Edwards Signaling 105DHIST-FJ User Manual

Page 1

Installation Instructions for Cat. No. 105DHIST-FJ

Adverse Location Visual Signals

Description

The 105DHISTC-FJ (clear lens only) visual signal is a heavy duty, reliable, 8 Joule high intensity strobe that is both UL 1971 and CSFM listed for Special Application 20-30V DC Hearing Impaired indoor use in compatible fire alarm systems. See Figure 6 for light output patterns and Table 2 for operating current information.

The 105DHIST*-FJ (*with amber, blue, clear, green, magenta, and red lenses) are Special Application 20-30V DC UL and cUL (General Utility) and CSFM Listed (Misc. Devices/Control Unit Accessories). The units also utilize an 8 joule strobe. See Table 2 for current information.

Table 1. Hazardous Location Ratings

Cat. No. Class Division Group Operating Temperature

105DHIST*-FJ I 2 A, B, C, D T2A (280

I I 2 F, G T3B (165oC, 329oF)

I I I T3B (165

*Insert lens color: A - Amber, B - Blue, C - Clear, G - Green, M - Magenta, R - Red.

Installation

WARNING

To prevent electrical shock, do not connect power until instructed to do so.

Installation must be in accordance with local codes. The lens should be positioned up for outdoor applications.

1. Select a mounting configuration (Figure 5).

NOTE: When mounting using the Cat. No. 105BM mounting

bracket, the Cat. No. 105BX outlet box attachment must also be used as shown in Figure 1.

2. Pull field wiring into the mounting attachment.

3. Install the mounting attachment as follows:

WARNINGS

The 105BX junction box, 105BM mounting bracket and 105PM pipe mount attachments are non-conductive plastic fixtures and do not provide earth-ground continuity when attached to metallic wiring systems.

Therefore

105DHIST series visual signals grounding is not required.

, they are intended for use with the

only

when earth-

These strobes, when assembled in accordance with installation instructions, constitute a UL listed Type 4X enclosure. They are designed for use in industrial applications or in applications where a Type 4X enclosure is required. For General Utility (non-fire alarm) use, all units are UL and cUL Listed for Marine and outdoor visual signaling applications. When assembled in accordance with these instructions, 105 Series visual signals are UL listed for use in Hazardous Locations with Operating Temperatures listed in Table 1.

For specification details, see Tables 2 - 3.

C, 536oF)

C, 329oF)

b. Cat. No. 105BM: Using the four supplied screws, secure

the mounting bracket to Cat. No. 105BX outlet box attachment as shown in Figure 1. Attach the adhesive backed gasket to the top of the 105BM mounting bracket, being careful to line up the holes in the gasket with the mounting holes in the outlet box.

c. Cat. No. 105PM: Install 3/4" (19 mm) conduit. Screw the

pipe mount attachment onto the 3/4" (19 mm) conduit. Attach the adhesive backed gasket to the top of the 105PM pipe mount attachment (Figure 3), being careful to line up the holes in the gasket with the mounting holes in the outlet box.

4. Attach the unit's wire leads to the field wiring as shown in Figure 4.

NOTE: It is not necessary to remove the lens from the Hi-

5. Secure the high intensity strobe base to the appropriate

6. Apply power and verify operability.

Intensity Strobe Base to install the 105DHIST series beacons. See Figures 1, 3 or 4.

mounting attachment using four screws (supplied) as shown in Figure 3.

The 105BX junction box, 105BM mounting bracket and 105PM pipe mount attachments metallic wiring systems end of a run.

a. Cat. No. 105BX: Screw the outlet box attachment to the

mounting surface (Figure 1) using two screws (not supplied) suitable for the surface. Attach the adhesive backed gasket to the top of the 105BX mounting box, being careful to line up the holes in the gasket with the mounting holes in the outlet box.

only

when installed at the

can

be used with

Page 2

Maintenance

The lens should be periodically cleaned using a mild detergent and water on a soft, clean, lint-free cloth.

Light Source Replacement

WARNING

To prevent electrical shock, before starting work on units disconnect power and, for strobe modules wait 5 minutes for stored energy to dissipate.

1. Unscrew the lens from the base.

CAUTION

Do not touch the strobe tube or halogen bulb with bare fingers. Grasp the light source either by the base or using a soft, clean cloth.

2. For Strobe Tube Replacement:

a. Grasp the strobe tube by its base and pull straight up out

of the strobe tube socket (Figure 2).

b. Grasp the new strobe tube by the strobe tube base and

press into the strobe tube socket.

