Description and OperationDescription and Operation
Description and Operation
Description and OperationDescription and Operation
Installation Instructions for Adaptatone Millennium
Remote Audio Signal Converter Series 5510M
InstallationInstallation
Installation
InstallationInstallation
Edwards Remote Audio Signal Converter is intended for
industrial applications where high audible output and
microcomputer reliability are required.
Catalog Series 5510M are UL and cUL Listed as Audible
Signal Appliances for use in the following hazardous
locations.
Catalog Hazardous Temp.
Number Locations Code
5510M-25Y6 Class I, Div. 2, Groups A, B, C, D T4 (135C)
5510M-70Y6 Class II, Div. 2, Groups F, G T5 (100C)
Class III, Div. 1 and 2
The Audio Signal Converter operates from local power.
The 5510M-25Y6 converts 25V RMS audio signal to 10V
RMS for use with the 5532M Adaptatone Speaker/Amplifiers. The 5510M-70Y6 converts a 70V RMS audio signal
to 10V RMS for use with the Edwards 5532M Adaptatone
Speaker/Amplifiers or other 10V RMS applications.
SpecificationsSpecifications
Specifications
SpecificationsSpecifications
Weight ...................................................6 Pounds (2.7 kg)
Hazardous Locations, UL Standard UL1604
Ambient T emp. ................... +41F to +104F (+5C to +40C)
Non-Hazardous Locations
Variable Ambient Temp. .....-40F to +151F (-40C to +66C)
Electrical SpecificationsElectrical Specifications
Electrical Specifications
Electrical SpecificationsElectrical Specifications
Current (A)
Voltage Standby Tone On
Remote Audio Signal Converter
125V DC* 0.10 0.21
250V DC* 0.02 0.10
120V AC 50/60 Hz 0.10 0.32
240V AC 50/60 Hz 0.10 0.20
The Adaptatone may be mounted to any flat surface or
may be used as a freestanding unit mounted to a rigid
pipe. The Adaptatone must be installed in accordance
with the latest edition of the National Electrical Code or
other regulations applicable to the country and locality
of installation and by a trained and qualified electrician.
NOTE: The increased resistance due to long wire runs
needs to be accounted for in sizing wire.
Consult Applications Engineering for details.
CAUTIONCAUTION
CAUTION
CAUTIONCAUTION
During installation, care must be taken so that components
on the printed circuit board are not damaged.
1. Mount Adaptatone as shown in Figure 1.
a. Flat Surface Mounting. Secure unit to
mounting surface using the (4) mounting holes in
the mounting plate on the rear of the box. Use
the #10 x 3" (76 mm) wood screws (furnished loose)
or other hardware (not supplied) suitable for the
mounting surface.
b. Rigid Pipe Mounting. Loosen the (4) cover screws
from the signal box and lift off signal box cover.
NOTE: Cover screws are captive. Do not remove from
cover.
Remove the center knockout in lower wall of box
and mount box to a 1/2" (12.7 mm) conduit pipe
using suitable connector .
2. Install wires through a knockout hole in the bottom
of the box from a raceway that is, with its connections
to the 1/2" (12.7 mm) conduit knockout hole, approved
for the same degree of protection and enclosure type
needed by the application. Use the provided plastic
tie-wrap, on the barrier to the electronics, to separate
incoming power leads from signal and tone initiating
leads, per NEC (Figures 4, 5 and 6).
Figure 1. Adaptatone Mounting
CHESHIRE, CT 203-699-3300 FAX 203-699-3365 (CUST. SERV.) 203-699-3078 (TECH SERV.)
Signal Box
(4) Cover
screws
(4) Collar
gaskets
Raceway and connections
(not supplied)
to the 1/2" (12.7 mm)
knockout hole
(4) #10 x 3" (76 mm)
screws or other hardware
suitable for the mounting surfac
P/N 3100359 ISSUE 2 © 2002
WARNINGWARNING
WARNING
WARNINGWARNING
T o prevent fire and shock, wire the Adaptatone only as
described in this installation instruction.
3. Wire as follows referring to Figures 2 through 5:
a. Connect green and yellow striped earth-ground
wires to earth-ground.
b. See Figure 4. For 5510M-25Y6, connect 25V RMS
audio input (+) to the AUD (+) terminal on the
Audio Coupler Board. Connect 25V RMS audio
input (-) to the AUD (-) terminal on the Audio
Coupler Board.
See Figure 4. For 5510M-70Y6, connect 70V RMS
audio input (+) to the AUD (+) terminal on the
Aduio Coupler Board. Connect 70V RMS audio
input (-) to the AUD (-) terminal on the Audio
Coupler Board.
c. See Figure 4. Connect 10V RMS audio output (+)
to terminal A on the Audio Coupler Board.
Connect 10V RMS audio output (-) to terminal B
on the Audio Coupler Board.
d. Connect incoming power to wire leads using a
butt splice or other method listed, certified, or
otherwise approved by local authorities. Leads
are black for line and white for neutral. See Figure
2.
e. Optional. Connect external 24V DC battery (not
supplied) in series with separate diode assembly
part 2600010 (supplied) to TB1 terminals 3 and 4
on the main board as shown in Figure 7 and
marked on the diode assembly .
NOTE: T erminal Block TB1 can be unplugged from the
main board to complete wiring as shown in
Figure 2.
WARNINGWARNING
WARNING
WARNINGWARNING
T o ensure integrity of the enclosure: Ensure the cover
gasket, part number P-007549-0069, is adhered into
groove at cover perimeter before replacing the signal box
cover.
Ensure that the (4) collar gaskets, part number P-0419300362, are in place on each cover screw before securing the
signal box cover .
When securing cover , start screws by hand, making sure
they are threaded into tapped holes in housing bosses
before securing with a screwdriver . Torque signal box cover
screws to a minimum of 20 in-lbs. This ensures the
required tight fit.
4. Tightly secure the signal box cover using (4) retained
cover screws.
5. Torque signal box cover screws to a minimum of 20
in-lbs.
6. Verify operability.
Maintenance and Maintenance and
Maintenance and
Maintenance and Maintenance and
Ensure that power is disconnected before cleaning inside of
unit.
TT
estest
T
est
TT
estest
WARNINGWARNING
WARNING
WARNINGWARNING
Examine the unit semi-annually for accumulation of dirt.
Clean if necessary .
The Adaptatone should be tested annually or as required
by the authority having jurisdiction to ensure continuous
service.
Main
Board
2
4
1
3
Terminal Block
TB-1
(-)
(-)
Wiring is factory
installed to internal
power supply
(+)
(+)
TB1
24
13
Diode Assembly
2600010
(-)
To optional 24V DC
Battery Backup
(+)
Figure 2. Wiring to T erminal Block TB-1
P/N 3100359 ISSUE 2
PAGE 2