5540M Tone Generator and 5532M
Speaker/Amplifier Installation Sheet
Speaker/Amplifiers are heavy-duty, stand-alone signaling
devices that operate from local power and sound a tone
programmed at the Tone Generator. Speaker direction and
the output level are easily adjustable. Up to 2500 of these
Speaker/Amplifiers can be connected in parallel to the tone
output of a single tone generator.
Recording a Voice Message (5540MV
Series)
WARNING: High voltage is present when product is
energized.
Four five-second messages (or one twenty-second
message) can be recorded on the voice module unit. Refer
to Figure 16.
Description
Edwards Tone Generator and Speaker/Amplifiers are
intended for industrial applications where high audible output
and microcomputer reliability are required. The Adaptatone
Millennium Series are UL and cUL Listed as Audible Signal
Appliances for use in the hazardous locations listed in
Table 1.
The 5532B Speaker/Amplifiers are UL Listed and CSA
Certified as Audible Signaling Appliances.
The 5532M-Y6 is additionally UL Listed in a Speaker and
Amplifier category, when powered with 120V/240 VAC 50/60
Hz, for use in conjunction with the 5541M-Y6 Millennium
System Master either for emergency/evacuation, non-fire, or
for supplementary fire alarm control panel accessory
applications (see Instructions for 5541M-Y6, part 3100471).
The Tone Generator operates from local power. It
accommodates up to four normally-open contacts on its
inputs. The tone that sounds in response to an active input
is determined by setting miniature programming switches
inside the unit. Table 6 has switch settings for setting tones.
Four tones may be programmed into the Tone Generator at
any time. These tones operate on a pyramid-type priority
system. The tone programmed on SW1 overrides the tones
programmed on SW2, SW3, and SW4. The tone on SW2
overrides the tones programmed on SW3 and SW4.
Likewise, the tone on SW3 overrides the tone programmed
on SW4. The tone programmed on SW4 has the lowest
priority and cannot override any other programmed tone.
1. Put switches A and B on the programming dipswitch in
the proper position for the message to be recorded
(Figure 16). For programming a message longer than
five seconds, use Message Location 1.
Message
Location
1 0 Sec CLOSED CLOSED
2 5 Sec OPEN CLOSED
3 10 Sec CLOSED OPEN
4 15 Sec OPEN OPEN
2. Put switch PGM on the programming dipswitch in the
“CLOSED” position for programming mode (Figure 16).
3. Press and hold the record button while speaking clearly
into the microphone to record your message. Release
the button when recording is complete.
4. To test the message, press and hold PLAY while in
programming mode.
NOTE: This will play only the current location.
WARNING: High volume may cause harm to personnel in
close proximity.
5. Adjust the volume as necessary. Set the main volume
using the potentiometer on the main board (Figure 14 Figure 16) and then set the voice volume using the
potentiometer on the voice module board (Figure 16).
Start Switch A
Settings
Switch B
Settings
© 2010 UTC Fire & Security. All rights reserved. 1 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
Installation
The Adaptatone may be mounted to any flat surface or may
be used as a freestanding unit mounted to a rigid pipe. The
Adaptatone must be installed in accordance with the latest
edition of the National Electrical Code or other regulations
applicable to the country and locality of installation and by a
trained and qualified electrician.
NOTE: The increased resistance due to long wire runs
needs to be accounted for in sizing wire. Consult
Applications Engineering for details.
For catalog numbers ending in "AQ", 24 VAC power must be
transformer isolated from mains or line power.
WARNING: To prevent fire, shock and component damage,
NO work, including circuit board removal, should be
performed while the circuit is energized.
WARNING: To ensure integrity of the Adaptatone assembly
when adjusting the speaker direction, make sure threads in
the enclosure remain fully engaged and do not turn speaker
more than 360 degrees from the original factory installed
position.
Ensure that the (4) collar gaskets, part number P-0419300362, are in place on each cover screw before securing the
signal box cover.
When securing cover, start screws by hand, making sure
they are threaded into tapped holes in housing bosses
before securing with a screwdriver. Torque signal box cover
screws to a minimum of 20 in-lbs. This ensures the required
tight fit.
Retighten nut and turn speaker slightly clockwise until
locked into place.
NOTE: Any kind of service or maintenance performed
while unit is energized will void the warranty.
1. Mount Adaptatone as shown in Figure 1.
a. Flat Surface Mounting. Secure unit to mounting
surface using the (4) mounting holes in the
mounting plate on the rear of the box. Use the #10
x 3" (76 mm) wood screws (furnished loose) or
other hardware (not supplied) suitable for the
mounting surface.
b. Rigid Pipe Mounting. Loosen the (4) cover
screws from the signal box and lift off signal box
cover.
NOTE: Cover screws are captive. Do not remove from
cover.
Remove the center knockout in lower wall of box
and mount box to a 1/2” (12.7 mm) conduit pipe
using suitable connector.
2. Wire in accordance with the instructions in “Wiring.”
3. Refer to Figure 14 and Figure 15 and Table 6 and select
desired tones. Set miniature programming switches on
the input board.
For input connected to IN1, set on SW1; IN2, set on
SW2; IN3, set on SW3, and IN4, set on SW4, in order of
priority desired.
4. Adjust volume level, if desired, by turning potentiometer
located on the main board (Figure 14 - Figure 17) and
on voice board (Figure 16).
WARNING: HIGH VOLTAGE is present when product is
energized. High volume may cause harm to personnel in
close proximity.
5. To adjust speaker direction, loosen large star nut
(Figure 1) and turn speaker to the approximate desired
position.
6. Tightly secure the signal box cover using (4) retained
cover screws.
7. Torque signal box cover screws to a minimum of 20 inlbs.
8. Verify operability.
Wiring
1. Install wires through a knockout hole in the bottom of
the box from a raceway that is, with its connections to
the 1/2" conduit knockout hole, approved for the same
degree of protection and enclosure type needed by the
application. Use the provided plastic tie-wrap, on the
barrier to the electronics, to separate incoming power
leads from signal and tone initiating leads, per NEC
(Figure 4 - Figure 6).
WARNING: To prevent fire and shock, wire the Adaptatone
only as described in this installation instruction.
2. Wire as follows referring to Figure 4 - Figure 6. (These
instructions apply to both tone generator and 5532M
series speaker/amplifier, except as noted):
If Edwards Signal Actuator catalog number 5538-4 is
used to manually initiate tones, connect its four
normally-open switches to the Tone Generator as
shown on instructions provided with the Signal Actuator
unit.
a. Connect green and yellow-striped earth-ground
wires to earth-ground and, additionally, on tone
generator, to braid or drain of audio cable in step b.
b. See Figure 5 and Figure 13 - Figure 16. Connect
audio output (+) from the main board of the tone
generator to the AUD (+) terminal on the Speaker /
Amplifier audio coupler board. Use shielded cable
and connect braid or drain to earth-ground wire
lead of 5540 tone generator. Up to 2500
speaker/amplifiers can be so connected in parallel
to a single tone generator.
2 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
c. For the tone generator, select the appropriate
method for wiring to the input board from Figure 7 Figure 12. Connect the tone generator as shown.
d. Connect incoming power to wire leads using a butt
splice or other method listed, certified, or otherwise
approved by local authorities. Leads are both black
for -AQ and -N5 models and are black and white for
-Y6 models.
e. Optional. Connect external 24 VDC battery (not
supplied) in series with separate diode assembly
part 2600010 (supplied) to TB1 terminals 3 and 4
on the main board as shown in Figure 2 and
Figure 3 and marked on the diode assembly.
NOTE: Terminal Block TB1 can be unplugged from the
main board to complete wiring as shown in Figure 2 and
Figure 3.
3. Wire to the 5532B series speaker/amplifier as follows
and referring to Figure 4 - Figure 6 and Figure 17:
If Edwards signal actuator, catalog number 5538-4, is
used to manually initiate tones, connect its four
normally-open switches to the tone generator as shown
on instructions provided with the signal actuator unit.
a. Connect green earth-ground wire of
speaker/amplifier and green and yellow striped
earth-ground wires on tone generator to earthground.
terminals 3 and 4 on the main board of the tone
generator per Figure 2 and Figure 3. Polarities
must be observed.
NOTE: Terminal block TB1 can be unplugged from the main
board of the tone generator to complete wiring.
Maintenance and testing
WARNINGS: To prevent fire, shock and component
damage, NO work, including circuit board removal, should
be performed while the circuit is energized.
NOTE: Any kind of service or maintenance performed
while unit is energized will void the warranty.
Examine the unit semi-annually for accumulation of dirt.
Clean if necessary.
The Adaptatone should be tested annually or as required by
the authority having jurisdiction to ensure continuous
service.
