Edsal URWB-3 User Manual

Heavy Duty 3’

MODEL NUMBER

1 Drawer Work Bench

URWB - 3

URWB

URWB

URWB

Top Back Post Right
Top Back Post Left
Bottom Back Post
Front Post
Braces
Beams
Left Top Support Extension
Right Top Support Extension
Top Shelf Flat Beam
Left Drawer Mount
Right Drawer Mount
Left Drawer Slide
Right Drawer Slide
Front Drawer Shelf Brace
Back Drawer Shelf Brace
Steel Peg Board
Laminate Shelves
Laminate Drawer Shelf
Laminate Top Shelf
Nuts, Bolts, Washers
Handle
Wall Anchor
Post Connector

-

3 3 Shelf 1 Drawer

-

3 3 Shelf 1 Drawer

-

3 3 Shelf 1 Drawer

Description

-

72”h x 18”d x 36”w

-

72”h x 18”d x 36”w

-

72”h x 18”d x 36”w

Qty.

1
1
2
2
4
4
1
1
2
1
1
1
1
1
1
2
2
1
1
8
1
2
1

Part Number

RUPTSPR3702S

RUPTSPL3702S

RUPTSP3802S

RUPT3502S

RUBE1702
RUBE3502

RWTE0902L

RWTE0902R

RMBE3502

SVRWDM1705L

SVRWDM1705R

SVRWDS1403L
SVRWDS1403R
SVRWDB3102F
SVRWDB3102B

SPGBD1536
RPB21836LM
RPB31011LM

RPB2369LM

HDL1000

NB8

N/A
N/A

Part Size

36”
36”

38 3/8”

35”
18”
36”

9”
9”

36”
N/A
N/A
N/A
N/A

31”

31”

15 3/4” x 36”

18” x 36”
11” x 31”

9” x 36”

N/A
N/A
N/A
N/A

Required Tools

Required Tools

Required Tools

- Rubber Mallet

Safety Instructions

Safety Instructions

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.

General Instructions

General Instructions

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel

free to contact our Edsal manufacturing facility at, [phone] and request customer service. We can

also be reached on the internet at the following email address : [e-mail].

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

Consumer Products Division
Edsal Manufacturing Company

4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com

MADE IN CHINA

Assembly Instructions for URWB

Assembly Instructions for URWB

Assembly Instructions for URWB

-

3

-

3

-

3

Step

Post are directional.
The slot must point
down.

Skip Hole From Bottom

1

36” Top
Right Back Post

Right Side
Drawer Mount

38 3/8”
Bottom Post

Take one (1) 38 3/8” bottom back post (top end has a
half slot hole), and (1) 36 top right back post (top has
slot holes, bottom has rivets) and create a coupled back
post. Take one (1) 18” brace (shelf ledge up), and one
(1) 35” front post and attach the rivets of the brace to
the top two (2) holes of the front post. Take the coupled
back post and attach the opposite rivets to the holes so
the brace is level. Tap brace down to seat. Attach the
bottom 18” brace to the front post skipping one (1)
hole from the bottom, and the opposite end level to
the coupled back post. Tap brace down to seat. Take
one (1) drawer mount and insert the rivets one (1) slot
hole below the 18” top brace on both ends, and tap to
seat. Repeat steps for the opposite end assembly.

18” Brace

35” Front Post

Tap Lightly

Shelf Ledge Up

Top
Right
Back
Post

(36”)

Bottom
Back
Post

(38 3/8’”)

Step

36” Flat Beam
(Bend Down)

2

Top Support
Extensions

36” Beams
(Ledge Up)

Take Four (4) 36” beams with the shelf ledge facing
up, and attach two (2) even with the end assembly's
bottom braces, and two (2) even with the braces at the
top. Install one (1) back 36” Flat beam with the bend
facing down, to the top holes of the top back posts.
Take the two (2) support extensions, and Install one (1)
36” Flat beam with the bend facing down, to the front
holes of the top support extensions to create the top
shelf assembly. Take the support extension’s rivets of
the assembly, and Install the top shelf assembly even
with the rivets of the 36” back Flat beam of the unit.

36” Flat Beam
(Bend Down)

Step

Two (2) Piece
Peg Board

(Bolts at the post)

3

Right Side
Drawer Slide

Peg Board
Fastens at
These Points

(opposite side also)

Black Flat Drawer Brace (rear)

(Bend Down)

Silver Flat Drawer Brace (front)

(Bend Down)

Place the two (2) halves of the peg board to the inside of the
back post of the work bench. Align the holes of the peg
board to holes on the back post. Fasten using the nuts and
bolts provided.

and one (1) black 31” Flat drawer braces. With the bend
facing down, insert the rivets of the black brace into the slot
and half slot holes located on the back end of the drawer
slides. Insert the laminated shelf, and install the silver front
drawer brace to the front of the drawer slides. Install the
drawer assembly to the drawer mounts slides of the unit.

Take two (2) drawer slides, one (1) silver,

Laminate
Shelf

Step

4

Install the handle to the front drawer brace, and add the
laminate shelves to the top shelf, bottom shelf, and work
surface to finalize the assembly of the workbench. Op­tional anchor hardware is supplied with this unit so the
unit can be fastened to a wall if necessary.