EF HB FG 3060 TN VSB, HB FG 4060 TN VSB, HB FG 3070 TN VSB, HB FG 4090 TN VSB, HB FG 5070 TN VSB User Manual

1

HB FG 3060 TN VSB HB FG 4060 TN VSB HB FG 3070 TN VSB

HB FG 4090 TN VSB HB FG 5090 TN VSB HB FG 5070 TN VSB

BUILT-IN GAS HOB

BATTERY IGNITION

THE BEAUTY OF SIMPLICITY

Model:

HB FG 3060 TN VSB [ 141252-11 ]
HB FG 3070 TN VSB [ 141253-11 ]
HB FG 4060 TN VSB [ 141250-11 ]
HB FG 4090 TN VSB [ 141251-11 ]
HB FG 5070 TN VSB
HB FG 5090 TN VSB

USER MANUAL

2

Congratulations on choosing our product, which you will find is dependable and easy to use. We recommend
that you read this manual for best performance and to extend the life of your appliance. Thank you.

Close-up View

1. Auxiliary Gas Burners

2. Semi-rapid burner

3. Rapid burner

4. Triple ring burner

5. Igniter for Gas Burners (only on certain models)

6. Safety Device (only on certain models) - Activates if the flame
accidentally goes out (spills, drafts, etc.), interrupting the delivery of gas
to the burner.

7. Control Knobs for Gas Burners and Electric Hot Plates

3

How To Use Your Appliance
The position of the corresponding gas burner is indicated on each control knob.

GAS BURNERS

The burners differ in size and power. Choose the most appropriate one for the diameter of the cookware being
used.
The burner can be regulated with the corresponding control knob by using one of tile following settings:

OFF

High

Low

IGNITING THE BURNERS

All models come with auto ignition and the safety device. Proceed as follows to ignite the burner：

1) Turn the chosen knob in anti-clockwise direction to the “High” setting.

2) Push in and hold the knob for 3 to 5 seconds to light the gas and to permit the thermocouple to heat up.

3) Release the knob after 3 to 5 seconds and adjust the flame as desired. Repeat points 1 and 2 if the
flame cannot be lighted.

Caution: If the burner accidently goes out, the safety valve will automatically cut out the gas flow. To re-light

the burner, turn the control knob back to “OFF” setting and try to re-light again after waiting for at least I minute.

Turn off a burner, turn the knob in the clockwise direction until it stops (it should be on the " " OFF setting).

BATTERY IGNITION

If the auto ignition does not work, make sure that the battery, installed at the back of the cooker, is not flat and
has been installed correctly.

CHOSE OF THE BURNERS

For greater efficiency and lesser gas consumption, use the pots and pans with the right
diameters of the burners. Avoid having flames extending out from underneath the pans (refer to
the table). A smaller diameter pot or pan placed on a larger burner does not necessarily mean
that the boiling conditions are reach quicker.

Table of recommended

pans

Burner Ø Pan diameter in cm

Auxiliary

Semi rapid

Rapid

Triple ring

from dia. 8 to dia. 14
from dia. 14 to dia. 20
from dia. 20 to dia. 28

Above dia. 26

AUTOMATIC SAFETY VALVES

This safety device automatically closes the gas valve if the inconvenience caused by failure to comply with this
rule.

4

Cleaning and Maintenance
Cleaning and maintenance should be carried out after the appliance has turned cold especially when cleaning

the enameled parts. Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on the surfaces.
Avoid using acid or chlorine-based cleaning products.

To extend the life of the cooktop, it is absolutely indispensable that the appliance be
cleaned carefully and thoroughly on a frequent basis, keeping in mind the following:

 BURNERS AND GRIDS These parts can be removed and cleaned with soapy water or with non-abrasive

products. After cleaning the burners and their flame distributors must be well dry (Failure to do so, it may
cause the burner cap to be rusty) and correctly replaced. It is very important to check that the burner flame
distributor F and the cap C has been correctly positioned (fig.1), failure to do so can cause serious
problems. Check that the electrode “S” (fig.1) is always clean to ensure trouble-free sparking. Check that
the probe” T” (fig.1) is always clean to ensure correct operation of the safety valves (for models with safety
device).

 STAINLESS STEEL can be stained if it remains in contact with highly calcareous water or aggressive

detergents (containing phosphorous) for an extended period of time, it is recommended that these parts be
rinsed thoroughly with water and then dry well, It is also advisable to clean up any spills.

Note: regular use could cause discoloring around the burners due to high flame temperature.

Both the probe and ignition plug must be very carefully cleaned

●GAS TAPS

Periodic lubrication of the gas taps must be carried out by specialist personnel only. In the event of operating
faults in the gas taps, call the Service Department.

GENERAL ADVICE

√ When the appliance is not being used; it is advisable to keep the gas tap closed.
√ If the gas tap becomes stiff, it is necessary to dismount it accurately, clean it with gasoline and spread a

bit of special grease resistant to high temperatures on it. This operation must be executed by a qualified
technician.