EF BO AE 102 A User Manual

Multifunction Oven

BO AE 102 A

THE BEAUTY OF SIMPLICITY

USER MANUAL

Using This Manual

This Owner’s Manual contains important information on safety and instructions intended to assist you in the operation and
maintenance of your appliance.
Please take the time to read this Owner’s Manual before using your oven and keep this book for future reference.

The following symbols are used in the text of this Owner’s Manual

Safety Instructions

Installation of this oven must be performed only by a licensed electrician. The installer is responsible for connecting the appliance to the mains
power supply in observance of the relevant safety recommendations.

Electrical safety

If the oven has been damaged in transport, do not connect it.

● Appliance must be connected to the mains power supply only by a specially licensed electrician.

 In the event of a fault or damage to the appliance, do not attempt to operate it.
 Repairs should be performed by a licensed technician only. Improper repair may result in considerable danger to you

and others. If your oven needs repair, contact a Service Centre or your dealer.

 If the supply cord is defective, it must be replaced by a special cord or assembly available

from the manufacturer or an authorized service agent.

 Electrical leads and cables should not be allowed to touch the oven.
 Install an omnipolar circuit-breaker with a minimum contact opening of 3 mm between the appliance and the mains .The omnipolar

circuit breaker should be sized according to the load and should comply with current regulations (the earth wire should not be interrupted
by the circuit breaker ).

 The rating plate is located on the right side of the door.
 The power supply of the appliance should be turned off when it is being repaired or cleaned.
 Take care when connecting electrical appliances to sockets near the oven.

WARNING

The appliance should be powered down before replacing the lamp to avoid the possibility of electric shock. During oven operation, the interior
surfaces become very hot.

Safety during operation

 This oven has been designed only for the cooking of household foods.
 During use, the oven interior surfaces become hot enough to cause burns. Do not touch heating elements or

interior surfaces of the oven until they have had time to cool.

 Never store flammable materials in the oven.
 The oven surfaces become hot when the appliance is operated at a high temperature for an extended period of time.
 When cooking, take care when opening the oven door as hot air and steam can escape rapidly.
 When cooking dishes that contain alcohol, the alcohol may evaporate due to the high temperatures and the vapour can catch fire if it

comes into contact with a hot part of the oven.

 For your safety, do not use high-pressure water cleaners or steam jet cleaners.
 Frozen foods such as pizzas should be cooked on the wire grill. If the baking tray is used, it may become deformed due to the great

variation in temperatures.

 Do not pour water into the oven bottom when it is hot. This could cause damage to the enamel surface.
 The oven door must be closed during cooking.
 Do not line the oven bottom with aluminium foil and do not place any baking trays or tins on it. The aluminium foil blocks the heat, which

may result in damage to the enamel surfaces and cause poor cooking results.

 Fruit juices will leave stains, which can become indelible on the enamel surfaces of the oven. When cooking

very moist cakes, use the deep pan.

 Does not rest bake ware on the open oven door.
 This appliance is not intended for use by young children or infirm persons without the adequate supervision of a responsible person

ensuring that they are using the appliance safely.

 Ensure that the appliance is switched off before replacing the lamp to avoid the possibility of electric shock.
 If a cooking time is not entered, the oven will shut itself off after the lengths of time indicated below.

Child safety

 Children of less than 3 years should be kept away unless continuously supervised.
 Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in

its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.

 CAUTION- Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and

vulnerable people are present.

 This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved.

 Children shall not play with the appliance.
 Cleaning and user maintenance shall not be made by children without supervision.
 The appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.

 Children should be supervised to ensure that they do not play with the appliance.
 Keep electrical appliances out of reach from Children or infirm persons. Do not let them use the appliances without supervision.
 WARNING: Accessible parts may become hot when the grill is in use. Children should be kept away.
 WARNING: Ensure that the appliance is switched off before replacing the lamp to avoid electric shock.
 Always place oven racks in desired location while oven is cool. If a rack must be moved while oven is hot, do not let potholder contact

the heating elements.

 Always use dry potholders. Moist or damp potholders on hot surfaces may result in burns from steam. Do not let potholder touch hot

heating elements. Do not use a towel or other bulky cloth.

 WARNING: Accessible parts may become hot during use. You children should be kept away.
 Secure all loose garments, etc. before beginning. Tie long hair so that it does not hang loose, and do not wear loose fitting clothing or

hanging garments, such as ties, scarves, jewelry, or dangling sleeves.

 When children become old enough to use the appliance, it is the legal responsibility of the parents or legal guardians to ensure that they

are instructed in safe operation of the appliance by qualified persons.

