-254 minutes can be programmed or an infinite time (no turn-of f) can be selected (Section 2.3.9).

1. Program the radio- wide info rmation as descr ibed in Section 3.4.

2. If other types of systems are programmed, make sure the conventional system is selected in the left pane or by sele cting Window > Conventional in t he menu bar (see Section 3.1.9).

3. Program the conventional system information and then the channel information as follows.

3.5.2 CONVENTIONAL SYSTEM GENERAL

SCREEN

The conventional system Gene ral screen is shown on the next page, and it programs the following parameters:

Timers

Tx Time-Out Timer

- This timer li mits the lengt h of transmissions (Section 2.3.7). Times up to 3 minutes, 45 seconds in 15-second steps can be programmed.

Revised January 2001 Part No. 001-7780-501

3-10

Page 37

PROGRAMMING

Penalty Timer - This timer disables tr ansmitting after the time-out timer expires (Section 2.4.7). Times up to 3 minutes, 45 seconds in 15-second steps can be programmed.

Conversation Timer

- This timer limits the total

length of a conversatio n (Section 2.4.8). T imes up to

7.5 minutes in 0.5-minute steps can be programmed.

Scan List Button

Clicking Scan List in the left pane or that button in the General screen displays the preceding screen which is used to program the conventional scan lists described in Section 2.4.11.

NOTE: The conventional scan lists cannot be programmed until all the conventional channels are programmed . Therefore, first progra m the cha nnel s as described in Sections 3.5.3 and 3.5.4.

To modify a list, click and the screen which follows is displayed. Select the desired scan list in the box on the top and then select the zone and the channels f rom th at zone to be incl uded. Repeat for each zone. Do this for each list programmed. The

button deletes the selected channel(s)

from the scan list.

Conventional System Ge neral Screen

Busy Channel Override - Selects if the busy channel lockout feature ca n be over r idden by quickly releasing and then pressing the PTT switch (see Section 2.4.5).

Conventional System Modify Scan List Screen

The following parameters are programmed in the Conventional System Scan List Screen shown on the left.

Keypad Editing

Conventional Syste m Scan List Screen

This function selects if the user is allowed to edit the scan list. This requ ires the Scan Edit option switch

Revised January 2001

3-11

Part No. 001-7780-501

Page 38

PROGRAMMING

as described in Section 2.3.11. User editing can be enabled and disabled on each scan list.

Scan Mode

Sets the channel on which transmissions occur when the PTT switch is pressed while scanning. A different mode can be programmed for each scan list. In addition, it selects if priority samp ling is used and also the type of priority channel (see the “Priority Channel” description which follows). The following modes are available:

No Priority - Priority sampling does not occur (all channels are scanned in sequence). The radio transmits on the selected channel.

Priority/Tx Priority - Priority sampling occurs and the priority channel is the one programmed in the selected scan list. The radio transmits on the priority channel.

Priority/Tx Selected - Priority sampling occurs and the priority channel is the one programmed in the selected scan list. The radio transmits on the selected channel.

Priority on Sel Chan - The priority chann el is always the selected channel (even if the scan list is programmed with a priority channel). The radio transmits on the selected channel.

Talkback Scan - No priority sampling occurs (even if the scan list is programmed with a priority channel). The radio transmits on the channel of a call while scanning is halted. Then when scanning resumes, it transmits on the selected channel.

Scan Timers

rect Call Guard (CTCSS/DCS) code is detected. Since it takes much longer to detect an incorrect Call Guard signal tha n a carrier, this time should be relatively long to prevent the interruptions from making a message difficul t to unders tand. Times of

0.5-8.0 seconds can be programmed in 0.5-second steps.

Priority Channel Selection

The Scan Mode parameter in the preceding Conventional System Scan List screen selects if priority channel sampling is enabled on the selected scan list. It also selects the type of priority channel (either fixed or the selected) if applicable.

If the “Priority/Tx Priority” or “Priority/Selected” mode is programmed, fixed priority channel sampling is selected. The fixed priority channel must then be chosen for the scan list. To do this, click the

button in the preceding Modify Sca n List screen and then select the desired zone/channel. Refer to Section 2.4.12 for more information on priority channel sampling.

3.5.3 SETTING UP CONVENTIONAL

CHANNELS

The conventional Channel screen shown in Figure 3-3 which follows is displayed when a conventional channel is selected. This screen programs unique channel parameters and also assigns channels to the selectable zones displayed by the transceiver.

The general procedure for setting up a conventional channel is as follows. Refer to the descriptions which follow this procedure for information on the parameters in the channel screens.

Scan Hold Time - Sets the delay that occurs before scanning resumes after a signal is no longer received (see Section 2.3.11).

Lookback Time A - This time determines how often the priority channel is checked for activity. Times of 0.25-4.00 seconds in 0.25-second steps can be programmed.

Lookback Time B - This time determines how often the priority channel is checked once an in cor-

Revised January 2001 Part No. 001-7780-501

1. Make sure that the desired zone is selected in the

Zone box.

2. Select the channel number in the Channels Index

box which is to be progra mmed with the c hannel. If the channel number display mode is selected (see Section 2.4.2), this will be the number displayed when the channel is selected.

3. To assign a conventional channel, select “Conven-

tional” as the channel type.

3-12

Page 39

PROGRAMMING

Figure 3-3 Conventional Channel Screen

4. Click the Modify button to display th e screen which enables that channel and programs the alias (tag) and transmit and rece ive frequencies. The n program the other parameters in the main part of the screen. Refer to the next section for more information .

3.5.4 CONVENTIONAL CHANNEL SCREEN

PARAMETERS

The following parameters are programmed in the

conventional channel screen shown in Figure 3-3.

Selected Channel

Zone Box

- Clicking the arrow to the right of this box displays the avail able zones. Cli ck on a zone to select it. Zones and zone aliases are set up on the Radio-Wide General screen described in Section

3.4.2.

Channel Index Box

- Displays the availab le channels in the selected zone. The channel type is selected by the Channel Type box below it.

Modify Button - Displays the small

screen shown in Figure 3-3 which enables the

channel (makes it selectable) and programs t he alias (tag) and transmit and receive frequencies.

The parameters in this s creen are as follows:

Channel - Selects the channel to be edited. Alias - Programs the identification that is displayed

when the channel is selected. Up to 8 characters can be programmed.

Transmit - Programs the transmit freque ncy of the

channel.

Receive - Programs the receive frequency of the

channel.

Enable This Channel - The bo x must be che cked fo r

the channel to be selectable.

Rx Only - The box is checked if the channel is

receive-only (transmitter disabled).

Copy Parameters From Channel - If another channel

is selected, the parameters from tha t channel are copied to the new channel.

NOTE: Channel numbers not assigned must be programmed for conventional operation and then not enabled in the Modify screen because SMARTNET/ SmartZone channels cannot be disabled.

3-13

Revised January 2001

Part No. 001-7780-501

Page 40

PROGRAMMING

Channel Type

Channel Type Box

- Selects the specific system from which the channel is se lected. All programmed systems are displayed by numbe r and type (co nventional, SMAR TNET, SmartZone). When a different channel type is selected, the screen for that type of channel is automatically displayed.

System Specific Information

- With conventional systems, indicates the frequency of the selected channel without having to select the Modify box.

Transmit Power

This fixes the transmit power on the channel for the high or l ow level or allows it to be switch selectable (the Hi/Lo Power option switch is then required). Refer to Section 2.4.10 for more information.

Tx Time-Out

This enables or disables the time- out timer on the channel. The time- out timer ti me is pro grammed in the conventional system General screen (Section 3.5.2).

Busy Channel Lockout

Off = disabled, Noise = transmit disallowed if carrier is detected, Tone = transmit allowed with carrier detected only if correct Call Guard (CTCSS/ DCS) code is detected.

Coded Squelch

Trailing ANI

- A DTMF-coded ID is sent at the e nd

of each transmission.

Channel Modulation

This selects if the channel modulation is wide-

band (5 kHz) or narrowband (2.5 kHz).

3.6 PROGRAMMING SMARTNET/SMARTZONE SYSTEMS AND CHANNELS

3.6.1 INTRODUCTION

To program SMARTNET and SmartZone

systems and channels, proceed as follows:

1. Program the SMARTNET/SmartZone radio-wide

information as described in Section 3.4.

2. To create a new SMARTNET/SmartZone system,

select the Systems > Add Systems in the menu bar (see Section 3.1.11). Up to sixteen systems of any type can be programmed as described in Section

1.5.3.

3. Program the SMAR TNET/Smart Zone syste m infor-

mation as described starting in the next section. Make sure the desired SMARTNET or SmartZone system is displa yed by cl ickin g it in the left p ane or selecting it in the Window menu in the menu bar (see Section 3.1.9). Then program the channels as described starting in Section 3.6.8.

3.6.2 SMARTNET/SMARTZONE SYSTEM

GENERAL SCREEN

This sets the transmit and receive Call Guard (CTCSS/DCS) coding, if any, used on the channel. If “None” is selected, no code is transmitted and carriercontrolled squelch is used when receiving (Section

2.4.6). The standard Call Guard tones and codes are listed in Table 3-1 on page 3-23.

Signaling

Off

- No ANI signaling is used.

Leading ANI

- A DTMF-coded ID is sent at the beginning of each tra nsmission. Thi s ID is set i n the radio-wide conventional screen (Section 3.4.3).

Revised January 2001 Part No. 001-7780-501

The SMARTNET/SmartZone System General screen is shown on the next page, and it programs the following parameters:

Restricted Access

Change System ID

- Clicking Change System ID in the left pan e or that button in the Gen eral screen displays the Change Sys tem ID screen which is used to enter the system ID of the system. This ID is entered as a h exadecimal n umber from 0-9 and A-F. Valid numbers are from 0001-FFFF. The system ID corresponding to th e desired ID must also be located in the “key” subdirectory of the program file.

3-14

Page 41

PROGRAMMING

System ID - Read-onl y fie ld whi ch shows the I D of the system currently being edited.

SMARTNET/SmartZone System General

Screen

Splinter Channels

When splinter channels are enabled, the receive and transmit frequencies are 12.5 kHz lower than the normal frequencies . Spl int er cha nnels are used only as required in the Mexico and Canada border areas for frequencies between 806 and 820.975 MHz.

Channel Modulation

When “Wideband” is enabled, the radio operates with a 4 kHz maximum deviation between 821.000 and 824.975 MHz and 5 kHz maximum deviation for all other frequencies. When it is disabled, deviation is 5 kHz with all frequencies.

PTT ID

This enables or disables the PTT ID.

Transmission Trunking

System Lists

Clicking System Lists in the left pane or that button in the General screen displays the screens used to program the various lists that are unique for each SMARTNET/SmartZone system. Refer to Section

3.6.7 for more information on these lists.

Dynamic Regrouping

Enable For This System

- When this box is checked, a dynamic regrouping channel is enabled. This is a SMARTNET chan nel which has the cor res pon din g talk group dynamically set by the dispatcher.

Zone

- The physical zone containing the dynamic regrouping channel. The value is selected on the Channel Parameters screen.

Channel

- The physical channel used for dynamic regrouping. The value is selected on the Channel Parameters screen.

Affiliation Type

Automatic

- The radio immediately affiliates with the central controller as soon as it is turned on and automatically re-affiliates each time the talk grou p is changed .

On PTT

- The radio affiliates with the central

controller only when the PTT switch is pressed.

Time-Out Timer

This programs the time-out timer setting for the system. It can be programmed for 0 min, 15 sec up to 3 min, 45 sec or it can be disabled (see Section 2.3.7).

ISW Delay Time

Increasing or decreasing this value changes the transmission timing of ISWs relative to the reception of OSWs.

Selecting “Disabled” removes the hang time at the end of a normal convers atio n. This for ces the radio to always contact the control channel when seeking a channel grant instead of being able to key up on the hang time of another conversation.

3.6.3 SMARTNET/SMARTZONE SYSTEM OTHER ID’S SCREEN

The SMARTNET/SmartZone Other ID’s screen

follows, and it programs the these parameters.

