Edwards Signaling 102 Mounting Flange User Manual
Installation Instructions for Mounting Flange Kit
for use with the 102 Series Triliptical
TM
Stackable Status Indicator
Contents
A (1) 102PMF pipe mount flange
B (4) #10-24 x 1" (25 mm) pan head, phillips screws
C (4) o-rings
D (1) mounting gasket
E (4) external tooth #10 star washers
F (4) #10-24 hex nuts
G (1) green #10-16 x 3/8" pan head, thread forming ground
screw
H (1) brass terminal cup washer
Accessories
102MP-4 4" Extension Pipe
102MP-10 10" Extension Pipe
102MP-15 15" Extension Pipe
Description
The Edwards Triliptical Stackable Beacon Lighting System is a
unique audible-visual signaling device that can contain up to 5
light modules and either a single or multiple tone module in a
single "stack."
The pipe mount flange, 102PMF, and one of the three extension
pipes (sold separately) allow the status indicator to be raised above
the mounting surface for increased visibility. It can be used with
either the Cat. No. 102TBS or Cat. No. 102PMBS mounting bases.
Installation
Installation must be in accordance with the latest edition of the
National Electrical Code and other governing standards and codes
for standard installation.
1. Panel mount the 102PMF pipe mount flange (A) as follows.
a. Using the supplied gasket (D) as a guide, mark the four
mounting holes and the center clearance hole on an
appropriate surface.
b. Punch the four mounting holes. Punch the wiring
clearance hole in the mounting surface to be sufficiently
larger than that in the gasket to ensure the wiring
insulation is protected from abrasion by the gasket
(without interfering with the mounting screw holes), or
provide other appropriate wire insulation abrasion
protection as needed.
c. Screw the pipe extension (purchased separately) into the
mounting flange.
d. Ground the flange by pulling the ground wire through
the mounting surface clearance hole and center hole of
the gasket. Connect earth ground to the bottom of the
base mount flange using the ground screw (G) and wire
retention terminal cup washer (H).
e. Pull the remaining field wiring through center clearance
hole of mounting surface, center hole of the gasket, pipe
mount flange and extension pipe.
f. Align the mounting gasket (D) and flange (A) on the
panel. Secure using (4) #10-24 x 1" (25 mm) pan head
screws (B), (4) external tooth #10 star washers (E) and
(4) #10-24 hex nuts (F). See Figure 1.
2. Mount the base as follows.
a. Install either Cat. No. 102TBS or Cat. No. 102PMBS
base on 3/4" (19 mm) conduit (not supplied). Pull field
wiring through conduit entrance hole.
3. Connect field wiring as instructed in the installation
instructions, P/N 500002, provided with themounting base.
4. Assemble the stackable beacon lighting system as described
in the installation instructions provided with either the
mounting base or the appropriate components.
WARNINGS
To prevent electrical shock, do not connect power
until instructed to do so.
To prevent abrasion of wiring insulation, ensure
that wire passage holes are adequately protected.
CHESHIRE, CT 203-699-3000 F AX 860-677-7746
P/N 500034 ISSUE 2 © 1998
C
(4) o-rings
(4) #10-24 x 1" (25 mm)
B
pan head screws
A
Cat. No. 102PMF
Pipe mount flange
H
Wire retention
terminal cup washer
G
#10-16 x 3/8"
Pan he a d , thread f orm i ng,
ground ( ) screw
Mounting g a s ket
#10-24 Hex nut
P/N 500034 ISSUE 2
D
E
External tooth
#10 Star washer
F
Figure 1. Mounting Kit Assembly
Loading...