 Do not allow anyone to climb, stand, lean, sit, or hang on any part of an appliance, especially a door, warming drawer or stora

ge

drawer. This can damage the appliance, and the unit may tip over, potentially causing severe injury.

 WARNING: The appliance and its accessible surface parts become hot during use. Care shall be taken to avoid touching heating

elements. Do not allow children less than 8 years of age to use this appliance unless closely supervised by an adult. Children and pets
should not be left alone or unattended in the area where the appliance is in use. They should never be allowed to play in its vicinity,
whether or not the appliance is in use.

Cleaning Safety

CAUTION:

Items of interest to children should not be stored in an appliance, in cabinets above an appliance or on the backsplash. Children climbing on
an appliance to reach items could be seriously injured.
Do not clean the appliance while it is still hot. Some cleaners produce noxious fumes when applied to a hot surface. Wet clothes or sponges
can cause burns from steam.

Oven exterior

● For cleaning both the interior and exterior of the oven, use a cloth and a mild cleaning agent or warm soapy water.

● Dry with kitchen paper or a dry towel.

● Do not use scourers, caustic cleaners or abrasive products.

Stainless steel oven fronts

● Do not use steel wool, scouring pads or abrasives. They may damage the finish.

Aluminium oven fronts

● Wipe the plate gently with a soft cloth or microfiber cloth and a mild window cleaning detegent.

WARNING

Make sure the oven is cool before cleaning.

Oven interior

● Do not hand - clean the door seal.

● Do not use coarse scouring pads or cleaning sponges.

● To avoid damaging the enameled oven surfaces, use commercially available oven cleaners.

● To remove stubborn soil, use a special oven cleaner.

Oven door glass

The oven door is equipped with three sheets of glass placed against each other. The inner & middle sheets can be removed for cleaning.
WARNING

● Whenever the door is separated from the oven, the clips should be flipped open.

● Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can cascratch the surface, which

may resulting in shattering of the glass.

● When the door is mounted, removing some of the parts (the door glass or some other part) from the door may result in injury.

Attention
The glass may break if you use excessive force especially at the edges of the front sheet.

Accessories

Wash all bakeware and accessories after each use and dry with a kitchen towel.To clean easily, soak in warm soapy water for about 30
minutes.

Catalytic enamel surface

The removable cover casing is coated with a dark gray catalytic enamel that can become coated with oil and fat distributed by circulating air
during convection heating. These deposits will burn off at oven temperatures of 200 °C and higher, for example, when baking or roasting.

Higher temperatures will result in faster burning.The oven and accessories should be cleaned after each use. Otherwise further baking and
roasting will cause the deposits to bake on even harder and cleaning may become difficult and in extreme cases impossible.

Cleaning by hand

Make sure the oven is cool before cleaning.

● The catalytic enameled cover casing should be cleaned using a solution of hot water and washing-up liquid applied with a soft nylon

brush.
Do not use abrasive cleaning agents, hard brushes, scouring pads or cloths, steel wool, knives or other abrasive materials.Do not use oven
spray on catalytic enamel as the chemicals used in oven sprays will damage catalytic enamel and render it ineffective.
If using oven sprays on the interior oven surfaces, the catalytic cover casing must first be removed from the oven.

Cleaning with high temperatures

Before cleaning the catalytic cover casing with high temperatures, make sure that all interior oven surfaces have been cleaned as described
above. Otherwise, the high temperatures can bake deposits onto the interior oven surfaces and make them impossible to remove.
If, after manual cleaning, the oven is still heavily soiled, heating it to a high temperature will help remove soiling caused by oil and grease
splashes.
Note that deposits of spices, syrups and similar substances are not removed by this process. These should be removed by hand with a mild
solution of hot water and washing-up liquid applied with a soft brush.

● Remove all accessories from the oven.

● Set the oven to conventional function.

● Set the heat to 250 °C.

● Run the oven for approximately 1 hour. The length of time will depend on the degree of soiling.

It is a good idea to set the finish time for the process using the end time setting, in case you forget to switch the oven off at the end.
Any remaining soil will gradually disappear with each subsequent use of the oven at high temperatures.

Disposal Instructions

Disposing of the packaging material

 The material used to package this appliance is recyclable.
 Dispose of the packaging materials in the appropriate container at your local waste disposal facility Disposing

of old appliances

WARNING

Before disposing of old appliances, make them inoperable so that they cannot be a source of danger.

To do this, disconnect the appliance from the mains supply and remove the mains lead.