3. Ensure that the clear gasket is on the base with the flared, open end facing down. Screw the lens onto the base.

4. Apply power and verify operability.

Strobe tube

Strobe tube base

Strobe tube

socket

Figure 2. Strobe Tube Replacement

(4) Screws to mount lens to 105PM (supplied)

105HI-L Series Lens

Hi-Intensity Strobe Base

105-L Series Lens

Beacon Base

Gasket

(4) Screws to mount lens to 105BM (supplied)

105HI-L Series Lens

Hi-Intensity Strobe Base

Adhesive backed gasket

105BM Mounting Bracket

Adhesive backed gasket

(2) Screws to mount 105BX to the mounting surface

Mounting Surface

(4) Screws to mount 105BM to 105BX (supplied)

Figure 1. Mounting Cat. No. 105BM Mounting Bracket

Adhesive backed gasket

105PM Pipe Mount Attachment

3/4” (19 mm) Conduit Nipple

Figure 3. Securing the 105DHIST Series Beacon

to the 105PM Pipe Mount Attachment

P/N 3100394 ISSUE 3

Page 3

NOTE: DC polarity of circuit shown in supervisory state (signal inactive). Circuit polarity to reverse to activate signal. Electrical supervision requires wire run to be broken at each device. Device for constant input voltage. Do not connect to “coded” or pulsating voltage.

(-)

From Power Source

Previous Signaling Device

(+)

Red

105DHISTC-FJ 105DHISTC-FJ

Black

(-)

(+)

Red

Black

(-)

(+)

Red

Black

(-)

(+)

Red

Black

(-)

KEY:

Light symbol -

Wire nut symbol -

End-of-Line Resistor, when required with supervised system

(+)

NOTE: For non-fire alarm stand-alone use tie the two red leads together and tie the two black leads together.

Figure 4. Wiring Diagram for the 105DHIST-FJ Series

Table 2. 105DHIST-FJ Series Electrical Specifications

Operating Current* Initial Surge Inrush Current Repetitive Surge Current

Voltage** RMS Current (A) Mean Current (A) Current (A) Time (mS) Current (A) Time (mS)

20V DC 1.08 0.84 2.70 1.10 2.24 450 24V DC 0.95 0.69 2.97 1.13 2.21 400 28V DC 0.85 0.66 3.06 1.24 2.16 381 30V DC 0.83 0.64 3.14 1.27 2.14 360

*Use the operating current to establish the wire gauge and standby power requirements. Consult the control unit manufacturer to determine surge and peak current effects and maximum number of strobes on the system.

**CAUTION: To prevent damage to the visual signal's internal circuit and to assure its continued proper functioning, DO NOT operate the unit outside of the Special Application voltage range of 20-30V DC.

Mounted on a Cat. No. 105PM Pipe

Mount Attachment

Mounted on a Cat. No. 105BX Outlet

Box Attachment

Mounted on a Cat. No. 105BM

Mounting Bracket with the Cat. No. 105BX Outlet Box

Attachment

Figure 5. Mounting Configurations

105DHIST Series

P/N 3100394 ISSUE 3

Page 4

Product Light UL Limit as % of 0 axis rating

12 %

Intensity as %

of UL 0 axis

rating

Intensity

Angle

(Cd) 90 94.4 12 % 363 % 85 58.9 12 % 227 % 80 30.9 12 % 119 % 75 22.2 13 % 85 % 70 21.6 15 % 83 % 65 23.8 16 % 92 % 60 26.6 18 % 102 % 55 28.6 22 % 110 % 50 29.4 27 % 113 % 45 29.6 34 % 114 % 40 29.2 46 % 112 % 35 29.8 65 % 115 % 30 32.2 90 % 124 % 25 31.7 90 % 122 % 20 28.5 90 % 110 % 15 27.0 90 % 104 % 10 24.2 90 % 93 %

5 25.8 90 % 99 % 0 26.0 100 % 100 %

-5 25.8 90 % 99 %

-10 24.2 90 % 93 %

-15 27.0 90 % 104 %

-20 28.5 90 % 110 %

-25 31.7 90 % 122 %

-30 32.2 90 % 124 %

-35 29.8 65 % 115 %

-40 29.2 46 % 112 %

-45 29.6 34 % 114 %

-50 29.4 27 % 113 %

-55 28.6 22 % 110 %

-60 26.6 18 % 102 %

-65 23.8 16 % 92 %

-70 21.6 15 % 83 %

-75 22.2 13 % 85 %

-80 30.9 12 % 119 %

-85 58.9 12 % 227 %

-90 94.4

363 %

Wall Mount, Dome Horizontal, Vertical and Horizontal Viewing Plane

Intensity (Cd)

UL Rating

0o axis looking at

end of dome

UL 1971 Hearing Impaired: 26 cd wall rating

UL 1638 General Utility: 26 cd at 0o axis

100.0

90.0

80.0

70.0

60.0

50.0

40.0

30.0

20.0

10.0

0.0

-55

-60

-65

-70

-75

-80

-85

-90

-5

-10

-15

-20

-25

-30

-35

-40

-45

-50

Product Light UL Limit as % of 0 axis rating

UL Limit as % of 0 axis rating

Intensity as %

of UL 0 axis

rating

Product Light Intensity as % of UL 0 axis rating

Intensity

Angle

(Cd) 90 0.8 3 % 85 0.8 3 % 80 1.8 7 % 75 3.7 16 % 70 4.7 19 % 65 6.9 29 % 60 7.5 31 % 55 7.7 32 % 50 8.2 34 % 45 9.5 39 % 40 11.4 48 % 35 14.1 59 % 30 14.8 62 % 25 19.0 79 % 20 21.6 90 % 15 22.1 92 % 10 30.8 129 %