Revised January 2001

3-15

Part No. 001-7780-501

Page 42

PROGRAMMING

SMARTNET/SmartZone Other IDs Screen

Individual ID - Uniquely identifies the radio on a particular system. Each radio must have a different Unit ID. Valid Unit IDs are from 1-65535.

Connect Tone

- The tone expecte d by th e co ntrol ler on the traffic channel to verify that a subscriber transmission is occurring. This tone should be set the same as it is in the con troller.

3.6.4 SMARTNET/SMARTZONE SYSTEM PHONE INTERCONNECT SCREEN

List Only

- Telephone calls can be placed and received, and numbers can be recalled from memory only.

Unlimited

- Tel eph one cal ls can be placed and received, and numbers can be recalled from memory or dialed using a microphone keypad.

Private Call

This is the same as the preceding Phone Interconnect except it is fo r private (unit-to -unit) ca lls. Refer to Sections 2.5.4 and 2.5.5 for more information.

Private Call II

This programs either standard (Private Conversa-

™

tion II tion

) or enhanced (Enhanced Private Conversa-

™

) private calls as follows:

Standard

- The user does not receive any feedback when the called radio is not active in the system. Only a “No Answer” is received if the called radio does not answer.

The SMARTNET/SmartZone Phone Interconnect screen is shown above, and the parameters it programs are as follows:

Phone Interconnect

Refer to Section 2.5.6 for more information on telephone calls.

Disabled

- Telephone calls cannot be placed or

received.

Enhanced

- When a call is placed, the system tells the user if the called radio is currently active in the system and within range. The call ing radio dis plays “NO ACK” if the called radio is not active in the system and “NO ANSWR” if it is active but does not answer.

Phone DTMF Timing

Initial Delay

- Delay from 50-500 mi lliseconds from when a traffic channel is granted for phone int erconnect to the start of the dialing out of the phone number.

Digit Duration

- Duration from 50-500 mill iseconds

of each phone number digit.

Inter-Digit De lay

- Delay from 50-500 mil liseconds

between each digit of a phone number.

3.6.5 SMARTNET/SMARTZONE SYSTEM TALK GROUPS SCREEN

Answer Only

- Telephone calls can be received but

not placed.

Revised January 2001 Part No. 001-7780-501

The SMAR TNET/Smar tZone Talk Groups screen

is used to set up SMARTNET/SmartZone talk groups

3-16

Page 43

SMARTNET/SmartZone System Talk Groups

Screen

and program unique talk group information. This screen is shown on the next page, and the pa ramete rs it programs are as follows:

PROGRAMMING

3.6.6 SMARTNET/SMARTZONE SYSTEM EMERGENCY SETTINGS SCREEN

The SMARTNET/SmartZone Emergency Settings screen and the parameters it programs are as follows:

T alk Group

- Selects the talk group to progr am. This is the actua l ID of the talk group. Talk groups are added or deleted by clicking the Add TG or Delete TG button (see following). T al k groups are assigned to channels on the channel screen (see Section

3.6.9).

- Clicking this b utton dis plays a di alog box that adds a new ta lk group. Th e alias ( alphatag ) of up to 8 characters is entered, and the new group is then added after the others that are already set up. Each SMARTNET/SmartZone system can be programmed with up to 256 talk groups.

- Clicking this button deletes the currently selected talk group (the one displayed in the “Talk Group” box).

Failsoft Channel

Enable

- Enables a failsoft channel on the talk group

if a controller failure occurs (see Section 2.5.11).

Disable

- The failsoft mode is not entered if the

controller fails.

Emergency Call

Enable

- When the Emergency option switch and then the PTT switch are pressed, an emergency group call is transmitted .

Disable

- An emergency group call is not

authorized.

Emergency Hot Mic

Enable

- When an emergency alarm is generated and the emergency alarm acknowledgment received, the emergency mode is automatically entered and transmitting begins for the time specified by the Tx Pe riod parameter (see following).

Disable

Tx Period

- Automatic transmissions do not occur.

- Defines the period during which transmissions occur with the microphone audio unmuted (without user inter vention). Ti mes of 10-120 seconds in 10-second steps can be selected.

Emergency Alarm

Tx/Rx Frequency

- Programs the failsoft channel

frequency if “Enabled” is checked.

3-17

Disabled

- No emergency signal is sent when the

user presses the Emergency option switch.

Revised January 2001

Part No. 001-7780-501

Page 44

PROGRAMMING

Normal - When the user presses the Emergency option switch, an emergency signal is sent to the dispatcher. Audio and visual feedback is provided by the radio.

Silent

- Same as “Normal” except no audio or visual

feedback is provided.

Retry Counter

- When “Unl imited” is selected, an emergency call is repeated until acknowledged or canceled. When “Limited” is checked, calls are attempted only the specified number of times.

3.6.7 SMARTNET/SMARTZONE SYSTEM LISTS SCREENS

Clicking System Lists in the left pane or the

button in the SMARTNET General screen (if applicable) disp lays the scree ns used to program the various lists that are unique for each SMARTNET/ SmartZone system. These screens are as follows:

Trunking Phone List Screen

Entry Alias

- Up to 8 characters can be entered to identify the phone number. This identification is displayed when phone numbers are selected by the user from the list. Only uppercase letters can be entered, so lowercase letters are automatically converted to uppercase by the program.

Phone Number

- This is the number dia led when the location is selected. Characters that can be entered include 0-9, #, (,), and P (a “P” programs a pause). The maximum number of digits excluding (,) and spaces is 16, and the maximum including (,) and spaces is 24.

- Clicking this button verifies the current entry , stor es it, and then c loses the dialog box. If the current entry contains an invalid field, the dialog box does not close and the invalid field is highlighted.

Help

- Accesses the Help screen. Help can also be

selected at any time by pressing the F1 key.

This screen programs the phone number list if used (see Section 2.5.6). To edit this list, click the Trunking Phone List tab and then the “Modify List” button on the right side of the screen. The following information is then programmed in the dialog box that is displayed:

Entry Number

- This box selects the entry to be edited. The scroll bar s to the r ight of this box se le ct the desired entry. A phone list can contain up to 16 entries. Select ing a new entr y number autom atically validates and stores the current entry. If the current entry contains an invalid field (for example, too many digits in the phone number), the entry numbe r does not change and the inva li d fi eld is highlighted.

Message Aliasing Screen

This screen associates an alias (name) with each message number (see Section 2.5.8). To edit this list, click the Message Aliasing tab and then the “Modify List” button on the right side. The following information is then programmed in the dialog box that is displayed:

Message Number

- This box selects the messa ge to be edited. T he scroll bars to the right of this box select the desired message number.

Message Alias

- Programs the alia s which can b e up

to any 8 alphanumeric characters.

Revised January 2001 Part No. 001-7780-501

3-18

Page 45

PROGRAMMING

Close Button - Validates the entry and closes the dialog box. The entry is a lso validated when anothe r message number is selected.

Announcement Groups Screen

This screen programs the announcement groups that are used to communicate with several talk groups simultaneously. There can be up to 3 announcement groups per system, and each announcement group can have up to 15 talk groups.

T o cre ate an ann ouncement group, cli ck the “Add AG” button and the “Add TGs to the AG” screen shown above is displayed. Enter the announcement group ID, click t he talk groups to sele ct/de-s elect t hose that are to be included, and then create the announcement group by clicking the “Create AG” button. To delete the current announcement group, click the “Delete AG” button.

To edit an announcement group, click the “Modify List” button on the right and the preceding screen is displayed. Select the announcement group to be edited from a pull-do wn menu s elect ing by cl icki ng the “AG” arrow. Then click the talk groups to select/ de-select them and th en click the “Update List” button to make the changes.

Control Channels Screen

This screen allows the system manager to view and edit the control channels. Each SMARTNET system can have up to four control channels, and each SmartZone system can have up to 32 control channel s. Only one control channel is active at a time.

To edit this list, click the Control Channels tab and then the “Modify List” button on the right side. The following information is then programmed in the dialog box that is displayed:

3-19

Control Channel

- Selects the control cha nnel to be edited. T o add a ne w channel, click th e “New Entry” button.

Frequency

- The transmit and receive frequency of the control channel. These are the mobile frequencies, not the r epeater frequen cies. Only multipl es of 5 kHz and 6.25 kHz are valid. With 800 MHz frequencies, a receive fr equency 45 MHz above the transmit frequency is automatically entered.

New Entry Button

- Click this button to display the

dialog box used to add another control channel.

Revised January 2001

Part No. 001-7780-501

Page 46

PROGRAMMING

Trunking Call List Screen

This screen allows the list of IDs used for private calls to be programmed . A maximum of 16 I D s ca n be programmed (see Sections 2.5.4 and 2.5.5).

To edit this list, click the Trunking Call List tab and then the “Modify List” button on the right side. This following information is then programmed in the dialog box that is displayed:

Priority Monitor Scan Screen

Entry Number

- This box selects the entry to be edited. The scroll bar s to the r ight of this box se le ct the desired entry . A private call li st can contain up to 16 entries. Selecting a new entry number automatically validates and stores the current entry. If the current entry contains an invalid field, the entry number does not change and the invalid field is highlighted.

Entry Alias

- Up to 8 characters can be entered to identify the user being called. This identification is displayed w hen the mobi le to be called is selected by the user from the list . Onl y upperc ase le tt ers c an be entered, so lowercase letters are automatically converted to uppercase by the program.

Call ID

- This is the ID of the radio being called. Valid entries are 1-65535. A “0” is detected as no entry.

Close Button

- Verifies the current entry, stores it, and then closes the dialog box. If the current entry contains an invalid field, the dialog box does not close and the invalid field is highlighted.

This screen programs up to thr ee Priori ty Monitor scan lists that are allowed. Each scan list can contain up to 15 channels plus a priority channel (see Section

2.5.12). These channels must be from the same SMARTNET/SmartZone system. Channels set up for other systems are not allowed.

To edit a list, click the Priority Monitor Scan ta b and then click the “Modify List” button on the right side. A screen similar to the bottom screen shown above is then displayed to select the channels to be included in that scan list. Select channels as follows:

1. Select the scan l ist to be edit ed by clicking th e scroll

bars next to the “Scan List To Modify” box.

2. Select the first zone with channels to be included

and select the d esired chann els. Repeat f or the other zones.

3. To select the priority channel, click the Set Priority

button. Then select the desired Zone/Channel or “None” if no priority channel is to be scanned.

Revised January 2001 Part No. 001-7780-501

3-20

Page 47

PROGRAMMING

Figure 3-4 SMARTNET/SmartZone Channel Screen

4. Repeat the prece ding st eps f or the ot her s can l ists if applicable.

Stat us Ali asi ng Screen

This screen is shown above, and it programs the alias for each of up to eight status conditions that can be sent. The meaning of each status number is define d by the system manager. Refer to Section 2.5.9 for more information.

To edit this list, click the Status Aliasing tab and then the “Modify List” button on the right side. The following information is then programmed in the dialog box that is displayed:

Status Number

- The scroll bars to the right of this

box select the status number that is to be edited.

Status Alias

- Programs up to 8 char acter s tha t iden tify the status. Th is id entificati on is di splayed whe n the user selects a status condition.

3-21

Revised January 2001

Part No. 001-7780-501

Page 48

PROGRAMMING

3.6.8 SETTING UP SMARTNET/SMARTZONE CHANNELS

The SMARTNET/SmartZone Channel screen shown in Figure 3-4 is displayed when the SMARTNET or SmartZone channel type is selected. This screen programs unique channel parameters and also assigns cha nnel s to the selectable zones displayed by the transceiver.

The general procedure for setting up a SMARTNET/SmartZone channel is as follows. Refer to the descriptions which follow this procedure for information on SMARTNET/SmartZone Channel screen parameters.

1. Make sure that the desired zone is selected in the

Zone box.

2. Select the channel number in the Channels Index

box which is to be programmed with the channel.

3. To set up a SMARTNET channel, select

“SMARTNET” as the channel type, and to set up a SmartZone channel, select “SmartZone”.

Channel Index Box

- Displays the channels in the selected zone. The channel type is selected by the Channel Type box below it.

- Displays the screen shown in the lower part of Figure 3-4. The parameters programme d in this screen are as follows:

Channel - Selects the channel to be edited. Alias - Programs the identification that is displayed

when the channel is selected. Up to 8 characters can be programmed.

