Edsal HR153060 User Manual
Steel Storage Rack
A - Beams
B - Braces
D- Woodboard Shelf
MODEL NUMBER
HR153060
E - Post Coupler
C - Post
HR153060 4 Shelf
HR153060 4 Shelf
HR153060 4 Shelf
Description
A - Beams
B - Braces
C - Post
D - Woodboard
E - Coupler
Safety Instructions
Safety Instructions
Safety Instructions
Qty.
8
8
8
4
4
-
60”h x 15”d x 30”w
-
60”h x 15”d x 30”w
-
60”h x 15”d x 30”w
Part Number
XHBE 2902
XHBE 1402
HXPT 3002
RPB 21530
XHPC 0403
Part Size
29 3/4”
14 3/4”
30”
15” x 30”
4”
Proper Installation Techniques For Tab Engagement
Proper Installation Techniques For Tab Engagement
Proper Installation Techniques For Tab Engagement
A - Tab Overlay
Brace holes are over
post tabs, and the
brace is flush to the
post.
Brace Is Flush To Post
B - Partial Engagement C - Full Engagement
Apply downward pressure to
the brace by hand, to partially seat the tabs.
Downward Hand Pressure
Holes Over Tabs
Tap brace down lightly with
a mallet to properly seat
the tabs.
Tap Lightly
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
General Instructions
General Instructions
General Instructions
Assembly is done with the holes of the beams and braces fitting into the tabs of the post (See “Proper Installation
Techniques For Tab Engagement”). A rubber mallet may be used on the beams and braces to seat the tabs properly.
A hammer can also be used, providing one uses a cloth or a block of wood between the hammer head and the parts to
prevent damage. Tap gently and be sure the tabs are straight and fully engaged.
During shipping and handling some of the tabs of the post that are used for engaging the beams and braces may
have become closed. Visually inspect all the post. If it is found that some tabs are closed,
use a small tipped screwdriver and from behind the post push the tabs slightly to re-open.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Work Force manufacturing facility at, (773) 475-3000 and request customer service.
We can also be reached on the internet at the following email address : customerservice@edsal.com.
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609
www.edsal.com
Assembly Instructions for HR153060
Assembly Instructions for HR153060
Assembly Instructions for HR153060
Step
1
Figure A
Post
Brace
Assemble two (2) post with one (1) brace (see figure A).
Skipping one (1) tab from the bottom of the post, place the
holes of the brace over the tab of the post with the shelf
ledge facing up (see figure B). Tap lightly to seat tabs. Repeat with two (2) post and one (1) brace. Assemble the two
(2) post end units with two (2) beams (see figure C). Skip
one (1) tab from the bottom of post, tap lightly to seat beams.
Figure B
Note:
Post are
directional.
The tab must
point up.
Tap Lightly
Shelf Ledge
Post Tabs Point Up
Figure C
Beam
Step
2
Woodboard Shelf
Start by adding a woodboard shelf to the level previously
built, then continue working by adding the second level
using two (2) beams and two (2) braces in the post tabs
of your desired location. Again place the holes of the
beams and braces over the post tabs with the shelf
ledge facing up and tap lightly to seat the tabs.
IMPORTANT NOTE : Make sure all beam / brace holes are fully seated into the tabs of the post.
IMPORTANT NOTE : Make sure all beam / brace holes are fully seated into the tabs of the post.
IMPORTANT NOTE : Make sure all beam / brace holes are fully seated into the tabs of the post.
Step
3
Figure D
Add a woodboard shelf to the previously built level, then
assemble the top post to the bottom post by using four
(4) of the post couplers. Place the couplers into the top of
the bottom post, and the bottom of the top post and tap
down to properly seat (see figure D). Continue by adding
the third level of beams and braces just above the post
couplers. Again tap lightly to seat the tabs.
Note:
Post are
directional.
The tab must
point up.
Top Post
Post Coupler
Bottom Post
Step
4
Woodboard Shelf
Add a woodboard shelf to the previously built level, then
continue by adding the final level of beams and braces to
the unit. Tap lightly to properly seat the tabs and add the
final woodboard shelf to the top of the unit.
Loading...