Edsal MR1848 User Manual

Maxi Rack
Boltless Shelving

MODEL NUMBER (s)

MR185 - MR245 - MR1848

MR

-

185 5 Shelf

MR

-

185 5 Shelf

MR

-

185 5 Shelf

Description

A - Beams
B - Braces
C - Post
D - Wood Shelf

-

72”h x 18”d x 36”w

-

72”h x 18”d x 36”w

-

72”h x 18”d x 36”w

Qty.

Part Number

10
10

8
5

RMBE3502
RMBE1702

RUPT3602S

RPB21836

Part Size

35 5/32”
17 5/32”

36”

35 29/32”

B - Braces

MR

-

245 5 Shelf

MR

-

245 5 Shelf

MR

-

245 5 Shelf

Description

A - Beams
B - Braces
C - Post
D - Wood Shelf

D - Wood Shelf

-

72”h x 24”d x 48”w

-

72”h x 24”d x 48”w

-

72”h x 24”d x 48”w

Qty.

Part Number

10
10

8
5

RMBE4702
RMBE2402

RUPT3602S

RPB22448

A - Beams

Part Size

47 5/32”
23 5/32”

36”

47 29/32”

MR

MR

MR

Description

A - Beams
B - Braces
C - Post
D - Wood Shelf

-

1848 5 Shelf

-

1848 5 Shelf

-

1848 5 Shelf

Qty.

C - Post

-

72”h x 18”d x 48”w

-

72”h x 18”d x 48”w

-

72”h x 18”d x 48”w

Part Number

10
10

8
5

RUBE4702
RUBE1702

RUPT3602S

RPB21860

Part Size

47 5/32”
17 5/32”

36”

47 29/32”

Safety Instructions

Safety Instructions

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible
safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not included. Do not
use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE UNIT, OR
USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom. Use care
when working with metal parts.

General Instructions

General Instructions

General Instructions

Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the
beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood be­tween the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free
to contact our Maxi Rack manufacturing facility at, [phone] and request customer service. We can also

be reached on the internet at the following email address : [e-mail].

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

Consumer Products Division
Edsal Manufacturing Company

4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com

Assembly Instructions for MR185

Assembly Instructions for MR185

Assembly Instructions for MR185

-

MR245

-

MR245

-

MR245

-

MR1848

-

MR1848

-

MR1848

Step

1

Figure A

Post

Brace

Assemble two (2) post with one (1) brace. Skipping one slot
from the bottom of the post (see figure A), place the rivets
into post with the slot pointing down, and with the shelf ledge
of the brace facing up (see figure B). Tap lightly to seat riv­ets. Repeat with two (2) post and one (1) brace. Assemble
the two (2) post units with two (2) beams (see figure C). Skip
one hole from the bottom of post, tap lightly to seat rivets.

Figure B

Note:
Post are
directional.
The slot
must point
down.

Figure C

Figure C

Tap Lightly

Shelf Ledge

Post Slot Points Down

Beam

Step

2

Wood Shelf

Start by adding a wood shelf to the level previously built,
then continue working by adding the second level using
two (2) beams and two (2) braces in the post slots of
your desired location. Again place the rivets of the
beams and braces into the post slots with the shelf
ledge facing up and tap lightly to seat the rivets.

IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.

IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.

IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.

Step

Note:
Post are directional. The slot
must point down.

3

Top

Figure D

Tap Lightly

Bottom
Post

Add a wood shelf to the previously built level, then as­semble the top post to the bottom post by using two (2)
beams and two (2) braces. One (1) rivet from each beam
and brace must be placed in the top hole of the bottom
post, and the bottom hole of the top post (see figure D).
After all beams and braces are in place, tap lightly to
properly seat the rivets.

Post

Slot
Down

Wood Shelf

Step

4

Add a wood shelf to the previously built level, then con­tinue by adding the fourth and fifth level to the unit using
two (2) beams and two (2) braces per level. Tap lightly to
properly seat the rivets and add the final wood shelves to
the unit.