Transmit - Not programmable because the transmit

frequency is dynamicall y assigne d over the air (“Trunked” is always displayed).

Receive - Dynamically assigned like the transmit

frequency.

Enable This Channel - Not used because SMART-

NET/SmartZone channels are always enabled if set up. To disable a channel so that it is not selectable, choose the conventional type and do not check this box.

Copy Parameters From Channel - If another channel

is selected in the box, the parameters from that channel are copied to the new channel.

4. Click the Modify button to display the dialog box shown in the lower part of Figure 3-4. This box programs the alias (tag) that is displayed when it is selected.

5. Program the other parameters in th e main part of the screen (see information which follows).

3.6.9 SMARTNET/SMARTZONE CHANNEL

SCREEN PARAMETERS

The following parameters are programmed in the SMARTNET/SmartZone channel screen shown in Figure 3-4.

Selected Channel

Zone Box

- Clicking the arrow to the right of this box displays the avail able zones. Cli ck on a zone to select it. Zones and zone aliases are set up on the Radio-Wide General screen described in Section

3.4.2.

Channel Type

Channel Type Box

- Selects the specific system from which the channel is se lected. All programmed systems are displayed by number and typ e (conven tional, SMAR TNET, SmartZone). When a different channel type is selected, the screen for that type of channel is automaticall y disp la yed.

Other Screen Parameters

System Specific Information

- With SMARTNET/ SmartZone systems, indicates the system ID programmed on the system General screen (see Section 3.6.2).

Talk Group

- Selects the talk group selected by that channel. Talk groups are programmed in the Talk Group screen described in Section 3.6.5.

Announcement Group

- Selects one of up to three announcement groups selected by the channel. Refer to “Announcement Gro up Scre en” in Sect ion

3.6.7 for more information.

Revised January 2001 Part No. 001-7780-501

3-22

Page 49

PROGRAMMING

Emergency Group - Selects the talk group used for emergency calls.

Talk Permit T one

- When enabled, a short tone sounds after a request for a group call has been approved by the main controlle r. This indicates that speaking can begin. When disabled, no audio feedback is used to indicate when speaking can begin.

System Scan

- Selects the Prior ity Monitor Sc an list

selected by the chan nel (see “P riority Monitor Sc an

Table 3-1 Call Guard (CTCSS/DCS) Codes and Tones

Recommended Tone Call Guard Codes

Screen” description in Section 3.6.7). If “No Scan List” is programmed, scanning is not selectable on that channel.

Auto Scan

- When enabled and a channel is selected, the radio automat ically begin s scanning t he scan list associated with that channel. When disabled, scanning can only be started manually by the Scan option switch.

Code Freq Code Freq Code Freq Code Freq Code Freq

01 67.0 10 94.8 19 127.3 28 173.8 37* 241.8 02 71.9 11** 97.4 20 131.8 29 179.9 38* 250.3 03 74.4 12 100.0 21 136.5 30 186.2 39** 69.3 04 77.0 13 103.5 22 141.3 31 192.8 40** 206.5 05 79.7 14 107.2 23 146.2 32 203.5 41** 229.1 06 82.5 15 110.9 24 151.4 33 210.7 42** 254.1 07 85.4 16 114.8 25 156.7 34* 218.1 08 88.5 17 118.8 26 162.2 35* 225.7 09 91.5 18 123.0 27 167.9 36* 233.6 * These tones normally are not used because of their close proximity to the voice frequencies

** This tone is normally not used because it may cause interference with adjacent tones.

Recommended Digital Call Guard Codes

023 065 131 172 261 346 431 532 654 743 025 071 132 174 263 351 432 546 662 754 026 072 134 205 265 364 445 565 664 031 073 143 223 271 365 464 606 703 032 074 152 226 306 371 465 612 712 043 114 155 243 311 411 466 624 723 047 115 156 244 315 412 503 627 731 051 116 162 245 331 413 506 631 732 054 125 165 251 343 423 516 632 734

3-23

Revised January 2001

Part No. 001-7780-501

Page 50

PROGRAMMING

800 MHz Channels

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

1 851.0125 806.0125 2 851.0375 806.0375 3 851.0625 806.0625 4 851.0875 806.0875 5 851.1125 806.1125 6 851.1375 806.1375 7 851.1625 806.1625 8 851.1875 806.1875

9 851.2125 806.2125 10 851.2375 806.2375 11 851.2625 806.2625 12 851.2875 806.2875 13 851.3125 806.3125 14 851.3375 806.3375 15 851.3625 806.3625 16 851.3875 806.3875 17 851.4125 806.4125 18 851.4375 806.4375 19 851.4625 806.4625 20 851.4875 806.4875 21 851.5125 806.5125 22 851.5375 806.5375 23 851.5625 806.5625 24 851.5875 806.5875 25 851.6125 806.6125 26 851.6375 806.6375 27 851.6625 806.6625 28 851.6875 806.6875 29 851.7125 806.7125 30 851.7375 806.7375 31 851.7625 806.7625 32 851.7875 806.7875 33 851.8125 806.8125 34 851.8375 806.8375 35 851.8625 806.8625 36 851.8875 806.8875 37 851.9125 806.9125 38 851.9375 806.9375 39 851.9625 806.9625 40 851.9875 806.9875 41 852.0125 807.0125 42 852.0375 807.0375 43 852.0625 807.0625 44 852.0875 807.0875 45 852.1125 807.1125 46 852.1375 807.1375 47 852.1625 807.1625 48 852.1875 807.1875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

49 852.2125 807.2125 50 852.2375 807.2375 51 852.2625 807.2625 52 852.2875 807.2875 53 852.3125 807.3125 54 852.3375 807.3375 55 852.3625 807.3625 56 852.3875 807.3875 57 852.4125 807.4125 58 852.4375 807.4375 59 852.4625 807.4625 60 852.4875 807.4875 61 852.5125 807.5125 62 852.5375 807.5375 63 852.5625 807.5625 64 852.5875 807.5875 65 852.6125 807.6125 66 852.6375 807.6375 67 852.6625 807.6625 68 852.6875 807.6875 69 852.7125 807.7125 70 852.7375 807.7375 71 852.7625 807.7625 72 852.7875 807.7875 73 852.8125 807.8125 74 852.8375 807.8375 75 852.8625 807.8625 76 852.8875 807.8875 77 852.9125 807.9125 78 852.9375 807.9375 79 852.9625 807.9625 80 852.9875 807.9875 81 853.0125 808.0125 82 853.0375 808.0375 83 853.0625 808.0625 84 853.0875 808.0875 85 853.1125 808.1125 86 853.1375 808.1375 87 853.1625 808.1625 88 853.1875 808.1875 89 853.2125 808.2125 90 853.2375 808.2375 91 853.2625 808.2625 92 853.2875 808.2875 93 853.3125 808.3125 94 853.3375 808.3375 95 853.3625 808.3625 96 853.3875 808.3875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

97 853.4125 808.4125 98 853.4375 808.4375

99 853.4625 808.4625 100 853.4875 808.4875 101 853.5125 808.5125 102 853.5375 808.5375 103 853.5625 808.5625 104 853.5875 808.5875 105 853.6125 808.6125 106 853.6375 808.6375 107 853.6625 808.6625 108 853.6875 808.6875 109 853.7125 808.7125 110 853.7375 808.7375 111 853.7625 808.7625 112 853.7875 808.7875 113 853.8125 808.8125 114 853.8375 808.8375 115 853.8625 808.8625 116 853.8875 808.8875 117 853.9125 808.9125 118 853.9375 808.9375 119 853.9625 808.9625 120 853.9875 808.9875 121 854.0125 809.0125 122 854.0375 809.0375 123 854.0625 809.0625 124 854.0875 809.0875 125 854.1125 809.1125 126 854.1375 809.1375 127 854.1625 809.1625 128 854.1875 809.1875 129 854.2125 809.2125 130 854.2375 809.2375 131 854.2625 809.2625 132 854.2875 809.2875 133 854.3125 809.3125 134 854.3375 809.3375 135 854.3625 809.3625 136 854.3875 809.3875 137 854.4125 809.4125 138 854.4375 809.4375 139 854.4625 809.4625 140 854.4875 809.4875 141 854.5125 809.5125 142 854.5375 809.5375 143 854.5625 809.5625 144 854.5875 809.5875

Revised January 2001 Part No. 001-7780-501

3-24

Page 51

800 MHz Channels

PROGRAMMING

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

145 854.6125 809.6125 146 854.6375 809.6375 147 854.6625 809.6625 148 854.6875 809.6875 149 854.7125 809.7125 150 854.7375 809.7375 151 854.7625 809.7625 152 854.7875 809.7875 153 854.8125 809.8125 154 854.8375 809.8375 155 854.8625 809.8625 156 854.8875 809.8875 157 854.9125 809.9125 158 854.9375 809.9375 159 854.9625 809.9625 160 854.9875 809.9875 161 855.0125 810.0125 162 855.0375 810.0375 163 855.0625 810.0625 164 855.0875 810.0875 165 855.1125 810.1125 166 855.1375 810.1375 167 855.1625 810.1625 168 855.1875 810.1875 169 855.2125 810.2125 170 855.2375 810.2375 171 855.2625 810.2625 172 855.2875 810.2875 173 855.3125 810.3125 174 855.3375 810.3375 175 855.3625 810.3625 176 855.3875 810.3875 177 855.4125 810.4125 178 855.4375 810.4375 179 855.4625 810.4625 180 855.4875 810.4875 181 855.5125 810.5125 182 855.5375 810.5375 183 855.5625 810.5625 184 855.5875 810.5875 185 855.6125 810.6125 186 855.6375 810.6375 187 855.6625 810.6625 188 855.6875 810.6875 189 855.7125 810.7125 190 855.7375 810.7375 191 855.7625 810.7625 192 855.7875 810.7875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

193 855.8125 810.8125 194 855.8375 810.8375 195 855.8625 810.8625 196 855.8875 810.8875 197 855.9125 810.9125 198 855.9375 810.9375 199 855.9625 810.9625 200 855.9875 810.9875 201 856.0125 811.0125 202 856.0375 811.0375 203 856.0625 811.0625 204 856.0875 811.0875 205 856.1125 811.1125 206 856.1375 811.1375 207 856.1625 811.1625 208 856.1875 811.1875 209 856.2125 811.2125 210 856.2375 811.2375 211 856.2625 811.2625 212 856.2875 811.2875 213 856.3125 811.3125 214 856.3375 811.3375 215 856.3625 811.3625 216 856.3875 811.3875 217 856.4125 811.4125 218 856.4375 811.4375 219 856.4625 811.4625 220 856.4875 811.4875 221 856.5125 811.5125 222 856.5375 811.5375 223 856.5625 811.5625 224 856.5875 811.5875 225 856.6125 811.6125 226 856.6375 811.6375 227 856.6625 811.6625 228 856.6875 811.6875 229 856.7125 811.7125 230 856.7375 811.7375 231 856.7625 811.7625 232 856.7875 811.7875 233 856.8125 811.8125 234 856.8375 811.8375 235 856.8625 811.8625 236 856.8875 811.8875 237 856.9125 811.9125 238 856.9375 811.9375 239 856.9625 811.9625 240 856.9875 811.9875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

241 857.0125 812.0125 242 857.0375 812.0375 243 857.0625 812.0625 244 857.0875 812.0875 245 857.1125 812.1125 246 857.1375 812.1375 247 857.1625 812.1625 248 857.1875 812.1875 249 857.2125 812.2125 250 857.2375 812.2375 251 857.2625 812.2625 252 857.2875 812.2875 253 857.3125 812.3125 254 857.3375 812.3375 255 857.3625 812.3625 256 857.3875 812.3875 257 857.4125 812.4125 258 857.4375 812.4375 259 857.4625 812.4625 260 857.4875 812.4875 261 857.5125 812.5125 262 857.5375 812.5375 263 857.5625 812.5625 264 857.5875 812.5875 265 857.6125 812.6125 266 857.6375 812.6375 267 857.6625 812.6625 268 857.6875 812.6875 269 857.7125 812.7125 270 857.7375 812.7375 271 857.7625 812.7625 272 857.7875 812.7875 273 857.8125 812.8125 274 857.8375 812.8375 275 857.8625 812.8625 276 857.8875 812.8875 277 857.9125 812.9125 278 857.9375 812.9375 279 857.9625 812.9625 280 857.9875 812.9875 281 858.0125 813.0125 282 858.0375 813.0375 283 858.0625 813.0625 284 858.0875 813.0875 285 858.1125 813.1125 286 858.1375 813.1375 287 858.1625 813.1625 288 858.1875 813.1875

