Edsal MR841848 User Manual

Heavy Duty Steel Shelving
B - Beams
A - Braces
E - Woodboard Shelf
MODEL NUMBER
MR - 841848
C - Top Post 36”
MR
-
841848 6 Shelf
MR
-
841848 6 Shelf
MR
-
841848 6 Shelf
Description
A - Braces B - Beams C - Top Post D - Bottom Post E - Woodboard
Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care when working with metal parts.
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
Qty.
12 12
4 4 6
-
84”h x 18”d x 48”w
-
84”h x 18”d x 48”w
-
84”h x 18”d x 48”w
Part Number
RMBE1702
RMBE4703 RUPT3602S RUPT4802S
RPB21848
Part Size
17 5/32” 47 5/32”
36” 48”
47 29/32”
D - Bottom Post 48”
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Muscle Rack manufacturing facility at, (773) 475-3000 and request customer service.
We can also be reached on the internet at the following email address : customerservice@edsal.com.
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division Edsal Manufacturing Company
4400 South Packers Avenue Chicago, IL 60609 www.edsal.com
Assembly Instructions for MR
Assembly Instructions for MR
Assembly Instructions for MR
-
841848
-
841848
-
841848
Step
1
Figure A
Brace
Assemble two (2) 48” bottom post with one (1) brace. Skipping one slot from the bottom of the post (see figure A), place rivets into post with the slot pointing down and the shelf ledge of the brace facing up (see figure B). Tap lightly to seat rivets. Re­peat with two (2) 48” bottom post and one (1) brace. Assemble the two (2) end units with two (2) beams (see figure C). Skip one hole from the bottom of post, tap lightly to seat rivets.
Figure B
Note: Post are directional. The slot must point down.
48” Bottom Post
Figure C
Figure C
Tap Lightly
Shelf Ledge
Post Slot Points Down
Beam
Step
2
Woodboard Shelves
Start by adding a woodboard shelf to the level previously built, then continue working by adding the second and 3rd level using four (4) beams and four (4) braces in the post slots, and adding a woodboard shelf to each level as it is assembled. Again place the rivets of the beams and braces into the post slots with the shelf ledge facing up and tap lightly to seat the rivets.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
Step
Note: Post are directional. The slot must point down.
3
36” Top
Figure D
Tap Lightly
Bottom Post
Assemble the top post to the bottom post by using four (4) 36” top post, two (2) beams and two (2) braces. One (1) rivet from each beam and brace must be placed in the top hole of the 48” bottom post, and the bottom hole of the 36” top post (see figure D). After all beams and braces are in place, tap lightly to properly seat the rivets.
Post
Slot Down
Step
4
Woodboard Shelves
Add a woodboard shelf to the previously built level, then continue by adding the fifth and sixth level to the unit using two (2) beams and two (2) braces per level. Tap lightly to properly seat the rivets and add the final wood­board shelves to the unit.
Loading...