To protect the environment, it is important that old appliances are disposed of in the correct manner.

 The appliance must not be disposed of with household rubbish.
 You can obtain information about collection dates and public refuse disposal sites from your local refuse department or council.

Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact you local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumb, hazardous substances can leak into the groundwater and get into the food chain,

4

5

m

m

．

5

6

0

m

m

．

damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of
charge.

Installing the Oven

Electrical installation of this appliance must be performed only by a licensed electrician.
The oven must be installed according to the instructions supplied.
Remove the protective vinyl from the door after installation.

Safety instructions for the installer

 Installation must guarantee protection against exposure to electrically live parts.

Installation of Built-in Ovens

In order to ensure that the built-in appliance functions properly, the cabinet containing it must be appropriate .The figure below gives the
dimensions of the cut-out for installation under the counter or in a wall cabinet unit.

5

9

5

595

5

6

5

2

2

595

5

6

5

5

9

5

2

0

0

M

I

N

2

2

2

0

0

M

I

N

4

5

m

i

n

4

5

m

i

n

4

5

m

i

n

4

5

m

i

n

4

5m

i

n

594

5

9

4

5

4

7

.

8

5

7

7

.

2

2

1

5

9

4

5

9

4

5

4

7

.

8

5

7

7

.

2

2

1



N. B :Installation in compliance with the consumption declaration
In order to ensure adequate ventilation ,the back panel of the cabinet unit must be removed .Installing the oven so that it rests on two strips
of wood is preferable .If the oven rests on a continuous ,flat surface ,there must be an aperture of at least 45×560mm .

The panels of the adjacent cabinets must be made of heat-resistant material .In particular ,cabinets with a veneer exterior must be assembled
with glues which can withstand temperatures of up to 100℃.

Incompliancewithcurrentsafetystandards,contactwiththeelectricalpartsofthe ovenmustnotbe possibleonce ithas
beeninstalled.

All parts, which ensure the safe operation of the appliance, must be removable only with the aid of a tool.
To fasten the oven to the cabinet, open the door of the oven and attach it by inserting the 4 wooden screws into the 4 holes located on the
perimeter of the frame.

Electrical Connection

Those ovens equipped with a three-pole power supply cable are designed to operate with an alternating current .The wire for earthling the
appliance is yellow-green in color.

Fitting on a Power Supply Cable

Opening the terminal board:

· Using a screwdriver ,prize the bolt on the side tabs of the
terminal board cover ;

· Using a screwdriver unhooking the no.2fixing hooks,
pull open the cover of the terminal board.
To install the cable, proceed as follows:

· Remove the wire clamp screw and the three contact screws L-N -

· Fasten the wires beneath the screw heads using the following color scheme :Blue (N) Brown (L) Yellow-Green

· Fasten the supply cable in place with the clamp and close the cover of the terminal board .

Connecting the supply cable to the mains

Install a standardized plug corresponding to the load indicated on the data plate. When connecting the cable directly to the mains, install an
omni polar circuit breaker with a minimum contact opening of 3 mm between the appliance and the mains .The omni polar circuit breaker
should be sized according to the load and should comply with current regulations (the earth wire should not be interrupted by the circuit
breaker).
The supply cable should be positioned so that it does not reach a temperature of more than 50℃with respect to the room
temperature ,anywhere along its length , or protected by insulation sleeping having an appropriate rating.
Before making the connection, check that:

· The electrical safety of this appliance can only be guaranteed if the cooker is correctly and efficiently earthed ,in compliance with
regulations on electrical safety. Always ensure that the earthling is efficient; if you have any doubts call in a qualified technician to check the
system .The manufacturer declines all responsibility for damage resulting from a system which has not been earthed.

· Before plugging the appliance into the mains ,check that the specifications indicated on the date plate (on the appliance and /or
packaging )correspond to those of the electrical mains system of your home .

· Check that the electrical capacity of the system and sockets will support the maximum power of the appliance ,as indicated on the data
plate .If you have any doubts, call in a qualified technician.

· If the socket and appliance plug are not compatible ,have the socket replaced with a suitable model by a qualified technician . The latter,
in particular, will also have to ensure that the cross section of the socket cables are suitable for the power absorbed by the appliance. The
use of adapters, multiple sockets and /or extensions, is not recommended. If their use cannot be avoided, remember to use only single or
multiple adapters and extensions which comply with current safety regulations .In these cases, never exceed the maximum current capacity
indicated on the single adapter or extension and the maximum power indicated on the multiple adapter .The plug and socket must be easily
accessible.