3-25

Revised January 2001

Part No. 001-7780-501

Page 52

PROGRAMMING

800 MHz Channels

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

289 858.2125 813.2125 290 858.2375 813.2375 291 858.2625 813.2625 292 858.2875 813.2875 293 858.3125 813.3125 294 858.3375 813.3375 295 858.3625 813.3625 296 858.3875 813.3875 297 858.4125 813.4125 298 858.4375 813.4375 299 858.4625 813.4625 300 858.4875 813.4875 301 858.5125 813.5125 302 858.5375 813.5375 303 858.5625 813.5625 304 858.5875 813.5875 305 858.6125 813.6125 306 858.6375 813.6375 307 858.6625 813.6625 308 858.6875 813.6875 309 858.7125 813.7125 310 858.7375 813.7375 311 858.7625 813.7625 312 858.7875 813.7875 313 858.8125 813.8125 314 858.8375 813.8375 315 858.8625 813.8625 316 858.8875 813.8875 317 858.9125 813.9125 318 858.9375 813.9375 319 858.9625 813.9625 320 858.9875 813.9875 321 859.0125 814.0125 322 859.0375 814.0375 323 859.0625 814.0625 324 859.0875 814.0875 325 859.1125 814.1125 326 859.1375 814.1375 327 859.1625 814.1625 328 859.1875 814.1875 329 859.2125 814.2125 330 859.2375 814.2375 331 859.2625 814.2625 332 859.2875 814.2875 333 859.3125 814.3125 334 859.3375 814.3375 335 859.3625 814.3625 336 859.3875 814.3875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

337 859.4125 814.4125 338 859.4375 814.4375 339 859.4625 814.4625 340 859.4875 814.4875 341 859.5125 814.5125 342 859.5375 814.5375 343 859.5625 814.5625 344 859.5875 814.5875 345 859.6125 814.6125 346 859.6375 814.6375 347 859.6625 814.6625 348 859.6875 814.6875 349 859.7125 814.7125 350 859.7375 814.7375 351 859.7625 814.7625 352 859.7875 814.7875 353 859.8125 814.8125 354 859.8375 814.8375 355 859.8625 814.8625 356 859.8875 814.8875 357 859.9125 814.9125 358 859.9375 814.9375 359 859.9625 814.9625 360 859.9875 814.9875 361 860.0125 815.0125 362 860.0375 815.0375 363 860.0625 815.0625 364 860.0875 815.0875 365 860.1125 815.1125 366 860.1375 815.1375 367 860.1625 815.1625 368 860.1875 815.1875 369 860.2125 815.2125 370 860.2375 815.2375 371 860.2625 815.2625 372 860.2875 815.2875 373 860.3125 815.3125 374 860.3375 815.3375 375 860.3625 815.3625 376 860.3875 815.3875 377 860.4125 815.4125 378 860.4375 815.4375 379 860.4625 815.4625 380 860.4875 815.4875 381 860.5125 815.5125 382 860.5375 815.5375 383 860.5625 815.5625 384 860.5875 815.5875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

385 860.6125 815.6125 386 860.6375 815.6375 387 860.6625 815.6625 388 860.6875 815.6875 389 860.7125 815.7125 390 860.7375 815.7375 391 860.7625 815.7625 392 860.7875 815.7875 393 860.8125 815.8125 394 860.8375 815.8375 395 860.8625 815.8625 396 860.8875 815.8875 397 860.9125 815.9125 398 860.9375 815.9375 399 860.9625 815.9625 400 860.9875 815.9875 401 861.0125 816.0125 402 861.0375 816.0375 403 861.0625 816.0625 404 861.0875 816.0875 405 861.1125 816.1125 406 861.1375 816.1375 407 861.1625 816.1625 408 861.1875 816.1875 409 861.2125 816.2125 410 861.2375 816.2375 411 861.2625 816.2625 412 861.2875 816.2875 413 861.3125 816.3125 414 861.3375 816.3375 415 861.3625 816.3625 416 861.3875 816.3875 417 861.4125 816.4125 418 861.4375 816.4375 419 861.4625 816.4625 420 861.4875 816.4875 421 861.5125 816.5125 422 861.5375 816.5375 423 861.5625 816.5625 424 861.5875 816.5875 425 861.6125 816.6125 426 861.6375 816.6375 427 861.6625 816.6625 428 861.6875 816.6875 429 861.7125 816.7125 430 861.7375 816.7375 431 861.7625 816.7625 432 861.7875 816.7875

Revised January 2001 Part No. 001-7780-501

3-26

Page 53

800 MHz Channels

PROGRAMMING

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

433 861.8125 816.8125 434 861.8375 816.8375 435 861.8625 816.8625 436 861.8875 816.8875 437 861.9125 816.9125 438 861.9375 816.9375 439 861.9625 816.9625 440 861.9875 816.9875 441 862.0125 817.0125 442 862.0375 817.0375 443 862.0625 817.0625 444 862.0875 817.0875 445 862.1125 817.1125 446 862.1375 817.1375 447 862.1625 817.1625 448 862.1875 817.1875 449 862.2125 817.2125 450 862.2375 817.2375 451 862.2625 817.2625 452 862.2875 817.2875 453 862.3125 817.3125 454 862.3375 817.3375 455 862.3625 817.3625 456 862.3875 817.3875 457 862.4125 817.4125 458 862.4375 817.4375 459 862.4625 817.4625 460 862.4875 817.4875 461 862.5125 817.5125 462 862.5375 817.5375 463 862.5625 817.5625 464 862.5875 817.5875 465 862.6125 817.6125 466 862.6375 817.6375 467 862.6625 817.6625 468 862.6875 817.6875 469 862.7125 817.7125 470 862.7375 817.7375 471 862.7625 817.7625 472 862.7875 817.7875 473 862.8125 817.8125 474 862.8375 817.8375 475 862.8625 817.8625 476 862.8875 817.8875 477 862.9125 817.9125 478 862.9375 817.9375 479 862.9625 817.9625 480 862.9875 817.9875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

481 863.0125 818.0125 482 863.0375 818.0375 483 863.0625 818.0625 484 863.0875 818.0875 485 863.1125 818.1125 486 863.1375 818.1375 487 863.1625 818.1625 488 863.1875 818.1875 489 863.2125 818.2125 490 863.2375 818.2375 491 863.2625 818.2625 492 863.2875 818.2875 493 863.3125 818.3125 494 863.3375 818.3375 495 863.3625 818.3625 496 863.3875 818.3875 497 863.4125 818.4125 498 863.4375 818.4375 499 863.4625 818.4625 500 863.4875 818.4875 501 863.5125 818.5125 502 863.5375 818.5375 503 863.5625 818.5625 504 863.5875 818.5875 505 863.6125 818.6125 506 863.6375 818.6375 507 863.6625 818.6625 508 863.6875 818.6875 509 863.7125 818.7125 510 863.7375 818.7375 511 863.7625 818.7625 512 863.7875 818.7875 513 863.8125 818.8125 514 863.8375 818.8375 515 863.8625 818.8625 516 863.8875 818.8875 517 863.9125 818.9125 518 863.9375 818.9375 519 863.9625 818.9625 520 863.9875 818.9875 521 864.0125 819.0125 522 864.0375 819.0375 523 864.0625 819.0625 524 864.0875 819.0875 525 864.1125 819.1125 526 864.1375 819.1375 527 864.1625 819.1625 528 864.1875 819.1875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

529 864.2125 819.2125 530 864.2375 819.2375 531 864.2625 819.2625 532 864.2875 819.2875 533 864.3125 819.3125 534 864.3375 819.3375 535 864.3625 819.3625 536 864.3875 819.3875 537 864.4125 819.4125 538 864.4375 819.4375 539 864.4625 819.4625 540 864.4875 819.4875 541 864.5125 819.5125 542 864.5375 819.5375 543 864.5625 819.5625 544 864.5875 819.5875 545 864.6125 819.6125 546 864.6375 819.6375 547 864.6625 819.6625 548 864.6875 819.6875 549 864.7125 819.7125 550 864.7375 819.7375 551 864.7625 819.7625 552 864.7875 819.7875 553 864.8125 819.8125 554 864.8375 819.8375 555 864.8625 819.8625 556 864.8875 819.8875 557 864.9125 819.9125 558 864.9375 819.9375 559 864.9625 819.9625 560 864.9875 819.9875 561 865.0125 820.0125 562 865.0375 820.0375 563 865.0625 820.0625 564 865.0875 820.0875 565 865.1125 820.1125 566 865.1375 820.1375 567 865.1625 820.1625 568 865.1875 820.1875 569 865.2125 820.2125 570 865.2375 820.2375 571 865.2625 820.2625 572 865.2875 820.2875 573 865.3125 820.3125 574 865.3375 820.3375 575 865.3625 820.3625 576 865.3875 820.3875

3-27

Revised January 2001

Part No. 001-7780-501

Page 54

PROGRAMMING

800 MHz Channels

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

577 865.4125 820.4125 578 865.4375 820.4375 579 865.4625 820.4625 580 865.4875 820.4875 581 865.5125 820.5125 582 865.5375 820.5375 583 865.5625 820.5625 584 865.5875 820.5875 585 865.6125 820.6125 586 865.6375 820.6375 587 865.6625 820.6625 588 865.6875 820.6875 589 865.7125 820.7125 590 865.7375 820.7375 591 865.7625 820.7625 592 865.7875 820.7875 593 865.8125 820.8125 594 865.8375 820.8375 595 865.8625 820.8625 596 865.8875 820.8875 597 865.9125 820.9125 598 865.9375 820.9375 599 865.9625 820.9625 600 865.9875 820.9875

- 866.0000 821.0000

601 866.0125 821.0125

- 866.0250 821.0250 602 866.0375 821.0375 603 866.0500 821.0500 604 866.0625 821.0625 605 866.0750 821.0750 606 866.0875 821.0875 607 866.1000 821.1000 608 866.1125 821.1125 609 866.1250 821.1250 610 866.1375 821.1375 611 866.1500 821.1500 612 866.1625 821.1625 613 866.1750 821.1750 614 866.1875 821.1875 615 866.2000 821.2000 616 866.2125 821.2125 617 866.2250 821.2250 618 866.2375 821.2375 619 866.2500 821.2500 620 866.2625 821.2625 621 866.2750 821.2750 622 866.2875 821.2875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

623 866.3000 821.3000 624 866.3125 821.3125 625 866.3250 821.3250 626 866.3375 821.3375 627 866.3500 821.3500 628 866.3625 821.3625 629 866.3750 821.3750 630 866.3875 821.3875 631 866.4000 821.4000 632 866.4125 821.4125 633 866.4250 821.4250 634 866.4375 821.4375 635 866.4500 821.4500 636 866.4625 821.4625 637 866.4750 821.4750 638 866.4875 821.4875

- 866.5000 821.5000

639 866.5125 821.5125

- 866.5250 821.5250 640 866.5375 821.5375 641 866.5500 821.5500 642 866.5625 821.5625 643 866.5750 821.5750 644 866.5875 821.5875 645 866.6000 821.6000 646 866.6125 821.6125 647 866.6250 821.6250 648 866.6375 821.6375 649 866.6500 821.6500 650 866.6625 821.6625 651 866.6750 821.6750 652 866.6875 821.6875 653 866.7000 821.7000 654 866.7125 821.7125 655 866.7250 821.7250 656 866.7375 821.7375 657 866.7500 821.7500 658 866.7625 821.7625 659 866.7750 821.7750 660 866.7875 821.7875 661 866.8000 821.8000 662 866.8125 821.8125 663 866.8250 821.8250 664 866.8375 821.8375 665 866.8500 821.8500 666 866.8625 821.8625 667 866.8750 821.8750 668 866.8875 821.8875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