Figure 1: Mounting the Adaptatone
b. Connect audio output (+) from the main board of
the tone generator to the Tone In terminal 9 (+) in
the speaker/amplifier. Connect audio output (-)
from the main board of the tone generator to the
Tone In terminal 10 (-) in the speaker/amplifier. Up
to 2500 speaker/amplifiers can be so connected in
parallel to a single tone generator.
c. For the tone generator, select the appropriate
method of wiring to the input board from Figure 7 Figure 13. Connect the tone generator as shown.
d. For 5532B-AQ, 5532BDV2-AQ and 5532BHV-AQ
models, connect power source to the
speaker/amplifiers at TS2. Polarity must be
observed for DC models.
e. For 5532B-Y6, 5532BDV2-Y6, 5532BHV-Y6, and
5532B-N5 models, connect incoming power to wire
leads from power supply. For -Y6 models using a
DC source, black wire is positive and white is
negative and polarity must be observed. For AC
source, black is line and white is neutral.
f. For tone generator, connect incoming power to wire
leads using a butt splice or other method listed,
certified, or otherwise approved by local authorities.
Leads are both black for -AQ and -N5 models and
are black for line and white for neutral for -Y6
models.
g. Optional. Wire 24 VDC battery backup to TS1-1
and TS1-2 of the speaker/amplifier per Figure 17
and connect 24 VDC battery backup in series with
diode assembly part 2600010 (supplied) to TB1
Figure 2: Terminal block TB1
P/N 3100010 • REV 7 • ISS 04AUG10 3 / 10
Figure 3: Wiring to terminal block TB1 input circuit
Figure 4: Wiring the 5532M series speaker/amplifier
Figure 6: Wiring the 5540MV series tone generator with voice
messaging
Figure 7: Wiring an open collector transistor to tone generator
input board
Figure 5: Wiring the 5540M series tone generator
4 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
Figure 8: Wiring multiple dry relay contacts to 24 V tone
generator input board method 1 (Refer to Applications
Engineering for compatibility with earlier versions of
Adaptatone)
Figure 9: Connecting 24 V input board of tone generator to a
PLC. Refer to Table 5
Figure 10: Wiring multiple dry relay contacts to 24 V tone
generator input board method 2
Figure 11: Wiring multiple dry contacts to 120 V tone generator
input board
P/N 3100010 • REV 7 • ISS 04AUG10 5 / 10
Figure 12: Connecting from a PLC to 120 V tone generator
input board. Refer to Table 5
Figure 13: Wiring audio output of tone generator to
speaker/amplifier audio coupler board
Figure 15: 5540M Series PC board locations
Figure 16: 5540MV Series PC board locations
Figure 14: 5532M Series PC board locations
6 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
Figure 17: Connecting to the 5532B series speaker/amplifiers
P/N 3100010 • REV 7 • ISS 04AUG10 7 / 10
Specifications
Voltage Refer to Table 2 and Table 3
Current Refer to Table 2 and Table 3
Dimensions Refer to Table 4 on page 9
Weight
Tone Generator
Speaker/Amp
Hazardous locations
Ambient temp.
Non-hazardous
locations
Variable ambient
temp
Table 1: Operating temperature codes
Catalog number
5532M-AQ
5532M-N5
5532MHV-AQ
5540M-24AQ
5540M-24N5
5540MV-24N5
5540M-120N5*
5532M-Y6
5532MHV-Y6
5540M-24Y6
5540MV-24Y6
5540M-120Y6*
Table 2: Input board
Catalog number Voltage Current
5540M-24AQ
5540M-24N5
5540MV-24N5
5540M-24Y6
5540MV-24Y6
5540M-120N5
5540M-120Y6
Table 3: Main power
Catalog number Voltage Standby
Tone Generator
5540M-24AQ 24 VDC
5540M-24N5
5540MV-24N5
5540M-24Y6
5540MV-24Y6
6 lb (2.7 kg)
9 lb (4.1 kg)
-31 to 104°F (-35 to +40°C)
-40 to 151°F (-40 to +66°C)
Class II, Div. 2,
Groups F, G
Class I, Div. 2
Groups A, B, C, D
135°C (T4) 100°C (T5)
180°C (T3A) 100°C (T5)
24 VDC 6 mA
120V 50/60 Hz 13 mA
24 VAC 50/60 Hz
120 VAC 50/60 Hz 0.10 A 0.36 A
125 VDC
250 VDC
120 VAC 50/60 Hz
240 VAC 50/60 Hz
Class III, Div. 1 and
2
current
0.10 A
0.10 A
0.10 A
0.02 A
0.10 A
0.10 A
Tone on
current
0.74 A
1.3 A
0.21 A
0.10 A
0.32 A
0.20 A
Catalog number Voltage Standby
current
5540M-120N5
5540M-120Y6
Speaker/Amplifier – Standard Volume
5532M-AQ
5532M-N5
5532M-Y6* 125 VDC
5532B-AQ
5532B-N5
5532B-Y6
Speaker/Amplifier – High Volume
5532MHV-AQ
5532MHV-Y6
5532BHV-AQ
5532BHV-Y6
*5532M-Y6 is suitable for use with 120 / 240 VAC main power input
in conjunction with the 5541M-Y6 Millennium System Master either
for emergency / evacuation, non-fire, or for supplementary fire
alarm control panel accessory applications (see instructions for
5541M-Y6, part 3100471).
