EFITMENT SWIFT MAGNETIC
INCDOOR CYCLE BIKE
MODEL NO.:
IC035
IMPORTANT! Read
all instructions
carefully before
using this product.
Save this manual for
future reference.
EXERCISE
EQUIPMENT
QUESTIONS:
Contact customer
service at
service@zoovaa.com
USER MANUAL
2
At Efitment your safety is our top priority and to make sure both you and the unit remain in perfect working
order, we encourage you to read all the instructions before assembling and using your new Efitment machine.
Do not skip, substitute or modify any steps or procedures herein, as doing so could result in personal injury
and will void your warranty.
IMPORTANT SAFETY INSTRUCTIONS
1. Before starting any exercise program you
should consult your physician to determine if
you have any medical or physical conditions
that could put your health and safety at risk or
prevent you from using the equipment
properly. Your physician’s advice is essential if
you are taking any medication that may affect
your heart rate, blood pressure, or cholesterol
level.
2. Be aware of your body’s signals. Incorrect or
excessive exercise can damage your health.
Stop exercising if you experience any of the
following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath,
lightheadedness, dizziness, or feelings of
nausea. If you experience any of these
conditions, you should consult your physician
before continuing with your exercise program.
3. This equipment is intended for adult use only.
Keep children and pets away from the
machine. DO NOT leave children unattended
in the same room with the equipment.
4. Use the equipment on a solid, flat level
surface with a protective cover for your floor
or carpet. To ensure safety, the equipment
should have at least 2 feet of free space all
around it.
5. Check if you have all the components and tools
listed. Please note that some components are
pre-assembled to help make the assembly
process quick and easy.
6. Always use the equipment as intended. If you
find any defective components while
assembling or checking the equipment, or if you
hear any unusual noises coming from the
equipment during exercise, discontinue use
immediately and do not use until the problem
has been rectified.
7. Always wear appropriate workout clothing
when exercising. Do not wear clothing that
can get tangled in the equipment.
8. Keep hands and other objects away from all
moving parts.
9. The maximum user’s weight is 265 lbs/ 120kgs.
10. Be careful when lifting and moving the
equipment. Always use proper lifting technique
and seek assistance if necessary.
11. Your equipment is intended for use in cool, dry
conditions. You should avoid storage in extreme
cold, hot, or damp areas as this may lead to
corrosion and other related problems.
12. This equipment is designed and intended for
indoor use only, not for commercial use.
SAVE THESE INSTRUCTIONS
3
6
7
6
5
8
6
7
6
5
8
9
10
11
4
2
3
1
4
13
4
12
4
9
10
11
#94 S6
#95 S13*14*15
2
3
2
3
2
3
9
10
11
14
15
16
16
17
18
19
20
21
22
23
23
23
23
23
23
24
25
26
27
26
28
29
32
31
30
32
33
34
35
36
44
45
37
38
39L
41
41
42
42
43L
42
42
42
39R
38
43R
50
49
48
42
41
42
42
13
45
46
41
10
11
10
11
26
26
52
50
53
54
55
56
57
50
53
54
55
60
61
58
59
51
47
61
64
64
62
63
65
66
67
68
70
71
73
77
68
69
67
66
72
69
11
74
75
76
76
85
78
84
84
80
79
79
80
86
76
10
88
81
41
89
86
82
83
37
40L
40R
42
41
42
41
41
87
16
90
91
77
93
93
92
2
3
EXPLODED DRAWING
4
No.
Description
Qty. No.
Description
Qty.
1
Front Stabilizer
1 39L/R
Crank 2 2
Hexagon Nut M8*H5.5*S14
5 40L/R
Pedal 2 3
Foot Pad ф43*14*M8*25
5 41
Screw ST4.2*16*Φ8
6
4
End Cap PT70*30*20
4 42
Screw ST4.2*19*Φ8
10
5
Screw M6*12*S5
2 43L/R
Belt Cover
2
6
Bearing 608ZZ
4 44
C Clip d17
1
7
Transport Wheel Φ71*Φ19*24
2 45
Bearing 6203-2RS
2
8
