Edwards Signaling 109 Series LED Star-Burst Installation Guide

Installation Instructions for 109 Series

LED Star -Burst

TM

Visual Indicator

Description

The 109 Series Visual Indicator is a UL and cUL listed signaling
appliance in a NEMA 4X and IP65 rated enclosure. The modules
can be panel mounted or conduit mounted.

The visual indicator is normally steady-on and with a contact
closure, the light will flash. The unit is set for the Rapid Star-Burst
flicker flash but with a simple jumper change, can output a 65
flash per minute signal.

The visual indicators are available in red, blue, green, amber or
white.

Specifications

Catalog LED
Number V oltage Current Color

109A-G1 24V DC 0.475 A Amber
109B-G1 24V DC 0.475 A Blue
109G-G1 24V DC 0.475 A Green
109R-G1 24V DC 0.475 A Red
109W-G1 24V DC 0.475 A White
109A-N5 120V 50/60 Hz 0.140 A Amber
109B-N5 120V 50/60 Hz 0.140 A Blue
109G-N5 120V 50/60 Hz 0.140 A Green
109R-N5 120V 50/60 Hz 0.140 A Red
109W-N5 120V 50/60 Hz 0.140 A White

Panel Mounting (Figure 2)

Note: The integrity of the outdoor, NEMA 4X, and IP65 rating on
the panel assembly at the interface with the 109 Series V isual
Indicator relies on the construction and configuration details of
the mounting surface. Installer should evaluate.

1. Place the mounting g asket (supplied) o ver the hole in the
panel and route the signal wires through the gask et and the
hole in the panel.

2. Insert the base through the hole in the panel and scre w the
locking nut (supplied), with the raised locking edge f acing
the mounting surface, onto the base to secure the beacon.

3. Using wire nuts (not supplied), connect the signal's wire leads
as shown in Figure 1 or 2. Polarity must be observed on DC
models.

a. Connect the Red (DC models) or Black (AC models) wire

to hot.

b. Connect the Black (DC models) or White (AC models) to

common.

c. For steady-on applications, trim the yellow wire short

and cap using a wire nut (not supplied). For either Star­Burst flicker flash or standard 65 fpm flash, connect the
yellow wire to hot to activate.

NOTE: On AC models only , the yellow can be connected
to hot, negative or ground to activate the Star-Burst
flicker flash or standard 65 fpm flash)

4. Turn on power and verify that the signal operates properly.

Installation

WARNING

To prevent electrical shock, ensure that power is
turned off before installing the signal.

Conduit Mounting (Figure 1)

1. Thread the 18" (45.7 cm) signal wire leads through either
1/2" (13mm) or 3/4" (19 mm) conduit into an approved conduit
outlet box. (Product is supplied with a double threaded - 1/2"
(13mm) internal and 3/4" (19mm) external - conduit hub.)

2. Using wire nuts (not supplied), connect the signal's wire leads
as shown in Figure 1. Polarity must be observed on DC models.

WARNING

To avoid risk of injury, install lens before energizing
the unit.

To avoid the risk of injury, do not remove or insert
light source when unit is energized.

3. Thread the conduit onto the base of the signal.

Jumper Installation

The 109 Series Visual Indicator is supplied with a default setting
of Star-Burst flicker flash. If a standard flash rate of 65 fpm is
desired, open the unit by removing (4) screws securing the lens to
the base and install jumper on pins 1-2 as shown in Figure 3.

109 Series Star-Burst
Visual Indicator

3/4" (19 mm) NPT
conduit (not supplied)

Red (DC hot) or Black (AC hot)

Black (DC common) or White (AC common)

Yellow (hot to activate
either the Star-Burst flicker flash or
standard 65 fpm flash)

4. Turn on power and verify that the signal operates properly.

Wire nuts
(not supplied)

Figure 1. Conduit Mounting (3/4" Shown)

P/N 3100392 ISSUE 1 © 2002

Maintenance

WARNINGS

To avoid risk of injury, install lens before energizing
the unit.

To avoid the risk of injury, do not start any
maintenance when unit is energized.

Cleaning

The module lens exterior surfaces should be periodically cleaned
with a soft clean cloth using water and a mild detergent to main­tain optimum light visibility. Disconnect power before cleaning.

Light Source Replacement

1. Conduit Mounted Modules: Disconnect wiring and, if
necessary, unscrew base from conduit (Figure 1).

Panel Mounted Modules: Disconnect wiring and remo ve
locking nut securing the base to the panel (Figure 2).

2. Remove (4) screws securing the lens to the base from bottom
of base (Figure 4) and remove lens.

3. Unplug LED light source and plug in new light source.

NOTE: If the color of the LEDs is changed, the lens color

should also be changed to match.

4. Replace lens on base and secure with (4) screws removed in
step 2.

109 Series Star-Burst
Visual Indicator

Locking Nut -

1.3625" OD
(supplied)

Control panel

Yellow (hot to activate

either the Star-Burst flicker flash or

standard 65 fpm flash)

Wire nuts

(not supplied)

Figure 2. Panel Mounting

Gasket
(supplied)

Red (DC hot) or Black (AC hot)

Black (DC common) or White (AC common)

Standard

Flash

Flicker Flash

(Default)

1

2

3

123

P/N 3100392 ISSUE 1

Jumper
(Install on pins 1 and 2
for standard flash)

Figure 3. Installing the Jumper (View of inside bottom of unit)