120 VAC 50/60 Hz 0.10 0.38 A
125 VDC
250 VDC
120 VAC 50/60 Hz
240 VAC 50/60 Hz
24 VDC
24 VAC 50/60 Hz
120 VAC 50/60 Hz 0.10 A 0.36 A
250 VDC
120 VAC 50/60 Hz
240 VAC 50/60 Hz
24 VDC
36 VDC
24 VAC 60 Hz
24 VAC 50 Hz
120 VAC 60 Hz
120 VAC 50 Hz
125 VDC
250 VDC
120 VAC 60 Hz
240 VAC 60 Hz
120 VAC 50 Hz
240 VAC 50 Hz
24 VDC
24 VAC 50/60 Hz
125 VDC
250 VDC
120 VAC 50/60 Hz
240 VAC 50/60 Hz
24 VDC
36 VDC
24 VAC 60 Hz
24 VAC 50 Hz
125 VDC
250 VDC
120 VAC 60 Hz
240 VAC 60 Hz
120 VAC 50 Hz
240 VAC 50 Hz
0.10 A
0.02 A
0.10 A
0.10 A
0.10 A
0.10 A
0.10 A
0.02 A
0.10 A
0.10 A
0.06 A
0.07 A
0.26 A
0.26 A
0.10 A
0.09 A
0.05 A
0.04 A
0.10 A
0.11 A
0.09 A
0.10 A
0.10 A
0.10 A
0.10 A
0.02 A
0.10 A
0.10 A
0.06 A
0.07 A
0.26 A
0.26 A
0.05 A
0.04 A
0.10 A
0.11 A
0.09 A
0.10 A
Tone on
current
0.20 A
0.10 A
0.31 A
0.20 A
0.74 A
1.3 A
0.21 A
0.10 A
0.32 A
0.20 A
0.69 A
0.84 A
1.36 A
1.36 A
0.29 A
0.29 A
0.16 A
0.10 A
0.29 A
0.23 A
0.29 A
0.22 A
1.5 A
2.3 A
0.39 A
0.19 A
0.56 A
0.34 A
1.51 A
1.98 A
1.86 A
1.86 A
0.25 A
0.23 A
0.62 A
0.33 A
0.62 A
0.33 A
8 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
Table 4: Speaker Amplifier/Dimensions
5531M 5531MHV
A 8 7/8” (225 mm) 11 1/2” (292 mm)
B 8 1/4” (210 mm) 9 3/4” (248 mm)
C 13” (330 mm) 14 1/4” (362 mm)
Table 5: PLC compatibility: PLC output to meet following product input parameters. Refer to Figure 9 and Figure 12.