669 866.9000 821.9000 670 866.9125 821.9125 671 866.9250 821.9250 672 866.9375 821.9375 673 866.9500 821.9500 674 866.9625 821.9625 675 866.9750 821.9750 676 866.9875 821.9875

- 867.0000 822.0000

677 867.0125 822.0125

- 867.0250 822.0250 678 867.0375 822.0375 679 867.0500 822.0500 680 867.0625 822.0625 681 867.0750 822.0750 682 867.0875 822.0875 683 867.1000 822.1000 684 867.1125 822.1125 685 867.1250 822.1250 686 867.1375 822.1375 687 867.1500 822.1500 688 867.1625 822.1625 689 867.1750 822.1750 690 867.1875 822.1875 691 867.2000 822.2000 692 867.2125 822.2125 693 867.2250 822.2250 694 867.2375 822.2375 695 867.2500 822.2500 696 867.2625 822.2625 697 867.2750 822.2750 698 867.2875 822.2875 699 867.3000 822.3000 700 867.3125 822.3125 701 867.3250 822.3250 702 867.3375 822.3375 703 867.3500 822.3500 704 867.3625 822.3625 705 867.3750 822.3750 706 867.3875 822.3875 707 867.4000 822.4000 708 867.4125 822.4125 709 867.4250 822.4250 710 867.4375 822.4375 711 867.4500 822.4500 712 867.4625 822.4625 713 867.4750 822.4750 714 867.4875 822.4875

Revised January 2001 Part No. 001-7780-501

3-28

Page 55

800 MHz Channels

PROGRAMMING

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

- 867.5000 822.5000

715 867.5125 822.5125

- 867.5250 822.5250 716 867.5375 822.5375 717 867.5500 822.5500 718 867.5625 822.5625 719 867.5750 822.5750 720 867.5875 822.5875 721 867.6000 822.6000 722 867.6125 822.6125 723 867.6250 822.6250 724 867.6375 822.6375 725 867.6500 822.6500 726 867.6625 822.6625 727 867.6750 822.6750 728 867.6875 822.6875 729 867.7000 822.7000 730 867.7125 822.7125 731 867.7250 822.7250 732 867.7375 822.7375 733 867.7500 822.7500 734 867.7625 822.7625 735 867.7750 822.7750 736 867.7875 822.7875 737 867.8000 822.8000 738 867.8125 822.8125 739 867.8250 822.8250 740 867.8375 822.8375 741 867.8500 822.8500 742 867.8625 822.8625 743 867.8750 822.8750 744 867.8875 822.8875 745 867.9000 822.9000 746 867.9125 822.9125 747 867.9250 822.9250 748 867.9375 822.9375 749 867.9500 822.9500 750 867.9625 822.9625 751 867.9750 822.9750 752 867.9875 822.9875

- 868.0000 823.0000 753 868.0125 823.0125

- 868.0250 823.0250 754 868.0375 823.0375 755 868.0500 823.0500 756 868.0625 823.0625 757 868.0750 823.0750 758 868.0875 823.0875

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

759 868.1000 823.1000 760 868.1125 823.1125 761 868.1250 823.1250 762 868.1375 823.1375 763 868.1500 823.1500 764 868.1625 823.1625 765 868.1750 823.1750 766 868.1875 823.1875 767 868.2000 823.2000 768 868.2125 823.2125 769 868.2250 823.2250 770 868.2375 823.2375 771 868.2500 823.2500 772 868.2625 823.2625 773 868.2750 823.2750 774 868.2875 823.2875 775 868.3000 823.3000 776 868.3125 823.3125 777 868.3250 823.3250 778 868.3375 823.3375 779 868.3500 823.3500 780 868.3625 823.3625 781 868.3750 823.3750 782 868.3875 823.3875 783 868.4000 823.4000 784 868.4125 823.4125 785 868.4250 823.4250 786 868.4375 823.4375 787 868.4500 823.4500 788 868.4625 823.4625 789 868.4750 823.4750 790 868.4875 823.4875 791 868.5000 823.5000 792 868.5125 823.5125 793 868.5250 823.5250 794 868.5375 823.5375 795 868.5500 823.5500 796 868.5625 823.5625 797 868.5750 823.5750 798 868.5875 823.5875 799 868.6000 823.6000 800 868.6125 823.6125 801 868.6250 823.6250 802 868.6375 823.6375 803 868.6500 823.6500 804 868.6625 823.6625 805 868.6750 823.6750 806 868.6875 823.6875

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

807 868.7000 823.7000 808 868.7125 823.7125 809 868.7250 823.7250 810 868.7375 823.7375

811 868.7500 823.7500 812 868.7625 823.7625 813 868.7750 823.7750 814 868.7875 823.7875 815 868.8000 823.8000 816 868.8125 823.8125 817 868.8250 823.8250 818 868.8375 823.8375 819 868.8500 823.8500 820 868.8625 823.8625 821 868.8750 823.8750 822 868.8875 823.8875 823 868.9000 823.9000 824 868.9125 823.9125 825 868.9250 823.9250 826 868.9375 823.9375 827 868.9500 823.9500 828 868.9625 823.9625 829 868.9750 823.9750 830 868.9875 823.9875

- 869.0000 824.0000

- 869.0125 824.0125

- 869.0250 824.0250

- 869.0375 824.0375

- 869.0500 824.0500

- 869.0625 824.0625

- 869.0750 824.0750

- 869.0875 824.0875

- 869.1000 824.1000

- 869.1125 824.1125

- 869.1250 824.1250

- 869.1375 824.1375

- 869.1500 824.1500

- 869.1625 824.1625

- 869.1750 824.1750

- 869.1875 824.1875

- 869.2000 824.2000

- 869.2125 824.2125

- 869.2250 824.2250

- 869.2375 824.2375

- 869.2500 824.2500

- 869.2625 824.2625

- 869.2750 824.2750

- 869.2875 824.2875

3-29

Revised January 2001

Part No. 001-7780-501

Page 56

PROGRAMMING

800 MHz Channels

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

- 869.3000 824.3000

- 869.3125 824.3125

- 869.3250 824.3250

- 869.3375 824.3375

- 869.3500 824.3500

- 869.3625 824.3625

- 869.3750 824.3750

- 869.3875 824.3875

- 869.4000 824.4000

- 869.4125 824.4125

- 869.4250 824.4250

- 869.4375 824.4375

- 869.4500 824.4500

- 869.4625 824.4625

- 869.4750 824.4750

- 869.4875 824.4875

- 869.5000 824.5000

- 869.5125 824.5125

- 869.5250 824.5250

FCC Chan.

No.

Mobile Rx

Freq.

Mobile Tx

Freq

- 869.5375 824.5375

- 869.5500 824.5500

- 869.5625 824.5625

- 869.5750 824.5750

- 869.5875 824.5875

- 869.6000 824.6000

- 869.6125 824.6125

- 869.6250 824.6250

- 869.6375 824.6375

- 869.6500 824.6500

- 869.6625 824.6625

- 869.6750 824.6750

- 869.6875 824.6875

- 869.7000 824.7000

- 869.7125 824.7125

- 869.7250 824.7250

- 869.7375 824.7375

- 869.7500 824.7500

- 869.7625 824.7625

FCC Chan.

No.

Mobile Rx

Freq

Mobile Tx

Freq

- 869.7750 824.7750

- 869.7875 824.7875

- 869.8000 824.8000

- 869.8125 824.8125

- 869.8250 824.8250

- 869.8375 824.8375

- 869.8500 824.8500

- 869.8625 824.8625

- 869.8750 824.8750

- 869.8875 824.8875

- 869.9000 824.9000

- 869.9125 824.9125

- 869.9250 824.9250

- 869.9375 824.9375

- 869.9500 824.9500

- 869.9625 824.9625

- 869.9750 824.9750

- 869.9875 824.9875

Revised January 2001 Part No. 001-7780-501

3-30

Page 57

ALIGNMENT AND PERFORMANCE TESTS

SECTION 4 ALIGNMENT AND PERFORMANCE TESTS

Remote Programming Interface (R PI)

Part No. 023-9800-000

4.7-ohm

Speaker Load

13.6 VDC

Power Supply

Ign Sense (Optional)

Wattmeter

PC-Compatible

Computer

Figure 4-1 Alignment Setup

4.1 GENERAL

4.1.1 INTRODUCTION

The alignment procedure des cribed in this secti on should be performed if repairs are made that could affect the factory alignment. In addition, before a transceive r is initially placed in service, the performance tests described in Section 4.8 should be performed.

To perform the alignment described in this section, special PCTune software (see Table 1-1) and the same basic computer setup used for programming is required. This equipment is shown above and also described in Section 3.1. Remote Programming Interface (RPI), Part No. 023-9800-000, or others can be used (except 023-5300-000). The speaker and microphone audio jacks on the 9800 RPI are not required in this application.

50-ohm

Load

Signal Generator/

Comm. Monitor

With 800 MHz models, only thr ee or four adjus tments are made manually and the others are made digitally using the PCTune software. The manual adjustments tune th e IF and high p ower PA, and set the TCXO frequency. If they do not need to be reset, the transceiver can be tuned without removing the top or bottom covers.

This transceiver does not have a spe cial test mode that is selected. The PCTune software automatically selects the frequencies and other test conditions that are required to perform the alignment. If the transceiver must be controlled manually to perform such things as testing or troubleshooting, program temporary conventional channels.

4.1.2 TEST SETUP

Connect the test setup shown in Figure 4-1. Additional information follows on equipment in this setup.

4-1

Revised January 2001

Part No. 001-9800-501

Page 58

ALIGNMENT AND PERFORMANCE TESTS

RF Signal Generator - When connecting the generator to the antenna jack, use at least a 6 dB pad between the generator and transceiver. This protects the generator if the transmitter is accidentally keyed and also ensures that a 50-ohm load exists. The input levels listed in the PCTune screens are at the antenna jack, so increase the generator output accordingly.

Power Source - Typical current when transmitting is 7 amperes with 15-watt models, and 11 amperes with 30-watt models. Therefore, a power supply capable of producing that current at 13.6 volts is required.

Wattmeter/Load - The wattmeter and dummy load must measure and dissipate up to approximately 30 watts. For accurate power output measurement at 800 MHz, use a minimum number of connectors with a Teflon or better dielectric. If coaxial cable is used, it should be a minimum length of a low-loss type.

Speaker Load - The speaker load is connected to the 1/8” phone jack on the back of the transceiver.

Computer and RPI - The RPI is connected to the computer and transceiver as described in Section

3.1.4. RPI, Part No. 023-9800-000 or other RPIs (except 023-5300-000) can be used as described in the preceding section.

2. Insert the disk containing the PCTune software in drive A: (or B:).

3. From the Windows 95 taskbar, choose RUN and open SETUP .EXE on drive A: (or B:) . Alternatively , use File Explorer and double click SETUP.EXE.

From the Windows 3.1 Program Manager, choose FILE > RUN and select the SETUP.EXE file on drive A: (or B:).

4. Follow the instructions on the scr een. The program is automatically loaded on the hard drive and startup shortcuts or groups are created.

Starting PCTune

From Windows 95 - Select Start in the taskbar, then Programs > PCTune > PCTune.

From Windows 3.1 - From the Program Manager, open the PCTune group and then double click the PCTune icon.

Exiting PCTune

Select File > Exit or click the “X” button on the

right end of the title bar.

4.1.3 TUNE SOFTWARE

General

The PCTune software is a Windows®-based program. Minimum ments are as follows:

• Windows

software and hardware re quire-

95 or 3.1

• 386SX or faster microprocessor

• 4 megabytes of RAM

• 3 megabytes free space available on hard drive

• An available serial port

Software Installation

Proceed as follows to install this software:

1. Close all applications that are currently running

(other than Windows).

4.1.4 PRELIMINARY SETUP

1. With transceiver power turned off, connect the RPI to an unused serial port of the computer. Then connect the RPI to the micro phone ja ck of the tr ansceiver (see Section 3.1.4).

2. Start the PCTune program as described in the preceding section. If required, select the serial port being used by selecting Options > Set Comm Port.

3. Turn transceiver power on and the green indicator on the RPI should li ght. Move the sele ctor switch on the RPI to the other position if this indicator is amber.

4. Follow the instructions on the screen to display the main screen shown in Figure 4-2. Select Tuning > Complete Tuning to automatically step through a complete alignment or Tuning > Partial Tuning to manually select each adjustment.

Revised January 2001 Part No. 001-9800-501

4-2

Page 59

ALIGNMENT AND PERFORMANCE TESTS

Figure 4-2 PCTune Main Screen

5. The computer then attempts to establish communication with the transceiver. When communication is established, “Com Link Esta blished” is displayed in the “Status” box and “TUNING” is indicated in the transceiver display. Instructions are then displayed in the “Instructions” box on how to proceed with each adjustment.

4.1.5 READING CURRENT SETTINGS

To read and display the settings currently programmed in a transceiver, select Tuning > Display Tune Parameters from the Menu bar. The screen in Figure 4-3 is then displayed. The following functions can be performed from this screen:

• To read the settings in the transceiver from this

screen, click the “Read” button.

• T o write the settings in this screen to the transceiver,

click the “Write” bu tton.

• T o set all parameters in this scr een to a defaul t level,

click the “Set Defaults” button.

• T o set onl y the RSSI levels to the defaul t level, cl ick

the “Set RSSI Defaults Only” button.

Figure 4-3 Tune Parameters Scree n

4.2 TRANSMIT POWER OUTPUT

1. Connect a wattmeter and 50-ohm load to the

antenna jack as shown in Figure 4-1. Manually or automatically select “Tx Power” and follow the onscreen inst ructions.

Revised January 2001

4-3

Part No. 001-9800-501

Page 60

ALIGNMENT AND PERFORMANCE TESTS

2. With high power (30W) models only, C656 on the PA board is adjusted for minimum current. Remove the bottom cover and adjust C656 as required.

3. Adjust for the displayed power output at various frequencies across t he ba nd. A hi gh and low power output level is set by this function. The allowable power output range for each model is as follows:

Mid Power (15W) Models - 2-15 watts High Power (30W) Models - 10-30 watts

4.3 FREQUENCY SET/VCO CHECK

1. Connect a 50-ohm load to the antenna jack and monitor the transmit signal with a co mmunication monitor.

2. Select the Frequency Set/VCO Check function. Set the communication monitor to the displayed frequency and click the “OK” button to key the transmitter and begin the adjustment process.

2. Set the communication monitor for the displayed frequency and then click “OK” to tr ansmit a signal modulated w ith an 80 Hz tone. Enter the measured deviation (in hertz) in the displayed box and click “OK”.

3. Continue following the scr een instruct ions to adjust the 3 kHz tone deviation. The + and – buttons are clicked to set the deviation to the indicated level. The 1 kHz tone is then adjusted.

4. The preceding 3 kHz and 1 kHz tone adjustments are then repeated on several frequencies across the band. After the last adjustment is made, the transmitter unkeys and the settings are stored.

Ref Osc Freq.

R848/C836

J201

Pin 20

Pin 19

3. If adjustment is required, remove the top cover of the transceiver to access the RF board. Then manually adjust the variable capacitor in reference oscillator U806 for the displayed frequency ±100 Hz (see Figure 4-4). This also sets the receive frequency.

4. The VCO control line v oltage can be checked for the indicated readings at the junction of R848 and C836. If it is not within the indicated limits, there may be a synthesizer problem or the VCO may be defective. The control v oltage is not adjustable.

4.4 TRANSMIT MODULATION

Transmit modulation is set by balancing the modulation produced by 80 Hz and 3 kHz tones and then setting modulation limiting using a 1 kHz tone. All of these tones are internally generated by the transceiver, so no external audio generator is required. Proceed as follows:

1. Connect a 50-ohm load to the antenna jack and

monitor the transmit signal with a co mmunication monitor. Manually or automatically select “Tx Modulation”.

L218

L215

L213

Figure 4-4 Alignment Points Diagram

Revised January 2001 Part No. 001-9800-501

4-4

Page 61

ALIGNMENT AND PERFORMANCE TESTS

4.5 RECEIVER IF ALIGNMENT AND CHECK

1. If required, remove the top cover of the transceiver to access the RF board. Manually or automatically select “Receiver IF Alignment”.

2. Connect an RF signal generator to the antenna jack using a 6 dB or g reater pad . Set the ge nerator out put for the displayed frequency, modulated with 1 kHz at 3 kHz deviation.

3. Connect the DC voltmeter to J201, pin 20

(see Figure 4-4). Set the generator output level for –47 dBm (1.0 mV) at the antenna jack. and manually adjust L218 for a meter reading of 2.9 V ±0.1 V.

4. Set the generator out put le vel for –80 dBm (22 µV) at the antenna jack. Connect a SINAD meter to the speaker jack on the back of the transceiver and adjust the volume level to approximately 1/3 of the maximum level. Click “OK” and manually adjust L213 and L215 for best SINAD.

1. Manually or automatically select “RSSI”. Connect an RF signal generator to the an tenna jack using a 6 dB or greater pad and set it for the displayed frequency and output level.

2. Follow the instructions displayed on the screen.

4.8 PERFORMANCE TESTING

Performance testing can be accomplished by programming temporary conventional channels and then checking receiver and transmitter operation on those channels. Ch annels s hould be programmed at the low, mid, and high ends of the operating band.

The PCTune software described in the preceding information can also be used for basic performance testing. Transmitter power output can be checked as described in Section 4.2, and receiver sensitivity can be checked as described in Section 4.5.

5. Manually or auto matically select “Receiver Check”. Follow the instructions to check SINAD sensitivi ty on the low , mid, and high chann els indica ted. Click the Wide Band/Narrow Band button to switch the selected bandwidth. Use 3 kHz deviation for wide band channels and 1.5 kHz deviation for narrow band channels.

4.6 SQUELCH ADJUSTMENT

1. Connect an RF signal generator to the antenna jack using a 6 dB or gre at er pad. Also connect a SINAD meter to the speaker jack and adjust the volume to 1/3 maximum if required.

2. Manually or automatica lly select “Squel ch”. Set the signal generator for the indicated frequency and modulation and adjust the output level for the indicated SINAD level.

3. Follow t he instructions on the screen to adjust the wide and narrow band squelch level.

Receiver and transmitter specifications you may

want to check are as follows:

Receiver Sp ecificatio ns

12 dB SINAD Sensitivity - 0.35 µV maximum Audio Power Output - 5 watts (w/external 4.7-ohm

load)

Audio Distortion - Less than 5%

Transmitter Specifications

RF Power Output:

15-Watt Models - 2-15 watts 30-Watt Models - 10-30 watts

Wideband Devi at ion:

Voice Only - 3.0 kHz ±100 Hz Data Only -1000 Hz ±100 Hz Total Voice and Data - 4.7 kHz maximum

4.7 RSSI ADJUSTMENT

This adjustm ent calibr ates the RSS I signal level.

Proceed as follows:

4-5

Narrow Band Deviation:

Voice Only - 1.2 kHz ±100 Hz Data Only - 800 Hz ±100 Hz Total Voice and Data - 2.3 kHz maximum

Revised January 2001

Part No. 001-9800-501

Page 62

DSP BOARD SERVICING INFORMATION

SECTION 5 DSP BOARD SERVICING INFORMATION

98xx Audio/Logic Board Part Changes

Ref No. Description Part No.

ADDED PARTS

J 310 10-pin single in-line header 515-7100-010 J 311 10-pin single in-line header 515-7100-010

DELETED PARTS

Location

C 335 J302, pin 9 510-2625-479 R 354 U301D, pin 14 output jumper 569-0115-001 R 383 U303D, pin 14 output jumper 569-0115-001 U 102 U101, pin 32 (4K x 8 EEPROM) 544-5001-416

98xx RF Board Part Change

Ref No. Description Part No.

J201 20-pin connector, .82” pin male 515-7103-060

DSP Board Parts List

Ref No. Description Part No.

C 001 100 nF X7R ±10% 50V cer smd 510-3605-104 C 002 100 nF X7R ±10% 50V cer smd 510-3605-104 C 003 100 nF X7R ±10% 50V cer smd 510-3605-104 C 004 10 µF low ESR tantalum 510-2610-100 C 005 10 µF low ESR tantalum 510-2610-100 C 006 100 nF X7R ±10% 50V cer smd 510-3605-104 C 007 .001 µF NPO ±5% cer smd 510-3601-102 C 008 4.7 µF ±10% 50V tantalum 510-2622-479 C 009 390 pF ±5% NPO 50V cer smd 510-3601-391 C 010 390 pF ±5% NPO 50V cer smd 510-3601-391 C 011 4.7 µF ±10% 50V tantalum 510-2622-479 C 012 390 pF ±5% NPO 50V cer smd 510-3601-391 C 013 390 pF ±5% NPO 50V cer smd 510-3601-391 C 014 4.7 µF ±10% 50V tantalum 510-2622-479 C 015 100 nF X7R ±10% 50V cer smd 510-3605-104 C 016 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 017 10 µF low ESR tantalum 510-2610-100 C 018 10 µF low ESR tantalum 510-2610-100 C 019 100 nF X7R ±10% 50V cer smd 510-3605-104 C 020 100 nF X7R ±10% 50V cer smd 510-3605-104 C 021 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 022 100 nF X7R ±10% 50V cer smd 510-3605-104

Ref No. Description Part No.

C 023 100 nF X7R ±10% 50V cer smd 510-3605-104 C 024 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 025 100 nF X7R ±10% 50V cer smd 510-3605-104 C 026 100 nF X7R ±10% 50V cer smd 510-3605-104 C 027 100 µF 16V tantalum smd 510-2616-101 C 028 100 µF 16V tantalum smd 510-2616-101 C 029 100 µF 16V tantalum smd 510-2616-101 C 030 10 µF low ESR tantalum 510-2610-100 C 031 100 nF X7R ±10% 50V cer smd 510-3605-104 C 032 100 nF X7R ±10% 50V cer smd 510-3675-104 C 033 100 nF X7R ±10% 50V cer smd 510-3605-104 C 034 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 035 100 nF X7R ±10% 50V cer smd 510-3605-104 C 036 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 037 100 nF X7R ±10% 50V cer smd 510-3605-104 C 038 100 nF X7R ±10% 50V cer smd 510-3605-104 C 039 100 nF X7R ±10% 50V cer smd 510-3605-104 C 041 470 pF X7R ±10% 50V cer smd 510-3605-471 C 042 470 pF X7R ±10% 50V cer smd 510-3605-471 C 044 100 nF X7R ±10% 50V cer smd 510-3605-104 C 045 .001 µF NPO ±5% 50V cer smd 510-3601-102 C 046 100 nF X7R ±10% 50V cer smd 510-3605-104 C 047 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 048 100 nF X7R ±10% 50V cer smd 510-3605-104 C 049 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 050 100 nF X7R ±10% 50V cer smd 510-3605-104 C 051 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 052 100 nF X7R ±10% 50V cer smd 510-3605-104 C 053 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 054 100 nF X7R ±10% 50V cer smd 510-3605-104 C 055 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 056 100 nF X7R ±10% 50V cer smd 510-3605-104 C 057 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 058 100 nF X7R ±10% 50V cer smd 510-3605-104 C 059 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 060 100 nF X7R ±10% 50V cer smd 510-3605-104 C 061 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 062 100 nF X7R ±10% 50V cer smd 510-3605-104 C 063 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 064 100 nF X7R ±10% 50V cer smd 510-3605-104 C 065 .001 µF NPO ±5% 50V cer smd 510 -3601-102 C 066 100 nF X7R ±10% 50V cer smd 510-3605-104 C 067 .001 µF NPO ±5% 50V cer smd 510-3601-102

5-1

Revised January 2001

Part No. 001-9800-501

Page 63

DSP BOARD SERVICING INFORMATION

DSP BOARD PARTS LIST (CONT’D)

Ref No. Description Part No.