Screw Φ7.8*30*M6*15*S5
2 46
Bushing Φ22*Φ18*5.5
1
9
Screw M8*20*S6
4 47
Magnet Φ15*7
1
10
Spring Washer d8
10 48
Belt Wheel Φ220*20*Φ17.1*4-Φ6*Φ60-6PJ
1
11
Washer d8*Φ16*1.5
10 49
Middle Axle Φ17*188*59.5*78*4-Φ6.1*Φ60
1
12
Rear Stabilizer
1 50
Bolt M6*16*S10
6
13
Knob M16*1.5*27*Φ56
2 51
Belt 1 14
Bushing PT80*40*PT70*30*L130
1 52
Tension Knob
1
15
Brake Block 68*75*39.2
1 53
Spring Washer d6
2
16
Screw M5*7*Φ10
6 54
Washer d6*φ12*1.2
2
17
Brake Cable Φ1.5*255*42
1 55
Ring-Shield d12
2
18
Bolt M6*10*H26*S5
1 56
Magnet 40*25*10
8
19
Brake Handle
1 57
Magnet Holder 45.5*130*10.5
2
20
Washer Φ8.5*Φ23.5*3
1 58
Magnetic Plate
1
21
Spring Φ1.2*Φ11*21*N7
1 59
Magnetic Plate Shaft φ12*53.5*47.4*M6
1
22
Cable Base t3*25*23
1 60
Screw ST3*10*Φ5.6
8
23
Nylon Nut M6*H6*S10
9 61
SpringΦ1.5*Φ15*54*N9
2
24
Hexagon Bolt M6*10*S10
1 62
Brake Pad 60*27*5
1
25
Washer d6*Φ16*1.5
1 63
Brake Pad Holder
1
26
Bearing 6001-2RS
4 64
Screw M6*16*S5
2
27
Idle PulleyФ39*Ф34*24
1 65
Brake Connected Plate
1
28
Wave Washer d12*Φ15.5*0.3
1 66
Hexagon Nut M12*1*H11*S18
2
29
Seat 1
67
Sleeve Φ22*Φ12.2*7
2
30
Seat Slider
1 68
Bolt M6*50*Φ12*4
2
31
Seat Post
1 69
Hexagon Nut M6*H5*S10
2
32
End Cap PT50*25*16
2 70
Hexagon Nut M12*1*H7*S19
1
33
Washer d10*Φ30*2.5
1 71
Sleeve Φ18*Φ12.2*21
1
34
Knob M10*Φ58*32
1 72
Flywheel
1
35
Cover 99.3*83.5*24.7
1 73
Flywheel Axle
1
36
Bushing PT70*30*PT60*20*L145*10
1 74
Handlebar Post
1
37
Crank Plug Φ25*7
2 75
Screw M5*8*Φ10
1
38
Hexagon Nut M10*1.25*H7.5*S14
2 76
Screw M8*16*S6
6
PARTS LIST
5
77
Nut M12*1*H5*S19
2 87
Meter 1 78
Handlebar
1 88
Trunk Line
1
79
End Cap Φ25*16
2 89
Sensor Wire
1
80
Foam Grip Φ23*3*420
2 90
PU Washer
1
81
Main Frame
1 91
Tension Knob Bracket
1
82
Washer d5*Φ13*1
1 92
Wave Washer d17*Φ22*0.3
1
83
Screw M5*16*Φ8
1 93
Washer d5*φ10*1.0
4
84
Pulse Sensor
2 94
Allen Wrench S6
1
85
Screw ST4.0*19*Φ11
2 95
Spanner S13*14*15
1
86
Plug Φ12*11*Φ3
2
HARDWARE PACKAGE
EXPLODED DRAWING
#9 M8*20*S6 4PCS
#10 d8 4PCS
#11 d8*Φ16*1.5 4PCS
Steps 1
Steps 2
#33 d10*Φ30*2.5 1PC
#34 M10*Φ58*32 1PC
Steps 3
#95 S13*14*15 1PC
#94 S6 1PC
#10 d8 6PCS
#11 d8*Φ16*1.5 6PCS
#76 M8*16*S6 6PCS
6
11
10
76
11
10
76
11
10
76
78
13
#94 S6 1PC
Figure B
89
88
74
81
88
89
#76 M8*16*S6 6PCS
#10 d8 6PCS
#11 d8*Φ16*1.5 6PCS
Figure A
ASSEMBLY INSTRUCTIONS
STEP 1:
Attach the Front & Rear Stabilizer (No.1 & 12)
to the Main Frame (No.81) using 4 Screws
(No.9), 4 Spring Washers (No.10) and 4
Washer (No.11). Tighten with an Allen
Wrench (No.94).
Attach Left Pedal (No.40L) to Left Crank
(No.39L). Turn the Left Pedal (No.40L)
counter-clockwise with the hand until it is
tight, then use Spanner (No.95) to securely
tighten. Attach Right Pedal (No.40R) to Right
Crank (No.39R). Turn the Right Pedal (No.40R)
clockwise with the hand until it is tight, then
use Spanner (No.95) to securely tighten.
Note: The Pedals (No.40L/R) are marked "L"
and "R" for Left and Right. Make sure you
attach the correct pedal to the corresponding
crank.
STEP 2：
Insert Trunk line (No. 88) through Handlebar
Post (No.74). Then attach the Handlebar
(No.78) to Handlebar Post (No.74) using 6
Screws (No.76), 6 Spring Washers (No.10),
and 6 washers (No.11). Tighten with an Allen
Wrench (No.94). (Figure B)
Loosen and pull out the Knob (No.13) from the
Main Frame (No.81). Insert the Handlebar
post (No.74) with Trunk line (No.88) into Main
frame (No.81) at desired position. Put back
and secure with the Knob (No.13).
Connect Trunk line (No.88) with Sensor Wire
(No.89). (Figure A)
9
10
11
9
10
11
1
12
40L
40R
81
#94 S6 1PC
#95 S13-14-15 1PC
S15
39R
39L
#9 M8*20*S6 4PCS
#10 d8 4PCS
#11 d8*Φ16*1.5 4PCS
7
ASSEMBLY INSTRUCTIONS
STEP 3：
Attach the Seat Slider (No.30) to the Seat
Post (No.31), tighten and secure with Washer
(No.33) and Knob (No.34).
Attach the Seat (No.29) to the Seat slider
(No.30), tighten and secure with Spanner
(No.95).
Assembly is complete!
81
#95 S13-14-15 1PC
S13
#33 d10*Φ30*2.5 1PC
#34 M10*Φ58*32 1PC
13
30
33
31
34
29
8
52
19
8
7
6
5
4
A
B
8
7
6
5
4
Figure B Figure A
TENSION ADJUSTMENT
PEDAL STRAP ADJUSTMENT
When the pedal is tight, press the buckle
and pull the strap up to loosen the strap.
(Figure A).
When the pedal is loose, press the buckle
and pull the strap down to fasten the strap
(Figure B).
A. Adjusting the Tension:
Increasing or decreasing the tension allows
you to add variety to your workout sessions.
To increase the tension, rotate the Tension
Knob (No.52) (“+”) clockwise. (Arrow A)
To decrease the tension, turn the Tension
Knob (No.52) (“-”) counter-clockwise.
(Arrow B)
B. Emergency Brake Function:
The Brake Handle (No.19) is emergency
brake. Use this safety feature in any
situation when you would need to get off
the bike or stop the bike’s flywheel.
During exercise, press down firmly on the
Brake Handle (No.19) to stop the bike
immediately.
9
13
78
74
SEAT AND HANDLEBAR ADJUSTMENT
The seat of this bike is fully adjustable as it
moves Up, Down, Forward and Backward.
A. To adjust the height of the Seat Post
(No.31), loosen and pull out the Knob
(No.13), then raise or lower the seat to the
desired height. Once adjusted, re-insert and
tighten the Knob (No.13) to secure the seat
in place. (Figure A)
B. To adjust the seat forward and backward,
loosen Knob (No.34), then slide the Seat
Slider (No.30) to the desired position. Once
positioned, tighten the Knob (No.34) to
secure the Seat Slider (No.30) in place.
(Figure B)
C. To adjust the height of Handlebar
(No.78), loosen and pull on the Knob
(No.13), then slide the Handlebar Post
(No.74) up or down to the desired height.
Once adjusted, tighten the Knob (No.13) to
secure the Handlebar Post (No.74) in place.
Figure A Figure B
13
31
30
34
10
A
B
#95 S13-14-15 1PC
S14
3
2
12
1
BALANCE ADJUSTMENT
To achieve a smooth and comfortable experience, you must ensure that the bike is stable.
During use, if you notice that the bike is unbalanced, you can adjust the Foot Pads (No.3)
located beneath the Front & Rear Stabilizers (No.1 & 12).
To adjust, use the Spanner (No.95) to loosen the Hexagon Nut (No.2) by turning it clockwise.
With the nut loosened, rotate the Foot Pads (No.3) until it sits level with the surface that the
bike is on.
When you have finished adjusting the Foot Pads (No.3), re-tighten the Hexagonal Nut (No.2)
by turning it counter-clockwise using Spanner (No.95). If needed, repeat this process to adjust
the remaining Foot Pads (No.3).
11
HOW TO MOVE THE BIKE
To move the bike, first ensure that the Handlebar (No.78) is properly secured. If the Handlebar (No.78) is
loose, tighten the knob (No.13) to secure it. Next, stand at the front of the bike so that you’re directly in
front of the Handlebar (No.78). Firmly grasp and hold each side of the Handlebar (No.78), place one foot
on the front base and tilt the bike towards you until the Transport Wheels (No.7) on the front base touch
the ground. With the wheels on the ground, you can transport the bike to the desired location with ease.
78
13
7
12
SPECIFICATIONS:
TIME-------------------------------------------00:00 - 99:59 MIN: SEC
SPEED-----------------------------------------------------0.0 - 240 M/H
DISTANCE-----------------------------------------------0.00 - 999.9 M
CALORIES---------------------------------------------0.0 - 999.9 KCAL
PULSE-------------------------------------------- 40 - 240 BEATS/MIN
KEY FUNCTION:
MODE: Push to select functions.
OPERATION PROCEDURES:
AUTO ON/OFF: The monitor will be automatically shut off if there is no signal coming in for 4 minutes. The
monitor will be auto-powered when start exercises or press the key.
FUNCTION:
TIME (TMR): Count the total time from exercise start to end.
SPEED (SPD): Display the current speed.
DISTANCE (DST): Count the distance from exercise start to end.
CALORIES (CAL): Count the total calories from exercise start to end.
PULSE (PUL): Display your heart rate per minute when hold on reaction planks with both hands.
SCAN: The computer will rotate through through each function: TIME, SPEED, DISTANCE, CALORIES, PULSE.
BATTERY: The computer uses 2 AAA batteries, which are included. If there is a problem with the display, try
changing the batteries first. When changing the batteries, change both of them. Do not mix old and new
batteries. Do not mix battery types. Dispose the batteries according to the laws and regulations of your
local region. Some batteries may be recycled. When disposing or recycling, do not mix battery types.
COMPUTER INSTRUCTIONS
V1
Loading...