Catalog number Operating voltage Max. off state leakage
current
5540M-24AQ 24 VDC only 2 mA 740 mA 8 A / 4 mS
5540M-24N5 120 VAC 50/60 Hz 2 mA 360 mA 2.82 A / 4 mS
5540M-24Y6 120 VAC 50/60 Hz 2 mA 320 mA 2.82 A / 4 mS
5540M-120N5 120 VAC 50/60 Hz 5 mA 380 mA 2.82 A / 4 mS
5540M-120Y6 120 VAC 50/60 Hz 5 mA 310 mA 2.82 A / 4 mS
5540MV-24N5 120 VAC 50/60 Hz 2 mA 360 mA 2.82 A / 4 mS
5540MV-24Y6 120 VAC 50/60 Hz 2 mA 320 mA 2.82 A / 4 mS
Input board circuit 24 VDC 2 mA 6 mA --
Input board circuit 120 VAC 50/60 Hz 5 mA 13 mA --
Continuous on current Surge (inrush/duration)
Table 6: Tone programming
Tone SW 4-6 SW 4-5 SW 4-4 SW 4-3 SW 4-2 SW4-1 Description Hex
No Tone OFF OFF OFF OFF OFF OFF 00
Ding-Dong OFF OFF OFF OFF OFF ON Percussive pairs of 700 and 570 Hz tones, each
damped to 0
Warble OFF OFF OFF OFF ON OFF 575 and 770 Hz alternately, 87 ms each 02
Siren OFF OFF OFF OFF ON ON 600 – 1250 Hz up and down sweep in 8 s and repeat 03
Stutter OFF OFF OFF ON OFF OFF Percussive 470 Hz, 83 ms on, 109 ms off 04
Slow Whoop OFF OFF OFF ON OFF ON 600 – 1250 Hz upward sweep in 4 s and repeat 05
Beep OFF OFF OFF ON ON OFF 470 Hz, 0.55 s on, 0.55 s off 06
Chime 1 OFF OFF OFF ON ON ON 700 Hz percussive repeat at 1 Hz 07
Fast Whoop OFF OFF ON OFF OFF OFF 600 – 1250 Hz upward in 1 s and repeat 08
Hi/Lo OFF OFF ON OFF OFF ON 780 to 600 Hz alternately, 0.52 s each 09
Rapid Siren OFF OFF ON OFF ON OFF 600 – 1250 Hz up and down sweep in 0.25 s and repeat 0A
Yeow OFF OFF ON OFF ON ON 1250 – 600 Hz downward sweep in 1.6 s and repeat 0B
Horn OFF OFF ON ON OFF OFF 470 Hz continuous 0C
Air Horn OFF OFF ON ON OFF ON 370 Hz continuous 0D
Dual Tone OFF OFF ON ON ON OFF 470 – 500 Hz, 0.4 to 0.5 s cycle 0E
Chime 2 OFF OFF ON ON ON ON 575 Hz percussive repeat at 1 Hz 0F
Westminster OFF ON OFF OFF OFF OFF Two measures, 411 Hz, 520 Hz, 407 Hz, 312 Hz 10
Three Blind Mice OFF ON OFF OFF OFF ON Four measures, 787 Hz, 714 Hz, 625 Hz, 952 Hz, 333
Hz
Phasor OFF ON OFF OFF ON OFF 416 – 625 Hz up and down sweep in 13 ms and repeat 12
Telephone OFF ON OFF OFF ON ON 570 and 770 Hz alternately, 50 ms each for 1.2s, 1.5s
delay and repeat
Staircase OFF ON OFF ON OFF OFF 440 – 2000 Hz up and down steps, 750 ms delay and
repeat
3 Tone Alert OFF ON OFF ON OFF ON 463 Hz, 641 Hz, and 896 Hz, 200 ms each, 1 s delay
and repeat
RESERVED OFF ON OFF ON ON OFF RESERVED 16
RESERVED OFF ON OFF ON ON ON RESERVED 17
RESERVED OFF ON ON OFF OFF OFF RESERVED 18
RESERVED OFF ON ON OFF OFF ON RESERVED 19
RESERVED OFF ON ON OFF ON OFF RESERVED 1A
01
11
13
14
15
P/N 3100010 • REV 7 • ISS 04AUG10 9 / 10
Tone SW 4-6 SW 4-5 SW 4-4 SW 4-3 SW 4-2 SW4-1 Description Hex
NFPA Whoop OFF ON ON OFF ON ON Three 422 – 775 Hz upward sweeps, 850 ms each, 1 s
3 Pulse Horn* OFF ON ON ON OFF OFF 470 Hz, 3 0.5 s pulses separated by 0.5 s followed by
3 Pulse Air Horn* OFF ON ON ON OFF ON 370 Hz, 3 0.5 s pulses separated by 0.5 s followed by
3 Pulse Dual
Tone*
3 Pulse Chime 2* OFF ON ON ON ON ON 575 Hz, 3 0.5 s pulses separated by 0.5 s followed by
European Police ON OFF OFF OFF OFF OFF 969 Hz and 800 Hz alternately 0.250 s each 20