5 58.8 245 %

0 94.2 100 % 393 %

-5 58.8 90 % 245 %

-10 30.8 90 % 129 %

-15 22.1 90 % 92 %

-20 21.6 90 % 90 %

-25 23.8 90 % 99 %

-30 26.6 90 % 111 %

-35 28.5 65 % 119 %

-40 29.4 46 % 122 %

-45 29.5 34 % 123 %

-50 29.1 27 % 121 %

-55 29.8 22 % 124 %

-60 32.2 18 % 134 %

-65 31.6 16 % 132 %

-70 29.2 15 % 122 %

-75 27.0 13 % 112 %

-80 24.2 12 % 101 %

-85 25.7 12 % 107 %

-90 26.0 12 % 108 %

Intensity

Angle

(Cd) 90 94.4 25 % 363 % 85 58.9 25 % 227 % 80 30.9 30 % 119 % 75 22.2 30 % 85 % 70 21.6 35 % 83 % 65 23.8 35 % 92 % 60 26.6 40 % 102 % 55 28.6 45 % 110 % 50 29.4 55 % 113 % 45 29.6 75 % 114 % 40 29.2 75 % 112 % 35 29.8 75 % 115 % 30 32.2 75 % 124 % 25 31.7 90 % 122 % 20 28.5 90 % 110 % 15 27.0 90 % 104 % 10 24.2 90 % 93 %

5 25.8 90 % 99 % 0 26.0 100 % 100 %

-5 25.8 90 % 99 %

-10 24.2 90 % 93 %

-15 27.0 90 % 104 %

-20 28.5 90 % 110 %

-25 31.7 90 % 122 %

-30 32.2 75 % 124 %

-35 29.8 75 % 115 %

-40 29.2 75 % 112 %

-45 29.6 75 % 114 %

-50 29.4 55 % 113 %

-55 28.6 45 % 110 %

-60 26.6 40 % 102 %

-65 23.8 35 % 92 %

-70 21.6 35 % 83 %

-75 22.2 30 % 85 %

-80 30.9 30 % 119 %

-85 58.9 25 % 227 %

-90 94.4 25 % 363 %

Wall Mount, Dome Down, Vertical Viewing Plane

Intensity of Horizontal plane is same as 0o angle of vertical, 360o around

100.0

90.0

80.0

70.0

60.0

50.0

40.0

30.0

20.0

10.0

0.0

axis looking at

Intensity (Cd)

UL Rating

side of dome

UL 1971 Hearing Impaired: 24 cd wall

UL 1638 General Utility: 94 cd at 0o axis

Ceiling Mount

Intensity (Cd)

UL Rating

-90

-85

0o axis looking at

end of dome

UL 1971 Hearing Impaired: 26 cd ceiling

100

-80

-75

-70

-65

-60

-55

-50

-45

-40

-35

-30

-25

-20

-15

-10

-5

-85

UL 1638 General Utility: 26 cd at 0o axis

Figure 6. Light Output Patterns for 105DHISTC-FJ (Unit with clear lens only)

-5

-10

-15

-20

-25

-30

-35

-40

-45

-50

-55

-60

-65

-70

-75

-80

P/N 3100394 ISSUE 3

Page 5

Table 3. Specifications

Cat. No. T VsgnitaRepy oltage Current

3.625”

(92 mm)

4.75”

(121 mm)

6.75”

(171 mm)

4.5”

(114 mm)

4.5”

(114 mm)

2.25”

(57 mm)

105PM Pipe Mount Attachment 105BM Mounting Bracket

*Insert lens color: A - Amber, B - Blue, C - Clear, G - Green, M - Magenta, R - Red.

Strobe tube life @ operating power to 75% eciency.

105DHIST*-FJ High Intensity 800,000 Peak Cd Table 2 Table 2

105BX Outlet Box Attachment

Mo dul e La mp

8 Joule Strobe 3,000 Hours

4.5”

(114 mm)

2”

(51 mm)

5.25”

(133 mm)

6”

(152 mm)

4.5”

(114 mm)

(use with 105BX)

4.5”

(114 mm)

Contacting Edwards:

Phone: (203) 699-3000

E-Mail: techsupport@edwards-signals.com

customerservice@edwards-signals.com

Website: http://www.edwards-signals.com

P/N 3100394 ISSUE 3

Edwards Signaling 105DHIST-FJ User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual