EDUP WAR-54M-01 User Manual
Questions? Call toll-free at 1-800-247-7285
1
Connect the Gateway to a Computer
Step 3 Plug the smaller end
of the
Power Cord into the
Black Port on the back of the
Gateway.
Step 4 Plug the larger end of
the
Power Cord into a Power
Outlet
.
Step 1 Get the Wireless DSL
Gateway
from your DSL
Quick Start Kit and take it out
of the bag.
Step 2 Get the Black Bag and
remove the
Power Cord from
the bag.
Wireless DSL Gateway
Power Cord
Power Cord
Black Port
Step 10 Get the Green DSL
Cable
out of the Black Bag.
Step 11 Plug one end of the
Green Cable into the Green
Port
on the back of the
Gateway.
Questions? Call toll-free at 1-800-247-7285
Step 5 Confirm the Power
Light
on the Gateway is Green.
Power Light on Wireless DSL Gateway
Step 13 Confirm that the
Power and DSL Lights are
solid
Green.This may take up
to 30 seconds.
Power & DSL Lights on Wireless DSL Gateway
Step 6 Get the Yellow Cable.
Step 7 Plug one end of the
Yellow Cable into the Yellow
Port
on the back of the
Wireless DSL Gateway.
Questions? Call toll-free at 1-800-247-7285
Step 8 Plug the other end
of the
Yellow Cable in the
Ethernet Port on the back of
the computer.
An
Ethernet Port looks similar
to a regular Phone Jack,but is
slightly larger.
Note: If the Ethernet Network Light does NOT turn green,make sure the Yellow
Cable is properly connected on both ends.
Step 9 Confirm that the
Ethernet light on the
Gateway is
Green. This may
take a few moments.
Ethernet Light on Wireless DSL Gateway
Step 12 Plug the other end of
the
Green Cableinto the Phone
Jack
closest to your computer.
Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
Note:If the DSL Light continues to blink,make sure you received notification from
your DSL Service Provider that your DSL service is On.O ther wise,contact your
DSL Service Provider immediately.
Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
Before proceeding,make sure you have received notification
from your phone company that your DSL line is active.
Note:
If you have a Macintosh Computer,see section 6,“Setup a Macintosh
Computer,”at the end of this Quick Star t Guide.
Step 1 Open a Web browser
(Netscape Navigator or Internet
Explorer,for example).In the
address bar,enter
http://192.168.0.1,then press
Enter on the keyboard.
Step 2 The “Main Menu”screen
appears.Select
Setup/ Configuration.
Step 3 Click Non-Windows
Setup
in the left-hand column
of the “Set Up/Configuration”
screen.
Step 4 The “Actiontec DSL Modem
Setup Page”screen appears.
Follow the onscreen instructions.
Have your Internet Service
Provider
(ISP) Worksheet handy
and use it to fill in the text boxes
in the
Actiontec DSL Modem
Setup Page.
If you have not received your ISP
Worksheet,contact your ISP. The
Worksheet is provided separately
from this kit by your ISP.
Step 5 Click Save and Restart at the bottom of the Actiontec
DSL Modem Setup Page to save your changes.
The Wireless DSL Gateway is now configured and ready for
use.For more information regarding technical support,please
review the Start Here Guide.
If you received a Block of IP addresses from your Internet Service
Provider,follow the instructions in Section 4 of this Guide,
“Configure a Block of IP Addresses.”Other wise,go to Section 5,
“Configure a Single IP Address.”
Security Notice
Don’t be a victim! Secure your DSL service from unwanted
intrusions.Please refer to the Security section of your User
Manual for more information regarding network security.
2
Install the Phone Filters
Step 1 Unplug your T elephones
(or other devices) from their
current
Phone Jacks.
Step 2 Open the Clear Bag
and remove the Phone Filters
from the bag.
What are Phone Filters? Phone Filters separate the DSL signal
from the voice signal,allowing you to talk on the telephone
and be online at the same time.
All Devices with the same phone number as your DSLLine
require Phone Filters. This includes telephones,fax machines,
caller ID boxes,and answering machines.
Caution: Do Not unplug the Green Cable from the Phone Jack near your Computer.
Note:The number and type of Phone Filters included in this kit may vary.
Step 3 Plug a Phone Filter
into every Phone Jack in your
house with the same phone
number as your DSL Line,and
a telephone (or other device)
connected to it.
If you need additional Phone
Filters,contac t your DSL
Service Provider.
Note:If you have a wall-mount telephone,you must install the Wall-Mount Phone
Filter.For all other telephones or other devices,use the small Phone Filters.To
install a Wall-Mount Phone Filter, see “Installing a Wall-Mount Phone Filter,”below.
Step 4 Plug one end of the Phone
Cord
into the Phone Filter and
keep the other end attached to
the telephone (or other device).
Caution:Do Not connect a Phone Filter into the Phone Jack near your Computer
(the Phone Jack into which your Green Cable is plugged).
To Install a Telephone next to your Computer:
Step 1 Find the Phone Cord
connected to the T elephonenext to
your Computer.Unplug this Phone
Cord from the Phone Jack it is
currently plugged into (you may
have already unplugged the cable
during the modem installation
process).Keep the other end
connected to the Telephone.
Phone
Jack
Phone
Cord
Note: Do Not unplug the Green cable from the Phone Jack near your computer.
Step 2 Plug the Phone Cord
into the Port marked “Phone” on
the back of the Gateway.
Do Not
plug the Phone Cord into the
back of your Computer.
Make sure you have connected
your Phone to the Gateway
exactly as shown in the picture to
the right.
Power
Outlet
Power
Cord
Note:The phone port on the Gateway includes a built-in microfilter. As a result,
no additional filter is needed.
Phone
Port
DSL Cable
1) Remove the wall-mount telephonefrom the wall jack.
2) Open the top and bottom toggles until they snap into the
open position.
3) Push the Wall-Mount Phone Filter into the wall jack,fully
inserting the plug on the back of the filter into the wall
jack opening.
4) Push the toggles back into the closed position until they
lock on the studs of the wall jack.
5) Reattach the telephone to the Wall-Mount Phone Filter.
Installing a Wall-Mount Phone Filter
3
Configure the Gateway
Flip this Quick Start Guide over to continue
If you are installing DSL service
and have a monitored home
security alarm,
Do Not continue
with this installation process.We
recommend calling your DSL
Service Provider for a technician
installation,or contacting your
security system provider for
further details.Please refer to
the Security section of the User
Manual for more information.
Yellow Port
Green Port
Yellow Cable
Green
Cable
QwstARK RedQS.qxd 12/2/03 11:20 AM Page 1
Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
1
Connect the Gateway to a Computer
For All Users (Including Non-Windows Users)…
•
Wireless DSL
Gateway
•
Black Bag
•
Yellow Cable
•
Clear Bag
NEXT
Quick Start Guide
Wireless DSL Gateway
Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
Before connecting a Wireless Wireless DSL Gateway to a
Macintosh computer, the computer must be set up for networking.Use the following procedure.
Step 1 Click the Apple in the
upper right corner of the menu
bar to reveal the
Apple Menu.
Step 2 From the Apple Menu,
click
Control Panels.
Step 3 From the Control
Panels
menu,click TCP/IP.
Step 4 When the TCP/IP
window appears,select Edit
from menu bar,then select
User Mo d e .
Step 5 When the User Mode
window appears,select
Advanced,then click OK.
Step 6 In the TCP/IP window,
select
Ethernet from the
Connect via pop-up menu.
Step 7 Select Using DHCP
Server
from the Configure
pop-up menu.
Step 8 Ensure the Use 802.3
option is Not checked.
Step 9 Click Options,and when
the
TCP/IP Options window
appears,select
Active.Make
sure the
Load only when
needed
option is Not checked,
then click
OK.
Step 10 Close the TCP/IP
window and when prompted
to save changes,click
Save.
Step 11 Restart the Computer.
The Computer is now set up
for networking.
Note:The procedure below is for the Macintosh operating systems version 9.2.2
and below.For computers running Macintosh OS X,see the User Manual.
Note: MSN Users with MAC OS-X and Later: In order to complete your MSN
installation and activate your MSN Account,insert the disk labeled “Windows
Users:Put this CD in FIRST ”.
• Access your CD-ROM drive.
• Open the MSN for MAC folder.
• Double click on the “MSN for MAC OS X.dmg”file.
• Follow the instructions provided in the installation software.
Congratulations!You have successfully installed your Wireless
DSL Gateway.You can now access the Internet at high speed.
This Quick Start Guide will walk you through the
easy steps to set up your Wireless DSL Gateway.
During this process,we’ll show you how to:
Step 1 Click Setup in the top
menu.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration”screen.
Step 3 Click Begin Advanced
Setup
in the next screen.
Step 4 Click WAN IP Address
in the left-hand column of the
“Configuring the Advanced
Settings”screen.
Step 5 Make sure the circle
next to
Obtain an IP Address
through PPPoA
is selected.
Step 6 Check the box next to
Unnumbered Mode.
Step 7 Enter the
information for the
Unnumbered IP Address.
Click
Next.
Step 8 Enter your User Name
and Password.
Step 6 Enter your User Name,
Password
and Static IP address.
Step 9 Click Save and Restart
in the left-hand column.
Step 7 Click Save and Restart
in the left-hand column.
Step 1 Click Setup in the top
menu.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration”screen.
Step 3 Click Begin Advanced
Setup
in the next screen.
Step 5 Click the circle next to
the type of WAN IP Address
you have,then click
Next.
Step 4 Click WAN IP Address
in the left-hand column in the
“Configuring the Advanced
Settings”screen.
You will need the following items from your
Actiontec Quick Start Kit:
4
Configure a Block of IP Addresses
5
Configure a Single IP Address
6
Setup a Macintosh Computer
Part No.:0530-0427-001
Note:The information required to configure a single IPaddress is provided by
your ISP.If this information has not been provided,contact your ISP.
Note:The information required to configure a block of IPaddresses is provided
by your ISP.If this information has not been provided,contact your ISP.
2
Install the Phone Filters
3
Configure the Gateway
4
Configure a Block of IP Addresses
5
Configure a Single IP Address
6
Setup a Macintosh Computer
QwstARK RedQS.qxd 12/2/03 11:20 AM Page 2
Loading...