European Fire ON OFF OFF OFF OFF ON 982 Hz and 864 Hz downward sweep in 0.134 s 21
European Slow
Whoop
European General ON OFF OFF OFF ON ON 1087 Hz for 0.5 s followed by 0.5 s delay and repeat 23
European Toxic ON OFF OFF ON OFF OFF 982 Hz continuous 24
European Police 2 ON OFF OFF ON OFF ON 554 Hz and 440 Hz alternately, 0.8 s each 25
European Stutter ON OFF OFF ON ON OFF 3876 Hz for 0.146 s followed by 0.102 s delay and
European Sweep ON OFF OFF ON ON ON 1315 Hz – 413 Hz downward sweep in 1.17 s and
Telephone 2 ON OFF ON OFF OFF OFF Alternate tones at 567 Hz and 326 Hz 28
Buzzer ON OFF ON OFF OFF ON 1315 Hz and 746 Hz alternating for 0.003 s each 29
Genesis Horn Cont ON OFF ON OFF ON OFF Continuous Genesis horn 2A
Genesis Horn
Temp
Warning 1 ON OFF ON ON OFF OFF 1207 Hz and 493 Hz, alternately 0.002 s each 2C
Warning 2 ON OFF ON ON OFF ON 2336 Hz and 493 Hz, alternately 0.005 s each 2D
Warning 2 Beep ON OFF ON ON ON OFF 0.500 s of 2336 Hz and 493 Hz each alternating for
Caution ON OFF ON ON ON ON 453 Hz for 0.040 s, 235 Hz for 0.020 s, 235 Hz for 0.160
Multi-tone ON ON OFF OFF OFF OFF 376, 357, 352, 382, 355, 375, 384, 375 and 364 Hz
Attention ON ON OFF OFF OFF ON 2232, 4545, 3704, 2777, 4347, 3704, 2500 Hz
High Freq. Steady
Alert
High Freq. Fast
Siren
High Freq. Slow
Siren
DIN PFEER ON ON OFF ON OFF ON Ramp downward from 1336 Hz to 522 Hz in 1.2 s and
NF S 32 001 ON ON OFF ON ON OFF 584 Hz for 0.100 s and 461 Hz for 0.400 s 36
Ode to Joy ON ON OFF ON ON ON 6.45 s of melody followed by 1 s delay and repeat 37
Twinkle Little Star ON ON ON OFF OFF OFF 13.2 s of melody followed by 1 s delay and repeat 38
Dueling Banjos ON ON ON OFF OFF ON 10.84 s of melody followed by 1 s delay and repeat 39
La Cucaracha ON ON ON OFF ON OFF 7.10 s of melody followed by 1 s delay and repeat 3A
Yellow Rose of TX ON ON ON OFF ON ON 19.34 s of melody followed by 1 s delay and repeat 3B
*3 Pulse Tones are for Evacuation Use Only
OFF ON ON ON ON OFF 450 – 500 Hz, 0.4 to 0.5 s cycle, 3 0.5s pulses
ON OFF OFF OFF ON OFF 658 – 1312 Hz upward sweep in 3 s followed by 0.5 s
ON OFF ON OFF ON ON Temporal Genesis horn 2B
ON ON OFF OFF ON OFF 2500 Hz continuous 32
ON ON OFF OFF ON ON 2500 – 3048 Hz up and down sweep in 0.130 s 33
ON ON OFF ON OFF OFF 2500 – 3048 Hz up and down sweep in 0.500 s 34
delay and repeat
1.5 s delay and repeat
1.5 s delay and repeat
separated by 0.5 s followed by 1.5 s delay and repeat
1.5 s delay and repeat
delay and repeat
repeat
repeat
0.005 s followed by 1 s delay
s, 260 Hz for 0.050 s, 260 Hz for 0.1009 s, 235 Hz for
0.050 s
alternately on for 0.050 s
alternately on for 0.003 s
repeat
1B
1C
1D
1E
1F
22
26
27
2E
2F
30
31
35
CAUTION: The use of evacuation signals on this product, that is not specifically listed for fire alarm use, is subject to the approval
of the authority having jurisdiction.
Regulatory information
Edwards
Signaling
10 / 10 P/N 3100010 • REV 7 • ISS 04AUG10
Edwards, A Division of UTC Fire & Security
Americas Corporation, Inc.
8985 Town Center Parkway, Bradenton, FL
34202, USA
Contact information
For contact information, see www.edwardssignaling.com.
Loading...