F 001 Fuse, 0.6A smd 534-5001-002

D 001 Dual switch-com cathode 523-1504-022

MP 182 Washer, insulated #6 fiber 596-4406-010 MP 185 0.197 swage mount 013-1188-053

PCB001 PC board, SN/SZ DSP (rev 7) 035-1825-180

PL 001 4-pin angle header, 1” center 515-9035-004 PL 002 10-pin single inline header 515-7100-010 PL 003 10-pin single inline header 515-7100-010

R 001 2.0k ohm ±5% 1/8W smd 569-0105-202 R 002 4.7k ohm ±5% 1/8W smd

(revised versions) 0 ohm jumper

(unrevised versions) R 003 270k ohm ±5% 1/8W smd 569-0105-274 R 004 82k ohm ±5% cer smd 569-0105-823 R 005 160k ohm ±5% cer smd 569-0105-164 R 006 270k ohm ±5% 1/8W smd 569-0105-274 R 007 0.5 ohm ±5% 1W smd R 008 6.8k ohm ±5% 1/8W smd 569-0105-682 R 009 15k ohm ±5% 1/8W smd 569-0105-153 R 010 18k ohm ±5% 1/8W smd 569-0105-183 R 011 1.8k ohm ±5% 1/8W smd 569-0105-182 R 012 15k ohm ±5% 1/8W smd 569-0105-153 R 013 30k ohm ±5% 1/8W smd 569-0105-303 R 014 30k ohm ±5% 1/8W smd 569-0105-303 R 015 10k ohm ±5% 1/8W smd 569-0105-103 R 016 30k ohm ±5% 1/8W smd 569-0105-303 R 017 30k ohm ±5% 1/8W smd 569-0105-303 R 018 18k ohm ±5% 1/8W smd 569-0105-183 R 019 2.0k ohm ±5% 1/8W smd 569-0105-202 R 020 10k ohm ±5% 1/8W smd 569-0105-103 R 021 10k ohm ±5% 1/8W smd 569-0105-103

569-0105-472

569-0105-001

569-0175-05A

Ref No. Description Part No.

R 022 10k ohm ±5% 1/8W smd 569-0105-103 R 023 10k ohm ±5% 1/8W smd 569-0105-103 R 024 10k ohm ±5% 1/8W smd 569-0105-103 R 025 10k ohm ±5% 1/8W smd 569-0105-103 R 026 2.0k ohm ±5% 1/8W smd 569-0105-202 R 028 2.0k ohm ±5% 1/8W smd 569-0105-202 R 029 100 ohm ±5% 1/8W smd 569-0105-101 R 030 270k ohm ±5% 1/8W smd 569-0105-274 R 031 10k ohm ±5% 1/8W smd 569-0105-103 R 032 10k ohm ±5% 1/8W smd 569-0105-103 R 033 10k ohm ±5% 1/8W smd 569-0105-103 R 034 10k ohm ±5% 1/8W smd 569-0105-103 R 035 10k ohm ±5% 1/8W smd 569-0105-103

SK 002 Crystal socket 515-5006-018 SK 003 Crystal socket 515-5006-018 SK 004 Crystal socket 515-5006-018 SK 005 Crystal socket 515-5006-018

U 001 Fixed point DSP TMS320VC5402 544-5003-121 U 002 Audio CODEC PCM3002 544-3016-055 U 003 64K x 163V SRAM MCM6323A 544-5001-130 U 004 256K x 16 FLASH AM29LV800 544-9050-020 U 005 Voltage regulator TPS7201QD 544-2003-153 U 006 Voltage reg 3.3V TPS7333QD 544-1020-009 U 007 32K x 8 EEPROM AT24C256W 544-1020-256 U 008 Op amp, quad MC3303 544-2020-008 U 009 Hex inverter SN74LVC04A 544-3774-020 U 010 Hex inverter SN74LVC04A 544-3774-020 U 011 Voltage reg 3.3V TPS7333QD 544-1020-009 U 012 Bus xcvr, octal SN74LVCC3245 544-1010-248 U 013 Bus xcvr, octal SN74LVCC3245 544-1010-248 U 015 Voltage r egulator, 5V TL750M 544-1020-750 U 016 2 input OR quad 74HC32 544-3766-032

Y 001 Crystal, 4.096 MHz smd 521-3060-061

Revised January 2001 Part No. 001-9800-501

5-2

Page 64

DSP BOARD SERVICING INFORMATION

4 3

PL1

SK4

SK5

DSP Board

PL2 PL3

SK3 SK2

Audio/Logic

Board

DSP BOARD CONNECTIONS T O AUDIO/LOGIC BOARD

5-3

Revised January 2001

Part No. 001-9800-501

Page 65

DSP BOARD SERVICING INFORMATION

109

C66

144

108

C39

C44

122

C27

C20

U15

C21

C25

R25

U10

C38

C53

C52

C64

C65

C55 C54

C67

C30

+ 5

C57

C45

C56

PL2

C63

R33

PL3

C62

C26

C50

R34

R15

C51

C47 C46

R32

C32

C31

112

R36

R11

C24

R21

C23

R12

R20

C60

C61

C48

112

C59 C49

C58

R31

R29

U13

U11

R10

C12

R23 C22

C19

R30

R28

R35

R24

R22

R38

R16

R14

C10

C41

U12

C40

C37

U16

C42

C16 C15

C33

C34

R13

R18

R17

PL004

SK4

SK3

SK2

C13

A10

C35

C36

R26

R37

R19

PL1

C17

1 2

A20

SK5

A11

C18

C11

C14

REVISED DSP BOARD COMPONENT LAYOUT

Revised January 2001 Part No. 001-9800-501

5-4

Page 66

Revised January 2001

Part No. 001-9800-501

5-5

+ 5V

U12

SN74LVCC3245

VCCA DIR A1 A2 A3 A4 A5 A6 A7 A8 GND1 GND2

1 2 3 4 5 6 7 8

9 10 11 12

SCK

MOSI

VCCB

NC OE B1 B2 B3 B4 B5 B6 B7 B8

GND3

3.3VD

C22

0.1

+ 5V

U13

SN74LVCC3245

VCCA DIR A1 A2 A3 A4 A5 A6 A7 A8 GND1 GND2

VCCB

NC OE B1 B2 B3 B4 B5 B6 B7 B8

GND3

3.3VD

C32

0.1

C31

0.1 U16A

7432

1 2 3 4

NC1 NC2 VSS1 DVDD1 A10 HD7 A11 A12 A13 A14 A15 NC3 HAS VSS2 NC4 CVDD1 HCS HR/W Ready PS DS IS R/W MSTRB IOSTRB MSC XF HOLDA IAQ HOLD BIO MP/MC DVDD2 VSS3 NC5 NC6

NC7

MC8

HCNTL0

VSS4

BCLKR0

BCLKR1

BFSR0

BFSR1

BDR0

HCNTL1

BDR1

BCKLX0

BCLKX1

VSS5

HINT/TOUT1

CVDD2

BFSX0

BFSX1

HRDY

DVDD3

VSS6

HD0

BDX0

BDX1

ACK

HBIL

NMI

INT0

INT1

INT2

INT3

CVDD3

HD1

VSS7

NC9

NC10

NC11

NC12

DBDD4

VSS0

CLKMD1

CLKMD2

CLKMD3

NC13

HD2

TOUT0

EMU0

EMU1/OFF

TD0

TD1

TRST

TCK

TMS

NC14

CVDD4

HPIENA

VSS9

CLKOUT

HD3

X2/CLKIN

A16

VSS10

A17

A18

NC18

NC17

CVDD6

A9A8A7A6A5

HD6

A3A2A1

DVDD6

HDS2

VSS12

HDS1

NC16

CVDD5

HD5

D15

D14

D13

HD4

D12

D11

D10

D9D8D7

DVDD5

VSS11

NC15

A19

VCC1 VCC2 VINR VREFL VREFR VINL RST ML SYSCLK LRCIN BCKIN DOUT

DGND

VDD

DIN

ZFLG

MD MC

VOUTL

VOUTR

VCOM

GND1

GND2

VCC3

1 2 3 4 5 6 7 8

9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

PCM3002

3.3VD

1.8V

R24 10k

R23 10k

R21 10k

R20 10k

3.3VD

R31 10k

R32

10k

R33

10k

1.8V

3.3VD

1.8V

1 2 3 4 5 6 7 8 9

10 12

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

3738394041424344454647484950515253545556575859606162636465666768697071

108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73

143

142

141

140

139

138

137

136

135

134

133

132

131

130

129

128

127

126

125

124

123

122

121

120

119

118

117

116

115

114

113

112

111

110

109

144

MISO

MOSI

SCK

MISO

1 2 3 4 5 6 7 8

9 10 11 12

A118 A117

A116

D100

D101

D102

D103

D104

D105

D106

D107

D108

D109

D110

D111

D112

D113

D114

D115

3.3VD

A110 A111

A112 A113 A114 A115

A109

A108

A107

A106

A105

A104

A103

A102

A101

3.3VD

A100

C33

0.1

C34

0.001

3.3VD

C35

0.1

C36

0.001

3.3VA

C14

4.7

C11

4.7

C19

0.1

VREF

3.3VA

C37

0.1

1 9 11 2 3 7 14 13 6 5 4 8 10 12

3.3VD

R34 10k

R35 10k

PL004

R15 10k

TMS320VC5402

DIGITAL SIGNAL PROCESSOR

(DSP)

Serial Data

Serial Clock

VIAS TO AUDIO/LOGIC

BOARD J302

A11 A12 A13 SK5 A15 A16 A17 A18 A19 A20

SK2 SK3 A3 SK4

A5 A6 A7 A8 A9

A10

6 5 4 3 2 1

15 16 17 18 19 20

Receive Audio Transmit Audio

To J302, Pin:

1 2 3 4

PL1

Wire Harness To

Audio/Logic Board

From U102, Pin 1 Wire-Out Not Connected To U102, Pin 2 Wire-Out From Latch U112, Pin 14 (Output E)

To Audio/Logic Board

IN 2

–

U8B

MC3303

VREF

R16

30k

C12

390pF

R28

Rx Audio Amp

OUTPUT B

PL3 1 9 2 5 6 3 4 8 10

R36

0 ohm

–

U8D

MC3303

VREF

R14 30k

C10

390pF

R9 15k

R19

–

U8D

MC3303

VREF

R13

30k

390pF

R12 15k

R26

IN 3

OUTPUT A

Rx In

Tx In

W301 W309 W302 W305 W306 W303 W304 W308 W310

W307

Rx Audio Amp

Tx Audio Amp

Option 1:

PL2

–

U8A

MC3303

VREF

R17 30k

C13

390pF

R18 18k

R1 2k

Tx Audio Amp

R37

0 ohm

R10

18k

R38 18k

C40

0.1

2 3

5 7 8

Source

Rx Audio Out

Tx Audio Out

Option 2:

W311 W319 W312 W313 W314 W315 W317 W318 W320

Source

C25

0.1

C27 100

+5V

Source

IN Out

Gnd

U15

TL750M

+5V REGULATOR

3.3VD (DIGITAL) REGULATOR

1 2 3 4

0.1

C30 10

Gnd EN In 1 In 2

Sense

Out 2 Out 1

3.3VD Source

270k

TPS7333QD

+1.8V REGULATOR

0.1

Gnd EN In 1 In 2

Sense

Gnd

TPS7201QD

R4 82k

270k

160k

C5 10

+1.8V

Source

AD A1 NC GND

VCC

WP SCL SDA

C15

0.1

C16

0.001

3.3VD

AT24C256W

R22 10k

3.3VD

R29

100

32K x 8 EEPROM

+3.3VD

C26

0.1

GND

VCC

+3.3VD

Out

U9A

SN74LVC04A

4.096 MHz CRYSTAL

3.3VD

C44

0.1

C45

0.001

C46

0.1

C47

0.001

C48

0.1

C49

0.001

C50

0.1

C51

0.001

C52

0.1

C53

0.001

C54

0.1

C55

0.001

U1-4 U1-33 U1-56 U1-75 U1-112 U1-130

3.3VA (ANALOG) REGULATOR

1 2 3 4

C23

0.1

C4 10

Gnd EN In 1 In 2

Sense

Out 2 Out 1

R30 270k

U11

TPS7333QD

3.3VA

Source

6.8k

R11

1.8k

4.7

C24

0.001

VREF Source

0.1

1 2 3 4 5 6 7 8 9

A15 A14 A13 A12 A11 A10 A9 A8 NC1 NC2 WE# RESET# NC3 NC4 RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1

A101

A102

A103

A104

A105

A106

A107

A117

A118

A16

BYTE#

VSS1

DO15/A-1

DO7

DO14

DO6

DO13

DO5

DO12

DO4 VCC

DO11

DO3

DO10

DO2 DO9 DO1 DO8 DO0 OE# VSS CE#

R25 10k

3.3VD

A100

D115 D107 D114 D106 D113 D105

D104

D111

D112

D103 D110 D102 D109 D101 D108 D100

C20

0.1

C21

0.001

3.3VD

A108

A109

A110

A111

A112

A113

A114

A115

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

AM29LV800

A116

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22

A1 A2 A3 A4 A5 E DQA1 DQA2 DQA3 DQA4 VDD1 VSS1 DQA5 DQA6 DQA7 DQA8 W A6 A7 A8 A9 NC1

A16 A15 A14

G UB LB

DQB8 DQB7 DQB6 DQB5 VSS2 VDD2 DQB4 DQB3 DQB2 DQB1

NC3

A13 A12 A11 A10

NC2

24 23

3.3VD

U10A

SN74LVC04

U10B

SN74LVC04

MCM6323A

64K x 16 RAM

0.1C70.001

3.3VD

A100 A101 A102

D115

D113

D114

D112

D111 D110 D109 D108

A103 A104 A105 A106

A107

A108

A109

A110

D107

D106

D105

D104

D103

D102

D101

D100

A111

A112

A113

A114

A115

U9-14

C39

0.1

C56

0.1

C57

0.001

C58

0.1

C59

0.001

C60

0.1

C61

0.001

C62

0.1

C63

0.001

C64

0.1

C65

0.001

C66

0.1

C67

0.001

+1.8V

U1-16 U1-52 U1-68 U1-91 U1-125 U1-142

BUS TRANSCEIVER

AUDIO CODEC

512K x 16 FLASH

3.3VD

1.8V

C17

C18

C38

0.1

U10-14

C42

470pF

4.7k

+5V

0.6A

C41

470pF

U8-4

REVISED DSP BOARD SCHEMATIC DIAGRAM

Page 67

Revised January 2001

Part No. 001-9800-501

5-6

+ 5V

U12

SN74LVCC3245

VCCA DIR A1 A2 A3 A4 A5 A6 A7 A8 GND1 GND2

1 2 3 4 5 6 7 8

9 10 11 12

SCK

MOSI

VCCB

NC OE B1 B2 B3 B4 B5 B6 B7 B8

GND3

3.3VD

C22

0.1

+ 5V

U13

SN74LVCC3245

VCCA DIR A1 A2 A3 A4 A5 A6 A7 A8 GND1 GND2

VCCB

NC OE

B1 B2 B3 B4 B5 B6 B7 B8

GND3

3.3VD

C32

0.1

C31

0.1 U16A

7432

2 3

NC1 NC2 VSS1 DVDD1 A10 HD7 A11 A12 A13 A14 A15 NC3 HAS VSS2 NC4 CVDD1 HCS HR/W Ready PS DS IS R/W MSTRB IOSTRB MSC XF HOLDA IAQ HOLD BIO MP/MC DVDD2 VSS3 NC5 NC6

NC7

MC8

HCNTL0

VSS4

BCLKR0

BCLKR1

BFSR0

BFSR1

BDR0

HCNTL1

BDR1

BCKLX0

BCLKX1

VSS5

HINT/TOUT1

CVDD2

BFSX0

BFSX1

HRDY

DVDD3

VSS6

HD0

BDX0

BDX1

ACK

HBIL

NMI

INT0

INT1

INT2

INT3

CVDD3

HD1

VSS7

NC9

NC10

NC11

NC12

DBDD4

VSS0

CLKMD1

CLKMD2

CLKMD3

NC13

HD2

TOUT0

EMU0

EMU1/OFF

TD0

TD1

TRST

TCK

TMS

NC14

CVDD4

HPIENA

VSS9

CLKOUT

HD3

X2/CLKIN

A16

VSS10

A17

A18

NC18

NC17

CVDD6

A9A8A7A6A5

HD6

A3A2A1

DVDD6

HDS2

VSS12

HDS1

NC16

CVDD5

HD5

D15

D14

D13

HD4

D12

D11

D10

D9D8D7

DVDD5

VSS11

NC15

A19

VCC1 VCC2 VINR VREFL VREFR VINL RST ML SYSCLK LRCIN BCKIN DOUT

DGND

VDD

DIN

ZFLG

MC VOUTL VOUTR

VCOM

GND1

GND2

VCC3

1 2 3 4 5 6 7 8

9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

PCM3002

3.3VD

1.8V

R24 10k

R23 10k

R21 10k

R20 10k

3.3VD

R31 10k

R32 10k

R33 10k

1.8V

3.3VD

1.8V

1 2 3 4 5 6 7 8 9

10 12

13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

3738394041424344454647484950515253545556575859606162636465666768697071

108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73

143

142

141

140

139

138

137

136

135

134

133

132

131

130

129

128

127

126

125

124

123

122

121

120

119

118

117

116

115

114

113

112

111

110

109

144

MISO

MOSI

SCK

MISO

1 2 3 4 5 6 7 8

9 10 11 12

A118 A117

A116

D100

D101

D102

D103

D104

D105

D106

D107

D108

D109

D110

D111

D112

D113

D114

D115

3.3VD

A110 A111

A112 A113 A114 A115

A109

A108

A107

A106

A105

A104

A103

A102

A101

3.3VD

A100

C33

0.1

C34

0.001

3.3VD

C35

0.1

C36

0.001

3.3VA

C14

4.7

C11

4.7

R27

0 ohm

Not Used

C19

0.1

VREF

3.3VA

C37

0.1

1 9 11 2 3 7 14 12 6 5 4 8 10 12

3.3VD

R34

10k

R35

10k

R15 10k

TMS320VC5402

DIGITAL SIGNAL PROCESSOR

(DSP)

Serial Data

Serial Clock

VIAS TO AUDIO/LOGIC

BOARD J302

A11 A12 A13 A14 A15 A16 A17 A18 A19 A20

A1 A2 A3 A4 A5 A6 A7 A8 A9

A10

6 5 4 3 2 1

15 16 17 18 19 20

Receive Audio Transmit Audio

To J302, Pin:

1 2 3 4

SP1

Wire Harness To

Audio/Logic Board

From U102, Pin 1 Wire-Out Not Connected To U102, Pin 2 Wire-Out From Latch U112, Pin 14 (Output E)

To Audio/Logic Board

IN 2

–

U8B

MC3303

VREF

R16

30k

C12

390pF

R28

Rx Audio Amp

OUTPUT B

J3 1 9 2 5 6 3 4 8 10

R36

0 ohm

–

U8D

MC3303

VREF

R14 30k

C10

390pF

R9 15k

R19

–

U8D

MC3303

VREF

R13

30k

390pF

R12

15k

R26

IN 3

OUTPUT A

Rx In

Tx In

W301 W309 W302 W305 W306 W303 W304 W308 W310

W307

Rx Audio Amp

Tx Audio Amp

Option 1:

–

U8A

MC3303

VREF

R17 30k

C13

390pF

R18 18k

R1 2k

Tx Audio Amp

R37

0 ohm

R10

18k

R38 18k

C40

0.1

2 3

5 7 8

Source

Rx Audio Out

Tx Audio Out

Option 2:

W311 W319 W312 W313 W314 W315 W317 W318 W320

Source

C25

0.1

C29 100

0.5

C28 100

C27 100

+5V

Source

IN Out

Gnd

U15

TL750M

+5V REGULATOR

3.3VD (DIGITAL) REGULATOR

1 2 3 4

0.1

C30

Gnd EN In 1 In 2

Sense

Out 2 Out 1

3.3VD Source

270k

TPS7333QD

+1.8V REGULATOR

0.1

Gnd EN In 1 In 2

Sense

Gnd

TPS7201QD

82k

270k

160k

C5 10

+1.8V Source

AD A1 NC GND

VCC

WP SCL SDA

C15

0.1

C16

0.001

3.3VD

AT24C256W

R22 10k

3.3VD

R29

100

32K x 8 EEPROM

+3.3VD

C26

0.1

GND

VCC

+3.3VD

Out

U9A

SN74LVC04A

4.096 MHz CRYSTAL

3.3VD

C44

0.1

C45

0.001

C46

0.1

C47

0.001

C48

0.1

C49

0.001

C50

0.1

C51

0.001

C52

0.1

C53

0.001

C54

0.1

C55

0.001

U1-4 U1-33 U1-56 U1-75 U1-112 U1-130

3.3VA (ANALOG) REGULATOR

1 2 3 4

C23

0.1

C4 10

Gnd EN In 1 In 2

Sense

Out 2 Out 1

R30

270k

U11

TPS7333QD

3.3VA Source

6.8k

R11

1.8k

4.7

C24

0.001

VREF

Source

0.1

0 ohm

Analog Gnd Digital Gnd

1 2 3 4 5 6 7 8 9

A15 A14 A13 A12 A11 A10 A9 A8 NC1 NC2 WE# RESET# NC3 NC4 RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1

A101

A102

A103

A104

A105

A106

A107

A117

A118

A16

BYTE#

VSS1

DO15/A-1

DO7

DO14

DO6

DO13

DO5

DO12

DO4 VCC

DO11

DO3

DO10

DO2 DO9 DO1 DO8 DO0 OE# VSS CE#

R25 10k

3.3VD

A100

D115 D107 D114 D106 D113 D105

D104

D111

D112

D103 D110 D102 D109 D101 D108 D100

C20

0.1

C21

0.001

3.3VD

A108

A109

A110

A111

A112

A113

A114

A115

11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

AM29LV800

A116

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22

A1 A2 A3 A4 A5 E DQA1 DQA2 DQA3 DQA4 VDD1 VSS1 DQA5 DQA6 DQA7 DQA8 W A6 A7 A8 A9 NC1

A16 A15 A14

G UB LB

DQB8 DQB7 DQB6 DQB5 VSS2 VDD2 DQB4 DQB3 DQB2 DQB1

NC3

A13 A12 A11 A10

NC2

24 23

3.3VD

U10A

SN74LVC04

U10B

SN74LVC04

MCM6323A

64K x 16 RAM

0.1C70.001

3.3VD

A100 A101 A102

D115

D113

D114

D112

D111 D110 D109 D108

A103 A104 A105 A106

A107

A108

A109

A110

D107

D106

D105

D104

D103

D102

D101

D100

A111

A112

A113

A114

A115

U9-14

C39

0.1

C56

0.1

C57

0.001

C58

0.1

C59

0.001

C60

0.1

C61

0.001

C62

0.1

C63

0.001

C64

0.1

C65

0.001

C66

0.1

C67

0.001

+1.8V

U1-16 U1-52 U1-68 U1-91 U1-125 U1-142

BUS TRANSCEIVER

AUDIO CODEC

512K x 16 FLASH

3.3VD

1.8V

C17

C18

C38

0.1

U10-14

UNREVISED DSP BOARD SCHEMATIC DIAGRAM

Page 68

DSP BOARD SERVICING INFORMATION

109

C66

144

C28

108

C39

C44

C20 C7

122

C29

C27

U15

C21

C25

R25

U10

C38

C53

C52

C64 C65

C55

C54

C67

C30

C57

C45

C56

J2 J3

C63

R33

C62

C26

C50

R34

R15

C51

C47 C46

R32

C32

C31

112

R36

R11

C24

R12

R21

R20

C60

C61

C48

112

C59 C49

C58

R31

R29

U13

C23

U11

R10

C12

R23

C22

C19

R30

R28

R35

R24

R22

R38

R16

R14

C10

U12

C40

C37

U16

C16 C15

C33

R13

C34

R18

R17

A10

A1 A11

C35

C36

C13

R27

R26

R37

SP1

C17

R19

1 2

A20

A14

C18

C11

C14

UNREVISED DSP BOARD COMPONENT LAYOUT

5-7

Revised January 2001

Part No. 001-9800-501

Page 69

Part Number 001-9800-501

1-01 hph Printed in U.S.A.